diff --git a/lib/lib_display/Epaper_29-gemu-1.0/epd2in9.cpp b/lib/lib_display/Epaper_29-gemu-1.0/epd2in9.cpp
index 434a14b89..96b83645e 100644
--- a/lib/lib_display/Epaper_29-gemu-1.0/epd2in9.cpp
+++ b/lib/lib_display/Epaper_29-gemu-1.0/epd2in9.cpp
@@ -28,6 +28,8 @@
 #include "epd2in9.h"
 
 
+#define EPD_29_V2
+
 Epd::Epd(int16_t width, int16_t height) :
 Paint(width,height) {
 }
@@ -126,6 +128,32 @@ int Epd::Init(const unsigned char* lut) {
     width = EPD_WIDTH;
     height = EPD_HEIGHT;
 
+#ifdef EPD_29_V2
+    /* EPD hardware init start */
+    WaitUntilIdle();
+    SendCommand(0x12);  //SWRESET
+    WaitUntilIdle();
+
+    SendCommand(0x01); //Driver output control
+    SendData(0x27);
+    SendData(0x01);
+    SendData(0x00);
+
+    SendCommand(0x11); //data entry mode
+    SendData(0x03);
+
+    SetMemoryArea(0, 0, width-1, height-1);
+
+    SendCommand(0x21); //  Display update control
+    SendData(0x00);
+    SendData(0x80);
+
+    SetMemoryPointer(0, 0);
+    WaitUntilIdle();
+
+    SetLut_by_host(lut_full_update);
+
+#else
     /* EPD hardware init start */
     this->lut = lut;
     Reset();
@@ -146,6 +174,7 @@ int Epd::Init(const unsigned char* lut) {
     SendCommand(DATA_ENTRY_MODE_SETTING);
     SendData(0x03);                     // X increment; Y increment
     SetLut(this->lut);
+#endif
     /* EPD hardware init end */
     return 0;
 }
@@ -172,6 +201,11 @@ void Epd::SendData(unsigned char data) {
  *  @brief: Wait until the busy_pin goes LOW
  */
 void Epd::WaitUntilIdle(void) {
+
+#ifdef EPD_29_V2
+  delay(100);
+#endif
+
   return;
     //while(DigitalRead(busy_pin) == HIGH) {      //LOW: idle, HIGH: busy
     //    DelayMs(100);
@@ -190,6 +224,34 @@ void Epd::Reset(void) {
     //delay(200);
 }
 
+#ifdef EPD_29_V2
+void Epd::SetLut(const unsigned char *lut) {
+	unsigned char count;
+	SendCommand(0x32);
+	for(count=0; count<153; count++)
+		SendData(lut[count]);
+	WaitUntilIdle();
+}
+
+
+void Epd::SetLut_by_host(const unsigned char *lut) {
+  SetLut((unsigned char *)lut);
+	SendCommand(0x3f);
+	SendData(*(lut+153));
+	SendCommand(0x03);	// gate voltage
+	SendData(*(lut+154));
+	SendCommand(0x04);	// source voltage
+	SendData(*(lut+155));	// VSH
+	SendData(*(lut+156));	// VSH2
+	SendData(*(lut+157));	// VSL
+	SendCommand(0x2c);		// VCOM
+	SendData(*(lut+158));
+}
+#else
+
+void Epd::SetLut_by_host(const unsigned char *lut)  {
+
+}
 /**
  *  @brief: set the look-up table register
  */
@@ -201,6 +263,7 @@ void Epd::SetLut(const unsigned char* lut) {
         SendData(this->lut[i]);
     }
 }
+#endif
 
 /**
  *  @brief: put an image buffer to the frame memory.
@@ -310,6 +373,23 @@ void Epd::DisplayFrame(void) {
     WaitUntilIdle();
 }
 
+
+#ifdef EPD_29_V2
+/**
+ *  @brief: private function to specify the memory area for data R/W
+ */
+void Epd::SetMemoryArea(int x_start, int y_start, int x_end, int y_end) {
+    SendCommand(0x44);
+    /* x point must be the multiple of 8 or the last 3 bits will be ignored */
+    SendData((x_start >> 3) & 0xFF);
+    SendData((x_end >> 3) & 0xFF);
+    SendCommand(0x45);
+    SendData(y_start & 0xFF);
+    SendData((y_start >> 8) & 0xFF);
+    SendData(y_end & 0xFF);
+    SendData((y_end >> 8) & 0xFF);
+}
+#else
 /**
  *  @brief: private function to specify the memory area for data R/W
  */
@@ -324,7 +404,24 @@ void Epd::SetMemoryArea(int x_start, int y_start, int x_end, int y_end) {
     SendData(y_end & 0xFF);
     SendData((y_end >> 8) & 0xFF);
 }
+#endif
 
+
+#ifdef EPD_29_V2
+
+/**
+ *  @brief: private function to specify the start point for data R/W
+ */
+void Epd::SetMemoryPointer(int x, int y) {
+    SendCommand(0x4E);
+    /* x point must be the multiple of 8 or the last 3 bits will be ignored */
+    SendData((x >> 3) & 0xFF);
+    SendCommand(0x4F);
+    SendData(y & 0xFF);
+    SendData((y >> 8) & 0xFF);
+    WaitUntilIdle();
+}
+#else
 /**
  *  @brief: private function to specify the start point for data R/W
  */
@@ -337,6 +434,7 @@ void Epd::SetMemoryPointer(int x, int y) {
     SendData((y >> 8) & 0xFF);
     WaitUntilIdle();
 }
+#endif
 
 /**
  *  @brief: After this command is transmitted, the chip would enter the
@@ -349,6 +447,56 @@ void Epd::Sleep() {
     WaitUntilIdle();
 }
 
+#ifdef EPD_29_V2
+
+const unsigned char lut_partial_update[159] =
+{
+0x0,0x40,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x80,0x80,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x40,0x40,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x80,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0A,0x0,0x0,0x0,0x0,0x0,0x2,
+0x1,0x0,0x0,0x0,0x0,0x0,0x0,
+0x1,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x0,0x0,0x0,0x0,0x0,0x0,0x0,
+0x22,0x22,0x22,0x22,0x22,0x22,0x0,0x0,0x0,
+0x22,0x17,0x41,0xB0,0x32,0x36,
+};
+
+const unsigned char lut_full_update[159] =
+{
+0x80,	0x66,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x40,	0x0,	0x0,	0x0,
+0x10,	0x66,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x20,	0x0,	0x0,	0x0,
+0x80,	0x66,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x40,	0x0,	0x0,	0x0,
+0x10,	0x66,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x20,	0x0,	0x0,	0x0,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x14,	0x8,	0x0,	0x0,	0x0,	0x0,	0x1,
+0xA,	0xA,	0x0,	0xA,	0xA,	0x0,	0x1,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x14,	0x8,	0x0,	0x1,	0x0,	0x0,	0x1,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x1,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x0,	0x0,	0x0,	0x0,	0x0,	0x0,	0x0,
+0x44,	0x44,	0x44,	0x44,	0x44,	0x44,	0x0,	0x0,	0x0,
+0x22,	0x17,	0x41,	0x0,	0x32,	0x36
+};
+
+#else
+
 const unsigned char lut_full_update[] =
 {
     0x02, 0x02, 0x01, 0x11, 0x12, 0x12, 0x22, 0x22,
@@ -364,7 +512,7 @@ const unsigned char lut_partial_update[] =
     0x00, 0x00, 0x00, 0x00, 0x13, 0x14, 0x44, 0x12,
     0x00, 0x00, 0x00, 0x00, 0x00, 0x00
 };
-
+#endif // EPD_29_V2
 
 #define PIN_OUT_SET 0x60000304
 #define PIN_OUT_CLEAR 0x60000308
diff --git a/lib/lib_display/Epaper_29-gemu-1.0/epd2in9.h b/lib/lib_display/Epaper_29-gemu-1.0/epd2in9.h
index bf0863cd0..3be3071ec 100644
--- a/lib/lib_display/Epaper_29-gemu-1.0/epd2in9.h
+++ b/lib/lib_display/Epaper_29-gemu-1.0/epd2in9.h
@@ -106,6 +106,8 @@ private:
     void SetLut(const unsigned char* lut);
     void SetMemoryArea(int x_start, int y_start, int x_end, int y_end);
     void SetMemoryPointer(int x, int y);
+    void SetLut_by_host(const unsigned char* lut);
+
     //void fastSPIwrite(uint8_t d,uint8_t dc);
 };
 
diff --git a/tasmota/displaydesc/ST7262_rgb16_display.ini b/tasmota/displaydesc/ST7262_rgb16_display.ini
index 413af0bb1..80b210600 100644
--- a/tasmota/displaydesc/ST7262_rgb16_display.ini
+++ b/tasmota/displaydesc/ST7262_rgb16_display.ini
@@ -1,5 +1,9 @@
 :H,ST7262,800,480,16,RGB,40,41,39,42,2,15,16,4,45,48,47,21,14,8,3,46,9,1,5,6,7,14
 :S,2,1,1,0,40,20
 :V,0,8,4,8,0,8,4,8,1
-:TI1,5a,*,*,-1,38
+:0,00
+:1,01
+:2,02
+:3,03
+:TI1,5d,*,*,-1,38
 #