Tasmota/lib/IRremoteESP8266-2.5.2.03/examples/IRsendDemo/IRsendDemo.ino

72 lines
2.7 KiB
Arduino
Raw Normal View History

/* IRremoteESP8266: IRsendDemo - demonstrates sending IR codes with IRsend.
*
* Version 1.0 April, 2017
* Based on Ken Shirriff's IrsendDemo Version 0.1 July, 2009,
* Copyright 2009 Ken Shirriff, http://arcfn.com
*
* An IR LED circuit *MUST* be connected to the ESP8266 on a pin
* as specified by kIrLed below.
*
* TL;DR: The IR LED needs to be driven by a transistor for a good result.
*
* Suggested circuit:
* https://github.com/markszabo/IRremoteESP8266/wiki#ir-sending
*
* Common mistakes & tips:
* * Don't just connect the IR LED directly to the pin, it won't
* have enough current to drive the IR LED effectively.
* * Make sure you have the IR LED polarity correct.
* See: https://learn.sparkfun.com/tutorials/polarity/diode-and-led-polarity
* * Typical digital camera/phones can be used to see if the IR LED is flashed.
* Replace the IR LED with a normal LED if you don't have a digital camera
* when debugging.
* * Avoid using the following pins unless you really know what you are doing:
* * Pin 0/D3: Can interfere with the boot/program mode & support circuits.
* * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will interfere.
* * Pin 3/RX/RXD0: Any serial transmissions to the ESP8266 will interfere.
* * ESP-01 modules are tricky. We suggest you use a module with more GPIOs
* for your first time. e.g. ESP-12 etc.
*/
#ifndef UNIT_TEST
#include <Arduino.h>
#endif
#include <IRremoteESP8266.h>
#include <IRsend.h>
const uint16_t kIrLed = 4; // ESP8266 GPIO pin to use. Recommended: 4 (D2).
IRsend irsend(kIrLed); // Set the GPIO to be used to sending the message.
// Example of data captured by IRrecvDumpV2.ino
uint16_t rawData[67] = {9000, 4500, 650, 550, 650, 1650, 600, 550, 650, 550,
600, 1650, 650, 550, 600, 1650, 650, 1650, 650, 1650,
600, 550, 650, 1650, 650, 1650, 650, 550, 600, 1650,
650, 1650, 650, 550, 650, 550, 650, 1650, 650, 550,
650, 550, 650, 550, 600, 550, 650, 550, 650, 550,
650, 1650, 600, 550, 650, 1650, 650, 1650, 650, 1650,
650, 1650, 650, 1650, 650, 1650, 600};
void setup() {
irsend.begin();
Serial.begin(115200, SERIAL_8N1, SERIAL_TX_ONLY);
}
void loop() {
#if SEND_NEC
Serial.println("NEC");
irsend.sendNEC(0x00FFE01FUL, 32);
#endif // SEND_NEC
delay(2000);
#if SEND_SONY
Serial.println("Sony");
irsend.sendSony(0xa90, 12, 2);
#endif // SEND_SONY
delay(2000);
#if SEND_RAW
Serial.println("a rawData capture from IRrecvDumpV2");
irsend.sendRaw(rawData, 67, 38); // Send a raw data capture at 38kHz.
#endif // SEND_RAW
delay(2000);
}