pimoroni-pico/drivers/bme68x/bme68x.cpp

121 lines
4.5 KiB
C++

#include "bme68x.hpp"
#include "pico/stdlib.h"
namespace pimoroni {
bool BME68X::init() {
int8_t result = 0;
if(interrupt != PIN_UNUSED) {
gpio_set_function(interrupt, GPIO_FUNC_SIO);
gpio_set_dir(interrupt, GPIO_IN);
gpio_pull_up(interrupt);
}
i2c_interface.i2c = i2c;
i2c_interface.address = address;
device.intf_ptr = &i2c_interface;
device.intf = bme68x_intf::BME68X_I2C_INTF;
device.read = (bme68x_read_fptr_t)&read_bytes;
device.write = (bme68x_write_fptr_t)&write_bytes;
device.delay_us = (bme68x_delay_us_fptr_t)&delay_us;
device.amb_temp = 20;
result = bme68x_init(&device);
bme68x_check_rslt("bme68x_init", result);
if(result != BME68X_OK) return false;
result = bme68x_get_conf(&conf, &device);
bme68x_check_rslt("bme68x_get_conf", result);
if(result != BME68X_OK) return false;
configure(BME68X_FILTER_OFF, BME68X_ODR_NONE, BME68X_OS_16X, BME68X_OS_1X, BME68X_OS_2X);
return true;
}
bool BME68X::configure(uint8_t filter, uint8_t odr, uint8_t os_humidity, uint8_t os_pressure, uint8_t os_temp) {
int8_t result = 0;
conf.filter = filter;
conf.odr = odr;
conf.os_hum = os_humidity;
conf.os_pres = os_pressure;
conf.os_temp = os_temp;
bme68x_set_conf(&conf, &device);
bme68x_check_rslt("bme68x_set_conf", result);
if(result != BME68X_OK) return false;
return true;
}
bool BME68X::read_forced(bme68x_data *data, uint16_t heater_temp, uint16_t heater_duration) {
int8_t result = 0;
uint8_t n_fields;
uint32_t delay_period;
heatr_conf.enable = BME68X_ENABLE;
heatr_conf.heatr_temp = heater_temp;
heatr_conf.heatr_dur = heater_duration;
result = bme68x_set_heatr_conf(BME68X_FORCED_MODE, &heatr_conf, &device);
bme68x_check_rslt("bme68x_set_heatr_conf", result);
if(result != BME68X_OK) return false;
result = bme68x_set_op_mode(BME68X_FORCED_MODE, &device);
bme68x_check_rslt("bme68x_set_op_mode", result);
if(result != BME68X_OK) return false;
delay_period = bme68x_get_meas_dur(BME68X_FORCED_MODE, &conf, &device) + (heatr_conf.heatr_dur * 1000);
// Could probably just call sleep_us here directly, I guess the API uses this internally
device.delay_us(delay_period, device.intf_ptr);
result = bme68x_get_data(BME68X_FORCED_MODE, data, &n_fields, &device);
bme68x_check_rslt("bme68x_get_data", result);
if(result != BME68X_OK) return false;
return true;
}
/*
Will read profile_length results with the given temperatures and duration multipliers into the results array.
Blocks until it has a valid result for each temp/duration, and returns the entire set in the given order.
*/
bool BME68X::read_parallel(bme68x_data *results, uint16_t *profile_temps, uint16_t *profile_durations, size_t profile_length) {
int8_t result;
bme68x_data data[3]; // Parallel & Sequential mode read 3 simultaneous fields
uint8_t n_fields;
uint32_t delay_period;
heatr_conf.enable = BME68X_ENABLE;
heatr_conf.heatr_temp_prof = profile_temps;
heatr_conf.heatr_dur_prof = profile_durations;
heatr_conf.profile_len = profile_length;
heatr_conf.shared_heatr_dur = 140 - (bme68x_get_meas_dur(BME68X_PARALLEL_MODE, &conf, &device) / 1000);
result = bme68x_set_heatr_conf(BME68X_PARALLEL_MODE, &heatr_conf, &device);
bme68x_check_rslt("bme68x_set_heatr_conf", result);
if(result != BME68X_OK) return false;
result = bme68x_set_op_mode(BME68X_PARALLEL_MODE, &device);
bme68x_check_rslt("bme68x_set_op_mode", result);
if(result != BME68X_OK) return false;
while (1) {
delay_period = bme68x_get_meas_dur(BME68X_PARALLEL_MODE, &conf, &device) + (heatr_conf.shared_heatr_dur * 1000);
device.delay_us(delay_period, device.intf_ptr);
result = bme68x_get_data(BME68X_PARALLEL_MODE, data, &n_fields, &device);
if(result == BME68X_W_NO_NEW_DATA) continue;
bme68x_check_rslt("bme68x_get_data", result);
if(result != BME68X_OK) return false;
for(auto i = 0u; i < n_fields; i++) {
results[data[i].gas_index] = data[i];
if(data[i].gas_index == profile_length - 1) return true;
}
}
return true;
}
}