92 lines
3.0 KiB
Python
92 lines
3.0 KiB
Python
import time
|
|
from pimoroni import NORMAL_DIR # , REVERSED_DIR
|
|
from inventor import Inventor2040W, MOTOR_A
|
|
|
|
"""
|
|
A program that profiles the speed of a motor across its PWM
|
|
duty cycle range using the attached encoder for feedback.
|
|
"""
|
|
|
|
GEAR_RATIO = 50 # The gear ratio of the motor
|
|
|
|
DIRECTION = NORMAL_DIR # The direction to spin the motor in. NORMAL_DIR (0), REVERSED_DIR (1)
|
|
SPEED_SCALE = 5.4 # The scaling to apply to the motor's speed. Set this to the maximum measured speed
|
|
ZERO_POINT = 0.0 # The duty cycle that corresponds with zero speed when plotting the motor's speed as a straight line
|
|
DEAD_ZONE = 0.0 # The duty cycle below which the motor's friction prevents it from moving
|
|
|
|
DUTY_STEPS = 100 # How many duty cycle steps to sample the speed of
|
|
SETTLE_TIME = 0.1 # How long to wait after changing motor duty cycle
|
|
CAPTURE_TIME = 0.2 # How long to capture the motor's speed at each step
|
|
|
|
# Create a new Inventor2040W and get a motor and encoder from it
|
|
board = Inventor2040W(motor_gear_ratio=GEAR_RATIO)
|
|
m = board.motors[MOTOR_A]
|
|
enc = board.encoders[MOTOR_A]
|
|
|
|
# Set the motor's speed scale, zeropoint, and deadzone
|
|
m.speed_scale(SPEED_SCALE)
|
|
m.zeropoint(ZERO_POINT)
|
|
m.deadzone(DEAD_ZONE)
|
|
|
|
# Set the motor and encoder's direction
|
|
m.direction(DIRECTION)
|
|
enc.direction(DIRECTION)
|
|
|
|
|
|
# Function that performs a single profiling step
|
|
def profile_at_duty(duty):
|
|
# Set the motor to a new duty cycle and wait for it to settle
|
|
if DIRECTION == 1:
|
|
m.duty(0.0 - duty)
|
|
else:
|
|
m.duty(duty)
|
|
time.sleep(SETTLE_TIME)
|
|
|
|
# Perform a dummy capture to clear the encoder
|
|
enc.capture()
|
|
|
|
# Wait for the capture time to pass
|
|
time.sleep(CAPTURE_TIME)
|
|
|
|
# Perform a capture and read the measured speed
|
|
capture = enc.capture()
|
|
measured_speed = capture.revolutions_per_second
|
|
|
|
# These are some alternate speed measurements from the encoder
|
|
# measured_speed = capture.revolutions_per_minute
|
|
# measured_speed = capture.degrees_per_second
|
|
# measured_speed = capture.radians_per_second
|
|
|
|
# Print out the expected and measured speeds, as well as their difference
|
|
print("Duty = ", m.duty(), ", Expected = ", m.speed(), ", Measured = ", measured_speed, ", Diff = ", m.speed() - measured_speed, sep="")
|
|
|
|
|
|
# Enable the motor to get started
|
|
m.enable()
|
|
|
|
print("Profiler Starting...")
|
|
|
|
# Profile from 0% up to one step below 100%
|
|
for i in range(DUTY_STEPS):
|
|
profile_at_duty(i / DUTY_STEPS)
|
|
|
|
# Profile from 100% down to one step above 0%
|
|
for i in range(DUTY_STEPS):
|
|
profile_at_duty((DUTY_STEPS - i) / DUTY_STEPS)
|
|
|
|
# Profile from 0% down to one step above -100%
|
|
for i in range(DUTY_STEPS):
|
|
profile_at_duty(-i / DUTY_STEPS)
|
|
|
|
# Profile from -100% up to one step below 0%
|
|
for i in range(DUTY_STEPS):
|
|
profile_at_duty(-(DUTY_STEPS - i) / DUTY_STEPS)
|
|
|
|
# Profile 0% again
|
|
profile_at_duty(0)
|
|
|
|
print("Profiler Finished...")
|
|
|
|
# Disable the motor now the profiler has finished
|
|
m.disable()
|