From 63b001021c5166b63078f782f177b6412dc7718f Mon Sep 17 00:00:00 2001 From: Theo Arends <11044339+arendst@users.noreply.github.com> Date: Sat, 23 Nov 2019 13:59:18 +0100 Subject: [PATCH] Redesign changelog --- tasmota/CHANGELOG.md | 3182 ++++++++++++++++++++-------------------- tasmota/_changelog.ino | 1987 ------------------------- 2 files changed, 1606 insertions(+), 3563 deletions(-) delete mode 100644 tasmota/_changelog.ino diff --git a/tasmota/CHANGELOG.md b/tasmota/CHANGELOG.md index 2c7e2578a..cdfc8f659 100644 --- a/tasmota/CHANGELOG.md +++ b/tasmota/CHANGELOG.md @@ -1,1988 +1,2018 @@ - ## Unreleased (development) ### 7.0.0.6 20191122 - * Add colorpicker to WebUI by Christian Staars (#6984) + +- Add colorpicker to WebUI by Christian Staars (#6984) ### 7.0.0.5 20191118 - * Fix boot loop regression - * Add command TempOffset -12.6 .. 12.6 to set global temperature sensor offset (#6958) - * Fix check deepsleep for valid values in Settings (#6961) - * Fix Wifi instability when light is on, due to sleep=0 (#6961, #6608) - * Add hardware detection to be overruled with SetOption51 (#6969) + +- Fix boot loop regression +- Add command ``TempOffset -12.6 .. 12.6`` to set global temperature sensor offset (#6958) +- Fix check deepsleep for valid values in Settings (#6961) +- Fix Wifi instability when light is on, due to sleep=0 (#6961, #6608) +- Add hardware detection to be overruled with ``SetOption51`` (#6969) ### 7.0.0.4 20191108 - * Add command WifiPower 0 .. 20.5 to set Wifi Output Power which will be default set to 17dBm - * Change supported PCF8574 I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time - * Change supported PCF8574A I2C address range to 0x39 - 0x3F allowing other I2C devices with address 0x38 to be used at the same time - * Change supported MCP230xx I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time - * Add Keep last channels values when Color command end with '=' (#6799) - * Add support for I2C sensor TLS2591 Light Intensity sensor (#6873) - * Change Kept only NEC/RC5/RC6/HASH IR protocols in standard Tasmota, all other protocols require Tasmota-IR, saving 4K - * Add command SetOption76 0/1 to enable incrementing bootcount when deepsleep is enabled (#6930) - * Change Reset erase end address from as seen by SDK (getFlashChipSize) to full flash size (getFlashChipRealSize) - * Change Zigbee log verbosity reduction + +- Add command ``WifiPower 0 .. 20.5`` to set Wifi Output Power which will be default set to 17dBm +- Change supported PCF8574 I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time +- Change supported PCF8574A I2C address range to 0x39 - 0x3F allowing other I2C devices with address 0x38 to be used at the same time +- Change supported MCP230xx I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time +- Add Keep last channels values when Color command end with '=' (#6799) +- Add support for I2C sensor TLS2591 Light Intensity sensor (#6873) +- Change Kept only NEC/RC5/RC6/HASH IR protocols in standard Tasmota, all other protocols require Tasmota-IR, saving 4K +- Add command ``SetOption76 0/1`` to enable incrementing bootcount when deepsleep is enabled (#6930) +- Change Reset erase end address from as seen by SDK (getFlashChipSize) to full flash size (getFlashChipRealSize) +- Change Zigbee log verbosity reduction ### 7.0.0.3 20191103 - * Add command I2cDriver for I2C driver runtime control using document I2CDEVICES.md - * Fix random crash caused by UPNP flood - * Add support for Honeywell HPMA115S0 particle concentration sensor by David Hunt (#6843) - * Remove driver xsns_12_ads1115_i2cdev replaced by xsns_12_ads1115 + +- Add command ``I2cDriver`` for I2C driver runtime control using document I2CDEVICES.md +- Fix random crash caused by UPNP flood +- Add support for Honeywell HPMA115S0 particle concentration sensor by David Hunt (#6843) +- Remove driver xsns_12_ads1115_i2cdev replaced by xsns_12_ads1115 ### 7.0.0.2 20191102 - * Add command WebColor19 to control color of Module and Name (#6811) - * Add support for Honeywell I2C HIH series Humidity and Temperetaure sensor (#6808) - * Fix wrong Dimmer behavior introduced with #6799 when SetOption37 < 128 - * Change add DS18x20 support in Tasmota-IR - * Add Zigbee command support, considered as v1.0 for full Zigbee support - * Fix Reduce flash size after change to IRremoteESP8266 v2.7.0 + +- Add command ``WebColor19`` to control color of Module and Name (#6811) +- Add support for Honeywell I2C HIH series Humidity and Temperetaure sensor (#6808) +- Fix wrong Dimmer behavior introduced with #6799 when ``SetOption37`` < 128 +- Change add DS18x20 support in Tasmota-IR +- Add Zigbee command support, considered as v1.0 for full Zigbee support +- Fix Reduce flash size after change to IRremoteESP8266 v2.7.0 ### 7.0.0.1 20191027 - * Remove update support for versions before 6.0 - * Change default GUI to dark theme - * Add command SetOption73 0/1 to re-enable HTTP Cross-Origin Resource Sharing (CORS) now default disabled (#6767) - * Add frequency to ADE7953 energy monitor as used in Shelly 2.5 by ljakob (#6778) - * Add command SetOption74 0/1 to enable DS18x20 internal pull-up and remove define DS18B20_INTERNAL_PULLUP (#6795) - * Fix better control of RGB/White when SetOption37 >128, added Dimmer1 and Dimmer2 commands (#6714) - * Add hide Alexa objects with friendlyname starting with '$' (#6722, #6762) - * Add command SetOption75 0/1 to switch between grouptopic (0) using fulltopic replacing %topic% or (1) is cmnd/ (#6779) - * Change Update IRremoteESP8266 to v2.7.0 + +- Remove update support for versions before 6.0 +- Change default GUI to dark theme +- Add command ``SetOption73 0/1`` to re-enable HTTP Cross-Origin Resource Sharing (CORS) now default disabled (#6767) +- Add frequency to ADE7953 energy monitor as used in Shelly 2.5 by ljakob (#6778) +- Add command ``SetOption74 0/1`` to enable DS18x20 internal pull-up and remove define DS18B20_INTERNAL_PULLUP (#6795) +- Fix better control of RGB/White when ``SetOption37`` >128, added ``Dimmer1`` and ``Dimmer2`` commands (#6714) +- Add hide Alexa objects with friendlyname starting with '$' (#6722, #6762) +- Add command ``SetOption75 0/1`` to switch between grouptopic (0) using fulltopic replacing %topic% or (1) is cmnd/\ (#6779) +- Change IRremoteESP8266 library to v2.7.0 ### 6.7.1.1 20191026 - * Change ArduinoSlave to TasmotaSlave (Experimental) - * Add support for Tuya battery powered devices (#6735) - * Change repository name from Sonoff-Tasmota to Tasmota - * Change all code references from Sonoff to Tasmota + +- Change ArduinoSlave to TasmotaSlave +- Add support for Tuya battery powered devices (#6735) +- Change repository name from Sonoff-Tasmota to Tasmota and all code references from Sonoff to Tasmota ## Released + ### 6.7.1 20191026 - * Release - * Fix on energy monitoring devices using PowerDelta Exception0 with epc1:0x4000dce5 = Divide by zero (#6750) - * Fix Script array bug (#6751) + +- Release +- Fix on energy monitoring devices using PowerDelta Exception0 with epc1:0x4000dce5 = Divide by zero (#6750) +- Fix Script array bug (#6751) ### 6.7.0 20191025 - * Release + +- Release ### 6.6.0.21 20191022 - * Remove support for WPS and SmartConfig in favour of Web server (!) based WifiManager (#6680) - * Remove binary sonoff-classic (#6680) - * Remove command SetOption2 + +- Remove support for WPS and SmartConfig in favour of Web server (!) based WifiManager (#6680) +- Remove binary sonoff-classic (#6680) +- Remove command SetOption2 ### 6.6.0.20 20191018 - * Add command SetOption65 0/1 to disable (1) fast power cycle detection fixing unwanted brownout trigger - * Add absolute PowerDelta using command PowerDelta 101..32000 where 101 = 101-100 = 1W, 202 = 202-100 = 102W (#5901) - * Add support for EX-Store WiFi Dimmer V4 (#5856) - * Add ZigbeeRead command and many improvements (#6095) - * Add ArduinoSlave driver (EXPERIMENTAL) + +- Add command SetOption65 0/1 to disable (1) fast power cycle detection fixing unwanted brownout trigger +- Add absolute PowerDelta using command PowerDelta 101..32000 where 101 = 101-100 = 1W, 202 = 202-100 = 102W (#5901) +- Add support for EX-Store WiFi Dimmer V4 (#5856) +- Add ZigbeeRead command and many improvements (#6095) +- Add ArduinoSlave driver (EXPERIMENTAL) ### 6.6.0.19 20191018 - * Replace obsolete xsns_23_sdm120 with xnrg_08_sdm120 and consolidate define USE_SDM120 - * Replace obsolete xsns_25_sdm630 with xnrg_10_sdm630 and consolidate define USE_SDM630 - * Replace obsolete xsns_49_solaxX1 with xnrg_12_solaxX1 (#6677) + +- Replace obsolete xsns_23_sdm120 with xnrg_08_sdm120 and consolidate define USE_SDM120 +- Replace obsolete xsns_25_sdm630 with xnrg_10_sdm630 and consolidate define USE_SDM630 +- Replace obsolete xsns_49_solaxX1 with xnrg_12_solaxX1 (#6677) ### 6.6.0.18 20191010 - * Add command DimmerRange in Light module to support 2 byte dimming ranges from Tuya - * Add Zigbee additional commands and sending messages to control devices (#6095) - * Fix Rules were not triggered with IR unknown protocol or in sonoff-it (#6629) - * Add define USE_DEEPSLEEP and command DeepSleepTime 0 or 10..86400 (seconds) to enter deepsleep mode (#6638) - * Add define USE_SONOFF_RF to enable/disable Sonoff Rf support (#6648) - * Add incremental beeps to Ifan03 remote control fan speed buttons (#6636) - * Add rule support after every command execution like Fanspeed#Data=2 (#6636) - * Fix handling of ligth channels when pwm_multichannel (Option68) is enabled - * Add WebUI for multiple, independent PWM channels - * Remove default DS18B20 driver and only support define DS18x20 (#6647) - * Add support for PMS3003 dust particle sensor - * Change Sonoff L1 support by adding define USE_SONOFF_L1 + +- Add command DimmerRange in Light module to support 2 byte dimming ranges from Tuya +- Add Zigbee additional commands and sending messages to control devices (#6095) +- Fix Rules were not triggered with IR unknown protocol or in sonoff-it (#6629) +- Add define USE_DEEPSLEEP and command DeepSleepTime 0 or 10..86400 (seconds) to enter deepsleep mode (#6638) +- Add define USE_SONOFF_RF to enable/disable Sonoff Rf support (#6648) +- Add incremental beeps to Ifan03 remote control fan speed buttons (#6636) +- Add rule support after every command execution like Fanspeed#Data=2 (#6636) +- Fix handling of ligth channels when pwm_multichannel (Option68) is enabled +- Add WebUI for multiple, independent PWM channels +- Remove default DS18B20 driver and only support define DS18x20 (#6647) +- Add support for PMS3003 dust particle sensor +- Change Sonoff L1 support by adding define USE_SONOFF_L1 ### 6.6.0.17 20191009 - * Add command SetOption34 0..255 to set backlog delay. Default value is 200 (mSeconds) (#6562) - * Add command Gpio 255 to show physical GPIO configuration of all non-flash pins (#6407) + +- Add command SetOption34 0..255 to set backlog delay. Default value is 200 (mSeconds) (#6562) +- Add command Gpio 255 to show physical GPIO configuration of all non-flash pins (#6407) ### 6.6.0.16 20191008 - * Change PZEM004T default address mask from 0.0.0.x to 192.168.1.x for legacy reason (#6585) - * Fix PZEM004T, PZEMAC and PZEMDC autodetection (#6585) - * Change light drivers internals to ease management + +- Change PZEM004T default address mask from 0.0.0.x to 192.168.1.x for legacy reason (#6585) +- Fix PZEM004T, PZEMAC and PZEMDC autodetection (#6585) +- Change light drivers internals to ease management ### 6.6.0.15 20191003 - * Change command PulseTime JSON message format and allow display of all pulsetimer information (#6519) - * Add support for Chint DDSU666 Modbus energy meter by Pablo Zerón - * Add support for SM2135 as used in Action LSC Smart Led E14 (#6495) - * Add command SetOption72 0/1 to switch between software (0) or hardware (1) energy total counter (#6561) - * Add Zigbee tracking of connected devices and auto-probing of Manuf/Model Ids - * Fix better handling of PWM White Temperature mode for Module 48 (#6534) + +- Change command PulseTime JSON message format and allow display of all pulsetimer information (#6519) +- Add support for Chint DDSU666 Modbus energy meter by Pablo Zerón +- Add support for SM2135 as used in Action LSC Smart Led E14 (#6495) +- Add command SetOption72 0/1 to switch between software (0) or hardware (1) energy total counter (#6561) +- Add Zigbee tracking of connected devices and auto-probing of Manuf/Model Ids +- Fix better handling of PWM White Temperature mode for Module 48 (#6534) ### 6.6.0.14 20190925 - * Change command Tariffx to allow time entries like 23 (hours), 1320 (minutes) or 23:00. NOTE: As this is development branch previous tariffs are lost! (#6488) - * Remove support for define USE_DS18x20_LEGACY and legacy DS18x20 driver (#6486) - * Add initial support for MQTT logging using command MqttLog (#6498) - * Add Zigbee more support - collect endpoints and clusters, added ZigbeeDump command - * Add initial support for shutters by Stefan Bode (#288) - * Add command to MCP230xx: sensor29 pin,0/1/2 for OFF/ON/TOGGLE - * Add initial support for PCF8574 I2C I/O Expander (currently output only) by Stefan Bode - * Add command SetOption71 0/1 to switch between different Modbus Active Energy registers on DDS238-2 energy meters (#6531) - * Change command SetOption43 to make it more general. Now supports PS_16_DZ driver too (#6544) - * Change command handling by moving buffers up in chain solving MQTTlog support (#6529) - * Change detection of non-MQTT commands by allowing non-space characters as delimiter (#6540) - * Fix TasmotaSerial: move serial send to IRAM for high speed baud rates + +- Change command Tariffx to allow time entries like 23 (hours), 1320 (minutes) or 23:00. NOTE: As this is development branch previous tariffs are lost! (#6488) +- Remove support for define USE_DS18x20_LEGACY and legacy DS18x20 driver (#6486) +- Add initial support for MQTT logging using command MqttLog (#6498) +- Add Zigbee more support - collect endpoints and clusters, added ZigbeeDump command +- Add initial support for shutters by Stefan Bode (#288) +- Add command to MCP230xx: sensor29 pin,0/1/2 for OFF/ON/TOGGLE +- Add initial support for PCF8574 I2C I/O Expander (currently output only) by Stefan Bode +- Add command SetOption71 0/1 to switch between different Modbus Active Energy registers on DDS238-2 energy meters (#6531) +- Change command SetOption43 to make it more general. Now supports PS_16_DZ driver too (#6544) +- Change command handling by moving buffers up in chain solving MQTTlog support (#6529) +- Change detection of non-MQTT commands by allowing non-space characters as delimiter (#6540) +- Fix TasmotaSerial: move serial send to IRAM for high speed baud rates ### 6.6.0.13 20190922 - * Add command EnergyReset4 x,x to initialize total usage for two tarrifs - * Add command EnergyReset5 x,x to initialize total export (or production) for two tarrifs - * Add command Sensor34 8,0 and Sensor34 8,1 to disable/enable JSON message on weight change over 4 gram - * Add JSON array index support to rules evaluation allowing trigger on ENERGY#POWER[2]>0.60 from JSON ..,"Power":[0.00,0.68],.. (#6160) + +- Add command EnergyReset4 x,x to initialize total usage for two tarrifs +- Add command EnergyReset5 x,x to initialize total export (or production) for two tarrifs +- Add command Sensor34 8,0 and Sensor34 8,1 to disable/enable JSON message on weight change over 4 gram +- Add JSON array index support to rules evaluation allowing trigger on ENERGY#POWER[2]>0.60 from JSON ..,"Power":[0.00,0.68],.. (#6160) ### 6.6.0.12 20190910 - * Redesign command Tariff to now default to 0 (=disabled) and allowing to set both Standard Time (ST) and Daylight Savings Time (DST) start hour - * Commands Tariff1 22,23 = Tariff1 (Off-Peak) ST,DST Tariff2 (Standard) 6,7 = Tariff2 ST,DST Tariff9 0/1 = Weekend toggle (1 = Off-Peak during weekend) - * Change rename "Data" to "Hash" and limit to 32 bits when receiving UNKNOWN IR protocol (see DECODE_HASH from IRremoteESP8266) - * Add command Gpios 255/All to show all available GPIO components (#6407) - * Change JSON output format for commands Adc, Adcs, Modules, Gpio and Gpios from list to dictionary (#6407) - * Add Zigbee support phase 3 - support for Xiaomi lumi.weather air quality sensor, Osram mini-switch - * Change energy sensors for three phase/channel support - * Add support for Shelly 2.5 dual energy (#6160) - * Add initial support for up to three PZEM-014/-016 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315) - * Add initial support for up to three PZEM-004T on serial connection with addresses x.x.x.1 (default), 2 and 3 (#2315) - * Add initial support for up to three PZEM-003/-017 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315) - * Add driver USE_SDM630_2 as future replacement for USE_SDM630 - Pls test and report - * Add command ModuleAddress 1/2/3 to set Pzem module address when a single module is connected (#2315) + +- Redesign command Tariff to now default to 0 (=disabled) and allowing to set both Standard Time (ST) and Daylight Savings Time (DST) start hour +- Commands Tariff1 22,23 = Tariff1 (Off-Peak) ST,DST Tariff2 (Standard) 6,7 = Tariff2 ST,DST Tariff9 0/1 = Weekend toggle (1 = Off-Peak during weekend) +- Change rename "Data" to "Hash" and limit to 32 bits when receiving UNKNOWN IR protocol (see DECODE_HASH from IRremoteESP8266) +- Add command Gpios 255/All to show all available GPIO components (#6407) +- Change JSON output format for commands Adc, Adcs, Modules, Gpio and Gpios from list to dictionary (#6407) +- Add Zigbee support phase 3 - support for Xiaomi lumi.weather air quality sensor, Osram mini-switch +- Change energy sensors for three phase/channel support +- Add support for Shelly 2.5 dual energy (#6160) +- Add initial support for up to three PZEM-014/-016 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315) +- Add initial support for up to three PZEM-004T on serial connection with addresses x.x.x.1 (default), 2 and 3 (#2315) +- Add initial support for up to three PZEM-003/-017 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315) +- Add driver USE_SDM630_2 as future replacement for USE_SDM630 - Pls test and report +- Add command ModuleAddress 1/2/3 to set Pzem module address when a single module is connected (#2315) ### 6.6.0.11 20190907 - * Change Settings crc calculation allowing short term backward compatibility - * Add support for up to 4 INA226 Voltage and Current sensors by Steve Rogers (#6342) - * Change Improve reliability of TasmotaSerial at 115200 bauds and reduce IRAM usage for Stage/pre-2.6 - * Add support for A4988 stepper-motor-driver-circuit by Tim Leuschner (#6370) - * Add support for Hiking DDS238-2 Modbus energy meter by Matteo Campanella (#6384) + +- Change Settings crc calculation allowing short term backward compatibility +- Add support for up to 4 INA226 Voltage and Current sensors by Steve Rogers (#6342) +- Change Improve reliability of TasmotaSerial at 115200 bauds and reduce IRAM usage for Stage/pre-2.6 +- Add support for A4988 stepper-motor-driver-circuit by Tim Leuschner (#6370) +- Add support for Hiking DDS238-2 Modbus energy meter by Matteo Campanella (#6384) ### 6.6.0.10 20190905 - * Redesign Tuya support by Shantur Rathore removing commands SetOption34, 41, 44, 45, 46 and 65 (#6353) - * Add command Reset 99 to reset bootcount to zero (#684, #6351) - * Change command Time 1/2/3 to select JSON time format ISO, ISO + Epoch or Epoch for legacy reason + +- Redesign Tuya support by Shantur Rathore removing commands SetOption34, 41, 44, 45, 46 and 65 (#6353) +- Add command Reset 99 to reset bootcount to zero (#684, #6351) +- Change command Time 1/2/3 to select JSON time format ISO, ISO + Epoch or Epoch for legacy reason ### 6.6.0.9 20190828 - * Change theoretical baudrate range to 300..19660500 bps in 300 increments (#6294) - * Add Full support of all protocols in IRremoteESP8266, to be used on dedicated-IR Tasmota version. Warning: +81k Flash when compiling with USE_IR_REMOTE_FULL - * Add compile time define USE_WS2812_HARDWARE to select hardware type WS2812, WS2812X, WS2813, SK6812, LC8812 or APA106 (DMA mode only) - * Add 'sonoff-ir' pre-packaged IR-dedicated firmware and 'sonoff-ircustom' to customize firmware with IR Full protocol support - * Add Zigbee support phase 2 - cc2530 initialization and basic ZCL decoding - * Add driver USE_SDM120_2 with Domoticz P1 Smart Meter functionality as future replacement for USE_SDM120 - Pls test and report - * Add command Power0 0/1/2/Off/On/Toggle to control all power outputs at once (#6340) - * Add time to more events (#6337) - * Add command Time 1/2/3 to select JSON time format ISO + Epoch, ISO or Epoch + +- Change theoretical baudrate range to 300..19660500 bps in 300 increments (#6294) +- Add Full support of all protocols in IRremoteESP8266, to be used on dedicated-IR Tasmota version. Warning: +81k Flash when compiling with USE_IR_REMOTE_FULL +- Add compile time define USE_WS2812_HARDWARE to select hardware type WS2812, WS2812X, WS2813, SK6812, LC8812 or APA106 (DMA mode only) +- Add 'sonoff-ir' pre-packaged IR-dedicated firmware and 'sonoff-ircustom' to customize firmware with IR Full protocol support +- Add Zigbee support phase 2 - cc2530 initialization and basic ZCL decoding +- Add driver USE_SDM120_2 with Domoticz P1 Smart Meter functionality as future replacement for USE_SDM120 - Pls test and report +- Add command Power0 0/1/2/Off/On/Toggle to control all power outputs at once (#6340) +- Add time to more events (#6337) +- Add command Time 1/2/3 to select JSON time format ISO + Epoch, ISO or Epoch ### 6.6.0.8 20190827 - * Add Tuya Energy monitoring by Shantur Rathore - * Add phase 1 Domoticz P1 Smart Meter support using energy sensors handled by xdrv_03_energy.ino based on an idea by pablozg - * Add commands Tariff1 0..23 (start Off-Peak hour), Tariff2 0..23 (start Standard hour) and Tariff3 0/1 (Saturday and Sunday Off-Peak) + +- Add Tuya Energy monitoring by Shantur Rathore +- Add phase 1 Domoticz P1 Smart Meter support using energy sensors handled by xdrv_03_energy.ino based on an idea by pablozg +- Add commands Tariff1 0..23 (start Off-Peak hour), Tariff2 0..23 (start Standard hour) and Tariff3 0/1 (Saturday and Sunday Off-Peak) ### 6.6.0.7 20190825 - * Expand Settings area to 4k for future use + +- Expand Settings area to 4k for future use ### 6.6.0.6 20190819 - * Add I2C display driver for SH1106 oled by Gerhard Mutz - * Add SPI display drivers for epaper 4.2 inch, ILI9488 TFT, SSD1351 Color oled and RA8876 TFT by Gerhard Mutz - * Add support for HM17 bluetooth LE passive scan of ibeacon devices by Gerhard Mutz + +- Add I2C display driver for SH1106 oled by Gerhard Mutz +- Add SPI display drivers for epaper 4.2 inch, ILI9488 TFT, SSD1351 Color oled and RA8876 TFT by Gerhard Mutz +- Add support for HM17 bluetooth LE passive scan of ibeacon devices by Gerhard Mutz ### 6.6.0.5 20190816 - * Add command WebSensor 0/1 to control display of sensor data in web GUI (#6085) - * Change some table locations from RAM to Flash - * Fix wrong telemetry message when SetOption68 1 (#6191) - * Add support for RDM6300 125kHz RFID Reader by Gerhard Mutz + +- Add command WebSensor 0/1 to control display of sensor data in web GUI (#6085) +- Change some table locations from RAM to Flash +- Fix wrong telemetry message when SetOption68 1 (#6191) +- Add support for RDM6300 125kHz RFID Reader by Gerhard Mutz ### 6.6.0.4 20190806 - * Add support for CHIRP soil moisture sensor by Christian Baars - * Add debug compile features using defines DEBUG_TASMOTA_CORE, DEBUG_TASMOTA_DRIVER and DEBUG_TASMOTA_SENSOR. - * See DEBUG_CORE_LOG example in sonoff.ino and DEBUG_DRIVER_LOG example in xdrv_09_timers.ino - * Add support for Solax X1 inverter by Pablo Zerón - * Add ZigBee support phase 1 - low level MQTT ZNP messages for CC2530 devices - * Add command Buzzer with optional parameters ,, enabled when a buzzer is configured (#5988) - * Add support for PAJ7620 gesture sensor by Christian Baars + +- Add support for CHIRP soil moisture sensor by Christian Baars +- Add debug compile features using defines DEBUG_TASMOTA_CORE, DEBUG_TASMOTA_DRIVER and DEBUG_TASMOTA_SENSOR. +- See DEBUG_CORE_LOG example in sonoff.ino and DEBUG_DRIVER_LOG example in xdrv_09_timers.ino +- Add support for Solax X1 inverter by Pablo Zerón +- Add ZigBee support phase 1 - low level MQTT ZNP messages for CC2530 devices +- Add command Buzzer with optional parameters ,, enabled when a buzzer is configured (#5988) +- Add support for PAJ7620 gesture sensor by Christian Baars ### 6.6.0.3 20190725 - * Change filename of configuration backup from using FriendlyName1 to Hostname solving diacritic issues (#2422) - * Change Store AWS IoT Private Key and Certificate in SPI Flash avoiding device-specific compilations - * Upgrade library IRRemoteEsp8266 to 2.6.4, now using sendPioneer() - * Add support for MAX31865 Thermocouple sensor by Alberto Lopez Siemens - * Add option 0 to Width1 (Marker), Width2 (Second), Width3 (Minute) and Width4 (Hour) disabling display (#6152) - * Add MqttCount metric to STATE (#6155) - * Add define USE_ENERGY_MARGIN_DETECTION to disable Energy Margin and Power Limit detection - * Add define USE_ENERGY_POWER_LIMIT to disable Energy Power Limit detection while Energy Margin detection is active - * Add allow repeat/longpress for IRSend raw, introduced IRSend option (#6074) - * Add SetOption68 to enable multi-channel PWM instead of a single light (#6134) + +- Change filename of configuration backup from using FriendlyName1 to Hostname solving diacritic issues (#2422) +- Change Store AWS IoT Private Key and Certificate in SPI Flash avoiding device-specific compilations +- Upgrade library IRRemoteEsp8266 to 2.6.4, now using sendPioneer() +- Add support for MAX31865 Thermocouple sensor by Alberto Lopez Siemens +- Add option 0 to Width1 (Marker), Width2 (Second), Width3 (Minute) and Width4 (Hour) disabling display (#6152) +- Add MqttCount metric to STATE (#6155) +- Add define USE_ENERGY_MARGIN_DETECTION to disable Energy Margin and Power Limit detection +- Add define USE_ENERGY_POWER_LIMIT to disable Energy Power Limit detection while Energy Margin detection is active +- Add allow repeat/longpress for IRSend raw, introduced IRSend option (#6074) +- Add SetOption68 to enable multi-channel PWM instead of a single light (#6134) ### 6.6.0.2 20190714 - * Change commands Var and Mem to show all parameters when no index is given (#6107) - * Add command SetOption67 0/1 to disable or enable a buzzer as used in iFan03 - * Add command DisplayWidth to set pixel width on supported devices - * Add command DisplayHeight to set pixel height on supported devices - * Add support for Sonoff iFan03 as module 71 (#5988) - * Add support for a buzzer - * Add support for IRSend long press ('repeat' feature from IRRemoteESP8266) (#6074) - * Add support for IRHVAC Midea/Komeco protocol (#3227) - * Add support for more IRSend protocols enabled in my_user_config.h - * Add support for IRSend Pioneer protocol (#6100) - * Add Oled reset GPIO option "OLED reset" + +- Change commands Var and Mem to show all parameters when no index is given (#6107) +- Add command SetOption67 0/1 to disable or enable a buzzer as used in iFan03 +- Add command DisplayWidth to set pixel width on supported devices +- Add command DisplayHeight to set pixel height on supported devices +- Add support for Sonoff iFan03 as module 71 (#5988) +- Add support for a buzzer +- Add support for IRSend long press ('repeat' feature from IRRemoteESP8266) (#6074) +- Add support for IRHVAC Midea/Komeco protocol (#3227) +- Add support for more IRSend protocols enabled in my_user_config.h +- Add support for IRSend Pioneer protocol (#6100) +- Add Oled reset GPIO option "OLED reset" ### 6.6.0.1 20190708 - * Fix Domoticz battery level set to 100 if define USE_ADC_VCC is not used (#6033) - * Fix Force Elliptic Curve for Letsencrypt TLS #6042 - * Fix WeMo emulation for 1G echo and 2G echo dot (#6086) - * Fix Xiaomi Philips brightness (#6091) - * Change defines USE_TX20_WIND_SENSOR and USE_RC_SWITCH in my_user_config.h to disable to lower iram usage enabling latest core compilation (#6060, #6062) - * Add blend RGB leds with White leds for better whites (#5895, #5704) - * Add command SetOption41 0..8 to control number of Tuya switches (#6039) - * Add command SetOption42 0..255 to set overtemperature (Celsius only) threshold resulting in power off all on energy monitoring devices. Default setting is 90 (#6036) - * Add command SetOption66 0/1 to enable or disable Tuya dimmer range 255 slider control - * Add command Time to disable NTP and set UTC time as Epoch value if above 1451602800 (=20160101). Time 0 re-enables NTP (#5279) - * Add AZ7798 automatic setting of clock display (#6034) - * Add Epoch and UptimeSec to JSON messages (#6068) - * Add support for up to 4 INA219 sensors (#6046) + +- Fix Domoticz battery level set to 100 if define USE_ADC_VCC is not used (#6033) +- Fix Force Elliptic Curve for Letsencrypt TLS #6042 +- Fix WeMo emulation for 1G echo and 2G echo dot (#6086) +- Fix Xiaomi Philips brightness (#6091) +- Change defines USE_TX20_WIND_SENSOR and USE_RC_SWITCH in my_user_config.h to disable to lower iram usage enabling latest core compilation (#6060, #6062) +- Add blend RGB leds with White leds for better whites (#5895, #5704) +- Add command SetOption41 0..8 to control number of Tuya switches (#6039) +- Add command SetOption42 0..255 to set overtemperature (Celsius only) threshold resulting in power off all on energy monitoring devices. Default setting is 90 (#6036) +- Add command SetOption66 0/1 to enable or disable Tuya dimmer range 255 slider control +- Add command Time to disable NTP and set UTC time as Epoch value if above 1451602800 (=20160101). Time 0 re-enables NTP (#5279) +- Add AZ7798 automatic setting of clock display (#6034) +- Add Epoch and UptimeSec to JSON messages (#6068) +- Add support for up to 4 INA219 sensors (#6046) ### 6.6.0 20190707 - * Remove support of TLS on core 2.3.0 and extent support on core 2.4.2 and up - * Remove MQTT uptime message every hour - * Refactor some defines to const - * Refactor webserver HTML input, button, textarea, and select name based on id - * Refactor webserver sensor data collection - * Refactor TLS based on BearSSL, warning breaking change for fingerprints validation - * Refactor management of lights, using classes and integers instead of floats - * Refactor UDP initial message handling from string to char using static memory and add debug info (#5505) - * Refactor IRSend and receive for 64-bit support (#5523) - * Refactor MQTT which might solve issue (#5755) - * Refactor IRSend by using heap when more than 199 values need to be send. May need increase of define MQTT_MAX_PACKET_SIZE too (#5950) - * Refactor double to float in rules, and replaced trigonometric functions from stdlib with smaller versions (#6005) - * Change pubsubclient MQTT_KEEPALIVE from 10 to 30 seconds for AWS IoT support - * Change gamma correction as default behavior, ie "Ledtable 1" - * Change PWM resolution from 8 to 10 bits for low brightness lights - * Change IRSend Panasonic protocol to 64-bit (#5523) - * Change ADC0 to enabled by default in my_user_config.h (#5671) - * Change define USE_EMULATION by USE_EMULATION_HUE and USE_EMULATION_WEMO (#5826) - * Change default PowerDelta from 80% to 0% on new installations (#5858, #5028, #4813, #4130, #4145, #3795, #3778, #3660, #3648) - * Fix display Bug in KNX webmenu for Physical Address - * Fix the Unescape() function and the SendSerial3 behaviour - * Fix webserver multiple Javascript window.onload functionality - * Fix TasmotaSerial at 9600 bps solving DFPlayer comms (#5528) - * Fix Configure Timer Web GUI (#5568) - * Fix Shelly 2.5 I2C address priority issue when VEML6070 code is present by disabling VEML6070 for Shelly 2.5 (#5592) - * Fix use of SerialDelimiter value 128 (#5634) - * Fix Sonoff Pow R2 / S31 invalid energy increments (#5789) - * Fix core 2.5.x ISR not in IRAM exception (#5837) - * Fix Philips Hue emulation Alexa issue by using part of MAC address for LightId (#5849) - * Fix missing white channel for WS2812 (#5869) - * Fix PZem startup issue (#5875) - * Fix exception 9 when syslog is enabled and NTP is just synced (#5917) - * Fix Toggle functionality to button double press when one button and two devices are detected (#5935) - * Fix channel command for dual dimmers (#5940) - * Fix not restoring white value on power off/power on (#5993) - * Add command AdcParam to control ADC0 Temperature and Light formula parameters - * Add command LedMask to assign which relay has access to power LED (#5602, #5612) - * Add extended LED power control using command LedPowerX where X is 1 to 4. Enabled when "LedLink(i)" is configured too (#5709) - * Add command Sensor20 1..255 to change Nova Fitness SDS01 working period in minutes (#5452) - * Add command SetOption38 6..255 to set IRReceive protocol detection sensitivity mimizing UNKNOWN protocols (#5853) - * Add command SetOption39 1..255 to control CSE7766 (Pow R2) or HLW8032 (Blitzwolf SHP5) handling of power loads below 6W. Default setting is 128 (#5756) - * Add command SetOption40 0..250 to disable button functionality if activated for over 0.1 second. Needs SetOption1 1 and SetOption13 0 (#5449) - * Add command SetOption63 0/1 to disable relay state feedback scan at restart (#5594, #5663) - * Add command SetOption64 0/1 to switch between "-" or "_" as sensor index separator impacting DS18X20, DHT, BMP and SHT3X sensor names (#5689) - * Add command SetOption65 0/1 and more Tuya Serial based device support (#5815) - * Add command WebColor to change GUI colors on the fly - * Add support for AWS IoT with TLS 1.2 on core 2.4.2 and up. Full doc here: https://github.com/arendst/Tasmota/wiki/AWS-IoT - * Add support for Badger HR-E Water Meter (#5539) - * Add support for Shelly 2.5 Energy and overtemp Monitoring (#5592) - * Add support for color and colortone for Philips Hue emulation via Alexa (#5600 #4809) - * Add support for Scripts as replacement for Rules. Default disabled but can be enabled in my_user_config.h (#5689) - * Add support for up to four LEDs related to four power outputs. Enabled when "LedLink(i)" is configured too (#5709) - * Add support for Shelly 1PM Template {"NAME":"Shelly 1PM","GPIO":[56,0,0,0,82,134,0,0,0,0,0,21,0],"FLAG":2,"BASE":18} (#5716) - * Add support for SPS30 Particle sensor thanks to Gerhard Mutz (#5830) - * Add support for VL53L0x time of flight sensor. Might interfere with TSL2561 using same I2C address (#5845) - * Add support for Sonoff L1 thanks to reef-actor (#6002) - * Add rule Http#Initialized - * Add rule System#Save executed just before a planned restart - * Add rule support for single JSON value pair like {"SSerialReceived":"on"} by expanding it to {"SSerialReceived":{"Data":"on"}} allowing for trigger SSerialReceived#Data=on (#5638) - * Add define USE_COUNTER to my_user_config.h to save space in sonoff-basic.bin and sonoff-minimal.bin - * Add define USE_DHT to my_user_config.h to save space in sonoff-basic.bin - * Add defines USE_EMULATION_WEMO and USE_EMULATION_HUE to my_user_config.h to control emulation features at compile time (#5826) - * Add Toggle functionality to button double press when more devices are detected - * Add device OverTemp (>73 Celsius) detection to Energy Monitoring devices with temperature sensor powering off all outputs - * Add Tuya Dimmer 10 second heartbeat serial packet required by some Tuya dimmer secondary MCUs - * Add all temperature, humidity and pressure for global access - * Add validation check when loading settings from flash - * Add HX711 weight restore after controlled restart or after power restore just before executing command Sensor34 7 (#5367, #5786) - * Add GUI hexadecimal color options in my_user_config.h (#5586) - * Add alternative IRSend command syntax IRSend raw,,
,
,,,, (#5610) - * Add user configurable ADC0 to Module and Template configuration compatible with current FLAG options (#5671) - * Add AriLux RF control GPIO option "ALux IrSel" (159) replacing "Led4i" (59) for full LED control (#5709) - * Add LED GPIO option "LedLink" (157) and "LedLinki" (158) to select dedicated link status LED (#5709) - * Add all 5 PWM channels individually adressable with LEDs. (#5741) - * Add reset of Energy values when connection to sensor is lost for over 4 seconds (#5874, #5881) - * Add checkbox to GUI password field enabling visibility during password entry only (#5934) + +- Remove support of TLS on core 2.3.0 and extent support on core 2.4.2 and up +- Remove MQTT uptime message every hour +- Refactor some defines to const +- Refactor webserver HTML input, button, textarea, and select name based on id +- Refactor webserver sensor data collection +- Refactor TLS based on BearSSL, warning breaking change for fingerprints validation +- Refactor management of lights, using classes and integers instead of floats +- Refactor UDP initial message handling from string to char using static memory and add debug info (#5505) +- Refactor IRSend and receive for 64-bit support (#5523) +- Refactor MQTT which might solve issue (#5755) +- Refactor IRSend by using heap when more than 199 values need to be send. May need increase of define MQTT_MAX_PACKET_SIZE too (#5950) +- Refactor double to float in rules, and replaced trigonometric functions from stdlib with smaller versions (#6005) +- Change pubsubclient MQTT_KEEPALIVE from 10 to 30 seconds for AWS IoT support +- Change gamma correction as default behavior, ie "Ledtable 1" +- Change PWM resolution from 8 to 10 bits for low brightness lights +- Change IRSend Panasonic protocol to 64-bit (#5523) +- Change ADC0 to enabled by default in my_user_config.h (#5671) +- Change define USE_EMULATION by USE_EMULATION_HUE and USE_EMULATION_WEMO (#5826) +- Change default PowerDelta from 80% to 0% on new installations (#5858, #5028, #4813, #4130, #4145, #3795, #3778, #3660, #3648) +- Fix display Bug in KNX webmenu for Physical Address +- Fix the Unescape() function and the SendSerial3 behaviour +- Fix webserver multiple Javascript window.onload functionality +- Fix TasmotaSerial at 9600 bps solving DFPlayer comms (#5528) +- Fix Configure Timer Web GUI (#5568) +- Fix Shelly 2.5 I2C address priority issue when VEML6070 code is present by disabling VEML6070 for Shelly 2.5 (#5592) +- Fix use of SerialDelimiter value 128 (#5634) +- Fix Sonoff Pow R2 / S31 invalid energy increments (#5789) +- Fix core 2.5.x ISR not in IRAM exception (#5837) +- Fix Philips Hue emulation Alexa issue by using part of MAC address for LightId (#5849) +- Fix missing white channel for WS2812 (#5869) +- Fix PZem startup issue (#5875) +- Fix exception 9 when syslog is enabled and NTP is just synced (#5917) +- Fix Toggle functionality to button double press when one button and two devices are detected (#5935) +- Fix channel command for dual dimmers (#5940) +- Fix not restoring white value on power off/power on (#5993) +- Add command AdcParam to control ADC0 Temperature and Light formula parameters +- Add command LedMask to assign which relay has access to power LED (#5602, #5612) +- Add extended LED power control using command LedPowerX where X is 1 to 4. Enabled when "LedLink(i)" is configured too (#5709) +- Add command Sensor20 1..255 to change Nova Fitness SDS01 working period in minutes (#5452) +- Add command SetOption38 6..255 to set IRReceive protocol detection sensitivity mimizing UNKNOWN protocols (#5853) +- Add command SetOption39 1..255 to control CSE7766 (Pow R2) or HLW8032 (Blitzwolf SHP5) handling of power loads below 6W. Default setting is 128 (#5756) +- Add command SetOption40 0..250 to disable button functionality if activated for over 0.1 second. Needs SetOption1 1 and SetOption13 0 (#5449) +- Add command SetOption63 0/1 to disable relay state feedback scan at restart (#5594, #5663) +- Add command SetOption64 0/1 to switch between "-" or "_" as sensor index separator impacting DS18X20, DHT, BMP and SHT3X sensor names (#5689) +- Add command SetOption65 0/1 and more Tuya Serial based device support (#5815) +- Add command WebColor to change GUI colors on the fly +- Add support for AWS IoT with TLS 1.2 on core 2.4.2 and up. Full doc here: https://github.com/arendst/Tasmota/wiki/AWS-IoT +- Add support for Badger HR-E Water Meter (#5539) +- Add support for Shelly 2.5 Energy and overtemp Monitoring (#5592) +- Add support for color and colortone for Philips Hue emulation via Alexa (#5600 #4809) +- Add support for Scripts as replacement for Rules. Default disabled but can be enabled in my_user_config.h (#5689) +- Add support for up to four LEDs related to four power outputs. Enabled when "LedLink(i)" is configured too (#5709) +- Add support for Shelly 1PM Template {"NAME":"Shelly 1PM","GPIO":[56,0,0,0,82,134,0,0,0,0,0,21,0],"FLAG":2,"BASE":18} (#5716) +- Add support for SPS30 Particle sensor thanks to Gerhard Mutz (#5830) +- Add support for VL53L0x time of flight sensor. Might interfere with TSL2561 using same I2C address (#5845) +- Add support for Sonoff L1 thanks to reef-actor (#6002) +- Add rule Http#Initialized +- Add rule System#Save executed just before a planned restart +- Add rule support for single JSON value pair like {"SSerialReceived":"on"} by expanding it to {"SSerialReceived":{"Data":"on"}} allowing for trigger SSerialReceived#Data=on (#5638) +- Add define USE_COUNTER to my_user_config.h to save space in sonoff-basic.bin and sonoff-minimal.bin +- Add define USE_DHT to my_user_config.h to save space in sonoff-basic.bin +- Add defines USE_EMULATION_WEMO and USE_EMULATION_HUE to my_user_config.h to control emulation features at compile time (#5826) +- Add Toggle functionality to button double press when more devices are detected +- Add device OverTemp (>73 Celsius) detection to Energy Monitoring devices with temperature sensor powering off all outputs +- Add Tuya Dimmer 10 second heartbeat serial packet required by some Tuya dimmer secondary MCUs +- Add all temperature, humidity and pressure for global access +- Add validation check when loading settings from flash +- Add HX711 weight restore after controlled restart or after power restore just before executing command Sensor34 7 (#5367, #5786) +- Add GUI hexadecimal color options in my_user_config.h (#5586) +- Add alternative IRSend command syntax IRSend raw,,
,
,,,, (#5610) +- Add user configurable ADC0 to Module and Template configuration compatible with current FLAG options (#5671) +- Add AriLux RF control GPIO option "ALux IrSel" (159) replacing "Led4i" (59) for full LED control (#5709) +- Add LED GPIO option "LedLink" (157) and "LedLinki" (158) to select dedicated link status LED (#5709) +- Add all 5 PWM channels individually adressable with LEDs. (#5741) +- Add reset of Energy values when connection to sensor is lost for over 4 seconds (#5874, #5881) +- Add checkbox to GUI password field enabling visibility during password entry only (#5934) ### 6.5.0 20190319 - * Remove commands SetOption14 and SetOption63 as it has been superseded by command Interlock - * Remove command SetOption35 0-255 for mDNS start-up delay (#4793) - * Remove support for MQTT_LIBRARY_TYPE, MQTT_ARDUINOMQTT and MQTT_TASMOTAMQTT (#5474) - * Change webserver content handling from single String to small Chunks increasing RAM - * Change code use of boolean to bool and byte to uint8_t - * Change code uint8_t flags to bool flags - * Change sonoff_template.h layout regarding optional module flags like ADC0 - * Change sonoff_template.h module lay-out by removing non-configurable GPIOs - * Change button driver making it modular - * Change switch driver making it modular and introduce input filter (#4665, #4724) - * Change switch input detection by optimizing switch debounce (#4724) - * Change web authentication (#4865) - * Change image name BE_MINIMAL to FIRMWARE_MINIMAL and USE_xyz to FIRMWARE_xyz (#5106) - * Change GUI weblog from XML to plain text solving possible empty screens (#5154) - * Fix most compiler warnings - * Fix Display exception 28 when JSON value is nullptr received - * Fix epaper driver (#4785) - * Fix HAss Sensor Discovery Software Watchdog restart (#4831, #4988) - * Fix allowable MAX_RULE_VARS to 16 (#4933) - * Fix mDNS addService (#4938, #4951) - * Fix HAss discovery of MHZ19(B) sensors (#4992) - * Fix some exceptions and watchdogs due to lack of stack space (#5215) - * Fix GUI wifi password acception starting with asteriks (*) (#5231, #5242) - * Fix command WebSend intermittent results (#5273, #5304) - * Fix additional characters in fallbacktopic, hostname and mqttclient on core 2.5.0 (#5359, #5417) - * Fix Energy TotalStartTime when commands EnergyReset0 and/or EnergyReset3 used (#5373) - * Fix DS18S20 temperature calculation (#5375) - * Fix float calculations in range from 0 to -1 (#5386) - * Fix exception on GUI Configure Logging and Configure Other (#5424) - * Add commands PowerCal, VoltageCal and CurrentCal for HLW8012, HJL01 and BL0937 based energy sensors - * Add command SerialDelimiter 128 to filter reception of only characters between ASCII 32 and 127 (#5131) - * Add command SSerialSend5 \ to SerialBridge - * Add command Interlock 0 / 1 / 1,2 3,4 .. to control interlock ON/OFF and add up to 8 relays in 1 to 4 interlock groups (#4910, #5014) - * Add command Template 255 to copy module configuration over to current active template and store as user template named Merged (#5371) - * Add command WifiConfig 7 to allow reset of device in AP mode without admin password (#5297) - * Add command SetOption36 to control boot loop default restoration (#4645, #5063) - * Add command SetOption37 for RGBCW color mapping (#5326) - * Add command SetOption55 0/1 and define MDNS_ENABLE to disable/enable mDNS (#4793, #4923) - * Add command SetOption62 0/1 to disable retain on Button or Switch hold messages (#5299) - * Add support for Smanergy KA10 Smart Wall Socket with Energy monitoring - * Add support for commands in sensor drivers - * Add support for MAX31855 K-Type thermocouple sensor using softSPI (#4764) - * Add support for Near Field Communication (NFC) controller PN532 using Serial (#4791, #5162) - * Add support for OBI Power Socket 2 (#4829) - * Add support for YTF IR Bridge (#4855) - * Add support for Mi LED Desk Lamp with rotary switch (#4887) - * Add support for Digoo DG-SP202 Smart Socket with Energy monitoring (#4891) - * Add support for MAX44009 Ambient Light sensor (#4907) - * Add support for inverted buttons and inverted buttons without pullup (#4914) - * Add support for Luminea ZX2820 Smart Socket with Energy monitoring (#4921) - * Add support for multiple ADS1115 I2C devices (#5083) - * Add support for online template change using command Template or GUI Configure Other (#5177) - * Add support for Korean language translations (#5344) - * Add support for sensor SCD30 (#5434) - * Add parameter CFG_HOLDER to status 1 message (#5206) - * Add SetOption32 until SetOption49 diagnostic information to Status 3 report as replacement for second property value in SetOption property name - * Add Resolution property to Status 3 report providing previous SetOption second value property - * Add property MqttCount to status 6 message representing number of Mqtt re-connections - * Add property LinkCount to state and status 11 message representing number of Wifi Link re-connections - * Add property Downtime to state and status 11 message representing the duration of wifi connection loss - * Add variable %timestamp% to rules (#4749) - * Add rule support for "==", "!=" ">=" and "<=" (#5122) - * Add rule expression enabled by define USE_EXPRESSION in my_user_config.h (#5210) - * Add Power status functionality to LED2 when configured leaving LED1 for Link status indication - * Add user configuration of HLW8012 and HJL-01/BL0937 Energy Monitoring as used in Sonoff Pow and many Tuya based devices - * Add user configuration of MCP39F501 Energy Monitoring as used in Shelly2 - * Add online template configuration using both commands and Configure Template menu option in GUI - * Add (S)SerialSend3 escape sequence \x to allow hexadecimal byte value (#3560, #4947) - * Add define DS18B20_INTERNAL_PULLUP to select internal input pullup when only one DS18B20 sensor is connected eliminating external resistor (#4738) - * Add button control when no relay configured (#4682) - * Add startup delay of 4 seconds to button control (#4829) - * Add core version conditional compile options to provided PWM files (#4917) - * Add resiliency to saved Settings (#5065) - * Add MHZ19 Temperature as Domoticz Temperature selection (#5128) - * Add HAss status sensor (#5139) - * Add status message to former declined group commands (#5145) - * Add 0x to IRRemote (SetOption29) and RCSwitch (SetOption28) received hexadecimal data (#5431) +- Remove commands SetOption14 and SetOption63 as it has been superseded by command Interlock +- Remove command SetOption35 0-255 for mDNS start-up delay (#4793) +- Remove support for MQTT_LIBRARY_TYPE, MQTT_ARDUINOMQTT and MQTT_TASMOTAMQTT (#5474) +- Change webserver content handling from single String to small Chunks increasing RAM +- Change code use of boolean to bool and byte to uint8_t +- Change code uint8_t flags to bool flags +- Change sonoff_template.h layout regarding optional module flags like ADC0 +- Change sonoff_template.h module lay-out by removing non-configurable GPIOs +- Change button driver making it modular +- Change switch driver making it modular and introduce input filter (#4665, #4724) +- Change switch input detection by optimizing switch debounce (#4724) +- Change web authentication (#4865) +- Change image name BE_MINIMAL to FIRMWARE_MINIMAL and USE_xyz to FIRMWARE_xyz (#5106) +- Change GUI weblog from XML to plain text solving possible empty screens (#5154) +- Fix most compiler warnings +- Fix Display exception 28 when JSON value is nullptr received +- Fix epaper driver (#4785) +- Fix HAss Sensor Discovery Software Watchdog restart (#4831, #4988) +- Fix allowable MAX_RULE_VARS to 16 (#4933) +- Fix mDNS addService (#4938, #4951) +- Fix HAss discovery of MHZ19(B) sensors (#4992) +- Fix some exceptions and watchdogs due to lack of stack space (#5215) +- Fix GUI wifi password acception starting with asteriks (*) (#5231, #5242) +- Fix command WebSend intermittent results (#5273, #5304) +- Fix additional characters in fallbacktopic, hostname and mqttclient on core 2.5.0 (#5359, #5417) +- Fix Energy TotalStartTime when commands EnergyReset0 and/or EnergyReset3 used (#5373) +- Fix DS18S20 temperature calculation (#5375) +- Fix float calculations in range from 0 to -1 (#5386) +- Fix exception on GUI Configure Logging and Configure Other (#5424) +- Add commands PowerCal, VoltageCal and CurrentCal for HLW8012, HJL01 and BL0937 based energy sensors +- Add command SerialDelimiter 128 to filter reception of only characters between ASCII 32 and 127 (#5131) +- Add command SSerialSend5 \ to SerialBridge +- Add command Interlock 0 / 1 / 1,2 3,4 .. to control interlock ON/OFF and add up to 8 relays in 1 to 4 interlock groups (#4910, #5014) +- Add command Template 255 to copy module configuration over to current active template and store as user template named Merged (#5371) +- Add command WifiConfig 7 to allow reset of device in AP mode without admin password (#5297) +- Add command SetOption36 to control boot loop default restoration (#4645, #5063) +- Add command SetOption37 for RGBCW color mapping (#5326) +- Add command SetOption55 0/1 and define MDNS_ENABLE to disable/enable mDNS (#4793, #4923) +- Add command SetOption62 0/1 to disable retain on Button or Switch hold messages (#5299) +- Add support for Smanergy KA10 Smart Wall Socket with Energy monitoring +- Add support for commands in sensor drivers +- Add support for MAX31855 K-Type thermocouple sensor using softSPI (#4764) +- Add support for Near Field Communication (NFC) controller PN532 using Serial (#4791, #5162) +- Add support for OBI Power Socket 2 (#4829) +- Add support for YTF IR Bridge (#4855) +- Add support for Mi LED Desk Lamp with rotary switch (#4887) +- Add support for Digoo DG-SP202 Smart Socket with Energy monitoring (#4891) +- Add support for MAX44009 Ambient Light sensor (#4907) +- Add support for inverted buttons and inverted buttons without pullup (#4914) +- Add support for Luminea ZX2820 Smart Socket with Energy monitoring (#4921) +- Add support for multiple ADS1115 I2C devices (#5083) +- Add support for online template change using command Template or GUI Configure Other (#5177) +- Add support for Korean language translations (#5344) +- Add support for sensor SCD30 (#5434) +- Add parameter CFG_HOLDER to status 1 message (#5206) +- Add SetOption32 until SetOption49 diagnostic information to Status 3 report as replacement for second property value in SetOption property name +- Add Resolution property to Status 3 report providing previous SetOption second value property +- Add property MqttCount to status 6 message representing number of Mqtt re-connections +- Add property LinkCount to state and status 11 message representing number of Wifi Link re-connections +- Add property Downtime to state and status 11 message representing the duration of wifi connection loss +- Add variable %timestamp% to rules (#4749) +- Add rule support for "==", "!=" ">=" and "<=" (#5122) +- Add rule expression enabled by define USE_EXPRESSION in my_user_config.h (#5210) +- Add Power status functionality to LED2 when configured leaving LED1 for Link status indication +- Add user configuration of HLW8012 and HJL-01/BL0937 Energy Monitoring as used in Sonoff Pow and many Tuya based devices +- Add user configuration of MCP39F501 Energy Monitoring as used in Shelly2 +- Add online template configuration using both commands and Configure Template menu option in GUI +- Add (S)SerialSend3 escape sequence \x to allow hexadecimal byte value (#3560, #4947) +- Add define DS18B20_INTERNAL_PULLUP to select internal input pullup when only one DS18B20 sensor is connected eliminating external resistor (#4738) +- Add button control when no relay configured (#4682) +- Add startup delay of 4 seconds to button control (#4829) +- Add core version conditional compile options to provided PWM files (#4917) +- Add resiliency to saved Settings (#5065) +- Add MHZ19 Temperature as Domoticz Temperature selection (#5128) +- Add HAss status sensor (#5139) +- Add status message to former declined group commands (#5145) +- Add 0x to IRRemote (SetOption29) and RCSwitch (SetOption28) received hexadecimal data (#5431) ### 6.4.1 20181224 - * Change RAM usage BMP/BME I2C sensors - * Change FallbackTopic from cmnd// to cmnd/_fb/ to discriminate from Topic (#1528) - * Change FallbackTopic detection (#4706) - * Change Hass discovery to short MQTT messages as used by Hass 0.81 and up (#4711) - * Change MQTT GUI password handling (#4723) - * Fix possible dtostrf buffer overflows by increasing buffers - * Fix wifi strongest signal detection (#4704) - * Fix Alexa "this value is outside the range of the device". Needs power cycle and Alexa deletion/discovery cycle. (#3159, #4712) - * Add Slovak language file (#4663) - * Add support for AZ-Instrument 7798 CO2 meter/datalogger (#4672) - * Add define WIFI_SOFT_AP_CHANNEL in my_user_config.h to set Soft Access Point Channel number between 1 and 13 as used by Wifi Manager web GUI (#4673) - * Add define USE_MQTT_TLS_CA_CERT for checking MQTT TLS against root ca using Let's Encrypt cert from sonoff_letsencrypt.h - not supported with core 2.3.0 (#4703) +- Change RAM usage BMP/BME I2C sensors +- Change FallbackTopic from cmnd// to cmnd/_fb/ to discriminate from Topic (#1528) +- Change FallbackTopic detection (#4706) +- Change Hass discovery to short MQTT messages as used by Hass 0.81 and up (#4711) +- Change MQTT GUI password handling (#4723) +- Fix possible dtostrf buffer overflows by increasing buffers +- Fix wifi strongest signal detection (#4704) +- Fix Alexa "this value is outside the range of the device". Needs power cycle and Alexa deletion/discovery cycle. (#3159, #4712) +- Add Slovak language file (#4663) +- Add support for AZ-Instrument 7798 CO2 meter/datalogger (#4672) +- Add define WIFI_SOFT_AP_CHANNEL in my_user_config.h to set Soft Access Point Channel number between 1 and 13 as used by Wifi Manager web GUI (#4673) +- Add define USE_MQTT_TLS_CA_CERT for checking MQTT TLS against root ca using Let's Encrypt cert from sonoff_letsencrypt.h - not supported with core 2.3.0 (#4703) ### 6.4.0 20181217 - * Change GUI Configure Module by using AJAX for data fetch to cut page size (and memory use) by 40% +- Change GUI Configure Module by using AJAX for data fetch to cut page size (and memory use) by 40% In case of web page errors clear your browser cache or do Page Reload (F5 or Ctrl+R) - * Change enforcing flashmode dout but it is still mandatory - * Change bootcount update (being first) flash write to 10 seconds after restart - * Change display and epaper drivers - * Change command WebSend Host header field from IP address to hostname (#4331) - * Change log buffer size from 512 to 520 to accommodate http sensor data (#4354) - * Change default WIFI_CONFIG_TOOL from WIFI_WAIT to WIFI_RETRY in my_user_config.h (#4400) - * Change webgui refresh time delay for Save Settings and local OTA Upload (#4423) - * Change SR-04 driver to use NewPing library (#4488) - * Change MCP230xx driver to support interrupt retention over teleperiod (#4547) - * Change support for MPU6050 using DMP (#4581) - * Fix unintended function overload of WifiState - * Fix wifi connection errors using wifi disconnect and ESP.reset instead of ESP.restart - * Fix Sonoff Pow R2 and Sonoff S31 Serial interface hang caused by Sonoff Basic R2 driver delay implementation (and possibly core bug) - * Fix MQTT connection error after restart - * Fix wifi re-scan connection baseline - * Fix possible strncat buffer overflows - * Fix intermittent Pzem sensor energy overflow calculation error - * Fix shelly2 ghost switching caused by lack of pull-up inputs (#4255) - * Fix hardware serial pin configuration. To keep using hardware serial swap current Rx/Tx pin configuration only (#4280) - * Fix MqttRetry values above 255 seconds (#4424) - * Fix WifiManager functionality on initial installation (#4433) - * Fix ArduinoOTA for Core 2.5.0 (#4620) - * Add minutes to commands Timezone to allow all possible world timezones - * Add more strict checks for GPIO selections - * Add code image and optional commit number to version - * Add dynamic delay to main loop providing time for wifi background tasks - * Add additional start-up delay during initial wifi connection - * Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver - * Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver - * Add user definition of defines WIFI_RSSI_THRESHOLD (default 10) and WIFI_RESCAN_MINUTES (default 44) - * Add command SetOption58 0/1 to enable IR raw data info in JSON message (#2116) - * Add command IRSend |0,,,.. to allow raw data transmission (#2116) - * Add command SetOption56 0/1 to enable wifi network scan and select highest RSSI (#3173) - * Add command SetOption57 0/1 to enable wifi network re-scan every 44 minutes with a rssi threshold of 10 to select highest RSSI (#3173) - * Add support for SDM220 (#3610) - * Add default sleep 1 to sonoff-basic to lower energy consumption (#4217) - * Add wifi status to Tuya (#4221) - * Add delays to reduce CPU usage at boot time (#4233) - * Add command SetOption24 0/1 to select pressure unit as hPa or mmHg (#4241) - * Add optional hardware serial when GPIO13(Rx) and GPIO15(Tx) are selected removing hardware serial from GPIO01(Tx) and GPIO03(Rx) (#4288) - * Add support for Gosund SP1 v2.3 Power Socket with Energy Monitoring (#4297) - * Add support for Armtronix dimmers. See wiki for info (#4321) - * Add to command WebSend option to send a direct path when command starts with a slash (#4329) - * Add support for LG HVac and IrRemote (#4377) - * Add initial support for Hass sensor discovery (#4380) - * Add support for Fujitsu HVac and IrRemote (#4387) - * Add support for I2C MGC3130 Electric Field Effect sensor by Christian Baars (#3774, #4404) - * Add command CalcRes to set number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE (#4420) - * Add CPU average load to state message (#4431) - * Add command SetOption59 0/1 to change state topic from tele/STATE to stat/RESULT (#4450) - * Add support for SM Smart Wifi Dimmer PS-16-DZ (#4465) - * Add support for Teckin US Power Socket with Energy Monitoring (#4481) - * Add command SetOption60 0/1 to select dynamic sleep (0) or sleep (1) (#4497) - * Add support for iFan02 Fanspeed in Domoticz using a selector (#4517) - * Add support for GPIO02 for newer Sonoff Basic (#4518) - * Add Announce Switches to MQTT Discovery (#4531) - * Add support for Manzoku Power Strip (#4590) +- Change enforcing flashmode dout but it is still mandatory +- Change bootcount update (being first) flash write to 10 seconds after restart +- Change display and epaper drivers +- Change command WebSend Host header field from IP address to hostname (#4331) +- Change log buffer size from 512 to 520 to accommodate http sensor data (#4354) +- Change default WIFI_CONFIG_TOOL from WIFI_WAIT to WIFI_RETRY in my_user_config.h (#4400) +- Change webgui refresh time delay for Save Settings and local OTA Upload (#4423) +- Change SR-04 driver to use NewPing library (#4488) +- Change MCP230xx driver to support interrupt retention over teleperiod (#4547) +- Change support for MPU6050 using DMP (#4581) +- Fix unintended function overload of WifiState +- Fix wifi connection errors using wifi disconnect and ESP.reset instead of ESP.restart +- Fix Sonoff Pow R2 and Sonoff S31 Serial interface hang caused by Sonoff Basic R2 driver delay implementation (and possibly core bug) +- Fix MQTT connection error after restart +- Fix wifi re-scan connection baseline +- Fix possible strncat buffer overflows +- Fix intermittent Pzem sensor energy overflow calculation error +- Fix shelly2 ghost switching caused by lack of pull-up inputs (#4255) +- Fix hardware serial pin configuration. To keep using hardware serial swap current Rx/Tx pin configuration only (#4280) +- Fix MqttRetry values above 255 seconds (#4424) +- Fix WifiManager functionality on initial installation (#4433) +- Fix ArduinoOTA for Core 2.5.0 (#4620) +- Add minutes to commands Timezone to allow all possible world timezones +- Add more strict checks for GPIO selections +- Add code image and optional commit number to version +- Add dynamic delay to main loop providing time for wifi background tasks +- Add additional start-up delay during initial wifi connection +- Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver +- Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver +- Add user definition of defines WIFI_RSSI_THRESHOLD (default 10) and WIFI_RESCAN_MINUTES (default 44) +- Add command SetOption58 0/1 to enable IR raw data info in JSON message (#2116) +- Add command IRSend |0,,,.. to allow raw data transmission (#2116) +- Add command SetOption56 0/1 to enable wifi network scan and select highest RSSI (#3173) +- Add command SetOption57 0/1 to enable wifi network re-scan every 44 minutes with a rssi threshold of 10 to select highest RSSI (#3173) +- Add support for SDM220 (#3610) +- Add default sleep 1 to sonoff-basic to lower energy consumption (#4217) +- Add wifi status to Tuya (#4221) +- Add delays to reduce CPU usage at boot time (#4233) +- Add command SetOption24 0/1 to select pressure unit as hPa or mmHg (#4241) +- Add optional hardware serial when GPIO13(Rx) and GPIO15(Tx) are selected removing hardware serial from GPIO01(Tx) and GPIO03(Rx) (#4288) +- Add support for Gosund SP1 v2.3 Power Socket with Energy Monitoring (#4297) +- Add support for Armtronix dimmers. See wiki for info (#4321) +- Add to command WebSend option to send a direct path when command starts with a slash (#4329) +- Add support for LG HVac and IrRemote (#4377) +- Add initial support for Hass sensor discovery (#4380) +- Add support for Fujitsu HVac and IrRemote (#4387) +- Add support for I2C MGC3130 Electric Field Effect sensor by Christian Baars (#3774, #4404) +- Add command CalcRes to set number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE (#4420) +- Add CPU average load to state message (#4431) +- Add command SetOption59 0/1 to change state topic from tele/STATE to stat/RESULT (#4450) +- Add support for SM Smart Wifi Dimmer PS-16-DZ (#4465) +- Add support for Teckin US Power Socket with Energy Monitoring (#4481) +- Add command SetOption60 0/1 to select dynamic sleep (0) or sleep (1) (#4497) +- Add support for iFan02 Fanspeed in Domoticz using a selector (#4517) +- Add support for GPIO02 for newer Sonoff Basic (#4518) +- Add Announce Switches to MQTT Discovery (#4531) +- Add support for Manzoku Power Strip (#4590) ### 6.3.0 20181030 - * Change web Configure Module GPIO drop down list order for better readability - * Change status JSON message providing more switch and retain information - * Change xsns_17_senseair.ino to use TasmotaModbus library - * Change MCP230xx driver - * Change PubSubClient Mqtt library to non-blocking EspEasy version - * Change energy monitoring using energy sensor driver modules - * Change Webserver page handler for easier extension (thx to Adrian Scillato) - * Change pinmode for no-pullup defined switches to pullup when configured as switchmode PUSHBUTTON (=3 and up) (#3896) - * Change default OTA Url to http://thehackbox.org/tasmota/release/sonoff.bin (#4170) - * Remove support for MQTT Client esp-mqtt-arduino by #define MQTT_LIBRARY_TYPE MQTT_ESPMQTTARDUINO - * Remove commands PowerCal, VoltageCal and CurrentCal as more functionality is provided by commands PowerSet, VoltageSet and CurrentSet - * Remove restart after ntpserver change and force NTP re-sync (#3890) - * Fix showing Period Power in energy threshold messages - * Fix header file execution order by renaming user_config.h to my_user_config.h - * Fix some TSL2561 driver issues (#3681) - * Fix KNX PA exception. Regression from 6.2.1 buffer overflow caused by subStr() (#3700, #3710) - * Fix setting and getting color temperature for Philips Hue emulation (#3733) - * Fix ButtonRetain to not use default topic for clearing retain messages (#3737) - * Fix syslog when emulation is selected (#2109, #3784) - * Fix rule trigger POWER1#STATE execution after restart and SetOption0 is 0 (#3856) - * Fix Home Assistant forced light discovery (#3908) - * Fix invalid configuration restores and decode_config.py crc error when savedata = 0 (#3918) - * Fix timer offset -00:00 causing 12:00 hour offset (#3923) - * Fix I2CScan invalid JSON error message (#3925) - * Fix exception when wrong Domoticz JSON message is received (#3963) - * Fix Sonoff Bridge RfRaw receive (#4080, #4085) - * Fix possible wifi connection error (#4044, #4083) - * Fix invalid JSON floating point result from nan (Not a Number) and inf (Infinity) into null (#4147) - * Fix rule mqtt#connected trigger when mqtt is disabled (#4149) - * Add support for LCD, Matrix, TFT and Oled displays - * Add support for Neo Coolcam Wifi Smart Power Plug - * Add support for Michael Haustein ESP Switch - * Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT - * Add support for Neo Coolcam Wifi Smart Power Plug - * Add support for Michael Haustein ESP Switch - * Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT - * Add support for DS3231 Real Time Clock - * Add support for HX711 Load Cell with optional web GUI scale interface to demonstrate easy GUI plug-in - * Add support for serial 8N2 communication to TasmotaModbus and TasmotaSerial libraries - * Add support for RF transceiving using library RcSwitch (#2702) - * Add support for Shelly 1 and Shelly 2 (#2789) - * Add support for La Crosse TX20 Anemometer (#2654, #3146) - * Add support for MP3 player using DFRobot RB-DFR-562 (#3723) - * Add Support for Xiaomi-Philips Bulbs (#3787) - * Add support for PCA9685 12bit 16pin hardware PWM driver (#3866) - * Add support for EXS Relay V5.0 (#3810) - * Add support for OBI Power Socket (#1988, #3944) - * Add support for Teckin Power Socket with Energy Monitoring (#3950) - * Add support for Pzem-003/017 DC Energy monitoring module (#3694) - * Add support for Pzem-014/016 AC Energy monitoring module (#3694) - * Add support for CSL Aplic WDP 303075 Power Socket with Energy Monitoring (#3991, #3996) - * Add support for Tuya Dimmer (#469, #4075) - * Add command Display to show all settings at once - * Add command SerialSend5 to send raw serial data like "A5074100545293" - * Add command WebRefresh 1000..10000 to control web page refresh in milliseconds. Default is 2345 - * Add command WeightRes 0..3 to control display of decimals for kilogram - * Add command RGBWWTable to support color calibration (#3933) - * Add command Reset 4 (reset to defaults but keep wifi params) and Reset 5 (as reset 4 and also erase flash) (#4061) - * Add command SetOption35 0..255 (seconds) to delay mDNS initialization to control possible Wifi connect problems - * Add command SetOption52 0/1 to control display of optional time offset from UTC in JSON messages (#3629, #3711) - * Add command SetOption53 0/1 to toggle gui display of Hostname and IP address (#1006, #2091) - * Add authentication to HTTP web pages - * Add decimals as input to commands PowerSet, VoltageSet and CurrentSet - * Add tools/decode-config.py by Norbert Richter to decode configuration data. See file for information - * Add define USE_DISPLAYS for selecting image sonoff-display - * Add define USE_BASIC for selecting image sonoff-basic without most sensors - * Add auto reload of main web page to some web restarts - * Add TasmotaModbus library as very basic modbus wrapper for TasmotaSerial - * Add more API callbacks and document API.md - * Add Apparent Power and Reactive Power to Energy Monitoring devices (#251) - * Add token %hostname% to command FullTopic (#3018) - * Add Wifi channel number to state message (#3664) - * Add user configurable GPIO02 and GPIO03 on H801 devices (#3692) - * Add toggle function RGBW lights (#3695, #3697) - * Add network information to display start screen (#3704) - * Add sleep to Nova Fitness SDS01X sensor (#2841, #3724, #3749) - * Add Analog input AD0 enabled to sonoff-sensors.bin (#3756, #3757) - * Add power value below 5W to Sonoff Pow R2 and S31 (#3745) - * Add RF Receiver control to module MagicHome to be used on Arilux LC10 (#3792) - * Add userid/password option to decode-status.py (#3796) - * Add delay after restart before processing rule sensor data (#3811) - * Add force_update to Home Assistant discovery (#3873) - * Add rule triggers SWITCH1#BOOT and POWER1#BOOT (#3904, #3910) - * Add Hebrew language file (#3960) - * Add TotalStartTime to Energy JSON message (#3971) - * Add whitespace removal from RfRaw and SerialSend5 (#4020) - * Add support for two BMP/BME sensors (#4195) +- Change web Configure Module GPIO drop down list order for better readability +- Change status JSON message providing more switch and retain information +- Change xsns_17_senseair.ino to use TasmotaModbus library +- Change MCP230xx driver +- Change PubSubClient Mqtt library to non-blocking EspEasy version +- Change energy monitoring using energy sensor driver modules +- Change Webserver page handler for easier extension (thx to Adrian Scillato) +- Change pinmode for no-pullup defined switches to pullup when configured as switchmode PUSHBUTTON (=3 and up) (#3896) +- Change default OTA Url to http://thehackbox.org/tasmota/release/sonoff.bin (#4170) +- Remove support for MQTT Client esp-mqtt-arduino by #define MQTT_LIBRARY_TYPE MQTT_ESPMQTTARDUINO +- Remove commands PowerCal, VoltageCal and CurrentCal as more functionality is provided by commands PowerSet, VoltageSet and CurrentSet +- Remove restart after ntpserver change and force NTP re-sync (#3890) +- Fix showing Period Power in energy threshold messages +- Fix header file execution order by renaming user_config.h to my_user_config.h +- Fix some TSL2561 driver issues (#3681) +- Fix KNX PA exception. Regression from 6.2.1 buffer overflow caused by subStr() (#3700, #3710) +- Fix setting and getting color temperature for Philips Hue emulation (#3733) +- Fix ButtonRetain to not use default topic for clearing retain messages (#3737) +- Fix syslog when emulation is selected (#2109, #3784) +- Fix rule trigger POWER1#STATE execution after restart and SetOption0 is 0 (#3856) +- Fix Home Assistant forced light discovery (#3908) +- Fix invalid configuration restores and decode_config.py crc error when savedata = 0 (#3918) +- Fix timer offset -00:00 causing 12:00 hour offset (#3923) +- Fix I2CScan invalid JSON error message (#3925) +- Fix exception when wrong Domoticz JSON message is received (#3963) +- Fix Sonoff Bridge RfRaw receive (#4080, #4085) +- Fix possible wifi connection error (#4044, #4083) +- Fix invalid JSON floating point result from nan (Not a Number) and inf (Infinity) into null (#4147) +- Fix rule mqtt#connected trigger when mqtt is disabled (#4149) +- Add support for LCD, Matrix, TFT and Oled displays +- Add support for Neo Coolcam Wifi Smart Power Plug +- Add support for Michael Haustein ESP Switch +- Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT +- Add support for Neo Coolcam Wifi Smart Power Plug +- Add support for Michael Haustein ESP Switch +- Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT +- Add support for DS3231 Real Time Clock +- Add support for HX711 Load Cell with optional web GUI scale interface to demonstrate easy GUI plug-in +- Add support for serial 8N2 communication to TasmotaModbus and TasmotaSerial libraries +- Add support for RF transceiving using library RcSwitch (#2702) +- Add support for Shelly 1 and Shelly 2 (#2789) +- Add support for La Crosse TX20 Anemometer (#2654, #3146) +- Add support for MP3 player using DFRobot RB-DFR-562 (#3723) +- Add Support for Xiaomi-Philips Bulbs (#3787) +- Add support for PCA9685 12bit 16pin hardware PWM driver (#3866) +- Add support for EXS Relay V5.0 (#3810) +- Add support for OBI Power Socket (#1988, #3944) +- Add support for Teckin Power Socket with Energy Monitoring (#3950) +- Add support for Pzem-003/017 DC Energy monitoring module (#3694) +- Add support for Pzem-014/016 AC Energy monitoring module (#3694) +- Add support for CSL Aplic WDP 303075 Power Socket with Energy Monitoring (#3991, #3996) +- Add support for Tuya Dimmer (#469, #4075) +- Add command Display to show all settings at once +- Add command SerialSend5 to send raw serial data like "A5074100545293" +- Add command WebRefresh 1000..10000 to control web page refresh in milliseconds. Default is 2345 +- Add command WeightRes 0..3 to control display of decimals for kilogram +- Add command RGBWWTable to support color calibration (#3933) +- Add command Reset 4 (reset to defaults but keep wifi params) and Reset 5 (as reset 4 and also erase flash) (#4061) +- Add command SetOption35 0..255 (seconds) to delay mDNS initialization to control possible Wifi connect problems +- Add command SetOption52 0/1 to control display of optional time offset from UTC in JSON messages (#3629, #3711) +- Add command SetOption53 0/1 to toggle gui display of Hostname and IP address (#1006, #2091) +- Add authentication to HTTP web pages +- Add decimals as input to commands PowerSet, VoltageSet and CurrentSet +- Add tools/decode-config.py by Norbert Richter to decode configuration data. See file for information +- Add define USE_DISPLAYS for selecting image sonoff-display +- Add define USE_BASIC for selecting image sonoff-basic without most sensors +- Add auto reload of main web page to some web restarts +- Add TasmotaModbus library as very basic modbus wrapper for TasmotaSerial +- Add more API callbacks and document API.md +- Add Apparent Power and Reactive Power to Energy Monitoring devices (#251) +- Add token %hostname% to command FullTopic (#3018) +- Add Wifi channel number to state message (#3664) +- Add user configurable GPIO02 and GPIO03 on H801 devices (#3692) +- Add toggle function RGBW lights (#3695, #3697) +- Add network information to display start screen (#3704) +- Add sleep to Nova Fitness SDS01X sensor (#2841, #3724, #3749) +- Add Analog input AD0 enabled to sonoff-sensors.bin (#3756, #3757) +- Add power value below 5W to Sonoff Pow R2 and S31 (#3745) +- Add RF Receiver control to module MagicHome to be used on Arilux LC10 (#3792) +- Add userid/password option to decode-status.py (#3796) +- Add delay after restart before processing rule sensor data (#3811) +- Add force_update to Home Assistant discovery (#3873) +- Add rule triggers SWITCH1#BOOT and POWER1#BOOT (#3904, #3910) +- Add Hebrew language file (#3960) +- Add TotalStartTime to Energy JSON message (#3971) +- Add whitespace removal from RfRaw and SerialSend5 (#4020) +- Add support for two BMP/BME sensors (#4195) ### 6.2.1 20180905 - * Fix possible ambiguity on command parameters if StateText contains numbers only (#3656) - * Fix Wemo emulation to select the first relay when more than one relay is present (#3657) - * Fix possible exception due to buffer overflow (#3659) - * Fix lost energy today and total energy value after power cycle (#3689) +- Fix possible ambiguity on command parameters if StateText contains numbers only (#3656) +- Fix Wemo emulation to select the first relay when more than one relay is present (#3657) +- Fix possible exception due to buffer overflow (#3659) +- Fix lost energy today and total energy value after power cycle (#3689) ### 6.2.0 20180901 - * Allow user override of define MAX_RULE_VARS and MAX_RULE_TIMERS (#3561) - * Disable wifi sleep for both Esp8266/Arduino core 2.4.1 and 2.4.2 to solve device freeze caused by Espressif SDK bug (#3554) - * Change DS18B20 driver to provide better instant results - * Change some sensor drivers to provide instant results - * Change define USE_ALL_SENSORS to USE_SENSORS as it doesn't contain all sensors due to duplicate I2C addresses - * Change some sensor update timings: AdcEvery 200 -> 250, Senseair 300 -> 250, SDM120 300 -> 250, SDM630 300 -> 250 - * Change default Wifi config option from WPS to Wifi Manager if WPS is disabled or Wifi Smartconfig if webserver is disabled or Wifi Serial input if Smartconfig is disabled - * Change SHT1x driver to provide better instant results and fix I2C interference - * Change DHT driver to provide better instant results and add decimals to DHT11 (#3164) - * Change DS18x20 driver to provide better instant results (#3169) - * Change CounterType 1 from milliseconds to microseconds (#3437) - * Change scheduler for better sleep support using Uptime, Delay, PulseTime and TelePeriod, Blinktime (#3581) - * Remove unused functionality from Sonoff-minimal to save space - * Remove WPS and SmartConfig from sonoff-minimal saving 56k code space - * Remove TSL2561 debug message and update library (#2415) - * Remove forced restart when sleep command is executed (#3554) - * Fix invalid response using more than 4 switches and domoticz - * Fix sonoff-minimal not using default settings - * Fix unsecure main webpage update - * Fix DHT driver mixing values for different sensors (#1797) - * Fix EnergyReset3 regression not clearing total energy (#2723) - * Fix rules once regression from v6.1.0 (#3198, #3226) - * Fix command Scale buffer overflow (#3236) - * Fix possible WDT due to long MQTT publish handling (#3313) - * Fix command TimeDst/TimeStd invalid JSON (#3322) - * Fix handling of default names when using names starting with shortcut character ",0,1 or 2 (#3392, #3600, #3618) - * Fix LM75AD I2C sensor detection (#3408) - * Fix iFan02 power on state (#3412, #3530) - * Fix some Pow R2 and S31 checksum errors using optimized re-sync (#3425) - * Fix SDM120 reporting wrong negative values to Domoticz (#3521) - * Fix MQTT reconnection detection when using TasmotaMqtt library (#3558) - * Fix OtaMagic when file path contains a dash (-) (#3563) - * Fix Sonoff Bridge data reception when using Portisch EFM8 firmware using in data buffer length (#3605) - * Add read sensor retry to DS18B20, DS18x20, DHT, SHT1X and HTU21 - * Add user selection of Wifi Smartconfig as define USE_SMARTCONFIG in user_config.h - * Add boot loop detection and perform some solutions - * Add wifi and mqtt status led blinkyblinky to be disabled by SetOption31 1. Does not work when LedPower is On (deliberate) (#871, #2230, #3114, #3155) - * Add support for TM1638 switch (#2226) - * Add GPIO options ButtonXn, SwitchXn and CounterXn to select INPUT mode instead of INPUT_PULLUP (#2525) - * Add support for APDS9960 proximity sensor (#3051) - * Add support for MPR121 controller in input mode for touch buttons (#3142) - * Add support for MCP230xx for general purpose input expansion and command Sensor29 (#3188) - * Add default Wifi Configuration tool as define WIFI_CONFIG_NO_SSID in user_config.h if no SSID is configured (#3224) - * Add command Timers 0/1 to globally disable or enable armed timers (#3270) - * Add support for CCS811 sensor (#3309) - * Add Turkish language file (#3332) - * Add command SerialSend4 to send binary serial data (#3345) - * Add initial support for sensor MPU6050 (#3352) - * Add rule triggers Wifi#Connected and Wifi#Disconnected (#3359) - * Add option + to command Rule to concatenate new rule with existing rules (#3365) - * Add message when JavaScript is not enabled in webbrowser (#3388) - * Add build time setting of ButtonTopic and SwitchTopic (#3414) - * Add iFan02 Fanspeed + and Fanspeed - command options (#3415) - * Add Individual HSBColorX commands (#3430, #3615) - * Add output support on MCP23008/MCP23017 (#3436) - * Add modulo option to rules like rule1 on Time#Minute|5 do backlog power on;delay 200;power off endon (#3466) - * Add RGB support for Domoticz (#3547) - * Add all ruletimer values to command RuleTimer result message (#3571) - * Add command Publish2 for publishing retained MQTT messages (#3593) - * Add commands ButtonDebounce 40..1000 and SwitchDebounce 40..1000 to have user control over debounce timing. Default is 50mS (#3594) - * Add RuleX debug options 8,9,10 (StopOnError) to control RuleX execution status after an exception restart (#3607) - * Add rule variables %sunrise%, %sunset%, %uptime% and %time% (#3608) - * Add optional MQTT_TELE_RETAIN to Energy Margins message (#3612, 3614) +- Allow user override of define MAX_RULE_VARS and MAX_RULE_TIMERS (#3561) +- Disable wifi sleep for both Esp8266/Arduino core 2.4.1 and 2.4.2 to solve device freeze caused by Espressif SDK bug (#3554) +- Change DS18B20 driver to provide better instant results +- Change some sensor drivers to provide instant results +- Change define USE_ALL_SENSORS to USE_SENSORS as it doesn't contain all sensors due to duplicate I2C addresses +- Change some sensor update timings: AdcEvery 200 -> 250, Senseair 300 -> 250, SDM120 300 -> 250, SDM630 300 -> 250 +- Change default Wifi config option from WPS to Wifi Manager if WPS is disabled or Wifi Smartconfig if webserver is disabled or Wifi Serial input if Smartconfig is disabled +- Change SHT1x driver to provide better instant results and fix I2C interference +- Change DHT driver to provide better instant results and add decimals to DHT11 (#3164) +- Change DS18x20 driver to provide better instant results (#3169) +- Change CounterType 1 from milliseconds to microseconds (#3437) +- Change scheduler for better sleep support using Uptime, Delay, PulseTime and TelePeriod, Blinktime (#3581) +- Remove unused functionality from Sonoff-minimal to save space +- Remove WPS and SmartConfig from sonoff-minimal saving 56k code space +- Remove TSL2561 debug message and update library (#2415) +- Remove forced restart when sleep command is executed (#3554) +- Fix invalid response using more than 4 switches and domoticz +- Fix sonoff-minimal not using default settings +- Fix unsecure main webpage update +- Fix DHT driver mixing values for different sensors (#1797) +- Fix EnergyReset3 regression not clearing total energy (#2723) +- Fix rules once regression from v6.1.0 (#3198, #3226) +- Fix command Scale buffer overflow (#3236) +- Fix possible WDT due to long MQTT publish handling (#3313) +- Fix command TimeDst/TimeStd invalid JSON (#3322) +- Fix handling of default names when using names starting with shortcut character ",0,1 or 2 (#3392, #3600, #3618) +- Fix LM75AD I2C sensor detection (#3408) +- Fix iFan02 power on state (#3412, #3530) +- Fix some Pow R2 and S31 checksum errors using optimized re-sync (#3425) +- Fix SDM120 reporting wrong negative values to Domoticz (#3521) +- Fix MQTT reconnection detection when using TasmotaMqtt library (#3558) +- Fix OtaMagic when file path contains a dash (-) (#3563) +- Fix Sonoff Bridge data reception when using Portisch EFM8 firmware using in data buffer length (#3605) +- Add read sensor retry to DS18B20, DS18x20, DHT, SHT1X and HTU21 +- Add user selection of Wifi Smartconfig as define USE_SMARTCONFIG in user_config.h +- Add boot loop detection and perform some solutions +- Add wifi and mqtt status led blinkyblinky to be disabled by SetOption31 1. Does not work when LedPower is On (deliberate) (#871, #2230, #3114, #3155) +- Add support for TM1638 switch (#2226) +- Add GPIO options ButtonXn, SwitchXn and CounterXn to select INPUT mode instead of INPUT_PULLUP (#2525) +- Add support for APDS9960 proximity sensor (#3051) +- Add support for MPR121 controller in input mode for touch buttons (#3142) +- Add support for MCP230xx for general purpose input expansion and command Sensor29 (#3188) +- Add default Wifi Configuration tool as define WIFI_CONFIG_NO_SSID in user_config.h if no SSID is configured (#3224) +- Add command Timers 0/1 to globally disable or enable armed timers (#3270) +- Add support for CCS811 sensor (#3309) +- Add Turkish language file (#3332) +- Add command SerialSend4 to send binary serial data (#3345) +- Add initial support for sensor MPU6050 (#3352) +- Add rule triggers Wifi#Connected and Wifi#Disconnected (#3359) +- Add option + to command Rule to concatenate new rule with existing rules (#3365) +- Add message when JavaScript is not enabled in webbrowser (#3388) +- Add build time setting of ButtonTopic and SwitchTopic (#3414) +- Add iFan02 Fanspeed + and Fanspeed - command options (#3415) +- Add Individual HSBColorX commands (#3430, #3615) +- Add output support on MCP23008/MCP23017 (#3436) +- Add modulo option to rules like rule1 on Time#Minute|5 do backlog power on;delay 200;power off endon (#3466) +- Add RGB support for Domoticz (#3547) +- Add all ruletimer values to command RuleTimer result message (#3571) +- Add command Publish2 for publishing retained MQTT messages (#3593) +- Add commands ButtonDebounce 40..1000 and SwitchDebounce 40..1000 to have user control over debounce timing. Default is 50mS (#3594) +- Add RuleX debug options 8,9,10 (StopOnError) to control RuleX execution status after an exception restart (#3607) +- Add rule variables %sunrise%, %sunset%, %uptime% and %time% (#3608) +- Add optional MQTT_TELE_RETAIN to Energy Margins message (#3612, 3614) ### 6.1.1 20180714 - * Revert wifi changes (#3177) - * Revert sonoff-minimal removals causing failure of wifi connection (#3177) +- Revert wifi changes (#3177) +- Revert sonoff-minimal removals causing failure of wifi connection (#3177) ### 6.1.0 20180706 - * Remove version 3, 4 and pre 5.2 settings auto-upgrade. See https://github.com/arendst/Tasmota/wiki/Upgrading#migration-path - * Change default CFG_HOLDER from 0x20161209 to 4617 (=0x1209) - no impact on default upgrades - * Change number of supported switches from 4 to 8 (#2885, #3086) - * Change BME680 driver from Adafruit to Bosch BME680 library (#2969) - * Fix Pzem004T checksum error - * Fix KNX bug when doing reply of sensors values - * Fix rules induced LWT message - * Fix possible wifi connection problem (#1366) - * Fix some Pow R2 and S31 checksum errors (#1907) - * Fix display selection of un-available GPIO options in Module Configuration webpage (#2718) - * Fix timer re-trigger within one minute after restart (#2744) - * Fix IRSend not accepting data value of 0 by David Conran (#2751) - * Fix vars on rules by Adrian Scillato (#2769) - * Fix bug in KNX menu by Adrian Scillato (#2770) - * Fix anomalies in rules (#2778) - * Fix HUE bridge V1 software version by Heiko Krupp (#2788) - * Fix Hardware Watchdog restart when using event command (#2853) - * Add Ukrainian language file - * Add KNX support for DS18S20 Temperature sensor - * Add CRC to Settings making future upgrades more fail-safe - * Add feature information to Status 4 - * Add tools folder with python script decode-status.py for decoding some status fields like SetOption and Features - * Add Slots on the KNX Web Menu to select Group Addess to receive data to trigger rules - * Add two rule sets of 511 characters using commands rule1, rule2 and rule3 - * Add Console Commands to send KNX Commands and KNX Values - * Add Slots on the KNX Web Menu to select Group Addess to send data from console commands - * Add Events to trigger rules when a command or read requests is received from KNX - * Add command SetOption30 to enforce Hass discovery as light group (#1784) - * Add support for BlitzWolf BW-SHP2 (and Homecube, Gosund SP1) Energy Monitoring Smart Socket (#2223) - * Add time in minutes to rule Time#Initialized, Time#set and Time#Minute (#2669) - * Add Eastron SDM630 energy meter by Gennaro Tortone (#2735) - * Add KNX communication enhancement by Adrian Scillato (#2742) - * Add KNX energy data by Adrian Scillato (#2750) - * Add rule support for IrReceive and RfReceive (#2758) - * Add python script fw-server.py in tools folder to create a simple OTA server by Gennaro Tortone (#2759) - * Add rule variables %time% for minutes since midnight, %uptime%, %sunrise% and %sunset% giving time in minutes (#2669) - * Add rules %mem1% to %mem5% variable names storing data in flash (#2780) - * Add rules test on %varx% or %memx% (#2780) - * Add optional token %id% substituting the unique MAC address to fulltopic by Michael Graf (#2794) - * Add support for Sonoff S26 Smart Socket (#2808) - * Add command WebSend [(:,:)] (#2821) - * Add increment and decrement value to command Counter (#2838) - * Add support for Sonoff iFan02 as module 44 introducing command FanSpeed 0..3 (#2839) - * Add source information to command execution to be shown with logging option 3 (#2843) - * Add support for uploading Sonoff Bridge firmware found in tools/fw_efm8bb1 folder build by Portisch using Web Gui File Upload (#2886) - * Add command RfRaw to control Portisch firmware features - * Add support for I2C temperature sensor LM75AD (#2909) - * Add option 0 to command Timers disarming all timers (#2962) - * Add performance improvement when updating multiple individual WS2812 pixels (#3007) - * Add command SetOption28 to switch between hex or decimal Sonoff Bridge RF received data format (#3008) - * Add command SetOption29 to switch between hex or decimal IR received data format - * Add decimal values support for commands ADD, SUB, MULT and SCALE (#3083, #3089) - * Add support for bitflags SetOption50 .. SetOption81 (#3118) +- Remove version 3, 4 and pre 5.2 settings auto-upgrade. See https://github.com/arendst/Tasmota/wiki/Upgrading#migration-path +- Change default CFG_HOLDER from 0x20161209 to 4617 (=0x1209) - no impact on default upgrades +- Change number of supported switches from 4 to 8 (#2885, #3086) +- Change BME680 driver from Adafruit to Bosch BME680 library (#2969) +- Fix Pzem004T checksum error +- Fix KNX bug when doing reply of sensors values +- Fix rules induced LWT message +- Fix possible wifi connection problem (#1366) +- Fix some Pow R2 and S31 checksum errors (#1907) +- Fix display selection of un-available GPIO options in Module Configuration webpage (#2718) +- Fix timer re-trigger within one minute after restart (#2744) +- Fix IRSend not accepting data value of 0 by David Conran (#2751) +- Fix vars on rules by Adrian Scillato (#2769) +- Fix bug in KNX menu by Adrian Scillato (#2770) +- Fix anomalies in rules (#2778) +- Fix HUE bridge V1 software version by Heiko Krupp (#2788) +- Fix Hardware Watchdog restart when using event command (#2853) +- Add Ukrainian language file +- Add KNX support for DS18S20 Temperature sensor +- Add CRC to Settings making future upgrades more fail-safe +- Add feature information to Status 4 +- Add tools folder with python script decode-status.py for decoding some status fields like SetOption and Features +- Add Slots on the KNX Web Menu to select Group Addess to receive data to trigger rules +- Add two rule sets of 511 characters using commands rule1, rule2 and rule3 +- Add Console Commands to send KNX Commands and KNX Values +- Add Slots on the KNX Web Menu to select Group Addess to send data from console commands +- Add Events to trigger rules when a command or read requests is received from KNX +- Add command SetOption30 to enforce Hass discovery as light group (#1784) +- Add support for BlitzWolf BW-SHP2 (and Homecube, Gosund SP1) Energy Monitoring Smart Socket (#2223) +- Add time in minutes to rule Time#Initialized, Time#set and Time#Minute (#2669) +- Add Eastron SDM630 energy meter by Gennaro Tortone (#2735) +- Add KNX communication enhancement by Adrian Scillato (#2742) +- Add KNX energy data by Adrian Scillato (#2750) +- Add rule support for IrReceive and RfReceive (#2758) +- Add python script fw-server.py in tools folder to create a simple OTA server by Gennaro Tortone (#2759) +- Add rule variables %time% for minutes since midnight, %uptime%, %sunrise% and %sunset% giving time in minutes (#2669) +- Add rules %mem1% to %mem5% variable names storing data in flash (#2780) +- Add rules test on %varx% or %memx% (#2780) +- Add optional token %id% substituting the unique MAC address to fulltopic by Michael Graf (#2794) +- Add support for Sonoff S26 Smart Socket (#2808) +- Add command WebSend [(:,:)] (#2821) +- Add increment and decrement value to command Counter (#2838) +- Add support for Sonoff iFan02 as module 44 introducing command FanSpeed 0..3 (#2839) +- Add source information to command execution to be shown with logging option 3 (#2843) +- Add support for uploading Sonoff Bridge firmware found in tools/fw_efm8bb1 folder build by Portisch using Web Gui File Upload (#2886) +- Add command RfRaw to control Portisch firmware features +- Add support for I2C temperature sensor LM75AD (#2909) +- Add option 0 to command Timers disarming all timers (#2962) +- Add performance improvement when updating multiple individual WS2812 pixels (#3007) +- Add command SetOption28 to switch between hex or decimal Sonoff Bridge RF received data format (#3008) +- Add command SetOption29 to switch between hex or decimal IR received data format +- Add decimal values support for commands ADD, SUB, MULT and SCALE (#3083, #3089) +- Add support for bitflags SetOption50 .. SetOption81 (#3118) ### 5.14.0 20180515 - * Update language files - * Update TasmotaSerial to 2.0.0 allowing Hardware Serial Fallback when correct connections are configured - * Change command handling - * Change user_config(_override).h defines TIME_STD and TIME_DST - * Change user_config(_override).h otaurl to http://sonoff.maddox.co.uk/tasmota/sonoff.bin (#2588, #2602) - * Fix configuration restore regression from 5.13.1 - * Fix compile error when ADC is enabled and Rules are disabled (#2608) - * Fix rule power trigger when no backlog command is used (#2613) - * Fix several timer data input and output errors (#2597, #2620) - * Fix KNX config error (#2628) - * Fix sensor MHZ-19 vanishing data over time (#2659) - * Fix KNX reconnection issue (#2679) - * Fix DST and STD time for Southern Hemisphere by Adrian Scillato (#2684, #2714) - * Add Portuguese in Brazil language file - * Add SetOption26 to enforce use of indexes even when only one relay is present (#1055) - * Add support for sensor SI1145 UV Index / IR / Visible light (#2496) - * Add rule state test for On/Off in addition to 0/1 (#2613) - * Add hardware serial option to MHZ-19 sensor (#2659) - * Add Eastron SDM120 energy meter by Gennaro Tortone (#2694) - * Add user entry DST/STD using commands TimeStd and TimeDst (See wiki for parameter syntax) (#2721) +- Update language files +- Update TasmotaSerial to 2.0.0 allowing Hardware Serial Fallback when correct connections are configured +- Change command handling +- Change user_config(_override).h defines TIME_STD and TIME_DST +- Change user_config(_override).h otaurl to http://sonoff.maddox.co.uk/tasmota/sonoff.bin (#2588, #2602) +- Fix configuration restore regression from 5.13.1 +- Fix compile error when ADC is enabled and Rules are disabled (#2608) +- Fix rule power trigger when no backlog command is used (#2613) +- Fix several timer data input and output errors (#2597, #2620) +- Fix KNX config error (#2628) +- Fix sensor MHZ-19 vanishing data over time (#2659) +- Fix KNX reconnection issue (#2679) +- Fix DST and STD time for Southern Hemisphere by Adrian Scillato (#2684, #2714) +- Add Portuguese in Brazil language file +- Add SetOption26 to enforce use of indexes even when only one relay is present (#1055) +- Add support for sensor SI1145 UV Index / IR / Visible light (#2496) +- Add rule state test for On/Off in addition to 0/1 (#2613) +- Add hardware serial option to MHZ-19 sensor (#2659) +- Add Eastron SDM120 energy meter by Gennaro Tortone (#2694) +- Add user entry DST/STD using commands TimeStd and TimeDst (See wiki for parameter syntax) (#2721) ### 5.13.1 20180501 - * Fix JSON buffers size too small for execution in some situations (#2580) - * Fix configuration restore (#2591) - * Add define MODULE for user selecting default model although it preferably should not be changed (#569, #2589) +- Fix JSON buffers size too small for execution in some situations (#2580) +- Fix configuration restore (#2591) +- Add define MODULE for user selecting default model although it preferably should not be changed (#569, #2589) ### 5.13.0 20180430 - * Change platformio option sonoff-ds18x20 to sonoff-allsensors enabling ds18x20 and all other sensors in one image - * Change status display of Ssid and SetOption - * Change default option SetOption15 from 0 to 1 providing better initial PWM experience - * Change webpage parameter communication - * Change max number of commands in Backlog from 15 to 30 and ignore commands overflowing - * Change TSL2561 driver to joba library and delete Adafruit library (#1644) - * Change default parameters in user_config.h to undefined for easy installation (#1851) - * Change max user configurable hold time from 10 to 25 seconds (#1851) - * Change Sonoff SC JSON format (#1939) - * Change Polish language to using Diacritics (#2005) - * Change user_config_override usage by providing user_config_override_sample.h (#2228) - * Change MQTT response topic for Energy changes from ENERGY to SENSOR (#2229, #2251) - * Change default Reset configuration time from 4 seconds to 40 seconds on Button hold (#2268) - * Change ESP8266 Analog JSON message from {"Analog0:123"} to {"ANALOG":{"A0:123"}} to accomodate rules (#2560) - * Change Counter JSON message from {"Counter1":0,"Counter3":0} to {"COUNTER":{"C1":0,"C3":0}} to accomodate rules - * Change ADS1115 JSON message from {"ADS1115":{"Analog0":123,"Analog1":123}} to {"ADS1115":{"A0":123,"A1":123}} - * Fix intermittent exception when dns lookup is used while sleep is enabled - * Fix 5.4.0 regression turning off single press after button hold during 4x hold time - * Fix possible wifi connection problem by erasing sdk configuration parameters - * Fix NTP sync to Thu Jan 01 08:00:10 1970 results in uptime 17651+ days (core2.4.1/sdk2.2.1) - * Fix MAX31850 higher temperatures (#1269) - * Fix freeing more code space when emulation is disabled (#1592) - * Fix providing web page configuratin option for Friendly Name when no device (relay or light) is configured (#1850) - * Fix compile error when define HOME_ASSISTANT_DISCOVERY_ENABLE is not set (#1937) - * Fix MQTT TLS fingerprint validation (#2033) - * Fix update temperature on DS18x20 drivers (#2328) - * Fix compile error when not defined USE_TIMERS (#2400) - * Fix configuration filename truncation when it contains spaces (#2484, #2490) - * Fix Energy Today and Yesterday overflow (#2543) - * Add serial debug info - * Add Portuguese language file - * Add Czech language file - * Add Bulgarian language file - * Add Domoticz dust (custom) sensors to PMS5003 and NovaFitness SDS drivers as PM1, PM2.5 and PM10 - * Add commands Publish, Rule, RuleTimer and Event. See Wiki about Rule restriction, usage and examples - * Add sonoff-classic, sonoff-allsensors and sonoff-knx - * Add some coloring to important web buttons - * Add support for sensor HC-SR04 ultrasonic (#113, #1964, #2444) - * Add define MQTT_TELE_RETAIN compile option default set to 0 (#1071) - * Add 16 timers using commands Timer and Timers (#1091) - * Add optional Timer configuration webpage to be enabled in user_config.h with define USE_TIMERS_WEB - * Add Multichannel Gas sensor using MultiChannel_Gas_Sensor library (#1245) - * Add Domoticz Battery and RSSI Quality (#1604) - * Add command HSBColor Hue,Sat,Bri (#1642, #2203) - * Add compile time support for WS2812 BRG and RBG led configurations to be defined in user_config.h (#1690) - * Add optional usage of %d or %X suffices in MQTT client to append chipid (#1871) - * Add optional usage of %d or %X suffices in MQTT topic to append chipid (#1871) - * Add optional usage of %d or %04d in ota url to be replaced with chipid (#1871) - * Add Sonoff Bridge command RfKey 5 to show current RF key values either default or learned (#1884) - * Add user configurable serial GPIOs to MagicHome and Arilux modules (#1887) - * Add Russian language file (#1909) - * Add Webserver upload preflight request support (#1927) - * Add Home Assistant clear other device (#1931) - * Add Restart time to Status 1 (#1938) - * Add optional TSL2561 driver using library Joba_Tsl2561 to be enabled in user_config.h with define USE_TSL2561_JOBA (#1951) - * Add support for sensor SHTC3 (#1967) - * Add compiler check for stable lwIP version v1.4 (#1940) - * Add support for multiple SHT3X sensors (#1949, #2110) - * Add always suffix with device number in Mqtt discovery topic (#1962) - * Add support for optional MQTT drivers to be selected in user_config.h (#1992) - * Add optional Arduino OTA support to be enabled in user_config.h (#1998) - * Add diacritics to Polish language file (#2005) - * Add Hungarian language file (#2024) - * Add support for Nova Fitness SDS011 and possibly SDS021 particle concentration sensor (#2070) - * Add single decimal precision to Nova Fitness SDS0x1 sensor values (#2093) - * Add Chinese (Traditional) in Taiwan language file (#2108) - * Add Sonoff SC domoticz support for Sound level as Counter and Air quality (#2118) - * Add a second TLS fingerprint to allow switching keys in TLS mode (#2033, #2102) - * Add display of remaining pulse time to command PulseTime (#2085) - * Add additional time offset to Wifi Retry based on device mac address (#2089) - * Add command Color6 RRGGBB for Clock hour marker color and command Rotation pixels for Clock rotation (#2092) - * Add HTML language header in local language (#2123) - * Add command PowerDelta 0..100 (percentage) to Energy monitoring devices to report on active power load change (#2157) - * Add Restart Reason to Status 1 report (#2161) - * Add command Channel 0..100 to control dimmer value for individual color channels (#2111, #2203) - * Add support for Hardware Serial bridge using commands SerialDelimiter, Baudrate and SerialSend. Supports 8N1 and text only (#2182) - * Add support for Software Serial bridge using commands SerialDelimiter, SBaudrate and SSerialSend. Supports 8N1 and text only (#2190) - * Add support for Zengge WF017 PWM Led strip controller (#2202) - * Add PWM status to command State if PWM enabled (#2203) - * Add all FriendlyNames to Status information (#2208) - * Add Channel status information (#2211) - * Add hexadecimal Data entry to command IrSend using 0x notation (#1290, #2314) - * Add Home Assistant MQTT Discovery for Buttons and change SetOption19 response (#2277) - * Add multiple color entry support for command Led like Led2 120000 001200 000012 setting led2 as Red, Led3 as Green and Led4 as Blue (#2303) - * Add hexadecimal RGB color entry on RGBCW leds (#2304) - * Add support for SGP30 gas and air quality sensor (#2307) - * Add optional Sunrise and Sunset timers with commands Latitide and Longitude to be enabled with define USE_SUNRISE in user_config.h (#2317) - * Add timer sunrise and sunset offset (#2378) - * Add user selectable defines for Sunrise/set Dawn option (#2378) - * Add optional KNX IP Protocol Support (#2402) - * Add random window to timers (#2447) - * Add Greek language file (#2491) - * Add support for Sonoff Pow R2 (#2340) - * Add GPIO_User to GPIO02 for all Sonoff T1 (#2524) +- Change platformio option sonoff-ds18x20 to sonoff-allsensors enabling ds18x20 and all other sensors in one image +- Change status display of Ssid and SetOption +- Change default option SetOption15 from 0 to 1 providing better initial PWM experience +- Change webpage parameter communication +- Change max number of commands in Backlog from 15 to 30 and ignore commands overflowing +- Change TSL2561 driver to joba library and delete Adafruit library (#1644) +- Change default parameters in user_config.h to undefined for easy installation (#1851) +- Change max user configurable hold time from 10 to 25 seconds (#1851) +- Change Sonoff SC JSON format (#1939) +- Change Polish language to using Diacritics (#2005) +- Change user_config_override usage by providing user_config_override_sample.h (#2228) +- Change MQTT response topic for Energy changes from ENERGY to SENSOR (#2229, #2251) +- Change default Reset configuration time from 4 seconds to 40 seconds on Button hold (#2268) +- Change ESP8266 Analog JSON message from {"Analog0:123"} to {"ANALOG":{"A0:123"}} to accomodate rules (#2560) +- Change Counter JSON message from {"Counter1":0,"Counter3":0} to {"COUNTER":{"C1":0,"C3":0}} to accomodate rules +- Change ADS1115 JSON message from {"ADS1115":{"Analog0":123,"Analog1":123}} to {"ADS1115":{"A0":123,"A1":123}} +- Fix intermittent exception when dns lookup is used while sleep is enabled +- Fix 5.4.0 regression turning off single press after button hold during 4x hold time +- Fix possible wifi connection problem by erasing sdk configuration parameters +- Fix NTP sync to Thu Jan 01 08:00:10 1970 results in uptime 17651+ days (core2.4.1/sdk2.2.1) +- Fix MAX31850 higher temperatures (#1269) +- Fix freeing more code space when emulation is disabled (#1592) +- Fix providing web page configuratin option for Friendly Name when no device (relay or light) is configured (#1850) +- Fix compile error when define HOME_ASSISTANT_DISCOVERY_ENABLE is not set (#1937) +- Fix MQTT TLS fingerprint validation (#2033) +- Fix update temperature on DS18x20 drivers (#2328) +- Fix compile error when not defined USE_TIMERS (#2400) +- Fix configuration filename truncation when it contains spaces (#2484, #2490) +- Fix Energy Today and Yesterday overflow (#2543) +- Add serial debug info +- Add Portuguese language file +- Add Czech language file +- Add Bulgarian language file +- Add Domoticz dust (custom) sensors to PMS5003 and NovaFitness SDS drivers as PM1, PM2.5 and PM10 +- Add commands Publish, Rule, RuleTimer and Event. See Wiki about Rule restriction, usage and examples +- Add sonoff-classic, sonoff-allsensors and sonoff-knx +- Add some coloring to important web buttons +- Add support for sensor HC-SR04 ultrasonic (#113, #1964, #2444) +- Add define MQTT_TELE_RETAIN compile option default set to 0 (#1071) +- Add 16 timers using commands Timer and Timers (#1091) +- Add optional Timer configuration webpage to be enabled in user_config.h with define USE_TIMERS_WEB +- Add Multichannel Gas sensor using MultiChannel_Gas_Sensor library (#1245) +- Add Domoticz Battery and RSSI Quality (#1604) +- Add command HSBColor Hue,Sat,Bri (#1642, #2203) +- Add compile time support for WS2812 BRG and RBG led configurations to be defined in user_config.h (#1690) +- Add optional usage of %d or %X suffices in MQTT client to append chipid (#1871) +- Add optional usage of %d or %X suffices in MQTT topic to append chipid (#1871) +- Add optional usage of %d or %04d in ota url to be replaced with chipid (#1871) +- Add Sonoff Bridge command RfKey 5 to show current RF key values either default or learned (#1884) +- Add user configurable serial GPIOs to MagicHome and Arilux modules (#1887) +- Add Russian language file (#1909) +- Add Webserver upload preflight request support (#1927) +- Add Home Assistant clear other device (#1931) +- Add Restart time to Status 1 (#1938) +- Add optional TSL2561 driver using library Joba_Tsl2561 to be enabled in user_config.h with define USE_TSL2561_JOBA (#1951) +- Add support for sensor SHTC3 (#1967) +- Add compiler check for stable lwIP version v1.4 (#1940) +- Add support for multiple SHT3X sensors (#1949, #2110) +- Add always suffix with device number in Mqtt discovery topic (#1962) +- Add support for optional MQTT drivers to be selected in user_config.h (#1992) +- Add optional Arduino OTA support to be enabled in user_config.h (#1998) +- Add diacritics to Polish language file (#2005) +- Add Hungarian language file (#2024) +- Add support for Nova Fitness SDS011 and possibly SDS021 particle concentration sensor (#2070) +- Add single decimal precision to Nova Fitness SDS0x1 sensor values (#2093) +- Add Chinese (Traditional) in Taiwan language file (#2108) +- Add Sonoff SC domoticz support for Sound level as Counter and Air quality (#2118) +- Add a second TLS fingerprint to allow switching keys in TLS mode (#2033, #2102) +- Add display of remaining pulse time to command PulseTime (#2085) +- Add additional time offset to Wifi Retry based on device mac address (#2089) +- Add command Color6 RRGGBB for Clock hour marker color and command Rotation pixels for Clock rotation (#2092) +- Add HTML language header in local language (#2123) +- Add command PowerDelta 0..100 (percentage) to Energy monitoring devices to report on active power load change (#2157) +- Add Restart Reason to Status 1 report (#2161) +- Add command Channel 0..100 to control dimmer value for individual color channels (#2111, #2203) +- Add support for Hardware Serial bridge using commands SerialDelimiter, Baudrate and SerialSend. Supports 8N1 and text only (#2182) +- Add support for Software Serial bridge using commands SerialDelimiter, SBaudrate and SSerialSend. Supports 8N1 and text only (#2190) +- Add support for Zengge WF017 PWM Led strip controller (#2202) +- Add PWM status to command State if PWM enabled (#2203) +- Add all FriendlyNames to Status information (#2208) +- Add Channel status information (#2211) +- Add hexadecimal Data entry to command IrSend using 0x notation (#1290, #2314) +- Add Home Assistant MQTT Discovery for Buttons and change SetOption19 response (#2277) +- Add multiple color entry support for command Led like Led2 120000 001200 000012 setting led2 as Red, Led3 as Green and Led4 as Blue (#2303) +- Add hexadecimal RGB color entry on RGBCW leds (#2304) +- Add support for SGP30 gas and air quality sensor (#2307) +- Add optional Sunrise and Sunset timers with commands Latitide and Longitude to be enabled with define USE_SUNRISE in user_config.h (#2317) +- Add timer sunrise and sunset offset (#2378) +- Add user selectable defines for Sunrise/set Dawn option (#2378) +- Add optional KNX IP Protocol Support (#2402) +- Add random window to timers (#2447) +- Add Greek language file (#2491) +- Add support for Sonoff Pow R2 (#2340) +- Add GPIO_User to GPIO02 for all Sonoff T1 (#2524) ### 5.12.0 20180209 - * Change library PubSubClient.h define MQTT_MAX_PACKET_SIZE from 512 to 1000 for Home Assistant support - * Change relation of define MESSZ being dependent on PubSubClient.h define MQTT_MAX_PACKET_SIZE - * Change command color parameter input checks to less strict for Home Assistant support - * Change command Ina219Mode into command Sensor13 - * Change commands HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to be used for both Pow and S31 calibration - * Change commands HlwPSet, HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used for both Pow and S31 calibration - * Change uptime from hour to second resulting in a display of 123T13:45:21 where 123 is days - * Change module name Wemos D1 mini into Generic (#1220) - * Change HTML from width=100% to style=width:100% supporting HTML5 (#1358) - * Change OSWATCH_RESET_TIME (Blocked loop) from 30 to 120 seconds to allow slow networks (#1556) - * Change WIFI_MANAGER_SEC into WIFI_CONFIG_SEC (#1616) - * Change function pointers code to save code space and memory (#1683) - * Change webserver argument processing gaining 5k code space (#1705) - * Change weblog memory usage (#1730, #1793, #1819) - * Update TasmotaSerial library to 1.1.0 - * Update language files Italian (#1594), Dutch (#1723) and Spanish (#1722) - * Fix Non-English JSON temperature unit attachement - * Fix Arilux RF induced exception by moving interrupt handler to iram on non ESP8266/Arduino lib v2.3.0 - * Fix truncated command names and wrong response for DomoticzSwitchIdx (#1571) - * Fix %-sign issue as printf escape character in Humidity and Sonoff SC (#1579) - * Fix DS18B20 temperature JSON decimal dot (#1561) - * Fix Energy JSON message (#1621) - * Fix IRSend parameter translation (#1636) - * Fix TSL2561 device detection (#1644, #1825) - * Fix BME680 teleperiod resistance measuring (#1647) - * Fix Energy Monitoring Energy Today and Energy Total reading after restart (#1648) - * Fix IRReceive Data value (#1663) - * Fix Energy Monitoring Energy Period roll-over (#1688) - * Fix compiler warnings (#1774) - * Fix command PWM response if no PWM channel is configured (#1783) - * Add locale Decimal Separator to Web sensor page - * Add ColorTemperature to light status message - * Add command PowerOnState option 5 which inverts PulseTime and allows for delayed always on after power on - * Add OtaMagic two step Web server OTA upgrade using filename-minimal image if OTA free space is too small - * Add support for PMS5003 and PMS7003 particle concentration sensor - * Add command SetOption21 1 to allow Energy Monitoring when power is off on Sonoff Pow and Sonoff S31 (#1420) - * Add Chinese language file (#1551) - * Add French language file (#1561) - * Add Spanish language file (#1589) - * Add HTTP Allow Cross Origin removed from ESP8266/Arduino lib v2.4.0 (#1572) - * Add Home Assistant MQTT Discovery for switch and light to be enabled by command SetOption19 1 (#1534) or define HOME_ASSISTANT_DISCOVERY_ENABLE in user_config.h (#1685) - * Add command State to retrieve device state information (same data as teleperiod state and status 11 in slightly different JSON format) - * Add optional login to Webserver AP mode (#1587, #1635) - * Add command Sensor15 2 to start MHZ19(B) Zero Point Calibration (#1643) - * Add support for Sonoff S31 Smart Socket with Power Consumption Detection (#1626) - * Add command SetOption20 to allow update of Dimmer/Color/Ct without turning power on (#1719, #1741) - * Add NTP sync time slot based on chip id (#1773) - * Add cursor pointer to web button (#1836) +- Change library PubSubClient.h define MQTT_MAX_PACKET_SIZE from 512 to 1000 for Home Assistant support +- Change relation of define MESSZ being dependent on PubSubClient.h define MQTT_MAX_PACKET_SIZE +- Change command color parameter input checks to less strict for Home Assistant support +- Change command Ina219Mode into command Sensor13 +- Change commands HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to be used for both Pow and S31 calibration +- Change commands HlwPSet, HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used for both Pow and S31 calibration +- Change uptime from hour to second resulting in a display of 123T13:45:21 where 123 is days +- Change module name Wemos D1 mini into Generic (#1220) +- Change HTML from width=100% to style=width:100% supporting HTML5 (#1358) +- Change OSWATCH_RESET_TIME (Blocked loop) from 30 to 120 seconds to allow slow networks (#1556) +- Change WIFI_MANAGER_SEC into WIFI_CONFIG_SEC (#1616) +- Change function pointers code to save code space and memory (#1683) +- Change webserver argument processing gaining 5k code space (#1705) +- Change weblog memory usage (#1730, #1793, #1819) +- Update TasmotaSerial library to 1.1.0 +- Update language files Italian (#1594), Dutch (#1723) and Spanish (#1722) +- Fix Non-English JSON temperature unit attachement +- Fix Arilux RF induced exception by moving interrupt handler to iram on non ESP8266/Arduino lib v2.3.0 +- Fix truncated command names and wrong response for DomoticzSwitchIdx (#1571) +- Fix %-sign issue as printf escape character in Humidity and Sonoff SC (#1579) +- Fix DS18B20 temperature JSON decimal dot (#1561) +- Fix Energy JSON message (#1621) +- Fix IRSend parameter translation (#1636) +- Fix TSL2561 device detection (#1644, #1825) +- Fix BME680 teleperiod resistance measuring (#1647) +- Fix Energy Monitoring Energy Today and Energy Total reading after restart (#1648) +- Fix IRReceive Data value (#1663) +- Fix Energy Monitoring Energy Period roll-over (#1688) +- Fix compiler warnings (#1774) +- Fix command PWM response if no PWM channel is configured (#1783) +- Add locale Decimal Separator to Web sensor page +- Add ColorTemperature to light status message +- Add command PowerOnState option 5 which inverts PulseTime and allows for delayed always on after power on +- Add OtaMagic two step Web server OTA upgrade using filename-minimal image if OTA free space is too small +- Add support for PMS5003 and PMS7003 particle concentration sensor +- Add command SetOption21 1 to allow Energy Monitoring when power is off on Sonoff Pow and Sonoff S31 (#1420) +- Add Chinese language file (#1551) +- Add French language file (#1561) +- Add Spanish language file (#1589) +- Add HTTP Allow Cross Origin removed from ESP8266/Arduino lib v2.4.0 (#1572) +- Add Home Assistant MQTT Discovery for switch and light to be enabled by command SetOption19 1 (#1534) or define HOME_ASSISTANT_DISCOVERY_ENABLE in user_config.h (#1685) +- Add command State to retrieve device state information (same data as teleperiod state and status 11 in slightly different JSON format) +- Add optional login to Webserver AP mode (#1587, #1635) +- Add command Sensor15 2 to start MHZ19(B) Zero Point Calibration (#1643) +- Add support for Sonoff S31 Smart Socket with Power Consumption Detection (#1626) +- Add command SetOption20 to allow update of Dimmer/Color/Ct without turning power on (#1719, #1741) +- Add NTP sync time slot based on chip id (#1773) +- Add cursor pointer to web button (#1836) ### 5.11.1 20180107 - * Fix Sonoff Pow command handling (#1542) +- Fix Sonoff Pow command handling (#1542) ### 5.11.0 20180107 - * Minor webpage HTML optimizations (#1358) - * Updated German translation (#1438) - * Change Sonoff Pow Energy MQTT data message and consolidate Status 8 into Status 10 - * Change ADS1115 default voltage range from +/-2V to +/-6V (#1289) - * Change text to Active for 3 minutes (#1364) - * Change Wemo SetBinaryState to distinguish from GetBinaryState (#1357) - * Change output of HTTP command to valid JSON and Array only (#1363) - * Removed all MQTT, JSON and Command language defines from locale files and set fixed to English (#1473) - * Renamed commands Color2,3,4 to Color3,4,5 - * Fix BME280 calculation (#1051) - * Fix Sonoff Bridge missed learned key if learned data contains 0x55 (End of Transmission) flag (#1095, #1294) - * Fix PWM initialization in Dimmer/Color mode (#1321) - * Fix Wemo Emulation (#1357) - * Fix display of build date and time in non-english locale (#1465) - * Fix Wemo and Hue emulation by adding M-Search response delay (#1486) - * Add libraries Adafruit_BME680-1.0.5, Adafruit_Sensor-1.0.2.02, TasmotaSerial-1.0.0 and TSL2561-Arduino-Library - * Add command Color2 to set color while keeping same dimmer value - * Add device function pointers - * Add support for SenseAir S8 CO2 sensor - * Add color led signal to Carbon Dioxide (CO2) sensors using defines CO2_LOW and CO2_HIGH in user_config.h - * Add support for Domoticz Air Quality sensor to be used by MH-Z19(B) and SenseAir sensors - * Add support for PZEM004T energy sensor - * Add support for iTead SI7021 temperature and humidity sensor by consolidating DHT22 into AM2301 and using former DHT22 as SI7021 (#735) - * Add support for BME680 using adafruit libraries (#1212) - * Add support for MH-Z19(B) CO2 sensor (#561, #1248) - * Add multipress support and more user configurable GPIO to Sonoff Dual R2 (#1291) - * Add support for TSL2561 using adafruit library (#661, #1311) - * Add support for SHT3x (#1314) - * Add support for Arilux LC06 (#1414) - * Add Italian language file (#1449) - * Add 2nd Gen Alexa support to Wemo emulation discovery (#1357, #1450) - * Add define for additional number of WS2812 schemes (#1463) +- Minor webpage HTML optimizations (#1358) +- Updated German translation (#1438) +- Change Sonoff Pow Energy MQTT data message and consolidate Status 8 into Status 10 +- Change ADS1115 default voltage range from +/-2V to +/-6V (#1289) +- Change text to Active for 3 minutes (#1364) +- Change Wemo SetBinaryState to distinguish from GetBinaryState (#1357) +- Change output of HTTP command to valid JSON and Array only (#1363) +- Removed all MQTT, JSON and Command language defines from locale files and set fixed to English (#1473) +- Renamed commands Color2,3,4 to Color3,4,5 +- Fix BME280 calculation (#1051) +- Fix Sonoff Bridge missed learned key if learned data contains 0x55 (End of Transmission) flag (#1095, #1294) +- Fix PWM initialization in Dimmer/Color mode (#1321) +- Fix Wemo Emulation (#1357) +- Fix display of build date and time in non-english locale (#1465) +- Fix Wemo and Hue emulation by adding M-Search response delay (#1486) +- Add libraries Adafruit_BME680-1.0.5, Adafruit_Sensor-1.0.2.02, TasmotaSerial-1.0.0 and TSL2561-Arduino-Library +- Add command Color2 to set color while keeping same dimmer value +- Add device function pointers +- Add support for SenseAir S8 CO2 sensor +- Add color led signal to Carbon Dioxide (CO2) sensors using defines CO2_LOW and CO2_HIGH in user_config.h +- Add support for Domoticz Air Quality sensor to be used by MH-Z19(B) and SenseAir sensors +- Add support for PZEM004T energy sensor +- Add support for iTead SI7021 temperature and humidity sensor by consolidating DHT22 into AM2301 and using former DHT22 as SI7021 (#735) +- Add support for BME680 using adafruit libraries (#1212) +- Add support for MH-Z19(B) CO2 sensor (#561, #1248) +- Add multipress support and more user configurable GPIO to Sonoff Dual R2 (#1291) +- Add support for TSL2561 using adafruit library (#661, #1311) +- Add support for SHT3x (#1314) +- Add support for Arilux LC06 (#1414) +- Add Italian language file (#1449) +- Add 2nd Gen Alexa support to Wemo emulation discovery (#1357, #1450) +- Add define for additional number of WS2812 schemes (#1463) ### 5.10.0 20171201 - * Upgrade library ArduinoJson to 5.11.2 - * Upgrade library IRRemoteEsp8266 to 2.2.1 + 2 commits but disabled some protocols (code size reduction) - * Upgrade library NeoPixelBus to 2.2.9 - * Upgrade library OneWire to 2.3.3 + 6 commits and disabled CRC lookup-table (#define ONEWIRE_CRC8_TABLE 0) (code size reduction) - * Update library PubSubClient to 2.6 + 9 commits and additional delay (#790) - * Update core_esp8266_wiring_digital.c to latest (staged) level - * Patch library I2Cdevlib-Core for esp8266-core 2.4.0-rc2 compatibility - * Remove command EnergyReset 1..3 now replaced by EnergyReset1 to EnergyReset3 - * Remove spaces in JSON messages (code size reduction) - * Renamed xsns_05_ds18x20.ino to xsns_05_ds18x20_legacy.ino still using library OneWire and providing dynamic sensor scan - * Fix possible iram1_0_seg compile error by shrinking ICACHE_RAM_ATTR code usage - * Fix PWM watchdog timeout if Dimmer is set to 100 or Color set to 0xFF (#1146) - * Fix Sonoff Bridge Learn Mode hang caused by unrecognised RF code (#1181) - * Fix blank console log window by using XML character encoding (#1187) - * Fix wrong response name for command HlwISet (#1214) - * Fix DHT type sensor timeout recognition by distinguish "signal already there" from "timeout" (#1233) - * Add fixed color options 1..12 to command Color - * Add + (plus) and - (minus) to commands Dimmer (+10/-10), Speed and Scheme - * Add + (plus) and - (minus) to command Color to select 1 out of 12 preset colors - * Add + (plus) and - (minus) to command Ct to control ColdWarm led ColorTemperature (+34/-34) - * Add commands EnergyReset1 0..42500, EnergyReset2 0..42500 and EnergyReset3 0..42500000 - * to (Re)set Energy Today, Yesterday or Total respectively in Wh (#406, #685, #1202) - * Add optional ADS1115 driver as alternative for unsupported I2Cdevlib in esp8266-core 2.4.0-rc2 - * Add support for INA219 Voltage and Current sensor to be enabled in user_config.h with define USE_INA219 - * Add support for Arilux LC11 (Clearing RF home code when selecting no Arilux module) - * Add support for WS2812 RGBW ledstrips to be enabled in user_config.h with define USE_WS2812_CTYPE (#1156) - * Add SettingsSaveAll routine to command SaveData to be used before controlled power down (#1202) - * Add option PUSHBUTTON_TOGGLE (SwitchMode 7) to allow toggling on any switch change (#1221) - * Add new xdrv_05_ds18x20.ino free from library OneWire and add the following features: - * Add support for DS1822 - * Add forced setting of 12-bit resolution for selected device types (#1222) - * Add read temperature retry counter (#1215) - * Fix lost sensors by performing sensor probe at restart only thereby removing dynamic sensor probe (#1215) - * Fix sensor address sorting using ascending sort on sensor type followed by sensor address - * Rewrite JSON resulting in shorter message allowing more sensors in default firmware image: - * "DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6} - * Add additional define in user_config.h to select either single sensor (defines disabled), new multi sensor (USE_DS18X20) or legacy multi sensor (USE_DS18X20_LEGACY) - * Add clock support for more different pixel counts (#1226) - * Add support for Sonoff Dual R2 (#1249) - * Add FriendlyName to web page tab and add program information to web page footer (#1275) +- Upgrade library ArduinoJson to 5.11.2 +- Upgrade library IRRemoteEsp8266 to 2.2.1 + 2 commits but disabled some protocols (code size reduction) +- Upgrade library NeoPixelBus to 2.2.9 +- Upgrade library OneWire to 2.3.3 + 6 commits and disabled CRC lookup-table (#define ONEWIRE_CRC8_TABLE 0) (code size reduction) +- Update library PubSubClient to 2.6 + 9 commits and additional delay (#790) +- Update core_esp8266_wiring_digital.c to latest (staged) level +- Patch library I2Cdevlib-Core for esp8266-core 2.4.0-rc2 compatibility +- Remove command EnergyReset 1..3 now replaced by EnergyReset1 to EnergyReset3 +- Remove spaces in JSON messages (code size reduction) +- Renamed xsns_05_ds18x20.ino to xsns_05_ds18x20_legacy.ino still using library OneWire and providing dynamic sensor scan +- Fix possible iram1_0_seg compile error by shrinking ICACHE_RAM_ATTR code usage +- Fix PWM watchdog timeout if Dimmer is set to 100 or Color set to 0xFF (#1146) +- Fix Sonoff Bridge Learn Mode hang caused by unrecognised RF code (#1181) +- Fix blank console log window by using XML character encoding (#1187) +- Fix wrong response name for command HlwISet (#1214) +- Fix DHT type sensor timeout recognition by distinguish "signal already there" from "timeout" (#1233) +- Add fixed color options 1..12 to command Color +- Add + (plus) and - (minus) to commands Dimmer (+10/-10), Speed and Scheme +- Add + (plus) and - (minus) to command Color to select 1 out of 12 preset colors +- Add + (plus) and - (minus) to command Ct to control ColdWarm led ColorTemperature (+34/-34) +- Add commands EnergyReset1 0..42500, EnergyReset2 0..42500 and EnergyReset3 0..42500000 +- to (Re)set Energy Today, Yesterday or Total respectively in Wh (#406, #685, #1202) +- Add optional ADS1115 driver as alternative for unsupported I2Cdevlib in esp8266-core 2.4.0-rc2 +- Add support for INA219 Voltage and Current sensor to be enabled in user_config.h with define USE_INA219 +- Add support for Arilux LC11 (Clearing RF home code when selecting no Arilux module) +- Add support for WS2812 RGBW ledstrips to be enabled in user_config.h with define USE_WS2812_CTYPE (#1156) +- Add SettingsSaveAll routine to command SaveData to be used before controlled power down (#1202) +- Add option PUSHBUTTON_TOGGLE (SwitchMode 7) to allow toggling on any switch change (#1221) +- Add new xdrv_05_ds18x20.ino free from library OneWire and add the following features: +- Add support for DS1822 +- Add forced setting of 12-bit resolution for selected device types (#1222) +- Add read temperature retry counter (#1215) +- Fix lost sensors by performing sensor probe at restart only thereby removing dynamic sensor probe (#1215) +- Fix sensor address sorting using ascending sort on sensor type followed by sensor address +- Rewrite JSON resulting in shorter message allowing more sensors in default firmware image: +- "DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6} +- Add additional define in user_config.h to select either single sensor (defines disabled), new multi sensor (USE_DS18X20) or legacy multi sensor (USE_DS18X20_LEGACY) +- Add clock support for more different pixel counts (#1226) +- Add support for Sonoff Dual R2 (#1249) +- Add FriendlyName to web page tab and add program information to web page footer (#1275) ### 5.9.1 20171107 - * Add external sensor function pointer interface to enable easy sensor addition - * Add support for ADS1115 to be enabled in user_config.h and needs libraries i2cdevlib-Core and i2cdevlib-ADS1115 (#338, #660) - * Fix Backup Configuration file download failure by defining proper file size (#1115) - * Fix Exception 26 and empty console screen after usage of command WakeupDuration (#1133) - * Fix some changed iTead web links in README.md (#1137) +- Add external sensor function pointer interface to enable easy sensor addition +- Add support for ADS1115 to be enabled in user_config.h and needs libraries i2cdevlib-Core and i2cdevlib-ADS1115 (#338, #660) +- Fix Backup Configuration file download failure by defining proper file size (#1115) +- Fix Exception 26 and empty console screen after usage of command WakeupDuration (#1133) +- Fix some changed iTead web links in README.md (#1137) ### 5.9.0 20171030 - * Rewrite code (partly) using Google C++ Style Guide (https://google.github.io/styleguide/cppguide.html) - * Rewrite code by using command lookup tables and javascript (client side) web page expansions - * Change HTML/CSS to enable nicer form field entry - * Change default PWM assignments for H801 RGB(CW) led controller to support optional Color/Dimmer control - * GPIO04 (W2) from GPIO_PWM2 to GPIO_USER to be user configurable for GPIO_PWM5 (second White - Warm if W1 is Cold) - * GPIO12 (Blue) GPIO_PWM3 no change - * GPIO13 (Green) from GPIO_PWM4 to GPIO_PWM2 - * GPIO14 (W1) from GPIO_PWM1 to GPIO_USER to be user configurable for GPIO_PWM4 (first White - Cold or Warm) - * GPIO15 (Red) from GPIO_PWM5 to GPIO_PWM1 - * Change default PWM assignments for MagicHome RGB(W) led controller to support optional Color/Dimmer control - * GPIO05 (Green) from GPIO_PWM4 to GPIO_PWM2 - * GPIO12 (Blue) from GPIO_PWM5 to GPIO_PWM3 - * GPIO13 (White) GPIO_USER to be user configurable for GPIO_PWM4 (White - Cold or Warm) - * GPIO14 (Red) from GPIO_PWM3 to GPIO_PWM1 - * Change default PWM assignment for Witty Cloud to support optional Color/Dimmer control (#976) - * GPIO12 (Green) from GPIO_PWM4 to GPIO_PWM2 - * GPIO13 (Blue) from GPIO_PWM5 to GPIO_PWM3 - * GPIO15 (Red) from GPIO_PWM3 to GPIO_PWM1 - * Change when another module is selected now all GPIO user configuration is removed - * Change command name IRRemote to IRSend (#956) - * Remove Arduino IDE version too low warning as it interferes with platformio.ini platform = espressif8266_stage - * Fix command FullTopic entry when using serial or console interface - * Fix possible UDP syslog blocking - * Fix minimum TelePeriod of 10 seconds set by web page - * Fix command GPIOx JSON response (#897) - * Fix inverted relay power on state (#909) - * Fix compile error when DOMOTICZ_UPDATE_TIMER is not defined (#930) - * Fix alignment of web page items in some browsers (#935) - * Fix setting all saved power settings to Off when SetOption0 (SaveState) = 0 (#955) - * Fix timezone range from -12/12 to -13/13 (#968) - * Fix Southern Hemisphere TIME_STD/TIME_DST (#968) - * Fix TLS MQTT SSL fingerprint test (#970, #808) - * Fix virtual relay status message used with Color/Dimmer control (#989) - * Fix command IRSend and IRHvac case sensitive parameter regression introduced with version 5.8.0 (#993) - * Fix pressure calculation for some BMP versions regression introduced with version 5.8.0i (#974) - * Fix Domoticz Dimmer set to same level not powering on (#945) - * Fix Blocked Loop when erasing large flash using command reset 2 (#1002) - * Fix relay power control when light power control is also configured as regression from 5.8.0 (#1016) - * Fix Mqtt server mDNS lookup only when MqttHost name is empty (#1026) - * Add debug information to MQTT subscribe - * Add translations to I2Cscan - * Add translation to BH1750 unit lx - * Add light scheme options (Color cycle Up, Down, Random) and moving WS2812 schemes up by 3 - * Add Domoticz counter sensor to IrReceive representing Received IR Protocol and Data - * Add option 0 to MqttHost to allow empty Mqtt host name - * Add support for Arilux AL-LC01 RGB Led controller (#370) - * Add esp8266 de-blocking to PubSubClient library (#790) - * Add Domoticz sensors for Voltage and Current (#903) - * Add platformio OTA upload support (#928, #934) - * Add warning to webpage when USE_MINIMAL is selected (#929) - * Add smoother movement of hour hand in WS2812 led clock (#936) - * Add support for Magic Home RGBW and some Arilux Led controllers (#940) - * Add command SetOption15 0 (default) for command PWM control or SetOption15 1 for commands Color/Dimmer control to PWM RGB(CW) leds (#941) - * Add Domoticz counter sensor to Sonoff Bridge representing Received RF code (#943) - * Add support for Luani HVIO board (https://luani.de/projekte/esp8266-hvio/) (#953) - * Add PWM initialization after restart (#955) - * Add IR Receiver support. Disable in user_config.h (#956) - * Add support for inverted PWM (#960) - * Add Sea level pressure calculation and Provide command Altitude (#974) - * Add support for up to 8 relays (#995) - * Add commands RfSync, RfLow, RfHigh, RfHost and RfCode to allow sending custom RF codes (#1001) - * Add retain to ENERGY messages controlled by command SensorRetain (#1013) - * Add commands Color2, Color3, Color4, Width2, Width3, Width4 and SetOption16 to set Ws2812 Clock parameters (#1019) - * Add German language file (#1022) - * Add support for connecting to MQTT brokers without userid and/or password (#1023) - * Add support for esp8266 core v2.4.0-rc2 (#1024) - * Add commands PwmRange 1,255..1023 and PwmFrequency 1,100..4000 (#1025) - * Add Polish language file (#1044, #1047) - * Add support for KMC 70011 Power Monitoring Smart Plug (#1045) - * Add support for VEML6070 I2C Ultra Violet level sensor (#1053) - * Add light turn Off Fade (#925) - * Add IrSend command option Panasonic as IrSend {"Protocol":"Panasonic", "Bits":16388, "Data":} - * where 16388 is 0x4004 hexadecimal (#1014) - * Add retry counter to DHT11/21/22 sensors (#1082) +- Rewrite code (partly) using Google C++ Style Guide (https://google.github.io/styleguide/cppguide.html) +- Rewrite code by using command lookup tables and javascript (client side) web page expansions +- Change HTML/CSS to enable nicer form field entry +- Change default PWM assignments for H801 RGB(CW) led controller to support optional Color/Dimmer control +- GPIO04 (W2) from GPIO_PWM2 to GPIO_USER to be user configurable for GPIO_PWM5 (second White - Warm if W1 is Cold) +- GPIO12 (Blue) GPIO_PWM3 no change +- GPIO13 (Green) from GPIO_PWM4 to GPIO_PWM2 +- GPIO14 (W1) from GPIO_PWM1 to GPIO_USER to be user configurable for GPIO_PWM4 (first White - Cold or Warm) +- GPIO15 (Red) from GPIO_PWM5 to GPIO_PWM1 +- Change default PWM assignments for MagicHome RGB(W) led controller to support optional Color/Dimmer control +- GPIO05 (Green) from GPIO_PWM4 to GPIO_PWM2 +- GPIO12 (Blue) from GPIO_PWM5 to GPIO_PWM3 +- GPIO13 (White) GPIO_USER to be user configurable for GPIO_PWM4 (White - Cold or Warm) +- GPIO14 (Red) from GPIO_PWM3 to GPIO_PWM1 +- Change default PWM assignment for Witty Cloud to support optional Color/Dimmer control (#976) +- GPIO12 (Green) from GPIO_PWM4 to GPIO_PWM2 +- GPIO13 (Blue) from GPIO_PWM5 to GPIO_PWM3 +- GPIO15 (Red) from GPIO_PWM3 to GPIO_PWM1 +- Change when another module is selected now all GPIO user configuration is removed +- Change command name IRRemote to IRSend (#956) +- Remove Arduino IDE version too low warning as it interferes with platformio.ini platform = espressif8266_stage +- Fix command FullTopic entry when using serial or console interface +- Fix possible UDP syslog blocking +- Fix minimum TelePeriod of 10 seconds set by web page +- Fix command GPIOx JSON response (#897) +- Fix inverted relay power on state (#909) +- Fix compile error when DOMOTICZ_UPDATE_TIMER is not defined (#930) +- Fix alignment of web page items in some browsers (#935) +- Fix setting all saved power settings to Off when SetOption0 (SaveState) = 0 (#955) +- Fix timezone range from -12/12 to -13/13 (#968) +- Fix Southern Hemisphere TIME_STD/TIME_DST (#968) +- Fix TLS MQTT SSL fingerprint test (#970, #808) +- Fix virtual relay status message used with Color/Dimmer control (#989) +- Fix command IRSend and IRHvac case sensitive parameter regression introduced with version 5.8.0 (#993) +- Fix pressure calculation for some BMP versions regression introduced with version 5.8.0i (#974) +- Fix Domoticz Dimmer set to same level not powering on (#945) +- Fix Blocked Loop when erasing large flash using command reset 2 (#1002) +- Fix relay power control when light power control is also configured as regression from 5.8.0 (#1016) +- Fix Mqtt server mDNS lookup only when MqttHost name is empty (#1026) +- Add debug information to MQTT subscribe +- Add translations to I2Cscan +- Add translation to BH1750 unit lx +- Add light scheme options (Color cycle Up, Down, Random) and moving WS2812 schemes up by 3 +- Add Domoticz counter sensor to IrReceive representing Received IR Protocol and Data +- Add option 0 to MqttHost to allow empty Mqtt host name +- Add support for Arilux AL-LC01 RGB Led controller (#370) +- Add esp8266 de-blocking to PubSubClient library (#790) +- Add Domoticz sensors for Voltage and Current (#903) +- Add platformio OTA upload support (#928, #934) +- Add warning to webpage when USE_MINIMAL is selected (#929) +- Add smoother movement of hour hand in WS2812 led clock (#936) +- Add support for Magic Home RGBW and some Arilux Led controllers (#940) +- Add command SetOption15 0 (default) for command PWM control or SetOption15 1 for commands Color/Dimmer control to PWM RGB(CW) leds (#941) +- Add Domoticz counter sensor to Sonoff Bridge representing Received RF code (#943) +- Add support for Luani HVIO board (https://luani.de/projekte/esp8266-hvio/) (#953) +- Add PWM initialization after restart (#955) +- Add IR Receiver support. Disable in user_config.h (#956) +- Add support for inverted PWM (#960) +- Add Sea level pressure calculation and Provide command Altitude (#974) +- Add support for up to 8 relays (#995) +- Add commands RfSync, RfLow, RfHigh, RfHost and RfCode to allow sending custom RF codes (#1001) +- Add retain to ENERGY messages controlled by command SensorRetain (#1013) +- Add commands Color2, Color3, Color4, Width2, Width3, Width4 and SetOption16 to set Ws2812 Clock parameters (#1019) +- Add German language file (#1022) +- Add support for connecting to MQTT brokers without userid and/or password (#1023) +- Add support for esp8266 core v2.4.0-rc2 (#1024) +- Add commands PwmRange 1,255..1023 and PwmFrequency 1,100..4000 (#1025) +- Add Polish language file (#1044, #1047) +- Add support for KMC 70011 Power Monitoring Smart Plug (#1045) +- Add support for VEML6070 I2C Ultra Violet level sensor (#1053) +- Add light turn Off Fade (#925) +- Add IrSend command option Panasonic as IrSend {"Protocol":"Panasonic", "Bits":16388, "Data":} +- where 16388 is 0x4004 hexadecimal (#1014) +- Add retry counter to DHT11/21/22 sensors (#1082) ### 5.8.0 20170918 - * Remove the need for NeoPixelBus library for Hue support - * Consolidate WS2812 into Sonoff Led for flexible future led strip library changes - * Invert WS2812 fade speed to align with Sonoff led (Speed 1 = fast, Speed 8 = slow) - * Remove upper case MQTT receive buffer - * Reduce code and string length for output of commands Modules and GPIOs - * Add Sonoff SC debug information - * Change syslog service - * Removed webserver syslog disable as now no longer needed - * Increased default MQTT message size from 368 to 405 bytes while keeping MQTT_MAX_PACKET_SIZE = 512 (because we can) - * Fix MQTT Offline or Remove MQTT retained topic code - * Fix Domoticz loop when Emulation is selected - * Add blink to WS2812 and Sonoff Led (#643) - * Add option WIFI_WAIT (5) to command WifiConfig to allow connection retry to same AP without restart or update flash (#772, #869) - * Add support for Witty Cloud (#794) - * Add GPIO14 to Sonoff Dual (#797, #839) - * Add support for Yunshan Wifi Relay (#802) - * Add GPIO16 input pulldown (#827) - * Add timeout to DHT and DS18B20 sensors (#852) - * Fix watchdog timeout caused by lack of stack space by moving to heap (#853) - * Allow LogPort and MqttPort up to 65535 and add LogPort tot Status 3 (#859) - * Allow command SwitchTopic in group mode (#861) - * Allow command SwitchMode if no switches are defined (#861) - * Add optional dimmer parameter to command Wakeup for WS2812, AiLight, Sonoff B1, Led and BN-SZ01 (#867) - * Fix basic On, Off, Toggle, Blink and BlinkOff commands when other language is selected (#874) +- Remove the need for NeoPixelBus library for Hue support +- Consolidate WS2812 into Sonoff Led for flexible future led strip library changes +- Invert WS2812 fade speed to align with Sonoff led (Speed 1 = fast, Speed 8 = slow) +- Remove upper case MQTT receive buffer +- Reduce code and string length for output of commands Modules and GPIOs +- Add Sonoff SC debug information +- Change syslog service +- Removed webserver syslog disable as now no longer needed +- Increased default MQTT message size from 368 to 405 bytes while keeping MQTT_MAX_PACKET_SIZE = 512 (because we can) +- Fix MQTT Offline or Remove MQTT retained topic code +- Fix Domoticz loop when Emulation is selected +- Add blink to WS2812 and Sonoff Led (#643) +- Add option WIFI_WAIT (5) to command WifiConfig to allow connection retry to same AP without restart or update flash (#772, #869) +- Add support for Witty Cloud (#794) +- Add GPIO14 to Sonoff Dual (#797, #839) +- Add support for Yunshan Wifi Relay (#802) +- Add GPIO16 input pulldown (#827) +- Add timeout to DHT and DS18B20 sensors (#852) +- Fix watchdog timeout caused by lack of stack space by moving to heap (#853) +- Allow LogPort and MqttPort up to 65535 and add LogPort tot Status 3 (#859) +- Allow command SwitchTopic in group mode (#861) +- Allow command SwitchMode if no switches are defined (#861) +- Add optional dimmer parameter to command Wakeup for WS2812, AiLight, Sonoff B1, Led and BN-SZ01 (#867) +- Fix basic On, Off, Toggle, Blink and BlinkOff commands when other language is selected (#874) ### 5.7.1 20170909 - * Remove leading spaces from MQTT data - * Fix webconsole special character entry - * Allow # as prefix for color value - * Fix Alexa detection and Hue App Update Request (#698, #854) +- Remove leading spaces from MQTT data +- Fix webconsole special character entry +- Allow # as prefix for color value +- Fix Alexa detection and Hue App Update Request (#698, #854) ### 5.7.0 20170907 - * Shrink module configuration webpage - * Fix settings order during startup to allow for displaying debug messages - * Fix some string length issues - * Add more string length tests by using strncpy - * Add Ai-Thinker RGBW led (AiLight) - * Add Power check and add PulseTime to power check at startup (#526) - * Add Supla Espablo support (#755) - * Add more precision to Sonoff Pow period and power results using command WattRes 0|1 (#759) - * Add basic internationalization and localization (#763) - * Add more Sonoff Pow range checking (#772) - * Fix invalid JSON (#786, #822) - * Add duplicate check to received RF signal within 2 seconds for Sonoff Bridge (#810) +- Shrink module configuration webpage +- Fix settings order during startup to allow for displaying debug messages +- Fix some string length issues +- Add more string length tests by using strncpy +- Add Ai-Thinker RGBW led (AiLight) +- Add Power check and add PulseTime to power check at startup (#526) +- Add Supla Espablo support (#755) +- Add more precision to Sonoff Pow period and power results using command WattRes 0|1 (#759) +- Add basic internationalization and localization (#763) +- Add more Sonoff Pow range checking (#772) +- Fix invalid JSON (#786, #822) +- Add duplicate check to received RF signal within 2 seconds for Sonoff Bridge (#810) ### 5.6.1 20170818 - * Change module list order in webpage - * Fix Sonoff T1 1CH and 2CH configuration (#751) +- Change module list order in webpage +- Fix Sonoff T1 1CH and 2CH configuration (#751) ### 5.6.0 20170818 - * Fix Sonoff Pow intermittent exception 0 - * Change Sonoff Pow sending Domoticz telemetry data only - * Add Ai-Thinker RGBW led (AiLight) (experimental) - * Add NeoPixelBus library to Sonoff Led for Hue support - * Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge - * Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676) - * Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color Temperature - * Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1 - * Add CT parameter to Hue - * Add Sonoff T1 support (#582) - * Add AnalogInput0 if configured as Analog Input to webpage (#697, #746) - * Add command SetOption14 0|1 to enable interlock mode (#719, #721) - * Fix Mitsubishi HVAC IR power controll (#740) +- Fix Sonoff Pow intermittent exception 0 +- Change Sonoff Pow sending Domoticz telemetry data only +- Add Ai-Thinker RGBW led (AiLight) (experimental) +- Add NeoPixelBus library to Sonoff Led for Hue support +- Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge +- Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676) +- Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color Temperature +- Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1 +- Add CT parameter to Hue +- Add Sonoff T1 support (#582) +- Add AnalogInput0 if configured as Analog Input to webpage (#697, #746) +- Add command SetOption14 0|1 to enable interlock mode (#719, #721) +- Fix Mitsubishi HVAC IR power controll (#740) ### 5.5.2 20170808 - * Extent max number of WS2812 pixels from 256 to 512 (#667) - * Add OTA handling if server responds with no update available (#695) - * Removed undocumented command FlashMode (#696) - * Fix compile time error message due to increased message buffer size (#703) +- Extent max number of WS2812 pixels from 256 to 512 (#667) +- Add OTA handling if server responds with no update available (#695) +- Removed undocumented command FlashMode (#696) +- Fix compile time error message due to increased message buffer size (#703) ### 5.5.1 20170805 - * Fix Sonoff Rf Bridge issues - * Add Sonoff RF Bridge MQTT messages on received and learned RF signal - * Add command VoltRes 0|1 to select voltage resolution to 0.1 V (#654) - * Add averaging to Analog input (#686) - * Add Energy tele data on Sonoff Pow Threshold change (#688) - * Fix inconsistent property names in Messages (#690) +- Fix Sonoff Rf Bridge issues +- Add Sonoff RF Bridge MQTT messages on received and learned RF signal +- Add command VoltRes 0|1 to select voltage resolution to 0.1 V (#654) +- Add averaging to Analog input (#686) +- Add Energy tele data on Sonoff Pow Threshold change (#688) +- Fix inconsistent property names in Messages (#690) ### 5.5.0 20170730 - * Reduce code space by removing the following commands as they are replaced by SetOption alternatives: - * SaveState = SetOption0 - * ButtonRestrict = SetOption1 - * Units = SetOption2 - * MQTT = SetOption3 - * MQTTResponse = SetOption4 - * TempUnit = SetOption8 - * Smoothing WS2812 animation poll, invert fade speed and max allowed wakeup time down to 3000 seconds - * Fix initial button press detection - * Add support for Sonoff RF Bridge 433 using command RfKey - * Fix regression from 5.0.7 by increasing message buffer size from 360 to 368 to accomodate 4 x DS18x20 sensors (#637) - * Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to send either ON/OFF or TOGGLE (#642) - * Adjust HLW calibration limits to accomodate HuaFan device and add commands HlwPSet, HlwUSet and HlwISet (#654) +- Reduce code space by removing the following commands as they are replaced by SetOption alternatives: +- SaveState = SetOption0 +- ButtonRestrict = SetOption1 +- Units = SetOption2 +- MQTT = SetOption3 +- MQTTResponse = SetOption4 +- TempUnit = SetOption8 +- Smoothing WS2812 animation poll, invert fade speed and max allowed wakeup time down to 3000 seconds +- Fix initial button press detection +- Add support for Sonoff RF Bridge 433 using command RfKey +- Fix regression from 5.0.7 by increasing message buffer size from 360 to 368 to accomodate 4 x DS18x20 sensors (#637) +- Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to send either ON/OFF or TOGGLE (#642) +- Adjust HLW calibration limits to accomodate HuaFan device and add commands HlwPSet, HlwUSet and HlwISet (#654) ### 5.4.0 20170725 - * Fix command reset regression introduced in 5.2.0 - * Increase polling from 0.1 second to 0.05 second - * Add multipress to all buttons - * Fix button 1 double press behaviour on multi relay devices - * Add support for Hua Fan Smart Socket (#479) - * Add support for Sonoff 4ch Pro (#565) - * Add command SetOption13 1 to allow immediate action on single button press - * (disables multipress, hold and unrestricted commands) (#587) +- Fix command reset regression introduced in 5.2.0 +- Increase polling from 0.1 second to 0.05 second +- Add multipress to all buttons +- Fix button 1 double press behaviour on multi relay devices +- Add support for Hua Fan Smart Socket (#479) +- Add support for Sonoff 4ch Pro (#565) +- Add command SetOption13 1 to allow immediate action on single button press +- (disables multipress, hold and unrestricted commands) (#587) ### 5.3.0 20170715 - * Major Hue rewrite which might introduce Alexa problems. If so, initiate an issue - * Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control to Hue - * Fix Sonoff Led Power, Dimmer and Color MQTT response (#176) - * Add commands Delay and Backlog to allow multiple commands at once separated by ";" (#593) - * Use default flashmode DOUT to solve restart hangs on esp8285 chips (#453, #598) - * Change Web console column width from 99 to 300 (#599) +- Major Hue rewrite which might introduce Alexa problems. If so, initiate an issue +- Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control to Hue +- Fix Sonoff Led Power, Dimmer and Color MQTT response (#176) +- Add commands Delay and Backlog to allow multiple commands at once separated by ";" (#593) +- Use default flashmode DOUT to solve restart hangs on esp8285 chips (#453, #598) +- Change Web console column width from 99 to 300 (#599) ### 5.2.4 20170703 - * Removed flash mode update after selecting different module solving esp8285 related problems - * Add device type flag to sonoff_template.ino - * Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led (#567) +- Removed flash mode update after selecting different module solving esp8285 related problems +- Add device type flag to sonoff_template.ino +- Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led (#567) ### 5.2.3 20170630 - * Change Sonoff Led color conversion code - * Fix SetOption12 handling - * Simplify auto configuration upgrade - * Add option Upgrade to only upgrade to any higher version (Old PR #213) - * Change FallbackTopic to cmnd// bypassing FullTopic and Prefix (#538) +- Change Sonoff Led color conversion code +- Fix SetOption12 handling +- Simplify auto configuration upgrade +- Add option Upgrade to only upgrade to any higher version (Old PR #213) +- Change FallbackTopic to cmnd// bypassing FullTopic and Prefix (#538) ### 5.2.2 20170625 - * Add configuration SaveAddress to Status 1 and Information Page - * Change Sonoff Led Color conversion from AtoH to strtol - * Fix possible wrong uploads due to configuration overwrites (#542) - * Fix payload negative numbers (#547) +- Add configuration SaveAddress to Status 1 and Information Page +- Change Sonoff Led Color conversion from AtoH to strtol +- Fix possible wrong uploads due to configuration overwrites (#542) +- Fix payload negative numbers (#547) ### 5.2.1 20170622 - * Fix Restore Configuration in case of lower version - * Revert auto configuration upgrade allowing easy upgrade which was removed in version 5.2.0 - * Fix config auto upgrade from versions below version 4.1.1 (#530) +- Fix Restore Configuration in case of lower version +- Revert auto configuration upgrade allowing easy upgrade which was removed in version 5.2.0 +- Fix config auto upgrade from versions below version 4.1.1 (#530) ### 5.2.0 20170619 - * Add command SetOption12 1 to disable newly released configuration flash rotate to reduce flash wear - * Fix command CounterDebounce by removing test for active GPIO (#524) - * Add command SetOption33 1..250 to allow user configure POW Max_Power_Retry count (#525) +- Add command SetOption12 1 to disable newly released configuration flash rotate to reduce flash wear +- Fix command CounterDebounce by removing test for active GPIO (#524) +- Add command SetOption33 1..250 to allow user configure POW Max_Power_Retry count (#525) ### 5.1.7 20170616 - * Prep removal of SetOptions alternatives - * Restore webpage upgrade error messages removed in 5.1.5 - * Add hold button functionality to buttons 2 to 4 - * Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds to 10 seconds (#200) - * Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507) - * Changed webpage form actions from post to get and use relative path url (#434, #522) +- Prep removal of SetOptions alternatives +- Restore webpage upgrade error messages removed in 5.1.5 +- Add hold button functionality to buttons 2 to 4 +- Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds to 10 seconds (#200) +- Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507) +- Changed webpage form actions from post to get and use relative path url (#434, #522) ### 5.1.6 20170606 - * Shrink code - * Removed online configuration of Domoticz In and Domoticz Out MQTT strings - * Removed commands DomoticzInTopic and DomoticzOutTopic - * Add define KEY_HOLD_TIME to configure button hold threshold before sending MQTT Hold message - * Add command StateText4 to configure button MQTT Hold text (= MQTT_CMND_HOLD) - * Add command SetOption11 0|1 to swap pushbutton single and double press functionality (#200) - * Add command SwitchMode 5 (PUSHBUTTONHOLD) and 6 (PUSHBUTTONHOLD_INV) (#489) +- Shrink code +- Removed online configuration of Domoticz In and Domoticz Out MQTT strings +- Removed commands DomoticzInTopic and DomoticzOutTopic +- Add define KEY_HOLD_TIME to configure button hold threshold before sending MQTT Hold message +- Add command StateText4 to configure button MQTT Hold text (= MQTT_CMND_HOLD) +- Add command SetOption11 0|1 to swap pushbutton single and double press functionality (#200) +- Add command SwitchMode 5 (PUSHBUTTONHOLD) and 6 (PUSHBUTTONHOLD_INV) (#489) ### 5.1.5 20170604 - * Shrink code in preparation to ESP8266-Arduino 2.4.0-rc1 - * Add effect parameter to HUE Device (#464) +- Shrink code in preparation to ESP8266-Arduino 2.4.0-rc1 +- Add effect parameter to HUE Device (#464) ### 5.1.4 20170601 - * Removed pre-compiled versions from repository as they are available within the release - * Changed HUE Device type to color supporting version (#464) - * Fix compile error when BE_MINIMAL is selected (#467, #476) - * Add multiple compiled versions to release using updated Travis script and platformio.ini (#467) +- Removed pre-compiled versions from repository as they are available within the release +- Changed HUE Device type to color supporting version (#464) +- Fix compile error when BE_MINIMAL is selected (#467, #476) +- Add multiple compiled versions to release using updated Travis script and platformio.ini (#467) ### 5.1.3 20170520 - * Add Domoticz Counter +- Add Domoticz Counter ### 5.1.2 20170519 - * Fix Counter/Timer JSON message and update Counter/Timer on webpage - * Fix WS2812 Domoticz related regression issues +- Fix Counter/Timer JSON message and update Counter/Timer on webpage +- Fix WS2812 Domoticz related regression issues ### 5.1.1 20170517 - * Allow command FullTopic in group mode - * Prepare for more use of RTC memory - * Add independant WS2812 led string power control (#386, #390) - * Add command Counter to control up to four GPIO falling edge interrupt counters or timers (#459) - * Add command CounterType to select between pulse counting or pulse timing - * Add command CounterDebounce to select global counter debounce time in mSec +- Allow command FullTopic in group mode +- Prepare for more use of RTC memory +- Add independant WS2812 led string power control (#386, #390) +- Add command Counter to control up to four GPIO falling edge interrupt counters or timers (#459) +- Add command CounterType to select between pulse counting or pulse timing +- Add command CounterDebounce to select global counter debounce time in mSec ### 5.1.0 20170513 - * Fix Offline/Removal of retained topic when FullTopic is changed - * Add FullTopic to MQTT Configuration and Information web pages - * Add license model GPLv3 (#188) +- Fix Offline/Removal of retained topic when FullTopic is changed +- Add FullTopic to MQTT Configuration and Information web pages +- Add license model GPLv3 (#188) ### 5.0.7 20170511 - * Fix possible exception 28 on empty command - * Add command SetOption0 as replacement for SaveState - * Add command SetOption1 as replacement for ButtonRestrict - * Add command SetOption2 as replacement for Units - * Add command SetOption4 as replacement for MqttResponse - * Add command SetOption8 as replacement for TempUnit - * Add command SetOption10 On|Off to select between Offline or Removing previous retained topic (#417, #436) +- Fix possible exception 28 on empty command +- Add command SetOption0 as replacement for SaveState +- Add command SetOption1 as replacement for ButtonRestrict +- Add command SetOption2 as replacement for Units +- Add command SetOption4 as replacement for MqttResponse +- Add command SetOption8 as replacement for TempUnit +- Add command SetOption10 On|Off to select between Offline or Removing previous retained topic (#417, #436) ### 5.0.6 20170510 - * Remove hyphen in case of a single DHT sensor connected (#427) - * Add command MqttRetry to change default MQTT reconnect retry timer from minimal 10 seconds (#429) +- Remove hyphen in case of a single DHT sensor connected (#427) +- Add command MqttRetry to change default MQTT reconnect retry timer from minimal 10 seconds (#429) ### 5.0.5 20170508 - * Add command FullTopic with tokens %topic% (replaced by command Topic value) and - * %prefix% (replaced by command Prefix values) for more flexible topic definitions (#244) - * See wiki > MQTT Features https://github.com/arendst/Tasmota/wiki/MQTT-Features for more information +- Add command FullTopic with tokens %topic% (replaced by command Topic value) and +- %prefix% (replaced by command Prefix values) for more flexible topic definitions (#244) +- See wiki > MQTT Features https://github.com/arendst/Tasmota/wiki/MQTT-Features for more information ### 5.0.4 20170505 - * Add Sonoff Pow Energy Total up to 40 MWh - * Add command EnergyReset 1|2|3 to reset Energy counters (#406) - * Fix Domoticz Energy logging (#411) - * Add command PowerOnState 4 to keep relay always on and disabling all power control (#418) +- Add Sonoff Pow Energy Total up to 40 MWh +- Add command EnergyReset 1|2|3 to reset Energy counters (#406) +- Fix Domoticz Energy logging (#411) +- Add command PowerOnState 4 to keep relay always on and disabling all power control (#418) ### 5.0.3 20170504 - * Add command SensorRetain on|off to enable retaining of mqtt message tele/sonoff/SENSOR (#74) - * Change WifiConfig timeout from 60 seconds to 180 seconds (#212) - * Change Sonoff Touch command Ledstate functionality by turning led on if power is off (#214) - * Add 4 seconds delay after power on before enabling button to workaround Wemos D1 mini RTS circuit (#380) +- Add command SensorRetain on|off to enable retaining of mqtt message tele/sonoff/SENSOR (#74) +- Change WifiConfig timeout from 60 seconds to 180 seconds (#212) +- Change Sonoff Touch command Ledstate functionality by turning led on if power is off (#214) +- Add 4 seconds delay after power on before enabling button to workaround Wemos D1 mini RTS circuit (#380) ### 5.0.2 20170503 - * Reset SaveData, SaveState and MqttResponse to default values due to rearranging settings - * Moved some settings to flag area - * Add command TempUnit Celsius|Fahrenheit for selecting Celsius or Fahrenheit (#347) - * Add command TempRes 0..3 for selecting Temperature Resolution (#347) - * Add command HumRes 0..3 for selecting Humidity Resolution (#347) - * Add command PressRes 0..3 for selecting Pressure Resolution (#347) - * Add command EnergyRes 0..5 for selecting Energy Resolution (#347) - * Add "TempUnit":"C|F" to sensor JSON output (#347) - * Add support for up to three DHT type sensors each using a different GPIO (#339, #404) +- Reset SaveData, SaveState and MqttResponse to default values due to rearranging settings +- Moved some settings to flag area +- Add command TempUnit Celsius|Fahrenheit for selecting Celsius or Fahrenheit (#347) +- Add command TempRes 0..3 for selecting Temperature Resolution (#347) +- Add command HumRes 0..3 for selecting Humidity Resolution (#347) +- Add command PressRes 0..3 for selecting Pressure Resolution (#347) +- Add command EnergyRes 0..5 for selecting Energy Resolution (#347) +- Add "TempUnit":"C|F" to sensor JSON output (#347) +- Add support for up to three DHT type sensors each using a different GPIO (#339, #404) ### 5.0.1 20170429 - * Adjust Sonoff SC messages to prepare for display feature - * Move static data from RAM to Flash - * Fix PowerOnState for some devices not reporting "Power on" state (#284, #380, #383) +- Adjust Sonoff SC messages to prepare for display feature +- Move static data from RAM to Flash +- Fix PowerOnState for some devices not reporting "Power on" state (#284, #380, #383) ### 5.0.0 20170425 - * Memory status message update - * Fix setting migration to better preserve settings during move (#382) - * Best practice is first doing a Backup Configuration before installing version 5.0.0 - * Reset save count after setting move - * Start using new linker script without SPIFFS +- Memory status message update +- Fix setting migration to better preserve settings during move (#382) +- Best practice is first doing a Backup Configuration before installing version 5.0.0 +- Reset save count after setting move +- Start using new linker script without SPIFFS ### 4.2.0 20170424 - * Prepare for SPIFFS removal by moving settings to EEPROM area - * Fix compilation error when webserver is disabled (#378) +- Prepare for SPIFFS removal by moving settings to EEPROM area +- Fix compilation error when webserver is disabled (#378) ### 4.1.3 20170410 - * Add user configuarble GPIO to module S20 Socket and Slampher - * Add support for Sonoff SC (#112) - * Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led firmware (#122) - * Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions due to power supply instabilities (#122) - * Add Access Point Mac Address to Status 11 and Telemetry (#329) - * Fix DS18B20 negative temperature readings (#334) +- Add user configuarble GPIO to module S20 Socket and Slampher +- Add support for Sonoff SC (#112) +- Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led firmware (#122) +- Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions due to power supply instabilities (#122) +- Add Access Point Mac Address to Status 11 and Telemetry (#329) +- Fix DS18B20 negative temperature readings (#334) ### 4.1.2 20170403 - * Rename Unrecognised command to Unknown command - * Remove all command lists - * Remove command SmartConfig (superseded by WifiConfig) - * Fix boot loop when selecting module Sonoff 4CH or Sonoff Touch on non ESP8285 hardware - * Add optional support for Toshiba and Mitsubishi HVAC IR control (needs updated IRremote8266 library) (#83, #257) - * Add all configured switches to Domoticz Configuration web page (#305) - * Fix compile error when selecting WS2812 DMA (#313) +- Rename Unrecognised command to Unknown command +- Remove all command lists +- Remove command SmartConfig (superseded by WifiConfig) +- Fix boot loop when selecting module Sonoff 4CH or Sonoff Touch on non ESP8285 hardware +- Add optional support for Toshiba and Mitsubishi HVAC IR control (needs updated IRremote8266 library) (#83, #257) +- Add all configured switches to Domoticz Configuration web page (#305) +- Fix compile error when selecting WS2812 DMA (#313) ### 4.1.1 20170329 - * Fix default Telemetry for command Prefix3 - * Fix webserver Module parameters for disabled select - * Fix sensor status for enabled switches - * Remove Light as alternative for Power (save code space) - * Remove migration option from pre V3 (code cleanup) - * Remove unofficial SPIFFS support (code cleanup) - * Remove command list when unknown command is entered (save code space) - * Rename Status11 json from StatusPWR to unique StatusSTS - * Rename command Gateway to IPAddres2, Subnetmask to IPAddress3 and DnsServer to IPAddress4 (save code space) - * Add Command MqttResponse to select either command or RESULT topic as response (#258) - * Add command StateText1 to StateText3 to assign MQTT_STATUS_OFF, MQTT_STATUS_ON and MQTT_CMND_TOGGLE respectively (#286) - * Remove restart after IPAddress changes (#292) - * Add support for MAX31850 in xsns_ds18x20.ino (#295) - * Fix possible uptime update misses (#302) +- Fix default Telemetry for command Prefix3 +- Fix webserver Module parameters for disabled select +- Fix sensor status for enabled switches +- Remove Light as alternative for Power (save code space) +- Remove migration option from pre V3 (code cleanup) +- Remove unofficial SPIFFS support (code cleanup) +- Remove command list when unknown command is entered (save code space) +- Rename Status11 json from StatusPWR to unique StatusSTS +- Rename command Gateway to IPAddres2, Subnetmask to IPAddress3 and DnsServer to IPAddress4 (save code space) +- Add Command MqttResponse to select either command or RESULT topic as response (#258) +- Add command StateText1 to StateText3 to assign MQTT_STATUS_OFF, MQTT_STATUS_ON and MQTT_CMND_TOGGLE respectively (#286) +- Remove restart after IPAddress changes (#292) +- Add support for MAX31850 in xsns_ds18x20.ino (#295) +- Fix possible uptime update misses (#302) ### 4.1.0 20170325 - * Change static IP addresses in user_config.h from list (using commas) to string (using dots) - * Unify display result of commands Modules, Module and Gpios - * Rewrite Module selection web page to bring size down from 18651 to 4319 bytes (!) (#234, #240) - * Add basic support for (Lixada) H801 RGBWW controller (#252) - * Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and PUB_PREFIX2 respectively (#255) - * Add static ip addresses to flash (#262) - * Add commands IpAddress, Gateway, Subnetmask and DnsServer to select static ip addresses (#273) +- Change static IP addresses in user_config.h from list (using commas) to string (using dots) +- Unify display result of commands Modules, Module and Gpios +- Rewrite Module selection web page to bring size down from 18651 to 4319 bytes (!) (#234, #240) +- Add basic support for (Lixada) H801 RGBWW controller (#252) +- Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and PUB_PREFIX2 respectively (#255) +- Add static ip addresses to flash (#262) +- Add commands IpAddress, Gateway, Subnetmask and DnsServer to select static ip addresses (#273) ### 4.0.8 20170321 - * Fix entering non-numeric webpassword - * Force selection between TLS or Webserver due to memory restraint (#240) - * Allow entering empty string using "0" for selected commands (#242) - * Fix exception when posting commands to web console containing % (#250) +- Fix entering non-numeric webpassword +- Force selection between TLS or Webserver due to memory restraint (#240) +- Allow entering empty string using "0" for selected commands (#242) +- Fix exception when posting commands to web console containing % (#250) ### 4.0.7 20170319 - * Increased Sonoff Led PWM frequency from 432 to 1000 - * Fix possible watch dog reboot after changing module type on web page - * Fix reporting of GPIO usage from web page - * Fix Sonoff Led blank during firmware upgrade - * Fix Sonoff Led flicker and possible flash corruption by using latest Arduino-esp8266 versions - * of pwm core files included in sonoff library (#211) - * Add PWM output control with commands PWM1 to PWM5 using user selectable GPIOs (#211) - * Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal (1000) and HlwICal (2500) (#223) - * Add Switch state to sensor status (#227, #233) - * Add user configuarble GPIO to module Sonoff Touch (#228) - * Add define WEB_PORT to user_config.h to change default web server port from 80 (#232) - * Fix failed Ota Firmware upgrade started from Web page (#235) +- Increased Sonoff Led PWM frequency from 432 to 1000 +- Fix possible watch dog reboot after changing module type on web page +- Fix reporting of GPIO usage from web page +- Fix Sonoff Led blank during firmware upgrade +- Fix Sonoff Led flicker and possible flash corruption by using latest Arduino-esp8266 versions +- of pwm core files included in sonoff library (#211) +- Add PWM output control with commands PWM1 to PWM5 using user selectable GPIOs (#211) +- Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal (1000) and HlwICal (2500) (#223) +- Add Switch state to sensor status (#227, #233) +- Add user configuarble GPIO to module Sonoff Touch (#228) +- Add define WEB_PORT to user_config.h to change default web server port from 80 (#232) +- Fix failed Ota Firmware upgrade started from Web page (#235) ### 4.0.6 20170316 - * Fix to better find device by Wifi hostname - * Fix compile error when some I2C devices are disabled - * Add (experimental) support for SHT1X emulating I2C (#97) - * Add ADC to ElectroDragon (#203) - * Add support for Sonoff Dev (#206) +- Fix to better find device by Wifi hostname +- Fix compile error when some I2C devices are disabled +- Add (experimental) support for SHT1X emulating I2C (#97) +- Add ADC to ElectroDragon (#203) +- Add support for Sonoff Dev (#206) ### 4.0.5 20170314 - * Add command Status 11 to show power status with Vcc if define USE_ADC_VCC is enabled (default) - * Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with define USE_ADC_VCC disabled (#137) - * Add MQTT host:port to timeout message (#199) +- Add command Status 11 to show power status with Vcc if define USE_ADC_VCC is enabled (default) +- Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with define USE_ADC_VCC disabled (#137) +- Add MQTT host:port to timeout message (#199) ### 4.0.4 20170312 - * Add pulse timers for up to 4 relays (#106) - * Fix Sonoff Led power state when dimmer or color is 0 (#176) - * Add command NtpServer to configure up to three NTP servers (#177) - * Delete module User Test as module Wemos D1 mini has same/more user configurable GPIO (#178) - * Add more user configurable GPIO to module ElectroDragon (#183) +- Add pulse timers for up to 4 relays (#106) +- Fix Sonoff Led power state when dimmer or color is 0 (#176) +- Add command NtpServer to configure up to three NTP servers (#177) +- Delete module User Test as module Wemos D1 mini has same/more user configurable GPIO (#178) +- Add more user configurable GPIO to module ElectroDragon (#183) ### 4.0.3 20170309 - * Renamed Module NodeMCU to WeMos D1 mini - * Add GPIO1 as user option to some modules - * Add Buttons, Relays and Leds to user configurable options (#159) - * Add description on Module parameters web page to some well known GPIOs (#107, #171) +- Renamed Module NodeMCU to WeMos D1 mini +- Add GPIO1 as user option to some modules +- Add Buttons, Relays and Leds to user configurable options (#159) +- Add description on Module parameters web page to some well known GPIOs (#107, #171) ### 4.0.2 20170308 - * Restore correct seriallog level after Serial logging was disabled - * Add simple dimmer slider to Sonoff Led web page - * Reduced root webpage size by 31% - * Expand Status 2 with Build date/time and core version - * Fix webserver redirection when not in WifiManager mode (#156) - * Add command ButtonRestrict On/Off to restrict access to button hold and button multi press options above 2 (#161) - * Fix DS18S20 negative temperature readings (#165) - * Fix crlf compilation error due to bad syntax (#144, #167) +- Restore correct seriallog level after Serial logging was disabled +- Add simple dimmer slider to Sonoff Led web page +- Reduced root webpage size by 31% +- Expand Status 2 with Build date/time and core version +- Fix webserver redirection when not in WifiManager mode (#156) +- Add command ButtonRestrict On/Off to restrict access to button hold and button multi press options above 2 (#161) +- Fix DS18S20 negative temperature readings (#165) +- Fix crlf compilation error due to bad syntax (#144, #167) ### 4.0.1 20170305 - * Fix char default sizes and set MESSZ to 360 (#143) - * Fix SerialLog setting status - * Disable syslog when emulation is active - * Add DS18B20 web page display refresh +- Fix char default sizes and set MESSZ to 360 (#143) +- Fix SerialLog setting status +- Disable syslog when emulation is active +- Add DS18B20 web page display refresh ### 4.0.0 20170303 - * Add define to remove config migration code for versions below 3.0 (See Wiki-Upgrade-Migration path) - * Free memory by switching from String to char[] - * Raised Sonoff Led PWM frequency from 200Hz to 432Hz in search of stability (hardware watchdog timeouts) (#122) - * Increase message size and suggested minimum MQTT_MAX_PACKET_SIZE to 512 (#114, #124) - * Remove runtime warning message regarding MQTT_MAX_PACKET_SIZE too small as it is now moved to compile time (#124) - * Fix possible panics with web console and http commands while UDP syslog is active (#127) - * Add optional static IP address (#129) - * Add define ENERGY_RESOLUTION in user_config.h to allow user control over precision (#136) +- Add define to remove config migration code for versions below 3.0 (See Wiki-Upgrade-Migration path) +- Free memory by switching from String to char[] +- Raised Sonoff Led PWM frequency from 200Hz to 432Hz in search of stability (hardware watchdog timeouts) (#122) +- Increase message size and suggested minimum MQTT_MAX_PACKET_SIZE to 512 (#114, #124) +- Remove runtime warning message regarding MQTT_MAX_PACKET_SIZE too small as it is now moved to compile time (#124) +- Fix possible panics with web console and http commands while UDP syslog is active (#127) +- Add optional static IP address (#129) +- Add define ENERGY_RESOLUTION in user_config.h to allow user control over precision (#136) ### 3.9.22 20170228 - * Update web console - * Fix Status 4 JSON message - * Add Exception info during restart if available - * Add osWatch service to detect loop hangs that might happen during (OTA) upgrades - * Add WiOn support for relay and switch only (#82, #102) - * Allow for user specified relay count up to four in sonoff_template.h (#109) - * Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021 (#118) - * Add NodeMCU or Wemos configuration option (#119) +- Update web console +- Fix Status 4 JSON message +- Add Exception info during restart if available +- Add osWatch service to detect loop hangs that might happen during (OTA) upgrades +- Add WiOn support for relay and switch only (#82, #102) +- Allow for user specified relay count up to four in sonoff_template.h (#109) +- Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021 (#118) +- Add NodeMCU or Wemos configuration option (#119) ### 3.9.21 20170224 - * Add ajax to web root page and web console (#79) - * Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84, #88) - * Fix MQTT upgrade when webserver is active +- Add ajax to web root page and web console (#79) +- Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84, #88) +- Fix MQTT upgrade when webserver is active ### 3.9.20 20170221 - * Add minimal basic authentication to Web Admin mode (#87) - * Fix Hue and add HSB support (#89) +- Add minimal basic authentication to Web Admin mode (#87) +- Fix Hue and add HSB support (#89) ### 3.9.19 20170219 - * Sonoff Led: Made GPIO04, 05 and 15 available for user - * Sonoff Led: Add commands Fade, Speed, WakupDuration, Wakeup and LedTable +- Sonoff Led: Made GPIO04, 05 and 15 available for user +- Sonoff Led: Add commands Fade, Speed, WakupDuration, Wakeup and LedTable ### 3.9.18 20170218 - * Fix ledstate 0 to turn off led - * Fix Sonoff Led dimmer range (#16) - * Change Sonoff Led command Dimmer to act on both cold and warm color - * Add Sonoff Led command Color CCWW where CCWW are hexadecimal values fro 00 - FF - * Reduce Sonoff Led flickering by disabling interrupts during flash save and disabling - * Led during OTA upgrade and Web upload (#16) +- Fix ledstate 0 to turn off led +- Fix Sonoff Led dimmer range (#16) +- Change Sonoff Led command Dimmer to act on both cold and warm color +- Add Sonoff Led command Color CCWW where CCWW are hexadecimal values fro 00 - FF +- Reduce Sonoff Led flickering by disabling interrupts during flash save and disabling +- Led during OTA upgrade and Web upload (#16) ### 3.9.17 20170217 - * Fix possible ArduinoJSON related memory fragmentation - * Changed console logging using less memory - * Add GPIO04 as user selectable for Sonoff Dual (#75) +- Fix possible ArduinoJSON related memory fragmentation +- Changed console logging using less memory +- Add GPIO04 as user selectable for Sonoff Dual (#75) ### 3.9.16 20170214 - * Update latching relay handler - * Add support for IR led using IRremoteESP8266 library (#59) - * Add Hue argument passing using ArduinoJSON library (#59) +- Update latching relay handler +- Add support for IR led using IRremoteESP8266 library (#59) +- Add Hue argument passing using ArduinoJSON library (#59) ### 3.9.15 20170213 - * Change JSON float values from string to number according to http://json.org (#56) - * Add support for exs latched relay module https://ex-store.de/ESP8266-WiFi-Relay-V31 (#58) - * Add support for inverted relays - * Changed MAX_LOG_LINES from 70 to 60 to preserve memory +- Change JSON float values from string to number according to http://json.org (#56) +- Add support for exs latched relay module https://ex-store.de/ESP8266-WiFi-Relay-V31 (#58) +- Add support for inverted relays +- Changed MAX_LOG_LINES from 70 to 60 to preserve memory ### 3.9.14 20170211 - * Add False and True as alternatives for 0/Off and 1/On (#49) - * Fix Status10 JSON format (#52) - * Fix DS18x20 using OneWire library (#53) +- Add False and True as alternatives for 0/Off and 1/On (#49) +- Fix Status10 JSON format (#52) +- Fix DS18x20 using OneWire library (#53) ### 3.9.13 20170210 - * Add FlashChipMode to Status 4 - * Removed redundant DHT2 option and code - * Add Sonoff SV GPIO pin 05 configuration (#40) - * Add configuration file backup and restore via web page - * Fix latency due to light_sleep mode even if sleep was set to zero (#50) +- Add FlashChipMode to Status 4 +- Removed redundant DHT2 option and code +- Add Sonoff SV GPIO pin 05 configuration (#40) +- Add configuration file backup and restore via web page +- Fix latency due to light_sleep mode even if sleep was set to zero (#50) ### 3.9.12 20170208 - * Fix compile error when webserver is disabled (#30) - * Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during OTA upload - * Fix hostname issues by not allowing user entry of string formatting and removing from user_config.h (#36) +- Fix compile error when webserver is disabled (#30) +- Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during OTA upload +- Fix hostname issues by not allowing user entry of string formatting and removing from user_config.h (#36) ### 3.9.11 20170204 - * Fix command I2Cscan - * Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic - * Make all TELEMETRY, STATUS and COMMAND message topics unique (#4) - * Advertise command topic to be used by iobroker (#299) - * Fix butten (non)detection if no GPIO_KEY1 is defined (#13) - * Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars (#18) - * Update web page with Build Date/Time, Emulation and mDNS Discovery and Advertise information (#21) +- Fix command I2Cscan +- Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic +- Make all TELEMETRY, STATUS and COMMAND message topics unique (#4) +- Advertise command topic to be used by iobroker (#299) +- Fix butten (non)detection if no GPIO_KEY1 is defined (#13) +- Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars (#18) +- Update web page with Build Date/Time, Emulation and mDNS Discovery and Advertise information (#21) ### 3.9.10 20170130 - * Add WS2812 Color Type selection (RGB or GRB) to user_config.h (#7) - * Hue api changes to support HUE App(s) (#8) +- Add WS2812 Color Type selection (RGB or GRB) to user_config.h (#7) +- Hue api changes to support HUE App(s) (#8) ### 3.9.9 20170130 - * Add command status 10 showing sensor data - * Fix hlw status messages if hlw is disabled +- Add command status 10 showing sensor data +- Fix hlw status messages if hlw is disabled ### 3.9.8 20170130 - * Remove GPIO07 and GPIO08 from user selectable (#5) +- Remove GPIO07 and GPIO08 from user selectable (#5) ### 3.9.7 20170129 - * Fix possible WS2812 exceptions when using emulation - * Add command Emulation to dynamic configure Belkin WeMo and Hue Bridge for Alexa +- Fix possible WS2812 exceptions when using emulation +- Add command Emulation to dynamic configure Belkin WeMo and Hue Bridge for Alexa ### 3.9.6 20170129 - * Add dynamic sleep for WS2812 animation (#1) +- Add dynamic sleep for WS2812 animation (#1) ### 3.9.5 20170128 - * Fix error message in case of wrong Domoticz command +- Fix error message in case of wrong Domoticz command ### 3.9.4 20170127 - * Fix Sonoff Dual Relay switching (#287) +- Fix Sonoff Dual Relay switching (#287) ### 3.9.3 20170127 - * Add confirmation before Restart via webpage - * Expand Domoticz Configuration webpage with Key, Switch and Sensor Index and - * add commands DomoticzSwitchIdx and DomoticzSensorIdx (#86) (#174) (#219) - * Fix default DHT11 sensor driver selection - * Fix LedPower status after button press (#279) - * Add command Sleep 0 - 250 mSec for optional light sleep mode to lower energy consumption (#272) - * (Expect overall button/key/switch misses and wrong values on Sonoff Pow) - * Add Hue brightness extension (#281) - * Fix Hue brightness and change to call by reference (#283) +- Add confirmation before Restart via webpage +- Expand Domoticz Configuration webpage with Key, Switch and Sensor Index and +- add commands DomoticzSwitchIdx and DomoticzSensorIdx (#86) (#174) (#219) +- Fix default DHT11 sensor driver selection +- Fix LedPower status after button press (#279) +- Add command Sleep 0 - 250 mSec for optional light sleep mode to lower energy consumption (#272) +- (Expect overall button/key/switch misses and wrong values on Sonoff Pow) +- Add Hue brightness extension (#281) +- Fix Hue brightness and change to call by reference (#283) ### 3.9.2 20170124 - * Add confirmation before Reset Configuration via webpage (#244) - * Add WS2812 features (see Wiki commands) +- Add confirmation before Reset Configuration via webpage (#244) +- Add WS2812 features (see Wiki commands) ### 3.9.1 20170124 - * Change PowerOnState function to only trigger when Power On (and not just restart) (#238) - * Move HLW interrupts back to RAM and make WS2812_DMA optional as it generates Exception on Pow (#264) - * Add charset=utf-8 to webpages (#266) - * Update Hue emulation (#268) - * Fix status module number - * Add support for domoticz Dimmer on Sonoff_Led and WS2812 - * Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during web upload +- Change PowerOnState function to only trigger when Power On (and not just restart) (#238) +- Move HLW interrupts back to RAM and make WS2812_DMA optional as it generates Exception on Pow (#264) +- Add charset=utf-8 to webpages (#266) +- Update Hue emulation (#268) +- Fix status module number +- Add support for domoticz Dimmer on Sonoff_Led and WS2812 +- Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during web upload ### 3.2.6a 20170120 - * Fix Sonoff Pow compile error (#255) - * Move HLW interrupts back to ROM (Needed for WS2812 DMA interrupts) - * Removed all IO config from user_config.h as this will be done by commands or webpage - * Removed MessageFormat and supports JSON only except POWER/LIGHT status - * Add command LedPower to control main led (#247) - * Add more FriendlyNames for Hue (#254) - * Add DMA support for WS2812 when using pin 3 while other pins work just as well in my case... - * Add HUE emulation for Alexa (#229) - * Add basic WS2812 support (#229) - * Fix Wemo when MQTT is disabled (#245) - * Revert ButtonTopic and change SwitchTopic1 - 4 to one SwitchTopic - * Rename MqttUnits to Units - * Add Mqtt command to enable/disable MQTT +- Fix Sonoff Pow compile error (#255) +- Move HLW interrupts back to ROM (Needed for WS2812 DMA interrupts) +- Removed all IO config from user_config.h as this will be done by commands or webpage +- Removed MessageFormat and supports JSON only except POWER/LIGHT status +- Add command LedPower to control main led (#247) +- Add more FriendlyNames for Hue (#254) +- Add DMA support for WS2812 when using pin 3 while other pins work just as well in my case... +- Add HUE emulation for Alexa (#229) +- Add basic WS2812 support (#229) +- Fix Wemo when MQTT is disabled (#245) +- Revert ButtonTopic and change SwitchTopic1 - 4 to one SwitchTopic +- Rename MqttUnits to Units +- Add Mqtt command to enable/disable MQTT ### 3.2.2a 20170115 - * Add dynamic (Sonoff) Module, user GPIO and sensor selection (one size fits (almost) all) - * Add support for Sonoff LED - * Add Seriallog disable after 600 seconds for Sonoff Dual and 4 Channel - * Add ButtonTopic2 - 4, SwitchTopic1 - 4 and SwitchRetain +- Add dynamic (Sonoff) Module, user GPIO and sensor selection (one size fits (almost) all) +- Add support for Sonoff LED +- Add Seriallog disable after 600 seconds for Sonoff Dual and 4 Channel +- Add ButtonTopic2 - 4, SwitchTopic1 - 4 and SwitchRetain ### 3.2.2 20170113 - * Fix PowerOnState 2 functionality after re-applying power (#230) +- Fix PowerOnState 2 functionality after re-applying power (#230) ### 3.2.1 20170113 - * Fix some failed command decoding (#228) - * Removed passwords from status messages (#216) +- Fix some failed command decoding (#228) +- Removed passwords from status messages (#216) ### 3.2.0 20170111 - * Add I2C BH1750 sensor (#222) - * Sensor rewrite preparing for online selection +- Add I2C BH1750 sensor (#222) +- Sensor rewrite preparing for online selection ### 3.1.16 20170109 - * Fix Domoticz possible error condition - * Remove Wifi password from connection message (#216) - * Add Configure Other menu item to web page (#209) - * Add command FriendlyName, field Friendly Name and define FRIENDLY_NAME to be used by Alexa - * eliminating current use of MQTT_CLIENT_ID (#209) - * Add friendlyname to webpage replacing former hostname +- Fix Domoticz possible error condition +- Remove Wifi password from connection message (#216) +- Add Configure Other menu item to web page (#209) +- Add command FriendlyName, field Friendly Name and define FRIENDLY_NAME to be used by Alexa +- eliminating current use of MQTT_CLIENT_ID (#209) +- Add friendlyname to webpage replacing former hostname ### 3.1.15 20170108 - * Fix Domoticz send key regression with Toggle command +- Fix Domoticz send key regression with Toggle command ### 3.1.14 20170107 - * Add support for command TOGGLE (define MQTT_CMND_TOGGLE) when ButtonTopic is in use and not equal to Topic (#207) +- Add support for command TOGGLE (define MQTT_CMND_TOGGLE) when ButtonTopic is in use and not equal to Topic (#207) ### 3.1.13 20170107 - * Fix web console command input when SUB_PREFIX contains '/' (#152) - * Add command response to web command (#200) - * Add option to disable MQTT as define USE_MQTT in user_config.h (#200) +- Fix web console command input when SUB_PREFIX contains '/' (#152) +- Add command response to web command (#200) +- Add option to disable MQTT as define USE_MQTT in user_config.h (#200) ### 3.1.12 20170106 - * Add OTA retry to solve possible HTTP transient errors (#204) - * Fix MQTT host discovery +- Add OTA retry to solve possible HTTP transient errors (#204) +- Fix MQTT host discovery ### 3.1.11 20170105 - * Add mDNS to advertise webserver as .local/ +- Add mDNS to advertise webserver as .local/ ### 3.1.10 20170105 - * Fix ButtonTopic when SUB_PREFIX = PUB_PREFIX - * Add workaround for possible MQTT queueing when SUB_PREFIX = PUB_PREFIX - * Add optional MQTT host discovery using define USE_DISCOVERY in user_config.h (#115) +- Fix ButtonTopic when SUB_PREFIX = PUB_PREFIX +- Add workaround for possible MQTT queueing when SUB_PREFIX = PUB_PREFIX +- Add optional MQTT host discovery using define USE_DISCOVERY in user_config.h (#115) ### 3.1.9 20170104 - * Fix Power Blink start position (toggled) - * Change PulseTime increments: 1 .. 111 in 0.1 sec (max 11 seconds) and 112 .. 64900 in seconds (= 12 seconds until 18 hours) (#188) - * Add support for SUB_PREFIX = PUB_PREFIX (#190) +- Fix Power Blink start position (toggled) +- Change PulseTime increments: 1 .. 111 in 0.1 sec (max 11 seconds) and 112 .. 64900 in seconds (= 12 seconds until 18 hours) (#188) +- Add support for SUB_PREFIX = PUB_PREFIX (#190) ### 3.1.8 20170103 - * Add retain flag to LWT offline and only send "tele/sonoff/LWT Offline" (#179) - * Change retained LWT Online message to only send "tele/sonoff/LWT Online" +- Add retain flag to LWT offline and only send "tele/sonoff/LWT Offline" (#179) +- Change retained LWT Online message to only send "tele/sonoff/LWT Online" ### 3.1.7 20161231 - * Add retained message LWT Online when sonoff makes MQTT connection (#179) +- Add retained message LWT Online when sonoff makes MQTT connection (#179) ### 3.1.6 20161230 - * Add blinking using commands BlinkTime, BlinkCount and Power Blink|3|BlinkOff|4 (#165) +- Add blinking using commands BlinkTime, BlinkCount and Power Blink|3|BlinkOff|4 (#165) ### 3.1.5 20161228 - * Fix serial space command exception (28) +- Fix serial space command exception (28) ### 3.1.4 20161227 - * Fix MQTT subscribe regression exception (3) (#162) - * Fix serial empty command exception (28) +- Fix MQTT subscribe regression exception (3) (#162) +- Fix serial empty command exception (28) ### 3.1.3 20161225 - * Extent Domoticz configuration webpage with optional indices (#153) - * Fix multi relay legacy tele message from tele/sonoff/2/POWER to tele/sonoff/POWER2 - * Add support for iTead Motor Clockwise/Anticlockwise +- Extent Domoticz configuration webpage with optional indices (#153) +- Fix multi relay legacy tele message from tele/sonoff/2/POWER to tele/sonoff/POWER2 +- Add support for iTead Motor Clockwise/Anticlockwise ### 3.1.2 20161224 - * Extent command PowerOnState with toggle at power on (option 2 is now option 3!) (#156) +- Extent command PowerOnState with toggle at power on (option 2 is now option 3!) (#156) ### 3.1.1 20161223 - * Add support for Sonoff Touch and Sonoff 4CH (#40) - * Update DomoticzIdx and DomoticzKeyIdx with relay/key index (DomoticzIdx1/DomoticzKeyIdx1) - * Add command PowerOnState to control relay(s) at power on (#154) +- Add support for Sonoff Touch and Sonoff 4CH (#40) +- Update DomoticzIdx and DomoticzKeyIdx with relay/key index (DomoticzIdx1/DomoticzKeyIdx1) +- Add command PowerOnState to control relay(s) at power on (#154) ### 3.1.0 20161221 - * Add Sonoff Pow measurement smoothing - * Fix serial command topic preamble error (#151) - * Fix 2.x to 3.x migration inconsistencies (#146) +- Add Sonoff Pow measurement smoothing +- Fix serial command topic preamble error (#151) +- Fix 2.x to 3.x migration inconsistencies (#146) ### 3.0.9 20161218 - * Add Sonoff Pow voltage reading when relay is on but no load present (#123) +- Add Sonoff Pow voltage reading when relay is on but no load present (#123) ### 3.0.8 20161218 - * Add temperature conversion to Fahrenheit as option in user_config.h (TEMP_CONVERSION) (#145) +- Add temperature conversion to Fahrenheit as option in user_config.h (TEMP_CONVERSION) (#145) ### 3.0.7 20161217 - * Add user_config_override.h to be used by user to override some defaults in user_config.h (#58) - * Fix Sonoff Pow low power (down to 4W) intermittent measurements (#123) +- Add user_config_override.h to be used by user to override some defaults in user_config.h (#58) +- Fix Sonoff Pow low power (down to 4W) intermittent measurements (#123) ### 3.0.6 20161217 - * Fix MQTT_CLIENT_ID starting with % sign as in "%06X" (#142) - * Add auto power off after PulseTime### 0.1 Sec to relay 1 (#134) +- Fix MQTT_CLIENT_ID starting with % sign as in "%06X" (#142) +- Add auto power off after PulseTime### 0.1 Sec to relay 1 (#134) ### 3.0.5 20161215 - * Add more control over LED with command LedState options (#136, #143) - * LED_OFF (0), LED_POWER (1), LED_MQTTSUB (2), LED_POWER_MQTTSUB (3), LED_MQTTPUB (4), LED_POWER_MQTTPUB (5), LED_MQTT (6), LED_POWER_MQTT (7) - * Add option WIFI_RETRY (4) to command WifiConfig to allow connection retry to other AP without restart (#73) +- Add more control over LED with command LedState options (#136, #143) +- LED_OFF (0), LED_POWER (1), LED_MQTTSUB (2), LED_POWER_MQTTSUB (3), LED_MQTTPUB (4), LED_POWER_MQTTPUB (5), LED_MQTT (6), LED_POWER_MQTT (7) +- Add option WIFI_RETRY (4) to command WifiConfig to allow connection retry to other AP without restart (#73) ### 3.0.4 20161211 - * Fix intermittent Domoticz update misses (#133) +- Fix intermittent Domoticz update misses (#133) ### 3.0.3 20161210 - * Fix compiler warnings (#132) - * Remove redundant code - * Fix Domoticz pushbutton support +- Fix compiler warnings (#132) +- Remove redundant code +- Fix Domoticz pushbutton support ### 3.0.2 20161209 - * Add pushbutton to SwitchMode (#130) +- Add pushbutton to SwitchMode (#130) ### 3.0.1 20161209 - * Fix initial config +- Fix initial config ### 3.0.0 20161208 - * Migrate and clean-up flash layout - * Settings from version 2.x are saved but settings from version 3.x can not be used with version 2.x - * Change SEND_TELEMETRY_RSSI to SEND_TELEMETRY_WIFI and add AP and SSID to telemetry - * Split long JSON messages - * Fix inconsistent status messages - * Fix all status messages to return JSON if enabled - * Remove relay index in cmnd/sonoff//POWER now changed - * to cmnd/sonoff/POWER for single relay units - * and cmnd/sonoff/POWER for multi relay units like Sonoff dual - * Add retain option to Power/Light status controlled by command PowerRetain On|Off (#126) +- Migrate and clean-up flash layout +- Settings from version 2.x are saved but settings from version 3.x can not be used with version 2.x +- Change SEND_TELEMETRY_RSSI to SEND_TELEMETRY_WIFI and add AP and SSID to telemetry +- Split long JSON messages +- Fix inconsistent status messages +- Fix all status messages to return JSON if enabled +- Remove relay index in cmnd/sonoff//POWER now changed +- to cmnd/sonoff/POWER for single relay units +- and cmnd/sonoff/POWER for multi relay units like Sonoff dual +- Add retain option to Power/Light status controlled by command PowerRetain On|Off (#126) ### 2.1.2 20161204 - * Add support for second wifi AP (#73) - * Update command WifiConfig - * Fix possible WifiManager hang +- Add support for second wifi AP (#73) +- Update command WifiConfig +- Fix possible WifiManager hang ### 2.1.1a 20161203 - * Fix scan for wifi networks if WeMo is enabled - * Fix syslog setting using web page +- Fix scan for wifi networks if WeMo is enabled +- Fix syslog setting using web page ### 2.1.1 20161202 - * Add support for ElectroDragon second relay and button (only toggle with optional ButtonTopic) (#110) +- Add support for ElectroDragon second relay and button (only toggle with optional ButtonTopic) (#110) ### 2.1.0 20161202 - * Add optional EXPERIMENTAL TLS to MQTT (#49) - * Fix MQTT payload handling (#111) - * Optimzed WeMo code +- Add optional EXPERIMENTAL TLS to MQTT (#49) +- Fix MQTT payload handling (#111) +- Optimzed WeMo code ### 2.0.21a 20161201 - * Fix WeMo PowerPlug emulation +- Fix WeMo PowerPlug emulation ### 2.0.21 20161130 - * Add Belkin WeMo PowerPlug emulation enabled with USE_WEMO_EMULATION in user_config.h (Heiko Krupp) (#105, #109) +- Add Belkin WeMo PowerPlug emulation enabled with USE_WEMO_EMULATION in user_config.h (Heiko Krupp) (#105, #109) ### 2.0.20 20161130 - * Relax MQTTClient naming but only allows hexadecimal uppercase numbers (#107) - * Add I2C support with command I2CScan - * Add I2C sensor driver for HTU21 as alternate sensor using TH10/16 connectors (Heiko Krupp) (#105) - * Add I2C sensor driver for BMP085/BMP180/BMP280/BME280 as alternate sensor using TH10/16 connectors +- Relax MQTTClient naming but only allows hexadecimal uppercase numbers (#107) +- Add I2C support with command I2CScan +- Add I2C sensor driver for HTU21 as alternate sensor using TH10/16 connectors (Heiko Krupp) (#105) +- Add I2C sensor driver for BMP085/BMP180/BMP280/BME280 as alternate sensor using TH10/16 connectors ### 2.0.19a 20161127 - * Add support for ButtonTopic and ButtonRetain to wall switch function - * Add pullup to SWITCH_PIN and command SwitchMode to syntax +- Add support for ButtonTopic and ButtonRetain to wall switch function +- Add pullup to SWITCH_PIN and command SwitchMode to syntax ### 2.0.18 20161126 - * Add SUB_PREFIX multi level support allowing 'cmnd' or 'cmnd/level2/level3' - * Add wall switch function to GPIO14 and command SwitchMode (Alex Scott) (#103) +- Add SUB_PREFIX multi level support allowing 'cmnd' or 'cmnd/level2/level3' +- Add wall switch function to GPIO14 and command SwitchMode (Alex Scott) (#103) ### 2.0.17 20161123 - * Calibrate HLWPCAL from 12345 to 12530 - * Add alternative sensor driver DHT2 using Adafruit DHT library - * Add define MESSAGE_FORMAT to user_config.h - * Throttle console messages - * Shorten JSON messages - * Fix possible Panic - * Fix User mode webserver security +- Calibrate HLWPCAL from 12345 to 12530 +- Add alternative sensor driver DHT2 using Adafruit DHT library +- Add define MESSAGE_FORMAT to user_config.h +- Throttle console messages +- Shorten JSON messages +- Fix possible Panic +- Fix User mode webserver security ### 2.0.16 20161118 - * Add alternative sensor driver DS18x20 using OneWire library (#95) - * Change sensor MQTT message from tele/sonoff/TEMPERATURE to tele/sonoff/DHT/TEMPERATURE or - * tele/sonoff/DS18B20/TEMPERATURE or tele/sonoff/DS18x20/1/TEMPERATURE - * Add sensors to root webpage and auto refresh every 4 seconds (#92) - * Add optional JSON messageformat to all telemetry data - * Enforce minimum TelePeriod to be 10 seconds - * Fix Energy Yesterday reset after restart - * Add Energy Today restore after controlled restart +- Add alternative sensor driver DS18x20 using OneWire library (#95) +- Change sensor MQTT message from tele/sonoff/TEMPERATURE to tele/sonoff/DHT/TEMPERATURE or +- tele/sonoff/DS18B20/TEMPERATURE or tele/sonoff/DS18x20/1/TEMPERATURE +- Add sensors to root webpage and auto refresh every 4 seconds (#92) +- Add optional JSON messageformat to all telemetry data +- Enforce minimum TelePeriod to be 10 seconds +- Fix Energy Yesterday reset after restart +- Add Energy Today restore after controlled restart ### 2.0.15 20161116 - * Change TODAY_POWER and PERIOD_POWER to TODAY_ENERGY and PERIOD_ENERGY - * Fix serial regression - * Fix syslog hangs when loghost is unavailable +- Change TODAY_POWER and PERIOD_POWER to TODAY_ENERGY and PERIOD_ENERGY +- Fix serial regression +- Fix syslog hangs when loghost is unavailable ### 2.0.14 20161115 - * Add HLW threshold delay - * Fix HLW intermittent current deviation - * Fix button functionality during wificonfig - * Add CRC check to DS18B20 sensor (#88) +- Add HLW threshold delay +- Fix HLW intermittent current deviation +- Fix button functionality during wificonfig +- Add CRC check to DS18B20 sensor (#88) ### 2.0.13 20161113 - * Add additional upload error code descriptions - * Add PlatformIO support (#80) +- Add additional upload error code descriptions +- Add PlatformIO support (#80) ### 2.0.12 20161113 - * Fix Serial and Web response regression when no MQTT connection available - * Fix Sonoff Dual power telemetric data for second relay - * Removed MQTT password from Information web page - * Hide MQTT password from Configure MQTT web page +- Fix Serial and Web response regression when no MQTT connection available +- Fix Sonoff Dual power telemetric data for second relay +- Removed MQTT password from Information web page +- Hide MQTT password from Configure MQTT web page ### 2.0.11 20161111 - * Rewrite button and web toggle code - * Fix NTP sync - * Add HLW calibration commands HLWPCAL, HLWUCAL and HLWICAL (need define USE_POWERCALIBRATION) - * Fix power threshold tests +- Rewrite button and web toggle code +- Fix NTP sync +- Add HLW calibration commands HLWPCAL, HLWUCAL and HLWICAL (need define USE_POWERCALIBRATION) +- Fix power threshold tests ### 2.0.10 20161109 - * Add additional Domoticz define (#63) - * Add defines MQTT_STATUS_ON and MQTT_STATUS_OFF in user_config.h to select status On/Off string - * Fix status response differences (#65) - * Fix divide by zero exception (#70) - * Fix syslog loop exception +- Add additional Domoticz define (#63) +- Add defines MQTT_STATUS_ON and MQTT_STATUS_OFF in user_config.h to select status On/Off string +- Fix status response differences (#65) +- Fix divide by zero exception (#70) +- Fix syslog loop exception ### 2.0.9 20161108 - * clarify MODULE in user_config.h - * Fix hlw false values +- clarify MODULE in user_config.h +- Fix hlw false values ### 2.0.8 20161108 - * Add initial status after power on - * Seperate driver files - * Fix hlw code and calibrate Pow - * Move user config defines to user_config.h (#61) +- Add initial status after power on +- Seperate driver files +- Fix hlw code and calibrate Pow +- Move user config defines to user_config.h (#61) ### 2.0.7 20161030 - * Make Ticker mandatory - * Add Domoticz support (Increase MQTT_MAX_PACKET_SIZE to 400) (#54) - * Add command MessageFormat 0|1 to select either legacy or JSON output +- Make Ticker mandatory +- Add Domoticz support (Increase MQTT_MAX_PACKET_SIZE to 400) (#54) +- Add command MessageFormat 0|1 to select either legacy or JSON output ### 2.0.6 20161024 - * Add Sonoff Pow power factor - * Initial support for up to four relays using iTEAD PSB (4Channel) - * - Currently only supports one button (All buttons behave the same) - * - Use command MODEL 4 to select four relay option - * (After first power on it will support 2 relays like Sonoff Dual) - * Fix ledstate - * Add command Status 9 to display Sonoff Pow thresholds - * Add commands PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow and CurrentHigh for use - * with Sonoff Pow thresholds +- Add Sonoff Pow power factor +- Initial support for up to four relays using iTEAD PSB (4Channel) +- - Currently only supports one button (All buttons behave the same) +- - Use command MODEL 4 to select four relay option +- (After first power on it will support 2 relays like Sonoff Dual) +- Fix ledstate +- Add command Status 9 to display Sonoff Pow thresholds +- Add commands PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow and CurrentHigh for use +- with Sonoff Pow thresholds ### 2.0.5 20161018 - * Add updates to user_config.h - moved SEND_TELEMETRY_DS18B20 and SEND_TELEMETRY_DHT to module area. - * As Sonoff TH10/16 does not have the logic installed for GPIO04 You'll have to select ONE of both - * Add Sonoff Pow support (experimental until Pow tested) - * Add command Status 8 to display Sonoff Pow energy values - * Add command MqttUnits On|Off to add units to values - * Change web main page header character size - * Change On/Off to ON/OFF status messages to satisfy openHAB - * Change TEMP to TEMPERATURE and HUM to HUMIDITY +- Add updates to user_config.h - moved SEND_TELEMETRY_DS18B20 and SEND_TELEMETRY_DHT to module area. +- As Sonoff TH10/16 does not have the logic installed for GPIO04 You'll have to select ONE of both +- Add Sonoff Pow support (experimental until Pow tested) +- Add command Status 8 to display Sonoff Pow energy values +- Add command MqttUnits On|Off to add units to values +- Change web main page header character size +- Change On/Off to ON/OFF status messages to satisfy openHAB +- Change TEMP to TEMPERATURE and HUM to HUMIDITY ### 2.0.4 20161009 - * Add MQTT_BUTTON_RETAIN, SAVE_DATA and SAVE_STATE defines to user_config.h (#35) - * Update ButtonRetain to remove retained message(s) from broker when turned off - * Add Retain for second relay on Sonoff Dual - * Provide power status messages with device topic index if requested +- Add MQTT_BUTTON_RETAIN, SAVE_DATA and SAVE_STATE defines to user_config.h (#35) +- Update ButtonRetain to remove retained message(s) from broker when turned off +- Add Retain for second relay on Sonoff Dual +- Provide power status messages with device topic index if requested ### 2.0.3 20161008 - * Update wifi initialization - * Add command BUTTONRETAIN for optional MQTT retain on button press (#35) - * Add command SAVESTATE to disable power state save. May be used with MQTT retain +- Update wifi initialization +- Add command BUTTONRETAIN for optional MQTT retain on button press (#35) +- Add command SAVESTATE to disable power state save. May be used with MQTT retain ### 2.0.2 20161006 - * Fix wifi issue 2186 +- Fix wifi issue 2186 ### 2.0.1 20161002 - * Fix button press +- Fix button press ### 2.0.0 20161002 - * Update Sonoff TH10/16 sensor pins (My TH10 only has GPIO14 connected) - * Add full support for Sonoff dual +- Update Sonoff TH10/16 sensor pins (My TH10 only has GPIO14 connected) +- Add full support for Sonoff dual ### 1.0.35 20160929 - * Add more lines to console - * Add timeout and disable MQTT on web upload - * Add command SAVEDATA to control parameter save (for flash wear afficionados) (#30) +- Add more lines to console +- Add timeout and disable MQTT on web upload +- Add command SAVEDATA to control parameter save (for flash wear afficionados) (#30) ### 1.0.34 20160926 - * Fix button press six and seven - * Add more information to webserver +- Fix button press six and seven +- Add more information to webserver ### 1.0.33 20160915 - * Better WPS error message - * Separate webserver code from support.ino into webserver.ino - * Fix webserver User by removing unwanted restart option +- Better WPS error message +- Separate webserver code from support.ino into webserver.ino +- Fix webserver User by removing unwanted restart option ### 1.0.32 20160913 - * Add Wifi Protected Setup (WPS) as third option for initial config - * Add command WIFICONFIG replacing deprecated command SMARTCONFIG - * Add option WIFICONFIG 3 to start WPSconfig - * Add option WIFICONFIG 0 to start saved Wifi config tool (WPSconfig, Smartconfig or Wifimanager) - * Change button behaviour - See Wiki +- Add Wifi Protected Setup (WPS) as third option for initial config +- Add command WIFICONFIG replacing deprecated command SMARTCONFIG +- Add option WIFICONFIG 3 to start WPSconfig +- Add option WIFICONFIG 0 to start saved Wifi config tool (WPSconfig, Smartconfig or Wifimanager) +- Change button behaviour - See Wiki ### 1.0.31 20160907 - * Fix DS18B20 misread if teleperiod = 2 - * Tuned sensor code - * Updated prefered ElectroDragon connection to Relay 1 and Button 1 - * Moved SONOFF and ELECTRO_DRAGON port config to user_config.h +- Fix DS18B20 misread if teleperiod = 2 +- Tuned sensor code +- Updated prefered ElectroDragon connection to Relay 1 and Button 1 +- Moved SONOFF and ELECTRO_DRAGON port config to user_config.h ### 1.0.30 20160902 - * Fix command TELEPERIOD 0 - * Add ESP- tag to UDP log message for easy rsyslogd filtering - * Add ElectroDragon (Relay 2 only) functionality. Select with #define MODULE ELECTRO_DRAGON - * Add ? as null message alternative - * Add DHT temperature and humidity telemetry support. Enable with #define SEND_TELEMETRY_DHT - * Add DS18B20 temperature telemetry support. Enable with #define SEND_TELEMETRY_DS18B20 - * Restrict HOSTNAME, MQTTCLIENT, TOPIC and BUTTONTOPIC in topic mode only +- Fix command TELEPERIOD 0 +- Add ESP- tag to UDP log message for easy rsyslogd filtering +- Add ElectroDragon (Relay 2 only) functionality. Select with #define MODULE ELECTRO_DRAGON +- Add ? as null message alternative +- Add DHT temperature and humidity telemetry support. Enable with #define SEND_TELEMETRY_DHT +- Add DS18B20 temperature telemetry support. Enable with #define SEND_TELEMETRY_DS18B20 +- Restrict HOSTNAME, MQTTCLIENT, TOPIC and BUTTONTOPIC in topic mode only ### 1.0.29 20160831 - * Allow UPGRADE, OTAURL, RESTART, RESET, MQTTHOST, MQTTPORT, MQTTUSER, MQTTPASSWORD and WEBSERVER also in group mode +- Allow UPGRADE, OTAURL, RESTART, RESET, MQTTHOST, MQTTPORT, MQTTUSER, MQTTPASSWORD and WEBSERVER also in group mode ### 1.0.28 20160831 - * Add webserver state to status 5 - * Add optional PUB_PREFIX2 (tele) for telemetry usage - * Add command TELEPERIOD - * Fix syntax message - * Change memory status display +- Add webserver state to status 5 +- Add optional PUB_PREFIX2 (tele) for telemetry usage +- Add command TELEPERIOD +- Fix syntax message +- Change memory status display ### 1.0.27 20160831 - * Add sketch flash size - * Add console to webserver - * Add command weblog - * Change WifiManager web pages to minimal - * Change display default hostname and MQTT client id in webserver - * Change HTTP command interface to http://sonoff-1234/cm?cmnd=light 2 - * Change HEARTBEAT to UPTIME +- Add sketch flash size +- Add console to webserver +- Add command weblog +- Change WifiManager web pages to minimal +- Change display default hostname and MQTT client id in webserver +- Change HTTP command interface to http://sonoff-1234/cm?cmnd=light 2 +- Change HEARTBEAT to UPTIME ### 1.0.26 20160829 - * Add define USE_WEBSERVER to disable web server code in source - * Add file upload as alternative for ota upload to webserver - * Add information to webserver - * Add command hostname - * Add command logport - * Change HTTP command interface to http://sonoff-1234/cmd?cmnd=light 2 - * Change button behaviour with regards to Smartconfig and OTA upload. See README.md - * Enforce default hostname to either "%s-%04d" or user defined without any % - * Enforce default mqtt client id to either "DVES_%06X" or user defined without any % +- Add define USE_WEBSERVER to disable web server code in source +- Add file upload as alternative for ota upload to webserver +- Add information to webserver +- Add command hostname +- Add command logport +- Change HTTP command interface to http://sonoff-1234/cmd?cmnd=light 2 +- Change button behaviour with regards to Smartconfig and OTA upload. See README.md +- Enforce default hostname to either "%s-%04d" or user defined without any % +- Enforce default mqtt client id to either "DVES_%06X" or user defined without any % ### 1.0.25 20160822 - * Remove config system halts to keep ota available +- Remove config system halts to keep ota available ### 1.0.24 20160821 - * Add test for MQTT_SUBTOPIC - * Change log range to LOG_LEVEL_ALL - * Change MQTT introduction messages - * Moved MQTT_MAX_PACKET_SIZE warning message to introduction messages +- Add test for MQTT_SUBTOPIC +- Change log range to LOG_LEVEL_ALL +- Change MQTT introduction messages +- Moved MQTT_MAX_PACKET_SIZE warning message to introduction messages ### 1.0.23 20160821 - * Add option USE_SPIFFS to move config from flash to spiffs - * Add webserver with options 0 (off), 1 (user) and 2 (admin) - * Add HTTP command interface (http://sonoff-1234/c?cmnd=light 2) - * Add wifimanager countdown counter - * Add command line webpage - * Add relay control to wifimanager - * Add restart option 99 to force restart - * Fix wifi hostname - * Fix NETBIOS hostname problem by reducing default hostname length - * Fix possible exception if WIFI_HOSTNAME is changed - * Fix upgrade messages - * Reduce memory use by redesigning config routines - * Split syntax message - * Rename define SERIAL_IO to USE_SERIAL +- Add option USE_SPIFFS to move config from flash to spiffs +- Add webserver with options 0 (off), 1 (user) and 2 (admin) +- Add HTTP command interface (http://sonoff-1234/c?cmnd=light 2) +- Add wifimanager countdown counter +- Add command line webpage +- Add relay control to wifimanager +- Add restart option 99 to force restart +- Fix wifi hostname +- Fix NETBIOS hostname problem by reducing default hostname length +- Fix possible exception if WIFI_HOSTNAME is changed +- Fix upgrade messages +- Reduce memory use by redesigning config routines +- Split syntax message +- Rename define SERIAL_IO to USE_SERIAL ### 1.0.22 20160814 - * Add all MQTT parameters for configuration - * Add wifimanager to configure Wifi and MQTT via web server - * Change NTP time handling - * Fix Smartconfig parameter buffer overflow - * Fix PlatformIO warnings +- Add all MQTT parameters for configuration +- Add wifimanager to configure Wifi and MQTT via web server +- Change NTP time handling +- Fix Smartconfig parameter buffer overflow +- Fix PlatformIO warnings ### 1.0.21 20160808 - * Remove semaphore as subscription flooding (more than 15 subscriptions per second) is managed by SDK (LmacRxBlk:1) - * Add optional RTC interrupt (define USE_TICKER) to keep RTC synced during subscription flooding - * Remove heartbeatflag +- Remove semaphore as subscription flooding (more than 15 subscriptions per second) is managed by SDK (LmacRxBlk:1) +- Add optional RTC interrupt (define USE_TICKER) to keep RTC synced during subscription flooding +- Remove heartbeatflag ### 1.0.20 20160805 - * Add semaphore to handle out of memory when too many subscriptions requested - * Use Daylight Saving (DST) parameters from user_config.h when timezone = 99 - * Add status 7 option displaying RTC information - * Add ledstate to status 0 +- Add semaphore to handle out of memory when too many subscriptions requested +- Use Daylight Saving (DST) parameters from user_config.h when timezone = 99 +- Add status 7 option displaying RTC information +- Add ledstate to status 0 ### 1.0.19 20160803 - * Fix possible MQTT_CLIENT_ID induced Exception(28) +- Fix possible MQTT_CLIENT_ID induced Exception(28) ### 1.0.18 20160803 - * Moved Cfg_Default - * Fix negative data handling - * Remove MQTT information from status 1 and add labels to status 1 - * Add mac address to status 5 - * Add MQTT ClientId, UserId and Password to status 6 +- Moved Cfg_Default +- Fix negative data handling +- Remove MQTT information from status 1 and add labels to status 1 +- Add mac address to status 5 +- Add MQTT ClientId, UserId and Password to status 6 ### 1.0.17 20160731 - * Better variable range checking - * Change ambiguous connection messages - * Add timestamp to serial message +- Better variable range checking +- Change ambiguous connection messages +- Add timestamp to serial message ### 1.0.16 20160729 - * Moved wifi, rtc, syslog and config to support.ino - * Fixed button action when buttontopic is used. Introduced with 1.0.15 - * Better buffer overflow checks (strlcpy) +- Moved wifi, rtc, syslog and config to support.ino +- Fixed button action when buttontopic is used. Introduced with 1.0.15 +- Better buffer overflow checks (strlcpy) ### 1.0.15 20160728 - * Removed pubsubclient config changes from sonoff.ino as it doesn't work - * reapply MQTT_MAX_PACKET_SIZE 256 and MQTT_KEEPALIVE 120 to PubSubClient.h - * Add status 0 option displaying all status messages - * Change MQTT_MAX_PACKET_SIZE from 1024 to 256 - * Add buffer overflow checks (snprintf and strncpy) - * Implemented common string sizes +- Removed pubsubclient config changes from sonoff.ino as it doesn't work +- reapply MQTT_MAX_PACKET_SIZE 256 and MQTT_KEEPALIVE 120 to PubSubClient.h +- Add status 0 option displaying all status messages +- Change MQTT_MAX_PACKET_SIZE from 1024 to 256 +- Add buffer overflow checks (snprintf and strncpy) +- Implemented common string sizes ### 1.0.14 20160722 - * Seperate user config from sonoff.ino to user_config.h (pucebaboon) - * Change defaults from sidnas2 to domus1 - * Add MQTT status message as status 6 (pucebaboon) - * Add status type to message (pucebaboon) - * Add pubsubclient config changes to sonoff.ino (pucebaboon) +- Seperate user config from sonoff.ino to user_config.h (pucebaboon) +- Change defaults from sidnas2 to domus1 +- Add MQTT status message as status 6 (pucebaboon) +- Add status type to message (pucebaboon) +- Add pubsubclient config changes to sonoff.ino (pucebaboon) ### 1.0.13 20160702 - * Add Ledstate 1 option to show power state on led +- Add Ledstate 1 option to show power state on led ### 1.0.12 20160529 - * Allow disable of button topic using "0" +- Allow disable of button topic using "0" ### 1.0.11 20160524 - * Provide button response if MQTT connection lost +- Provide button response if MQTT connection lost ### 1.0.10 20160520 - * Add optional button topic to assist external MQTT clients - * Change version notation - * Reset default values +- Add optional button topic to assist external MQTT clients +- Change version notation +- Reset default values ### 1.0.9 20160503 - * Add more blinks - * Add reset 2 option erasing flash - * Add status 5 option displaying network info - * Add syslog check for Wifi connection - * Resize MqttPublish log array - * Change Wifi smartconfig active from 100 to 60 seconds - * Update Wifi initialization +- Add more blinks +- Add reset 2 option erasing flash +- Add status 5 option displaying network info +- Add syslog check for Wifi connection +- Resize MqttPublish log array +- Change Wifi smartconfig active from 100 to 60 seconds +- Update Wifi initialization ### 1.0.8 20160430 - * Remove use of Wifi config data from SDK - * Add status 3 (syslog info) and status 4 (flash info) - * Add restart option to button (5 quick presses) +- Remove use of Wifi config data from SDK +- Add status 3 (syslog info) and status 4 (flash info) +- Add restart option to button (5 quick presses) ### 1.0.7 20160420 - * Add UDP syslog support - * Change HOST command to MQTTHOST command - * Add commands SYSLOG, SERIALLOG and LOGHOST - * Change hostname to lower case to distinguise between open-sdk version - * Add support for ESP-12F used in my modified wkaku power socket switch - * Fix timezone command - * Add RTC month names for future use - * Modify button code - * Remove initialization errors by better use of MQTT loop +- Add UDP syslog support +- Change HOST command to MQTTHOST command +- Add commands SYSLOG, SERIALLOG and LOGHOST +- Change hostname to lower case to distinguise between open-sdk version +- Add support for ESP-12F used in my modified wkaku power socket switch +- Fix timezone command +- Add RTC month names for future use +- Modify button code +- Remove initialization errors by better use of MQTT loop ### 1.0.6 20160406 - * Removed Wifi AP mode (#1) - * Add test for Arduino IDE version >= 1.6.8 - * Fix RTC time sync code +- Removed Wifi AP mode (#1) +- Add test for Arduino IDE version >= 1.6.8 +- Fix RTC time sync code ### 1.0.5 20160310 - * Initial public release - * Show debug info by selecting option from IDE Tools Debug port: Serial +- Initial public release +- Show debug info by selecting option from IDE Tools Debug port: Serial diff --git a/tasmota/_changelog.ino b/tasmota/_changelog.ino deleted file mode 100644 index d36ae512d..000000000 --- a/tasmota/_changelog.ino +++ /dev/null @@ -1,1987 +0,0 @@ -/*********************************************************************************************\ - * 7.0.0.6 20191122 - * Add colorpicker to WebUI by Christian Staars (#6984) - * - * 7.0.0.5 20191118 - * Fix boot loop regression - * Add command TempOffset -12.6 .. 12.6 to set global temperature sensor offset (#6958) - * Fix check deepsleep for valid values in Settings (#6961) - * Fix Wifi instability when light is on, due to sleep=0 (#6961, #6608) - * Add hardware detection to be overruled with SetOption51 (#6969) - * - * 7.0.0.4 20191108 - * Add command WifiPower 0 .. 20.5 to set Wifi Output Power which will be default set to 17dBm - * Change supported PCF8574 I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time - * Change supported PCF8574A I2C address range to 0x39 - 0x3F allowing other I2C devices with address 0x38 to be used at the same time - * Change supported MCP230xx I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time - * Add Keep last channels values when Color command end with '=' (#6799) - * Add support for I2C sensor TLS2591 Light Intensity sensor (#6873) - * Change Kept only NEC/RC5/RC6/HASH IR protocols in standard Tasmota, all other protocols require Tasmota-IR, saving 4K - * Add command SetOption76 0/1 to enable incrementing bootcount when deepsleep is enabled (#6930) - * Change Reset erase end address from as seen by SDK (getFlashChipSize) to full flash size (getFlashChipRealSize) - * Change Zigbee log verbosity reduction - * - * 7.0.0.3 20191103 - * Add command I2cDriver for I2C driver runtime control using document I2CDEVICES.md - * Fix random crash caused by UPNP flood - * Add support for Honeywell HPMA115S0 particle concentration sensor by David Hunt (#6843) - * Remove driver xsns_12_ads1115_i2cdev replaced by xsns_12_ads1115 - * - * 7.0.0.2 20191102 - * Add command WebColor19 to control color of Module and Name (#6811) - * Add support for Honeywell I2C HIH series Humidity and Temperetaure sensor (#6808) - * Fix wrong Dimmer behavior introduced with #6799 when SetOption37 < 128 - * Change add DS18x20 support in Tasmota-IR - * Add Zigbee command support, considered as v1.0 for full Zigbee support - * Fix Reduce flash size after change to IRremoteESP8266 v2.7.0 - * - * 7.0.0.1 20191027 - * Remove update support for versions before 6.0 - * Change default GUI to dark theme - * Add command SetOption73 0/1 to re-enable HTTP Cross-Origin Resource Sharing (CORS) now default disabled (#6767) - * Add frequency to ADE7953 energy monitor as used in Shelly 2.5 by ljakob (#6778) - * Add command SetOption74 0/1 to enable DS18x20 internal pull-up and remove define DS18B20_INTERNAL_PULLUP (#6795) - * Fix better control of RGB/White when SetOption37 >128, added Dimmer1 and Dimmer2 commands (#6714) - * Add hide Alexa objects with friendlyname starting with '$' (#6722, #6762) - * Add command SetOption75 0/1 to switch between grouptopic (0) using fulltopic replacing %topic% or (1) is cmnd/ (#6779) - * Change Update IRremoteESP8266 to v2.7.0 - * - * 6.7.1.1 20191026 - * Change ArduinoSlave to TasmotaSlave (Experimental) - * Add support for Tuya battery powered devices (#6735) - * Change repository name from Sonoff-Tasmota to Tasmota - * Change all code references from Sonoff to Tasmota - * - * 6.7.1 20191026 - * Release - * Fix on energy monitoring devices using PowerDelta Exception0 with epc1:0x4000dce5 = Divide by zero (#6750) - * Fix Script array bug (#6751) - * - * 6.7.0 20191025 - * Release - * - * 6.6.0.21 20191022 - * Remove support for WPS and SmartConfig in favour of Web server (!) based WifiManager (#6680) - * Remove binary sonoff-classic (#6680) - * Remove command SetOption2 - * - * 6.6.0.20 20191018 - * Add command SetOption65 0/1 to disable (1) fast power cycle detection fixing unwanted brownout trigger - * Add absolute PowerDelta using command PowerDelta 101..32000 where 101 = 101-100 = 1W, 202 = 202-100 = 102W (#5901) - * Add support for EX-Store WiFi Dimmer V4 (#5856) - * Add ZigbeeRead command and many improvements (#6095) - * Add ArduinoSlave driver (EXPERIMENTAL) - * - * 6.6.0.19 20191018 - * Replace obsolete xsns_23_sdm120 with xnrg_08_sdm120 and consolidate define USE_SDM120 - * Replace obsolete xsns_25_sdm630 with xnrg_10_sdm630 and consolidate define USE_SDM630 - * Replace obsolete xsns_49_solaxX1 with xnrg_12_solaxX1 (#6677) - * - * 6.6.0.18 20191010 - * Add command DimmerRange in Light module to support 2 byte dimming ranges from Tuya - * Add Zigbee additional commands and sending messages to control devices (#6095) - * Fix Rules were not triggered with IR unknown protocol or in sonoff-it (#6629) - * Add define USE_DEEPSLEEP and command DeepSleepTime 0 or 10..86400 (seconds) to enter deepsleep mode (#6638) - * Add define USE_SONOFF_RF to enable/disable Sonoff Rf support (#6648) - * Add incremental beeps to Ifan03 remote control fan speed buttons (#6636) - * Add rule support after every command execution like Fanspeed#Data=2 (#6636) - * Fix handling of ligth channels when pwm_multichannel (Option68) is enabled - * Add WebUI for multiple, independent PWM channels - * Remove default DS18B20 driver and only support define DS18x20 (#6647) - * Add support for PMS3003 dust particle sensor - * Change Sonoff L1 support by adding define USE_SONOFF_L1 - * - * 6.6.0.17 20191009 - * Add command SetOption34 0..255 to set backlog delay. Default value is 200 (mSeconds) (#6562) - * Add command Gpio 255 to show physical GPIO configuration of all non-flash pins (#6407) - * - * 6.6.0.16 20191008 - * Change PZEM004T default address mask from 0.0.0.x to 192.168.1.x for legacy reason (#6585) - * Fix PZEM004T, PZEMAC and PZEMDC autodetection (#6585) - * Change light drivers internals to ease management - * - * 6.6.0.15 20191003 - * Change command PulseTime JSON message format and allow display of all pulsetimer information (#6519) - * Add support for Chint DDSU666 Modbus energy meter by Pablo Zerón - * Add support for SM2135 as used in Action LSC Smart Led E14 (#6495) - * Add command SetOption72 0/1 to switch between software (0) or hardware (1) energy total counter (#6561) - * Add Zigbee tracking of connected devices and auto-probing of Manuf/Model Ids - * Fix better handling of PWM White Temperature mode for Module 48 (#6534) - * - * 6.6.0.14 20190925 - * Change command Tariffx to allow time entries like 23 (hours), 1320 (minutes) or 23:00. NOTE: As this is development branch previous tariffs are lost! (#6488) - * Remove support for define USE_DS18x20_LEGACY and legacy DS18x20 driver (#6486) - * Add initial support for MQTT logging using command MqttLog (#6498) - * Add Zigbee more support - collect endpoints and clusters, added ZigbeeDump command - * Add initial support for shutters by Stefan Bode (#288) - * Add command to MCP230xx: sensor29 pin,0/1/2 for OFF/ON/TOGGLE - * Add initial support for PCF8574 I2C I/O Expander (currently output only) by Stefan Bode - * Add command SetOption71 0/1 to switch between different Modbus Active Energy registers on DDS238-2 energy meters (#6531) - * Change command SetOption43 to make it more general. Now supports PS_16_DZ driver too (#6544) - * Change command handling by moving buffers up in chain solving MQTTlog support (#6529) - * Change detection of non-MQTT commands by allowing non-space characters as delimiter (#6540) - * Fix TasmotaSerial: move serial send to IRAM for high speed baud rates - * - * 6.6.0.13 20190922 - * Add command EnergyReset4 x,x to initialize total usage for two tarrifs - * Add command EnergyReset5 x,x to initialize total export (or production) for two tarrifs - * Add command Sensor34 8,0 and Sensor34 8,1 to disable/enable JSON message on weight change over 4 gram - * Add JSON array index support to rules evaluation allowing trigger on ENERGY#POWER[2]>0.60 from JSON ..,"Power":[0.00,0.68],.. (#6160) - * - * 6.6.0.12 20190910 - * Redesign command Tariff to now default to 0 (=disabled) and allowing to set both Standard Time (ST) and Daylight Savings Time (DST) start hour - * Commands Tariff1 22,23 = Tariff1 (Off-Peak) ST,DST Tariff2 (Standard) 6,7 = Tariff2 ST,DST Tariff9 0/1 = Weekend toggle (1 = Off-Peak during weekend) - * Change rename "Data" to "Hash" and limit to 32 bits when receiving UNKNOWN IR protocol (see DECODE_HASH from IRremoteESP8266) - * Add command Gpios 255/All to show all available GPIO components (#6407) - * Change JSON output format for commands Adc, Adcs, Modules, Gpio and Gpios from list to dictionary (#6407) - * Add Zigbee support phase 3 - support for Xiaomi lumi.weather air quality sensor, Osram mini-switch - * Change energy sensors for three phase/channel support - * Add support for Shelly 2.5 dual energy (#6160) - * Add initial support for up to three PZEM-014/-016 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315) - * Add initial support for up to three PZEM-004T on serial connection with addresses x.x.x.1 (default), 2 and 3 (#2315) - * Add initial support for up to three PZEM-003/-017 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315) - * Add driver USE_SDM630_2 as future replacement for USE_SDM630 - Pls test and report - * Add command ModuleAddress 1/2/3 to set Pzem module address when a single module is connected (#2315) - * - * 6.6.0.11 20190907 - * Change Settings crc calculation allowing short term backward compatibility - * Add support for up to 4 INA226 Voltage and Current sensors by Steve Rogers (#6342) - * Change Improve reliability of TasmotaSerial at 115200 bauds and reduce IRAM usage for Stage/pre-2.6 - * Add support for A4988 stepper-motor-driver-circuit by Tim Leuschner (#6370) - * Add support for Hiking DDS238-2 Modbus energy meter by Matteo Campanella (#6384) - * - * 6.6.0.10 20190905 - * Redesign Tuya support by Shantur Rathore removing commands SetOption34, 41, 44, 45, 46 and 65 (#6353) - * Add command Reset 99 to reset bootcount to zero (#684, #6351) - * Change command Time 1/2/3 to select JSON time format ISO, ISO + Epoch or Epoch for legacy reason - * - * 6.6.0.9 20190828 - * Change theoretical baudrate range to 300..19660500 bps in 300 increments (#6294) - * Add Full support of all protocols in IRremoteESP8266, to be used on dedicated-IR Tasmota version. Warning: +81k Flash when compiling with USE_IR_REMOTE_FULL - * Add compile time define USE_WS2812_HARDWARE to select hardware type WS2812, WS2812X, WS2813, SK6812, LC8812 or APA106 (DMA mode only) - * Add 'sonoff-ir' pre-packaged IR-dedicated firmware and 'sonoff-ircustom' to customize firmware with IR Full protocol support - * Add Zigbee support phase 2 - cc2530 initialization and basic ZCL decoding - * Add driver USE_SDM120_2 with Domoticz P1 Smart Meter functionality as future replacement for USE_SDM120 - Pls test and report - * Add command Power0 0/1/2/Off/On/Toggle to control all power outputs at once (#6340) - * Add time to more events (#6337) - * Add command Time 1/2/3 to select JSON time format ISO + Epoch, ISO or Epoch - * - * 6.6.0.8 20190827 - * Add Tuya Energy monitoring by Shantur Rathore - * Add phase 1 Domoticz P1 Smart Meter support using energy sensors handled by xdrv_03_energy.ino based on an idea by pablozg - * Add commands Tariff1 0..23 (start Off-Peak hour), Tariff2 0..23 (start Standard hour) and Tariff3 0/1 (Saturday and Sunday Off-Peak) - * - * 6.6.0.7 20190825 - * Expand Settings area to 4k for future use - * - * 6.6.0.6 20190819 - * Add I2C display driver for SH1106 oled by Gerhard Mutz - * Add SPI display drivers for epaper 4.2 inch, ILI9488 TFT, SSD1351 Color oled and RA8876 TFT by Gerhard Mutz - * Add support for HM17 bluetooth LE passive scan of ibeacon devices by Gerhard Mutz - * - * 6.6.0.5 20190816 - * Add command WebSensor 0/1 to control display of sensor data in web GUI (#6085) - * Change some table locations from RAM to Flash - * Fix wrong telemetry message when SetOption68 1 (#6191) - * Add support for RDM6300 125kHz RFID Reader by Gerhard Mutz - * - * 6.6.0.4 20190806 - * Add support for CHIRP soil moisture sensor by Christian Baars - * Add debug compile features using defines DEBUG_TASMOTA_CORE, DEBUG_TASMOTA_DRIVER and DEBUG_TASMOTA_SENSOR. - * See DEBUG_CORE_LOG example in sonoff.ino and DEBUG_DRIVER_LOG example in xdrv_09_timers.ino - * Add support for Solax X1 inverter by Pablo Zerón - * Add ZigBee support phase 1 - low level MQTT ZNP messages for CC2530 devices - * Add command Buzzer with optional parameters ,, enabled when a buzzer is configured (#5988) - * Add support for PAJ7620 gesture sensor by Christian Baars - * - * 6.6.0.3 20190725 - * Change filename of configuration backup from using FriendlyName1 to Hostname solving diacritic issues (#2422) - * Change Store AWS IoT Private Key and Certificate in SPI Flash avoiding device-specific compilations - * Upgrade library IRRemoteEsp8266 to 2.6.4, now using sendPioneer() - * Add support for MAX31865 Thermocouple sensor by Alberto Lopez Siemens - * Add option 0 to Width1 (Marker), Width2 (Second), Width3 (Minute) and Width4 (Hour) disabling display (#6152) - * Add MqttCount metric to STATE (#6155) - * Add define USE_ENERGY_MARGIN_DETECTION to disable Energy Margin and Power Limit detection - * Add define USE_ENERGY_POWER_LIMIT to disable Energy Power Limit detection while Energy Margin detection is active - * Add allow repeat/longpress for IRSend raw, introduced IRSend option (#6074) - * Add SetOption68 to enable multi-channel PWM instead of a single light (#6134) - * - * 6.6.0.2 20190714 - * Change commands Var and Mem to show all parameters when no index is given (#6107) - * Add command SetOption67 0/1 to disable or enable a buzzer as used in iFan03 - * Add command DisplayWidth to set pixel width on supported devices - * Add command DisplayHeight to set pixel height on supported devices - * Add support for Sonoff iFan03 as module 71 (#5988) - * Add support for a buzzer - * Add support for IRSend long press ('repeat' feature from IRRemoteESP8266) (#6074) - * Add support for IRHVAC Midea/Komeco protocol (#3227) - * Add support for more IRSend protocols enabled in my_user_config.h - * Add support for IRSend Pioneer protocol (#6100) - * Add Oled reset GPIO option "OLED reset" - * - * 6.6.0.1 20190708 - * Fix Domoticz battery level set to 100 if define USE_ADC_VCC is not used (#6033) - * Fix Force Elliptic Curve for Letsencrypt TLS #6042 - * Fix WeMo emulation for 1G echo and 2G echo dot (#6086) - * Fix Xiaomi Philips brightness (#6091) - * Change defines USE_TX20_WIND_SENSOR and USE_RC_SWITCH in my_user_config.h to disable to lower iram usage enabling latest core compilation (#6060, #6062) - * Add blend RGB leds with White leds for better whites (#5895, #5704) - * Add command SetOption41 0..8 to control number of Tuya switches (#6039) - * Add command SetOption42 0..255 to set overtemperature (Celsius only) threshold resulting in power off all on energy monitoring devices. Default setting is 90 (#6036) - * Add command SetOption66 0/1 to enable or disable Tuya dimmer range 255 slider control - * Add command Time to disable NTP and set UTC time as Epoch value if above 1451602800 (=20160101). Time 0 re-enables NTP (#5279) - * Add AZ7798 automatic setting of clock display (#6034) - * Add Epoch and UptimeSec to JSON messages (#6068) - * Add support for up to 4 INA219 sensors (#6046) - * - * 6.6.0 20190707 - * Remove support of TLS on core 2.3.0 and extent support on core 2.4.2 and up - * Remove MQTT uptime message every hour - * Refactor some defines to const - * Refactor webserver HTML input, button, textarea, and select name based on id - * Refactor webserver sensor data collection - * Refactor TLS based on BearSSL, warning breaking change for fingerprints validation - * Refactor management of lights, using classes and integers instead of floats - * Refactor UDP initial message handling from string to char using static memory and add debug info (#5505) - * Refactor IRSend and receive for 64-bit support (#5523) - * Refactor MQTT which might solve issue (#5755) - * Refactor IRSend by using heap when more than 199 values need to be send. May need increase of define MQTT_MAX_PACKET_SIZE too (#5950) - * Refactor double to float in rules, and replaced trigonometric functions from stdlib with smaller versions (#6005) - * Change pubsubclient MQTT_KEEPALIVE from 10 to 30 seconds for AWS IoT support - * Change gamma correction as default behavior, ie "Ledtable 1" - * Change PWM resolution from 8 to 10 bits for low brightness lights - * Change IRSend Panasonic protocol to 64-bit (#5523) - * Change ADC0 to enabled by default in my_user_config.h (#5671) - * Change define USE_EMULATION by USE_EMULATION_HUE and USE_EMULATION_WEMO (#5826) - * Change default PowerDelta from 80% to 0% on new installations (#5858, #5028, #4813, #4130, #4145, #3795, #3778, #3660, #3648) - * Fix display Bug in KNX webmenu for Physical Address - * Fix the Unescape() function and the SendSerial3 behaviour - * Fix webserver multiple Javascript window.onload functionality - * Fix TasmotaSerial at 9600 bps solving DFPlayer comms (#5528) - * Fix Configure Timer Web GUI (#5568) - * Fix Shelly 2.5 I2C address priority issue when VEML6070 code is present by disabling VEML6070 for Shelly 2.5 (#5592) - * Fix use of SerialDelimiter value 128 (#5634) - * Fix Sonoff Pow R2 / S31 invalid energy increments (#5789) - * Fix core 2.5.x ISR not in IRAM exception (#5837) - * Fix Philips Hue emulation Alexa issue by using part of MAC address for LightId (#5849) - * Fix missing white channel for WS2812 (#5869) - * Fix PZem startup issue (#5875) - * Fix exception 9 when syslog is enabled and NTP is just synced (#5917) - * Fix Toggle functionality to button double press when one button and two devices are detected (#5935) - * Fix channel command for dual dimmers (#5940) - * Fix not restoring white value on power off/power on (#5993) - * Add command AdcParam to control ADC0 Temperature and Light formula parameters - * Add command LedMask to assign which relay has access to power LED (#5602, #5612) - * Add extended LED power control using command LedPowerX where X is 1 to 4. Enabled when "LedLink(i)" is configured too (#5709) - * Add command Sensor20 1..255 to change Nova Fitness SDS01 working period in minutes (#5452) - * Add command SetOption38 6..255 to set IRReceive protocol detection sensitivity mimizing UNKNOWN protocols (#5853) - * Add command SetOption39 1..255 to control CSE7766 (Pow R2) or HLW8032 (Blitzwolf SHP5) handling of power loads below 6W. Default setting is 128 (#5756) - * Add command SetOption40 0..250 to disable button functionality if activated for over 0.1 second. Needs SetOption1 1 and SetOption13 0 (#5449) - * Add command SetOption63 0/1 to disable relay state feedback scan at restart (#5594, #5663) - * Add command SetOption64 0/1 to switch between "-" or "_" as sensor index separator impacting DS18X20, DHT, BMP and SHT3X sensor names (#5689) - * Add command SetOption65 0/1 and more Tuya Serial based device support (#5815) - * Add command WebColor to change GUI colors on the fly - * Add support for AWS IoT with TLS 1.2 on core 2.4.2 and up. Full doc here: https://github.com/arendst/Tasmota/wiki/AWS-IoT - * Add support for Badger HR-E Water Meter (#5539) - * Add support for Shelly 2.5 Energy and overtemp Monitoring (#5592) - * Add support for color and colortone for Philips Hue emulation via Alexa (#5600 #4809) - * Add support for Scripts as replacement for Rules. Default disabled but can be enabled in my_user_config.h (#5689) - * Add support for up to four LEDs related to four power outputs. Enabled when "LedLink(i)" is configured too (#5709) - * Add support for Shelly 1PM Template {"NAME":"Shelly 1PM","GPIO":[56,0,0,0,82,134,0,0,0,0,0,21,0],"FLAG":2,"BASE":18} (#5716) - * Add support for SPS30 Particle sensor thanks to Gerhard Mutz (#5830) - * Add support for VL53L0x time of flight sensor. Might interfere with TSL2561 using same I2C address (#5845) - * Add support for Sonoff L1 thanks to reef-actor (#6002) - * Add rule Http#Initialized - * Add rule System#Save executed just before a planned restart - * Add rule support for single JSON value pair like {"SSerialReceived":"on"} by expanding it to {"SSerialReceived":{"Data":"on"}} allowing for trigger SSerialReceived#Data=on (#5638) - * Add define USE_COUNTER to my_user_config.h to save space in sonoff-basic.bin and sonoff-minimal.bin - * Add define USE_DHT to my_user_config.h to save space in sonoff-basic.bin - * Add defines USE_EMULATION_WEMO and USE_EMULATION_HUE to my_user_config.h to control emulation features at compile time (#5826) - * Add Toggle functionality to button double press when more devices are detected - * Add device OverTemp (>73 Celsius) detection to Energy Monitoring devices with temperature sensor powering off all outputs - * Add Tuya Dimmer 10 second heartbeat serial packet required by some Tuya dimmer secondary MCUs - * Add all temperature, humidity and pressure for global access - * Add validation check when loading settings from flash - * Add HX711 weight restore after controlled restart or after power restore just before executing command Sensor34 7 (#5367, #5786) - * Add GUI hexadecimal color options in my_user_config.h (#5586) - * Add alternative IRSend command syntax IRSend raw,,
,
,,,, (#5610) - * Add user configurable ADC0 to Module and Template configuration compatible with current FLAG options (#5671) - * Add AriLux RF control GPIO option "ALux IrSel" (159) replacing "Led4i" (59) for full LED control (#5709) - * Add LED GPIO option "LedLink" (157) and "LedLinki" (158) to select dedicated link status LED (#5709) - * Add all 5 PWM channels individually adressable with LEDs. (#5741) - * Add reset of Energy values when connection to sensor is lost for over 4 seconds (#5874, #5881) - * Add checkbox to GUI password field enabling visibility during password entry only (#5934) - * - * 6.5.0 20190319 - * Remove commands SetOption14 and SetOption63 as it has been superseded by command Interlock - * Remove command SetOption35 0-255 for mDNS start-up delay (#4793) - * Remove support for MQTT_LIBRARY_TYPE, MQTT_ARDUINOMQTT and MQTT_TASMOTAMQTT (#5474) - * Change webserver content handling from single String to small Chunks increasing RAM - * Change code use of boolean to bool and byte to uint8_t - * Change code uint8_t flags to bool flags - * Change sonoff_template.h layout regarding optional module flags like ADC0 - * Change sonoff_template.h module lay-out by removing non-configurable GPIOs - * Change button driver making it modular - * Change switch driver making it modular and introduce input filter (#4665, #4724) - * Change switch input detection by optimizing switch debounce (#4724) - * Change web authentication (#4865) - * Change image name BE_MINIMAL to FIRMWARE_MINIMAL and USE_xyz to FIRMWARE_xyz (#5106) - * Change GUI weblog from XML to plain text solving possible empty screens (#5154) - * Fix most compiler warnings - * Fix Display exception 28 when JSON value is nullptr received - * Fix epaper driver (#4785) - * Fix HAss Sensor Discovery Software Watchdog restart (#4831, #4988) - * Fix allowable MAX_RULE_VARS to 16 (#4933) - * Fix mDNS addService (#4938, #4951) - * Fix HAss discovery of MHZ19(B) sensors (#4992) - * Fix some exceptions and watchdogs due to lack of stack space (#5215) - * Fix GUI wifi password acception starting with asteriks (*) (#5231, #5242) - * Fix command WebSend intermittent results (#5273, #5304) - * Fix additional characters in fallbacktopic, hostname and mqttclient on core 2.5.0 (#5359, #5417) - * Fix Energy TotalStartTime when commands EnergyReset0 and/or EnergyReset3 used (#5373) - * Fix DS18S20 temperature calculation (#5375) - * Fix float calculations in range from 0 to -1 (#5386) - * Fix exception on GUI Configure Logging and Configure Other (#5424) - * Add commands PowerCal, VoltageCal and CurrentCal for HLW8012, HJL01 and BL0937 based energy sensors - * Add command SerialDelimiter 128 to filter reception of only characters between ASCII 32 and 127 (#5131) - * Add command SSerialSend5 \ to SerialBridge - * Add command Interlock 0 / 1 / 1,2 3,4 .. to control interlock ON/OFF and add up to 8 relays in 1 to 4 interlock groups (#4910, #5014) - * Add command Template 255 to copy module configuration over to current active template and store as user template named Merged (#5371) - * Add command WifiConfig 7 to allow reset of device in AP mode without admin password (#5297) - * Add command SetOption36 to control boot loop default restoration (#4645, #5063) - * Add command SetOption37 for RGBCW color mapping (#5326) - * Add command SetOption55 0/1 and define MDNS_ENABLE to disable/enable mDNS (#4793, #4923) - * Add command SetOption62 0/1 to disable retain on Button or Switch hold messages (#5299) - * Add support for Smanergy KA10 Smart Wall Socket with Energy monitoring - * Add support for commands in sensor drivers - * Add support for MAX31855 K-Type thermocouple sensor using softSPI (#4764) - * Add support for Near Field Communication (NFC) controller PN532 using Serial (#4791, #5162) - * Add support for OBI Power Socket 2 (#4829) - * Add support for YTF IR Bridge (#4855) - * Add support for Mi LED Desk Lamp with rotary switch (#4887) - * Add support for Digoo DG-SP202 Smart Socket with Energy monitoring (#4891) - * Add support for MAX44009 Ambient Light sensor (#4907) - * Add support for inverted buttons and inverted buttons without pullup (#4914) - * Add support for Luminea ZX2820 Smart Socket with Energy monitoring (#4921) - * Add support for multiple ADS1115 I2C devices (#5083) - * Add support for online template change using command Template or GUI Configure Other (#5177) - * Add support for Korean language translations (#5344) - * Add support for sensor SCD30 (#5434) - * Add parameter CFG_HOLDER to status 1 message (#5206) - * Add SetOption32 until SetOption49 diagnostic information to Status 3 report as replacement for second property value in SetOption property name - * Add Resolution property to Status 3 report providing previous SetOption second value property - * Add property MqttCount to status 6 message representing number of Mqtt re-connections - * Add property LinkCount to state and status 11 message representing number of Wifi Link re-connections - * Add property Downtime to state and status 11 message representing the duration of wifi connection loss - * Add variable %timestamp% to rules (#4749) - * Add rule support for "==", "!=" ">=" and "<=" (#5122) - * Add rule expression enabled by define USE_EXPRESSION in my_user_config.h (#5210) - * Add Power status functionality to LED2 when configured leaving LED1 for Link status indication - * Add user configuration of HLW8012 and HJL-01/BL0937 Energy Monitoring as used in Sonoff Pow and many Tuya based devices - * Add user configuration of MCP39F501 Energy Monitoring as used in Shelly2 - * Add online template configuration using both commands and Configure Template menu option in GUI - * Add (S)SerialSend3 escape sequence \x to allow hexadecimal byte value (#3560, #4947) - * Add define DS18B20_INTERNAL_PULLUP to select internal input pullup when only one DS18B20 sensor is connected eliminating external resistor (#4738) - * Add button control when no relay configured (#4682) - * Add startup delay of 4 seconds to button control (#4829) - * Add core version conditional compile options to provided PWM files (#4917) - * Add resiliency to saved Settings (#5065) - * Add MHZ19 Temperature as Domoticz Temperature selection (#5128) - * Add HAss status sensor (#5139) - * Add status message to former declined group commands (#5145) - * Add 0x to IRRemote (SetOption29) and RCSwitch (SetOption28) received hexadecimal data (#5431) - * - * 6.4.1 20181224 - * Change RAM usage BMP/BME I2C sensors - * Change FallbackTopic from cmnd// to cmnd/_fb/ to discriminate from Topic (#1528) - * Change FallbackTopic detection (#4706) - * Change Hass discovery to short MQTT messages as used by Hass 0.81 and up (#4711) - * Change MQTT GUI password handling (#4723) - * Fix possible dtostrf buffer overflows by increasing buffers - * Fix wifi strongest signal detection (#4704) - * Fix Alexa "this value is outside the range of the device". Needs power cycle and Alexa deletion/discovery cycle. (#3159, #4712) - * Add Slovak language file (#4663) - * Add support for AZ-Instrument 7798 CO2 meter/datalogger (#4672) - * Add define WIFI_SOFT_AP_CHANNEL in my_user_config.h to set Soft Access Point Channel number between 1 and 13 as used by Wifi Manager web GUI (#4673) - * Add define USE_MQTT_TLS_CA_CERT for checking MQTT TLS against root ca using Let's Encrypt cert from sonoff_letsencrypt.h - not supported with core 2.3.0 (#4703) - * - * 6.4.0 20181217 - * Change GUI Configure Module by using AJAX for data fetch to cut page size (and memory use) by 40% - In case of web page errors clear your browser cache or do Page Reload (F5 or Ctrl+R) - * Change enforcing flashmode dout but it is still mandatory - * Change bootcount update (being first) flash write to 10 seconds after restart - * Change display and epaper drivers - * Change command WebSend Host header field from IP address to hostname (#4331) - * Change log buffer size from 512 to 520 to accommodate http sensor data (#4354) - * Change default WIFI_CONFIG_TOOL from WIFI_WAIT to WIFI_RETRY in my_user_config.h (#4400) - * Change webgui refresh time delay for Save Settings and local OTA Upload (#4423) - * Change SR-04 driver to use NewPing library (#4488) - * Change MCP230xx driver to support interrupt retention over teleperiod (#4547) - * Change support for MPU6050 using DMP (#4581) - * Fix unintended function overload of WifiState - * Fix wifi connection errors using wifi disconnect and ESP.reset instead of ESP.restart - * Fix Sonoff Pow R2 and Sonoff S31 Serial interface hang caused by Sonoff Basic R2 driver delay implementation (and possibly core bug) - * Fix MQTT connection error after restart - * Fix wifi re-scan connection baseline - * Fix possible strncat buffer overflows - * Fix intermittent Pzem sensor energy overflow calculation error - * Fix shelly2 ghost switching caused by lack of pull-up inputs (#4255) - * Fix hardware serial pin configuration. To keep using hardware serial swap current Rx/Tx pin configuration only (#4280) - * Fix MqttRetry values above 255 seconds (#4424) - * Fix WifiManager functionality on initial installation (#4433) - * Fix ArduinoOTA for Core 2.5.0 (#4620) - * Add minutes to commands Timezone to allow all possible world timezones - * Add more strict checks for GPIO selections - * Add code image and optional commit number to version - * Add dynamic delay to main loop providing time for wifi background tasks - * Add additional start-up delay during initial wifi connection - * Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver - * Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver - * Add user definition of defines WIFI_RSSI_THRESHOLD (default 10) and WIFI_RESCAN_MINUTES (default 44) - * Add command SetOption58 0/1 to enable IR raw data info in JSON message (#2116) - * Add command IRSend |0,,,.. to allow raw data transmission (#2116) - * Add command SetOption56 0/1 to enable wifi network scan and select highest RSSI (#3173) - * Add command SetOption57 0/1 to enable wifi network re-scan every 44 minutes with a rssi threshold of 10 to select highest RSSI (#3173) - * Add support for SDM220 (#3610) - * Add default sleep 1 to sonoff-basic to lower energy consumption (#4217) - * Add wifi status to Tuya (#4221) - * Add delays to reduce CPU usage at boot time (#4233) - * Add command SetOption24 0/1 to select pressure unit as hPa or mmHg (#4241) - * Add optional hardware serial when GPIO13(Rx) and GPIO15(Tx) are selected removing hardware serial from GPIO01(Tx) and GPIO03(Rx) (#4288) - * Add support for Gosund SP1 v2.3 Power Socket with Energy Monitoring (#4297) - * Add support for Armtronix dimmers. See wiki for info (#4321) - * Add to command WebSend option to send a direct path when command starts with a slash (#4329) - * Add support for LG HVac and IrRemote (#4377) - * Add initial support for Hass sensor discovery (#4380) - * Add support for Fujitsu HVac and IrRemote (#4387) - * Add support for I2C MGC3130 Electric Field Effect sensor by Christian Baars (#3774, #4404) - * Add command CalcRes to set number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE (#4420) - * Add CPU average load to state message (#4431) - * Add command SetOption59 0/1 to change state topic from tele/STATE to stat/RESULT (#4450) - * Add support for SM Smart Wifi Dimmer PS-16-DZ (#4465) - * Add support for Teckin US Power Socket with Energy Monitoring (#4481) - * Add command SetOption60 0/1 to select dynamic sleep (0) or sleep (1) (#4497) - * Add support for iFan02 Fanspeed in Domoticz using a selector (#4517) - * Add support for GPIO02 for newer Sonoff Basic (#4518) - * Add Announce Switches to MQTT Discovery (#4531) - * Add support for Manzoku Power Strip (#4590) - * - * 6.3.0 20181030 - * Change web Configure Module GPIO drop down list order for better readability - * Change status JSON message providing more switch and retain information - * Change xsns_17_senseair.ino to use TasmotaModbus library - * Change MCP230xx driver - * Change PubSubClient Mqtt library to non-blocking EspEasy version - * Change energy monitoring using energy sensor driver modules - * Change Webserver page handler for easier extension (thx to Adrian Scillato) - * Change pinmode for no-pullup defined switches to pullup when configured as switchmode PUSHBUTTON (=3 and up) (#3896) - * Change default OTA Url to http://thehackbox.org/tasmota/release/sonoff.bin (#4170) - * Remove support for MQTT Client esp-mqtt-arduino by #define MQTT_LIBRARY_TYPE MQTT_ESPMQTTARDUINO - * Remove commands PowerCal, VoltageCal and CurrentCal as more functionality is provided by commands PowerSet, VoltageSet and CurrentSet - * Remove restart after ntpserver change and force NTP re-sync (#3890) - * Fix showing Period Power in energy threshold messages - * Fix header file execution order by renaming user_config.h to my_user_config.h - * Fix some TSL2561 driver issues (#3681) - * Fix KNX PA exception. Regression from 6.2.1 buffer overflow caused by subStr() (#3700, #3710) - * Fix setting and getting color temperature for Philips Hue emulation (#3733) - * Fix ButtonRetain to not use default topic for clearing retain messages (#3737) - * Fix syslog when emulation is selected (#2109, #3784) - * Fix rule trigger POWER1#STATE execution after restart and SetOption0 is 0 (#3856) - * Fix Home Assistant forced light discovery (#3908) - * Fix invalid configuration restores and decode_config.py crc error when savedata = 0 (#3918) - * Fix timer offset -00:00 causing 12:00 hour offset (#3923) - * Fix I2CScan invalid JSON error message (#3925) - * Fix exception when wrong Domoticz JSON message is received (#3963) - * Fix Sonoff Bridge RfRaw receive (#4080, #4085) - * Fix possible wifi connection error (#4044, #4083) - * Fix invalid JSON floating point result from nan (Not a Number) and inf (Infinity) into null (#4147) - * Fix rule mqtt#connected trigger when mqtt is disabled (#4149) - * Add support for LCD, Matrix, TFT and Oled displays - * Add support for Neo Coolcam Wifi Smart Power Plug - * Add support for Michael Haustein ESP Switch - * Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT - * Add support for Neo Coolcam Wifi Smart Power Plug - * Add support for Michael Haustein ESP Switch - * Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT - * Add support for DS3231 Real Time Clock - * Add support for HX711 Load Cell with optional web GUI scale interface to demonstrate easy GUI plug-in - * Add support for serial 8N2 communication to TasmotaModbus and TasmotaSerial libraries - * Add support for RF transceiving using library RcSwitch (#2702) - * Add support for Shelly 1 and Shelly 2 (#2789) - * Add support for La Crosse TX20 Anemometer (#2654, #3146) - * Add support for MP3 player using DFRobot RB-DFR-562 (#3723) - * Add Support for Xiaomi-Philips Bulbs (#3787) - * Add support for PCA9685 12bit 16pin hardware PWM driver (#3866) - * Add support for EXS Relay V5.0 (#3810) - * Add support for OBI Power Socket (#1988, #3944) - * Add support for Teckin Power Socket with Energy Monitoring (#3950) - * Add support for Pzem-003/017 DC Energy monitoring module (#3694) - * Add support for Pzem-014/016 AC Energy monitoring module (#3694) - * Add support for CSL Aplic WDP 303075 Power Socket with Energy Monitoring (#3991, #3996) - * Add support for Tuya Dimmer (#469, #4075) - * Add command Display to show all settings at once - * Add command SerialSend5 to send raw serial data like "A5074100545293" - * Add command WebRefresh 1000..10000 to control web page refresh in milliseconds. Default is 2345 - * Add command WeightRes 0..3 to control display of decimals for kilogram - * Add command RGBWWTable to support color calibration (#3933) - * Add command Reset 4 (reset to defaults but keep wifi params) and Reset 5 (as reset 4 and also erase flash) (#4061) - * Add command SetOption35 0..255 (seconds) to delay mDNS initialization to control possible Wifi connect problems - * Add command SetOption52 0/1 to control display of optional time offset from UTC in JSON messages (#3629, #3711) - * Add command SetOption53 0/1 to toggle gui display of Hostname and IP address (#1006, #2091) - * Add authentication to HTTP web pages - * Add decimals as input to commands PowerSet, VoltageSet and CurrentSet - * Add tools/decode-config.py by Norbert Richter to decode configuration data. See file for information - * Add define USE_DISPLAYS for selecting image sonoff-display - * Add define USE_BASIC for selecting image sonoff-basic without most sensors - * Add auto reload of main web page to some web restarts - * Add TasmotaModbus library as very basic modbus wrapper for TasmotaSerial - * Add more API callbacks and document API.md - * Add Apparent Power and Reactive Power to Energy Monitoring devices (#251) - * Add token %hostname% to command FullTopic (#3018) - * Add Wifi channel number to state message (#3664) - * Add user configurable GPIO02 and GPIO03 on H801 devices (#3692) - * Add toggle function RGBW lights (#3695, #3697) - * Add network information to display start screen (#3704) - * Add sleep to Nova Fitness SDS01X sensor (#2841, #3724, #3749) - * Add Analog input AD0 enabled to sonoff-sensors.bin (#3756, #3757) - * Add power value below 5W to Sonoff Pow R2 and S31 (#3745) - * Add RF Receiver control to module MagicHome to be used on Arilux LC10 (#3792) - * Add userid/password option to decode-status.py (#3796) - * Add delay after restart before processing rule sensor data (#3811) - * Add force_update to Home Assistant discovery (#3873) - * Add rule triggers SWITCH1#BOOT and POWER1#BOOT (#3904, #3910) - * Add Hebrew language file (#3960) - * Add TotalStartTime to Energy JSON message (#3971) - * Add whitespace removal from RfRaw and SerialSend5 (#4020) - * Add support for two BMP/BME sensors (#4195) - * - * 6.2.1 20180905 - * Fix possible ambiguity on command parameters if StateText contains numbers only (#3656) - * Fix Wemo emulation to select the first relay when more than one relay is present (#3657) - * Fix possible exception due to buffer overflow (#3659) - * Fix lost energy today and total energy value after power cycle (#3689) - * - * 6.2.0 20180901 - * Allow user override of define MAX_RULE_VARS and MAX_RULE_TIMERS (#3561) - * Disable wifi sleep for both Esp8266/Arduino core 2.4.1 and 2.4.2 to solve device freeze caused by Espressif SDK bug (#3554) - * Change DS18B20 driver to provide better instant results - * Change some sensor drivers to provide instant results - * Change define USE_ALL_SENSORS to USE_SENSORS as it doesn't contain all sensors due to duplicate I2C addresses - * Change some sensor update timings: AdcEvery 200 -> 250, Senseair 300 -> 250, SDM120 300 -> 250, SDM630 300 -> 250 - * Change default Wifi config option from WPS to Wifi Manager if WPS is disabled or Wifi Smartconfig if webserver is disabled or Wifi Serial input if Smartconfig is disabled - * Change SHT1x driver to provide better instant results and fix I2C interference - * Change DHT driver to provide better instant results and add decimals to DHT11 (#3164) - * Change DS18x20 driver to provide better instant results (#3169) - * Change CounterType 1 from milliseconds to microseconds (#3437) - * Change scheduler for better sleep support using Uptime, Delay, PulseTime and TelePeriod, Blinktime (#3581) - * Remove unused functionality from Sonoff-minimal to save space - * Remove WPS and SmartConfig from sonoff-minimal saving 56k code space - * Remove TSL2561 debug message and update library (#2415) - * Remove forced restart when sleep command is executed (#3554) - * Fix invalid response using more than 4 switches and domoticz - * Fix sonoff-minimal not using default settings - * Fix unsecure main webpage update - * Fix DHT driver mixing values for different sensors (#1797) - * Fix EnergyReset3 regression not clearing total energy (#2723) - * Fix rules once regression from v6.1.0 (#3198, #3226) - * Fix command Scale buffer overflow (#3236) - * Fix possible WDT due to long MQTT publish handling (#3313) - * Fix command TimeDst/TimeStd invalid JSON (#3322) - * Fix handling of default names when using names starting with shortcut character ",0,1 or 2 (#3392, #3600, #3618) - * Fix LM75AD I2C sensor detection (#3408) - * Fix iFan02 power on state (#3412, #3530) - * Fix some Pow R2 and S31 checksum errors using optimized re-sync (#3425) - * Fix SDM120 reporting wrong negative values to Domoticz (#3521) - * Fix MQTT reconnection detection when using TasmotaMqtt library (#3558) - * Fix OtaMagic when file path contains a dash (-) (#3563) - * Fix Sonoff Bridge data reception when using Portisch EFM8 firmware using in data buffer length (#3605) - * Add read sensor retry to DS18B20, DS18x20, DHT, SHT1X and HTU21 - * Add user selection of Wifi Smartconfig as define USE_SMARTCONFIG in user_config.h - * Add boot loop detection and perform some solutions - * Add wifi and mqtt status led blinkyblinky to be disabled by SetOption31 1. Does not work when LedPower is On (deliberate) (#871, #2230, #3114, #3155) - * Add support for TM1638 switch (#2226) - * Add GPIO options ButtonXn, SwitchXn and CounterXn to select INPUT mode instead of INPUT_PULLUP (#2525) - * Add support for APDS9960 proximity sensor (#3051) - * Add support for MPR121 controller in input mode for touch buttons (#3142) - * Add support for MCP230xx for general purpose input expansion and command Sensor29 (#3188) - * Add default Wifi Configuration tool as define WIFI_CONFIG_NO_SSID in user_config.h if no SSID is configured (#3224) - * Add command Timers 0/1 to globally disable or enable armed timers (#3270) - * Add support for CCS811 sensor (#3309) - * Add Turkish language file (#3332) - * Add command SerialSend4 to send binary serial data (#3345) - * Add initial support for sensor MPU6050 (#3352) - * Add rule triggers Wifi#Connected and Wifi#Disconnected (#3359) - * Add option + to command Rule to concatenate new rule with existing rules (#3365) - * Add message when JavaScript is not enabled in webbrowser (#3388) - * Add build time setting of ButtonTopic and SwitchTopic (#3414) - * Add iFan02 Fanspeed + and Fanspeed - command options (#3415) - * Add Individual HSBColorX commands (#3430, #3615) - * Add output support on MCP23008/MCP23017 (#3436) - * Add modulo option to rules like rule1 on Time#Minute|5 do backlog power on;delay 200;power off endon (#3466) - * Add RGB support for Domoticz (#3547) - * Add all ruletimer values to command RuleTimer result message (#3571) - * Add command Publish2 for publishing retained MQTT messages (#3593) - * Add commands ButtonDebounce 40..1000 and SwitchDebounce 40..1000 to have user control over debounce timing. Default is 50mS (#3594) - * Add RuleX debug options 8,9,10 (StopOnError) to control RuleX execution status after an exception restart (#3607) - * Add rule variables %sunrise%, %sunset%, %uptime% and %time% (#3608) - * Add optional MQTT_TELE_RETAIN to Energy Margins message (#3612, 3614) - * - * 6.1.1 20180714 - * Revert wifi changes (#3177) - * Revert sonoff-minimal removals causing failure of wifi connection (#3177) - * - * 6.1.0 20180706 - * Remove version 3, 4 and pre 5.2 settings auto-upgrade. See https://github.com/arendst/Tasmota/wiki/Upgrading#migration-path - * Change default CFG_HOLDER from 0x20161209 to 4617 (=0x1209) - no impact on default upgrades - * Change number of supported switches from 4 to 8 (#2885, #3086) - * Change BME680 driver from Adafruit to Bosch BME680 library (#2969) - * Fix Pzem004T checksum error - * Fix KNX bug when doing reply of sensors values - * Fix rules induced LWT message - * Fix possible wifi connection problem (#1366) - * Fix some Pow R2 and S31 checksum errors (#1907) - * Fix display selection of un-available GPIO options in Module Configuration webpage (#2718) - * Fix timer re-trigger within one minute after restart (#2744) - * Fix IRSend not accepting data value of 0 by David Conran (#2751) - * Fix vars on rules by Adrian Scillato (#2769) - * Fix bug in KNX menu by Adrian Scillato (#2770) - * Fix anomalies in rules (#2778) - * Fix HUE bridge V1 software version by Heiko Krupp (#2788) - * Fix Hardware Watchdog restart when using event command (#2853) - * Add Ukrainian language file - * Add KNX support for DS18S20 Temperature sensor - * Add CRC to Settings making future upgrades more fail-safe - * Add feature information to Status 4 - * Add tools folder with python script decode-status.py for decoding some status fields like SetOption and Features - * Add Slots on the KNX Web Menu to select Group Addess to receive data to trigger rules - * Add two rule sets of 511 characters using commands rule1, rule2 and rule3 - * Add Console Commands to send KNX Commands and KNX Values - * Add Slots on the KNX Web Menu to select Group Addess to send data from console commands - * Add Events to trigger rules when a command or read requests is received from KNX - * Add command SetOption30 to enforce Hass discovery as light group (#1784) - * Add support for BlitzWolf BW-SHP2 (and Homecube, Gosund SP1) Energy Monitoring Smart Socket (#2223) - * Add time in minutes to rule Time#Initialized, Time#set and Time#Minute (#2669) - * Add Eastron SDM630 energy meter by Gennaro Tortone (#2735) - * Add KNX communication enhancement by Adrian Scillato (#2742) - * Add KNX energy data by Adrian Scillato (#2750) - * Add rule support for IrReceive and RfReceive (#2758) - * Add python script fw-server.py in tools folder to create a simple OTA server by Gennaro Tortone (#2759) - * Add rule variables %time% for minutes since midnight, %uptime%, %sunrise% and %sunset% giving time in minutes (#2669) - * Add rules %mem1% to %mem5% variable names storing data in flash (#2780) - * Add rules test on %varx% or %memx% (#2780) - * Add optional token %id% substituting the unique MAC address to fulltopic by Michael Graf (#2794) - * Add support for Sonoff S26 Smart Socket (#2808) - * Add command WebSend [(:,:)] (#2821) - * Add increment and decrement value to command Counter (#2838) - * Add support for Sonoff iFan02 as module 44 introducing command FanSpeed 0..3 (#2839) - * Add source information to command execution to be shown with logging option 3 (#2843) - * Add support for uploading Sonoff Bridge firmware found in tools/fw_efm8bb1 folder build by Portisch using Web Gui File Upload (#2886) - * Add command RfRaw to control Portisch firmware features - * Add support for I2C temperature sensor LM75AD (#2909) - * Add option 0 to command Timers disarming all timers (#2962) - * Add performance improvement when updating multiple individual WS2812 pixels (#3007) - * Add command SetOption28 to switch between hex or decimal Sonoff Bridge RF received data format (#3008) - * Add command SetOption29 to switch between hex or decimal IR received data format - * Add decimal values support for commands ADD, SUB, MULT and SCALE (#3083, #3089) - * Add support for bitflags SetOption50 .. SetOption81 (#3118) - * - * 5.14.0 20180515 - * Update language files - * Update TasmotaSerial to 2.0.0 allowing Hardware Serial Fallback when correct connections are configured - * Change command handling - * Change user_config(_override).h defines TIME_STD and TIME_DST - * Change user_config(_override).h otaurl to http://sonoff.maddox.co.uk/tasmota/sonoff.bin (#2588, #2602) - * Fix configuration restore regression from 5.13.1 - * Fix compile error when ADC is enabled and Rules are disabled (#2608) - * Fix rule power trigger when no backlog command is used (#2613) - * Fix several timer data input and output errors (#2597, #2620) - * Fix KNX config error (#2628) - * Fix sensor MHZ-19 vanishing data over time (#2659) - * Fix KNX reconnection issue (#2679) - * Fix DST and STD time for Southern Hemisphere by Adrian Scillato (#2684, #2714) - * Add Portuguese in Brazil language file - * Add SetOption26 to enforce use of indexes even when only one relay is present (#1055) - * Add support for sensor SI1145 UV Index / IR / Visible light (#2496) - * Add rule state test for On/Off in addition to 0/1 (#2613) - * Add hardware serial option to MHZ-19 sensor (#2659) - * Add Eastron SDM120 energy meter by Gennaro Tortone (#2694) - * Add user entry DST/STD using commands TimeStd and TimeDst (See wiki for parameter syntax) (#2721) - * - * 5.13.1 20180501 - * Fix JSON buffers size too small for execution in some situations (#2580) - * Fix configuration restore (#2591) - * Add define MODULE for user selecting default model although it preferably should not be changed (#569, #2589) - * - * 5.13.0 20180430 - * Change platformio option sonoff-ds18x20 to sonoff-allsensors enabling ds18x20 and all other sensors in one image - * Change status display of Ssid and SetOption - * Change default option SetOption15 from 0 to 1 providing better initial PWM experience - * Change webpage parameter communication - * Change max number of commands in Backlog from 15 to 30 and ignore commands overflowing - * Change TSL2561 driver to joba library and delete Adafruit library (#1644) - * Change default parameters in user_config.h to undefined for easy installation (#1851) - * Change max user configurable hold time from 10 to 25 seconds (#1851) - * Change Sonoff SC JSON format (#1939) - * Change Polish language to using Diacritics (#2005) - * Change user_config_override usage by providing user_config_override_sample.h (#2228) - * Change MQTT response topic for Energy changes from ENERGY to SENSOR (#2229, #2251) - * Change default Reset configuration time from 4 seconds to 40 seconds on Button hold (#2268) - * Change ESP8266 Analog JSON message from {"Analog0:123"} to {"ANALOG":{"A0:123"}} to accomodate rules (#2560) - * Change Counter JSON message from {"Counter1":0,"Counter3":0} to {"COUNTER":{"C1":0,"C3":0}} to accomodate rules - * Change ADS1115 JSON message from {"ADS1115":{"Analog0":123,"Analog1":123}} to {"ADS1115":{"A0":123,"A1":123}} - * Fix intermittent exception when dns lookup is used while sleep is enabled - * Fix 5.4.0 regression turning off single press after button hold during 4x hold time - * Fix possible wifi connection problem by erasing sdk configuration parameters - * Fix NTP sync to Thu Jan 01 08:00:10 1970 results in uptime 17651+ days (core2.4.1/sdk2.2.1) - * Fix MAX31850 higher temperatures (#1269) - * Fix freeing more code space when emulation is disabled (#1592) - * Fix providing web page configuratin option for Friendly Name when no device (relay or light) is configured (#1850) - * Fix compile error when define HOME_ASSISTANT_DISCOVERY_ENABLE is not set (#1937) - * Fix MQTT TLS fingerprint validation (#2033) - * Fix update temperature on DS18x20 drivers (#2328) - * Fix compile error when not defined USE_TIMERS (#2400) - * Fix configuration filename truncation when it contains spaces (#2484, #2490) - * Fix Energy Today and Yesterday overflow (#2543) - * Add serial debug info - * Add Portuguese language file - * Add Czech language file - * Add Bulgarian language file - * Add Domoticz dust (custom) sensors to PMS5003 and NovaFitness SDS drivers as PM1, PM2.5 and PM10 - * Add commands Publish, Rule, RuleTimer and Event. See Wiki about Rule restriction, usage and examples - * Add sonoff-classic, sonoff-allsensors and sonoff-knx - * Add some coloring to important web buttons - * Add support for sensor HC-SR04 ultrasonic (#113, #1964, #2444) - * Add define MQTT_TELE_RETAIN compile option default set to 0 (#1071) - * Add 16 timers using commands Timer and Timers (#1091) - * Add optional Timer configuration webpage to be enabled in user_config.h with define USE_TIMERS_WEB - * Add Multichannel Gas sensor using MultiChannel_Gas_Sensor library (#1245) - * Add Domoticz Battery and RSSI Quality (#1604) - * Add command HSBColor Hue,Sat,Bri (#1642, #2203) - * Add compile time support for WS2812 BRG and RBG led configurations to be defined in user_config.h (#1690) - * Add optional usage of %d or %X suffices in MQTT client to append chipid (#1871) - * Add optional usage of %d or %X suffices in MQTT topic to append chipid (#1871) - * Add optional usage of %d or %04d in ota url to be replaced with chipid (#1871) - * Add Sonoff Bridge command RfKey 5 to show current RF key values either default or learned (#1884) - * Add user configurable serial GPIOs to MagicHome and Arilux modules (#1887) - * Add Russian language file (#1909) - * Add Webserver upload preflight request support (#1927) - * Add Home Assistant clear other device (#1931) - * Add Restart time to Status 1 (#1938) - * Add optional TSL2561 driver using library Joba_Tsl2561 to be enabled in user_config.h with define USE_TSL2561_JOBA (#1951) - * Add support for sensor SHTC3 (#1967) - * Add compiler check for stable lwIP version v1.4 (#1940) - * Add support for multiple SHT3X sensors (#1949, #2110) - * Add always suffix with device number in Mqtt discovery topic (#1962) - * Add support for optional MQTT drivers to be selected in user_config.h (#1992) - * Add optional Arduino OTA support to be enabled in user_config.h (#1998) - * Add diacritics to Polish language file (#2005) - * Add Hungarian language file (#2024) - * Add support for Nova Fitness SDS011 and possibly SDS021 particle concentration sensor (#2070) - * Add single decimal precision to Nova Fitness SDS0x1 sensor values (#2093) - * Add Chinese (Traditional) in Taiwan language file (#2108) - * Add Sonoff SC domoticz support for Sound level as Counter and Air quality (#2118) - * Add a second TLS fingerprint to allow switching keys in TLS mode (#2033, #2102) - * Add display of remaining pulse time to command PulseTime (#2085) - * Add additional time offset to Wifi Retry based on device mac address (#2089) - * Add command Color6 RRGGBB for Clock hour marker color and command Rotation pixels for Clock rotation (#2092) - * Add HTML language header in local language (#2123) - * Add command PowerDelta 0..100 (percentage) to Energy monitoring devices to report on active power load change (#2157) - * Add Restart Reason to Status 1 report (#2161) - * Add command Channel 0..100 to control dimmer value for individual color channels (#2111, #2203) - * Add support for Hardware Serial bridge using commands SerialDelimiter, Baudrate and SerialSend. Supports 8N1 and text only (#2182) - * Add support for Software Serial bridge using commands SerialDelimiter, SBaudrate and SSerialSend. Supports 8N1 and text only (#2190) - * Add support for Zengge WF017 PWM Led strip controller (#2202) - * Add PWM status to command State if PWM enabled (#2203) - * Add all FriendlyNames to Status information (#2208) - * Add Channel status information (#2211) - * Add hexadecimal Data entry to command IrSend using 0x notation (#1290, #2314) - * Add Home Assistant MQTT Discovery for Buttons and change SetOption19 response (#2277) - * Add multiple color entry support for command Led like Led2 120000 001200 000012 setting led2 as Red, Led3 as Green and Led4 as Blue (#2303) - * Add hexadecimal RGB color entry on RGBCW leds (#2304) - * Add support for SGP30 gas and air quality sensor (#2307) - * Add optional Sunrise and Sunset timers with commands Latitide and Longitude to be enabled with define USE_SUNRISE in user_config.h (#2317) - * Add timer sunrise and sunset offset (#2378) - * Add user selectable defines for Sunrise/set Dawn option (#2378) - * Add optional KNX IP Protocol Support (#2402) - * Add random window to timers (#2447) - * Add Greek language file (#2491) - * Add support for Sonoff Pow R2 (#2340) - * Add GPIO_User to GPIO02 for all Sonoff T1 (#2524) - * - * 5.12.0 20180209 - * Change library PubSubClient.h define MQTT_MAX_PACKET_SIZE from 512 to 1000 for Home Assistant support - * Change relation of define MESSZ being dependent on PubSubClient.h define MQTT_MAX_PACKET_SIZE - * Change command color parameter input checks to less strict for Home Assistant support - * Change command Ina219Mode into command Sensor13 - * Change commands HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to be used for both Pow and S31 calibration - * Change commands HlwPSet, HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used for both Pow and S31 calibration - * Change uptime from hour to second resulting in a display of 123T13:45:21 where 123 is days - * Change module name Wemos D1 mini into Generic (#1220) - * Change HTML from width=100% to style=width:100% supporting HTML5 (#1358) - * Change OSWATCH_RESET_TIME (Blocked loop) from 30 to 120 seconds to allow slow networks (#1556) - * Change WIFI_MANAGER_SEC into WIFI_CONFIG_SEC (#1616) - * Change function pointers code to save code space and memory (#1683) - * Change webserver argument processing gaining 5k code space (#1705) - * Change weblog memory usage (#1730, #1793, #1819) - * Update TasmotaSerial library to 1.1.0 - * Update language files Italian (#1594), Dutch (#1723) and Spanish (#1722) - * Fix Non-English JSON temperature unit attachement - * Fix Arilux RF induced exception by moving interrupt handler to iram on non ESP8266/Arduino lib v2.3.0 - * Fix truncated command names and wrong response for DomoticzSwitchIdx (#1571) - * Fix %-sign issue as printf escape character in Humidity and Sonoff SC (#1579) - * Fix DS18B20 temperature JSON decimal dot (#1561) - * Fix Energy JSON message (#1621) - * Fix IRSend parameter translation (#1636) - * Fix TSL2561 device detection (#1644, #1825) - * Fix BME680 teleperiod resistance measuring (#1647) - * Fix Energy Monitoring Energy Today and Energy Total reading after restart (#1648) - * Fix IRReceive Data value (#1663) - * Fix Energy Monitoring Energy Period roll-over (#1688) - * Fix compiler warnings (#1774) - * Fix command PWM response if no PWM channel is configured (#1783) - * Add locale Decimal Separator to Web sensor page - * Add ColorTemperature to light status message - * Add command PowerOnState option 5 which inverts PulseTime and allows for delayed always on after power on - * Add OtaMagic two step Web server OTA upgrade using filename-minimal image if OTA free space is too small - * Add support for PMS5003 and PMS7003 particle concentration sensor - * Add command SetOption21 1 to allow Energy Monitoring when power is off on Sonoff Pow and Sonoff S31 (#1420) - * Add Chinese language file (#1551) - * Add French language file (#1561) - * Add Spanish language file (#1589) - * Add HTTP Allow Cross Origin removed from ESP8266/Arduino lib v2.4.0 (#1572) - * Add Home Assistant MQTT Discovery for switch and light to be enabled by command SetOption19 1 (#1534) or define HOME_ASSISTANT_DISCOVERY_ENABLE in user_config.h (#1685) - * Add command State to retrieve device state information (same data as teleperiod state and status 11 in slightly different JSON format) - * Add optional login to Webserver AP mode (#1587, #1635) - * Add command Sensor15 2 to start MHZ19(B) Zero Point Calibration (#1643) - * Add support for Sonoff S31 Smart Socket with Power Consumption Detection (#1626) - * Add command SetOption20 to allow update of Dimmer/Color/Ct without turning power on (#1719, #1741) - * Add NTP sync time slot based on chip id (#1773) - * Add cursor pointer to web button (#1836) - * - * 5.11.1 20180107 - * Fix Sonoff Pow command handling (#1542) - * - * 5.11.0 20180107 - * Minor webpage HTML optimizations (#1358) - * Updated German translation (#1438) - * Change Sonoff Pow Energy MQTT data message and consolidate Status 8 into Status 10 - * Change ADS1115 default voltage range from +/-2V to +/-6V (#1289) - * Change text to Active for 3 minutes (#1364) - * Change Wemo SetBinaryState to distinguish from GetBinaryState (#1357) - * Change output of HTTP command to valid JSON and Array only (#1363) - * Removed all MQTT, JSON and Command language defines from locale files and set fixed to English (#1473) - * Renamed commands Color2,3,4 to Color3,4,5 - * Fix BME280 calculation (#1051) - * Fix Sonoff Bridge missed learned key if learned data contains 0x55 (End of Transmission) flag (#1095, #1294) - * Fix PWM initialization in Dimmer/Color mode (#1321) - * Fix Wemo Emulation (#1357) - * Fix display of build date and time in non-english locale (#1465) - * Fix Wemo and Hue emulation by adding M-Search response delay (#1486) - * Add libraries Adafruit_BME680-1.0.5, Adafruit_Sensor-1.0.2.02, TasmotaSerial-1.0.0 and TSL2561-Arduino-Library - * Add command Color2 to set color while keeping same dimmer value - * Add device function pointers - * Add support for SenseAir S8 CO2 sensor - * Add color led signal to Carbon Dioxide (CO2) sensors using defines CO2_LOW and CO2_HIGH in user_config.h - * Add support for Domoticz Air Quality sensor to be used by MH-Z19(B) and SenseAir sensors - * Add support for PZEM004T energy sensor - * Add support for iTead SI7021 temperature and humidity sensor by consolidating DHT22 into AM2301 and using former DHT22 as SI7021 (#735) - * Add support for BME680 using adafruit libraries (#1212) - * Add support for MH-Z19(B) CO2 sensor (#561, #1248) - * Add multipress support and more user configurable GPIO to Sonoff Dual R2 (#1291) - * Add support for TSL2561 using adafruit library (#661, #1311) - * Add support for SHT3x (#1314) - * Add support for Arilux LC06 (#1414) - * Add Italian language file (#1449) - * Add 2nd Gen Alexa support to Wemo emulation discovery (#1357, #1450) - * Add define for additional number of WS2812 schemes (#1463) - * - * 5.10.0 20171201 - * Upgrade library ArduinoJson to 5.11.2 - * Upgrade library IRRemoteEsp8266 to 2.2.1 + 2 commits but disabled some protocols (code size reduction) - * Upgrade library NeoPixelBus to 2.2.9 - * Upgrade library OneWire to 2.3.3 + 6 commits and disabled CRC lookup-table (#define ONEWIRE_CRC8_TABLE 0) (code size reduction) - * Update library PubSubClient to 2.6 + 9 commits and additional delay (#790) - * Update core_esp8266_wiring_digital.c to latest (staged) level - * Patch library I2Cdevlib-Core for esp8266-core 2.4.0-rc2 compatibility - * Remove command EnergyReset 1..3 now replaced by EnergyReset1 to EnergyReset3 - * Remove spaces in JSON messages (code size reduction) - * Renamed xsns_05_ds18x20.ino to xsns_05_ds18x20_legacy.ino still using library OneWire and providing dynamic sensor scan - * Fix possible iram1_0_seg compile error by shrinking ICACHE_RAM_ATTR code usage - * Fix PWM watchdog timeout if Dimmer is set to 100 or Color set to 0xFF (#1146) - * Fix Sonoff Bridge Learn Mode hang caused by unrecognised RF code (#1181) - * Fix blank console log window by using XML character encoding (#1187) - * Fix wrong response name for command HlwISet (#1214) - * Fix DHT type sensor timeout recognition by distinguish "signal already there" from "timeout" (#1233) - * Add fixed color options 1..12 to command Color - * Add + (plus) and - (minus) to commands Dimmer (+10/-10), Speed and Scheme - * Add + (plus) and - (minus) to command Color to select 1 out of 12 preset colors - * Add + (plus) and - (minus) to command Ct to control ColdWarm led ColorTemperature (+34/-34) - * Add commands EnergyReset1 0..42500, EnergyReset2 0..42500 and EnergyReset3 0..42500000 - * to (Re)set Energy Today, Yesterday or Total respectively in Wh (#406, #685, #1202) - * Add optional ADS1115 driver as alternative for unsupported I2Cdevlib in esp8266-core 2.4.0-rc2 - * Add support for INA219 Voltage and Current sensor to be enabled in user_config.h with define USE_INA219 - * Add support for Arilux LC11 (Clearing RF home code when selecting no Arilux module) - * Add support for WS2812 RGBW ledstrips to be enabled in user_config.h with define USE_WS2812_CTYPE (#1156) - * Add SettingsSaveAll routine to command SaveData to be used before controlled power down (#1202) - * Add option PUSHBUTTON_TOGGLE (SwitchMode 7) to allow toggling on any switch change (#1221) - * Add new xdrv_05_ds18x20.ino free from library OneWire and add the following features: - * Add support for DS1822 - * Add forced setting of 12-bit resolution for selected device types (#1222) - * Add read temperature retry counter (#1215) - * Fix lost sensors by performing sensor probe at restart only thereby removing dynamic sensor probe (#1215) - * Fix sensor address sorting using ascending sort on sensor type followed by sensor address - * Rewrite JSON resulting in shorter message allowing more sensors in default firmware image: - * "DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6} - * Add additional define in user_config.h to select either single sensor (defines disabled), new multi sensor (USE_DS18X20) or legacy multi sensor (USE_DS18X20_LEGACY) - * Add clock support for more different pixel counts (#1226) - * Add support for Sonoff Dual R2 (#1249) - * Add FriendlyName to web page tab and add program information to web page footer (#1275) - * - * 5.9.1 20171107 - * Add external sensor function pointer interface to enable easy sensor addition - * Add support for ADS1115 to be enabled in user_config.h and needs libraries i2cdevlib-Core and i2cdevlib-ADS1115 (#338, #660) - * Fix Backup Configuration file download failure by defining proper file size (#1115) - * Fix Exception 26 and empty console screen after usage of command WakeupDuration (#1133) - * Fix some changed iTead web links in README.md (#1137) - * - * 5.9.0 20171030 - * Rewrite code (partly) using Google C++ Style Guide (https://google.github.io/styleguide/cppguide.html) - * Rewrite code by using command lookup tables and javascript (client side) web page expansions - * Change HTML/CSS to enable nicer form field entry - * Change default PWM assignments for H801 RGB(CW) led controller to support optional Color/Dimmer control - * GPIO04 (W2) from GPIO_PWM2 to GPIO_USER to be user configurable for GPIO_PWM5 (second White - Warm if W1 is Cold) - * GPIO12 (Blue) GPIO_PWM3 no change - * GPIO13 (Green) from GPIO_PWM4 to GPIO_PWM2 - * GPIO14 (W1) from GPIO_PWM1 to GPIO_USER to be user configurable for GPIO_PWM4 (first White - Cold or Warm) - * GPIO15 (Red) from GPIO_PWM5 to GPIO_PWM1 - * Change default PWM assignments for MagicHome RGB(W) led controller to support optional Color/Dimmer control - * GPIO05 (Green) from GPIO_PWM4 to GPIO_PWM2 - * GPIO12 (Blue) from GPIO_PWM5 to GPIO_PWM3 - * GPIO13 (White) GPIO_USER to be user configurable for GPIO_PWM4 (White - Cold or Warm) - * GPIO14 (Red) from GPIO_PWM3 to GPIO_PWM1 - * Change default PWM assignment for Witty Cloud to support optional Color/Dimmer control (#976) - * GPIO12 (Green) from GPIO_PWM4 to GPIO_PWM2 - * GPIO13 (Blue) from GPIO_PWM5 to GPIO_PWM3 - * GPIO15 (Red) from GPIO_PWM3 to GPIO_PWM1 - * Change when another module is selected now all GPIO user configuration is removed - * Change command name IRRemote to IRSend (#956) - * Remove Arduino IDE version too low warning as it interferes with platformio.ini platform = espressif8266_stage - * Fix command FullTopic entry when using serial or console interface - * Fix possible UDP syslog blocking - * Fix minimum TelePeriod of 10 seconds set by web page - * Fix command GPIOx JSON response (#897) - * Fix inverted relay power on state (#909) - * Fix compile error when DOMOTICZ_UPDATE_TIMER is not defined (#930) - * Fix alignment of web page items in some browsers (#935) - * Fix setting all saved power settings to Off when SetOption0 (SaveState) = 0 (#955) - * Fix timezone range from -12/12 to -13/13 (#968) - * Fix Southern Hemisphere TIME_STD/TIME_DST (#968) - * Fix TLS MQTT SSL fingerprint test (#970, #808) - * Fix virtual relay status message used with Color/Dimmer control (#989) - * Fix command IRSend and IRHvac case sensitive parameter regression introduced with version 5.8.0 (#993) - * Fix pressure calculation for some BMP versions regression introduced with version 5.8.0i (#974) - * Fix Domoticz Dimmer set to same level not powering on (#945) - * Fix Blocked Loop when erasing large flash using command reset 2 (#1002) - * Fix relay power control when light power control is also configured as regression from 5.8.0 (#1016) - * Fix Mqtt server mDNS lookup only when MqttHost name is empty (#1026) - * Add debug information to MQTT subscribe - * Add translations to I2Cscan - * Add translation to BH1750 unit lx - * Add light scheme options (Color cycle Up, Down, Random) and moving WS2812 schemes up by 3 - * Add Domoticz counter sensor to IrReceive representing Received IR Protocol and Data - * Add option 0 to MqttHost to allow empty Mqtt host name - * Add support for Arilux AL-LC01 RGB Led controller (#370) - * Add esp8266 de-blocking to PubSubClient library (#790) - * Add Domoticz sensors for Voltage and Current (#903) - * Add platformio OTA upload support (#928, #934) - * Add warning to webpage when USE_MINIMAL is selected (#929) - * Add smoother movement of hour hand in WS2812 led clock (#936) - * Add support for Magic Home RGBW and some Arilux Led controllers (#940) - * Add command SetOption15 0 (default) for command PWM control or SetOption15 1 for commands Color/Dimmer control to PWM RGB(CW) leds (#941) - * Add Domoticz counter sensor to Sonoff Bridge representing Received RF code (#943) - * Add support for Luani HVIO board (https://luani.de/projekte/esp8266-hvio/) (#953) - * Add PWM initialization after restart (#955) - * Add IR Receiver support. Disable in user_config.h (#956) - * Add support for inverted PWM (#960) - * Add Sea level pressure calculation and Provide command Altitude (#974) - * Add support for up to 8 relays (#995) - * Add commands RfSync, RfLow, RfHigh, RfHost and RfCode to allow sending custom RF codes (#1001) - * Add retain to ENERGY messages controlled by command SensorRetain (#1013) - * Add commands Color2, Color3, Color4, Width2, Width3, Width4 and SetOption16 to set Ws2812 Clock parameters (#1019) - * Add German language file (#1022) - * Add support for connecting to MQTT brokers without userid and/or password (#1023) - * Add support for esp8266 core v2.4.0-rc2 (#1024) - * Add commands PwmRange 1,255..1023 and PwmFrequency 1,100..4000 (#1025) - * Add Polish language file (#1044, #1047) - * Add support for KMC 70011 Power Monitoring Smart Plug (#1045) - * Add support for VEML6070 I2C Ultra Violet level sensor (#1053) - * Add light turn Off Fade (#925) - * Add IrSend command option Panasonic as IrSend {"Protocol":"Panasonic", "Bits":16388, "Data":} - * where 16388 is 0x4004 hexadecimal (#1014) - * Add retry counter to DHT11/21/22 sensors (#1082) - * - * 5.8.0 20170918 - * Remove the need for NeoPixelBus library for Hue support - * Consolidate WS2812 into Sonoff Led for flexible future led strip library changes - * Invert WS2812 fade speed to align with Sonoff led (Speed 1 = fast, Speed 8 = slow) - * Remove upper case MQTT receive buffer - * Reduce code and string length for output of commands Modules and GPIOs - * Add Sonoff SC debug information - * Change syslog service - * Removed webserver syslog disable as now no longer needed - * Increased default MQTT message size from 368 to 405 bytes while keeping MQTT_MAX_PACKET_SIZE = 512 (because we can) - * Fix MQTT Offline or Remove MQTT retained topic code - * Fix Domoticz loop when Emulation is selected - * Add blink to WS2812 and Sonoff Led (#643) - * Add option WIFI_WAIT (5) to command WifiConfig to allow connection retry to same AP without restart or update flash (#772, #869) - * Add support for Witty Cloud (#794) - * Add GPIO14 to Sonoff Dual (#797, #839) - * Add support for Yunshan Wifi Relay (#802) - * Add GPIO16 input pulldown (#827) - * Add timeout to DHT and DS18B20 sensors (#852) - * Fix watchdog timeout caused by lack of stack space by moving to heap (#853) - * Allow LogPort and MqttPort up to 65535 and add LogPort tot Status 3 (#859) - * Allow command SwitchTopic in group mode (#861) - * Allow command SwitchMode if no switches are defined (#861) - * Add optional dimmer parameter to command Wakeup for WS2812, AiLight, Sonoff B1, Led and BN-SZ01 (#867) - * Fix basic On, Off, Toggle, Blink and BlinkOff commands when other language is selected (#874) - * - * 5.7.1 20170909 - * Remove leading spaces from MQTT data - * Fix webconsole special character entry - * Allow # as prefix for color value - * Fix Alexa detection and Hue App Update Request (#698, #854) - * - * 5.7.0 20170907 - * Shrink module configuration webpage - * Fix settings order during startup to allow for displaying debug messages - * Fix some string length issues - * Add more string length tests by using strncpy - * Add Ai-Thinker RGBW led (AiLight) - * Add Power check and add PulseTime to power check at startup (#526) - * Add Supla Espablo support (#755) - * Add more precision to Sonoff Pow period and power results using command WattRes 0|1 (#759) - * Add basic internationalization and localization (#763) - * Add more Sonoff Pow range checking (#772) - * Fix invalid JSON (#786, #822) - * Add duplicate check to received RF signal within 2 seconds for Sonoff Bridge (#810) - * - * 5.6.1 20170818 - * Change module list order in webpage - * Fix Sonoff T1 1CH and 2CH configuration (#751) - * - * 5.6.0 20170818 - * Fix Sonoff Pow intermittent exception 0 - * Change Sonoff Pow sending Domoticz telemetry data only - * Add Ai-Thinker RGBW led (AiLight) (experimental) - * Add NeoPixelBus library to Sonoff Led for Hue support - * Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge - * Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676) - * Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color Temperature - * Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1 - * Add CT parameter to Hue - * Add Sonoff T1 support (#582) - * Add AnalogInput0 if configured as Analog Input to webpage (#697, #746) - * Add command SetOption14 0|1 to enable interlock mode (#719, #721) - * Fix Mitsubishi HVAC IR power controll (#740) - * - * 5.5.2 20170808 - * Extent max number of WS2812 pixels from 256 to 512 (#667) - * Add OTA handling if server responds with no update available (#695) - * Removed undocumented command FlashMode (#696) - * Fix compile time error message due to increased message buffer size (#703) - * - * 5.5.1 20170805 - * Fix Sonoff Rf Bridge issues - * Add Sonoff RF Bridge MQTT messages on received and learned RF signal - * Add command VoltRes 0|1 to select voltage resolution to 0.1 V (#654) - * Add averaging to Analog input (#686) - * Add Energy tele data on Sonoff Pow Threshold change (#688) - * Fix inconsistent property names in Messages (#690) - * - * 5.5.0 20170730 - * Reduce code space by removing the following commands as they are replaced by SetOption alternatives: - * SaveState = SetOption0 - * ButtonRestrict = SetOption1 - * Units = SetOption2 - * MQTT = SetOption3 - * MQTTResponse = SetOption4 - * TempUnit = SetOption8 - * Smoothing WS2812 animation poll, invert fade speed and max allowed wakeup time down to 3000 seconds - * Fix initial button press detection - * Add support for Sonoff RF Bridge 433 using command RfKey - * Fix regression from 5.0.7 by increasing message buffer size from 360 to 368 to accomodate 4 x DS18x20 sensors (#637) - * Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to send either ON/OFF or TOGGLE (#642) - * Adjust HLW calibration limits to accomodate HuaFan device and add commands HlwPSet, HlwUSet and HlwISet (#654) - * - * 5.4.0 20170725 - * Fix command reset regression introduced in 5.2.0 - * Increase polling from 0.1 second to 0.05 second - * Add multipress to all buttons - * Fix button 1 double press behaviour on multi relay devices - * Add support for Hua Fan Smart Socket (#479) - * Add support for Sonoff 4ch Pro (#565) - * Add command SetOption13 1 to allow immediate action on single button press - * (disables multipress, hold and unrestricted commands) (#587) - * - * 5.3.0 20170715 - * Major Hue rewrite which might introduce Alexa problems. If so, initiate an issue - * Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control to Hue - * Fix Sonoff Led Power, Dimmer and Color MQTT response (#176) - * Add commands Delay and Backlog to allow multiple commands at once separated by ";" (#593) - * Use default flashmode DOUT to solve restart hangs on esp8285 chips (#453, #598) - * Change Web console column width from 99 to 300 (#599) - * - * 5.2.4 20170703 - * Removed flash mode update after selecting different module solving esp8285 related problems - * Add device type flag to sonoff_template.ino - * Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led (#567) - * - * 5.2.3 20170630 - * Change Sonoff Led color conversion code - * Fix SetOption12 handling - * Simplify auto configuration upgrade - * Add option Upgrade to only upgrade to any higher version (Old PR #213) - * Change FallbackTopic to cmnd// bypassing FullTopic and Prefix (#538) - * - * 5.2.2 20170625 - * Add configuration SaveAddress to Status 1 and Information Page - * Change Sonoff Led Color conversion from AtoH to strtol - * Fix possible wrong uploads due to configuration overwrites (#542) - * Fix payload negative numbers (#547) - * - * 5.2.1 20170622 - * Fix Restore Configuration in case of lower version - * Revert auto configuration upgrade allowing easy upgrade which was removed in version 5.2.0 - * Fix config auto upgrade from versions below version 4.1.1 (#530) - * - * 5.2.0 20170619 - * Add command SetOption12 1 to disable newly released configuration flash rotate to reduce flash wear - * Fix command CounterDebounce by removing test for active GPIO (#524) - * Add command SetOption33 1..250 to allow user configure POW Max_Power_Retry count (#525) - * - * 5.1.7 20170616 - * Prep removal of SetOptions alternatives - * Restore webpage upgrade error messages removed in 5.1.5 - * Add hold button functionality to buttons 2 to 4 - * Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds to 10 seconds (#200) - * Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507) - * Changed webpage form actions from post to get and use relative path url (#434, #522) - * - * 5.1.6 20170606 - * Shrink code - * Removed online configuration of Domoticz In and Domoticz Out MQTT strings - * Removed commands DomoticzInTopic and DomoticzOutTopic - * Add define KEY_HOLD_TIME to configure button hold threshold before sending MQTT Hold message - * Add command StateText4 to configure button MQTT Hold text (= MQTT_CMND_HOLD) - * Add command SetOption11 0|1 to swap pushbutton single and double press functionality (#200) - * Add command SwitchMode 5 (PUSHBUTTONHOLD) and 6 (PUSHBUTTONHOLD_INV) (#489) - * - * 5.1.5 20170604 - * Shrink code in preparation to ESP8266-Arduino 2.4.0-rc1 - * Add effect parameter to HUE Device (#464) - * - * 5.1.4 20170601 - * Removed pre-compiled versions from repository as they are available within the release - * Changed HUE Device type to color supporting version (#464) - * Fix compile error when BE_MINIMAL is selected (#467, #476) - * Add multiple compiled versions to release using updated Travis script and platformio.ini (#467) - * - * 5.1.3 20170520 - * Add Domoticz Counter - * - * 5.1.2 20170519 - * Fix Counter/Timer JSON message and update Counter/Timer on webpage - * Fix WS2812 Domoticz related regression issues - * - * 5.1.1 20170517 - * Allow command FullTopic in group mode - * Prepare for more use of RTC memory - * Add independant WS2812 led string power control (#386, #390) - * Add command Counter to control up to four GPIO falling edge interrupt counters or timers (#459) - * Add command CounterType to select between pulse counting or pulse timing - * Add command CounterDebounce to select global counter debounce time in mSec - * - * 5.1.0 20170513 - * Fix Offline/Removal of retained topic when FullTopic is changed - * Add FullTopic to MQTT Configuration and Information web pages - * Add license model GPLv3 (#188) - * - * 5.0.7 20170511 - * Fix possible exception 28 on empty command - * Add command SetOption0 as replacement for SaveState - * Add command SetOption1 as replacement for ButtonRestrict - * Add command SetOption2 as replacement for Units - * Add command SetOption4 as replacement for MqttResponse - * Add command SetOption8 as replacement for TempUnit - * Add command SetOption10 On|Off to select between Offline or Removing previous retained topic (#417, #436) - * - * 5.0.6 20170510 - * Remove hyphen in case of a single DHT sensor connected (#427) - * Add command MqttRetry to change default MQTT reconnect retry timer from minimal 10 seconds (#429) - * - * 5.0.5 20170508 - * Add command FullTopic with tokens %topic% (replaced by command Topic value) and - * %prefix% (replaced by command Prefix values) for more flexible topic definitions (#244) - * See wiki > MQTT Features https://github.com/arendst/Tasmota/wiki/MQTT-Features for more information - * - * 5.0.4 20170505 - * Add Sonoff Pow Energy Total up to 40 MWh - * Add command EnergyReset 1|2|3 to reset Energy counters (#406) - * Fix Domoticz Energy logging (#411) - * Add command PowerOnState 4 to keep relay always on and disabling all power control (#418) - * - * 5.0.3 20170504 - * Add command SensorRetain on|off to enable retaining of mqtt message tele/sonoff/SENSOR (#74) - * Change WifiConfig timeout from 60 seconds to 180 seconds (#212) - * Change Sonoff Touch command Ledstate functionality by turning led on if power is off (#214) - * Add 4 seconds delay after power on before enabling button to workaround Wemos D1 mini RTS circuit (#380) - * - * 5.0.2 20170503 - * Reset SaveData, SaveState and MqttResponse to default values due to rearranging settings - * Moved some settings to flag area - * Add command TempUnit Celsius|Fahrenheit for selecting Celsius or Fahrenheit (#347) - * Add command TempRes 0..3 for selecting Temperature Resolution (#347) - * Add command HumRes 0..3 for selecting Humidity Resolution (#347) - * Add command PressRes 0..3 for selecting Pressure Resolution (#347) - * Add command EnergyRes 0..5 for selecting Energy Resolution (#347) - * Add "TempUnit":"C|F" to sensor JSON output (#347) - * Add support for up to three DHT type sensors each using a different GPIO (#339, #404) - * - * 5.0.1 20170429 - * Adjust Sonoff SC messages to prepare for display feature - * Move static data from RAM to Flash - * Fix PowerOnState for some devices not reporting "Power on" state (#284, #380, #383) - * - * 5.0.0 20170425 - * Memory status message update - * Fix setting migration to better preserve settings during move (#382) - * Best practice is first doing a Backup Configuration before installing version 5.0.0 - * Reset save count after setting move - * Start using new linker script without SPIFFS - * - * 4.2.0 20170424 - * Prepare for SPIFFS removal by moving settings to EEPROM area - * Fix compilation error when webserver is disabled (#378) - * - * 4.1.3 20170410 - * Add user configuarble GPIO to module S20 Socket and Slampher - * Add support for Sonoff SC (#112) - * Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led firmware (#122) - * Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions due to power supply instabilities (#122) - * Add Access Point Mac Address to Status 11 and Telemetry (#329) - * Fix DS18B20 negative temperature readings (#334) - * - * 4.1.2 20170403 - * Rename Unrecognised command to Unknown command - * Remove all command lists - * Remove command SmartConfig (superseded by WifiConfig) - * Fix boot loop when selecting module Sonoff 4CH or Sonoff Touch on non ESP8285 hardware - * Add optional support for Toshiba and Mitsubishi HVAC IR control (needs updated IRremote8266 library) (#83, #257) - * Add all configured switches to Domoticz Configuration web page (#305) - * Fix compile error when selecting WS2812 DMA (#313) - * - * 4.1.1 20170329 - * Fix default Telemetry for command Prefix3 - * Fix webserver Module parameters for disabled select - * Fix sensor status for enabled switches - * Remove Light as alternative for Power (save code space) - * Remove migration option from pre V3 (code cleanup) - * Remove unofficial SPIFFS support (code cleanup) - * Remove command list when unknown command is entered (save code space) - * Rename Status11 json from StatusPWR to unique StatusSTS - * Rename command Gateway to IPAddres2, Subnetmask to IPAddress3 and DnsServer to IPAddress4 (save code space) - * Add Command MqttResponse to select either command or RESULT topic as response (#258) - * Add command StateText1 to StateText3 to assign MQTT_STATUS_OFF, MQTT_STATUS_ON and MQTT_CMND_TOGGLE respectively (#286) - * Remove restart after IPAddress changes (#292) - * Add support for MAX31850 in xsns_ds18x20.ino (#295) - * Fix possible uptime update misses (#302) - * - * 4.1.0 20170325 - * Change static IP addresses in user_config.h from list (using commas) to string (using dots) - * Unify display result of commands Modules, Module and Gpios - * Rewrite Module selection web page to bring size down from 18651 to 4319 bytes (!) (#234, #240) - * Add basic support for (Lixada) H801 RGBWW controller (#252) - * Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and PUB_PREFIX2 respectively (#255) - * Add static ip addresses to flash (#262) - * Add commands IpAddress, Gateway, Subnetmask and DnsServer to select static ip addresses (#273) - * - * 4.0.8 20170321 - * Fix entering non-numeric webpassword - * Force selection between TLS or Webserver due to memory restraint (#240) - * Allow entering empty string using "0" for selected commands (#242) - * Fix exception when posting commands to web console containing % (#250) - * - * 4.0.7 20170319 - * Increased Sonoff Led PWM frequency from 432 to 1000 - * Fix possible watch dog reboot after changing module type on web page - * Fix reporting of GPIO usage from web page - * Fix Sonoff Led blank during firmware upgrade - * Fix Sonoff Led flicker and possible flash corruption by using latest Arduino-esp8266 versions - * of pwm core files included in sonoff library (#211) - * Add PWM output control with commands PWM1 to PWM5 using user selectable GPIOs (#211) - * Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal (1000) and HlwICal (2500) (#223) - * Add Switch state to sensor status (#227, #233) - * Add user configuarble GPIO to module Sonoff Touch (#228) - * Add define WEB_PORT to user_config.h to change default web server port from 80 (#232) - * Fix failed Ota Firmware upgrade started from Web page (#235) - * - * 4.0.6 20170316 - * Fix to better find device by Wifi hostname - * Fix compile error when some I2C devices are disabled - * Add (experimental) support for SHT1X emulating I2C (#97) - * Add ADC to ElectroDragon (#203) - * Add support for Sonoff Dev (#206) - * - * 4.0.5 20170314 - * Add command Status 11 to show power status with Vcc if define USE_ADC_VCC is enabled (default) - * Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with define USE_ADC_VCC disabled (#137) - * Add MQTT host:port to timeout message (#199) - * - * 4.0.4 20170312 - * Add pulse timers for up to 4 relays (#106) - * Fix Sonoff Led power state when dimmer or color is 0 (#176) - * Add command NtpServer to configure up to three NTP servers (#177) - * Delete module User Test as module Wemos D1 mini has same/more user configurable GPIO (#178) - * Add more user configurable GPIO to module ElectroDragon (#183) - * - * 4.0.3 20170309 - * Renamed Module NodeMCU to WeMos D1 mini - * Add GPIO1 as user option to some modules - * Add Buttons, Relays and Leds to user configurable options (#159) - * Add description on Module parameters web page to some well known GPIOs (#107, #171) - * - * 4.0.2 20170308 - * Restore correct seriallog level after Serial logging was disabled - * Add simple dimmer slider to Sonoff Led web page - * Reduced root webpage size by 31% - * Expand Status 2 with Build date/time and core version - * Fix webserver redirection when not in WifiManager mode (#156) - * Add command ButtonRestrict On/Off to restrict access to button hold and button multi press options above 2 (#161) - * Fix DS18S20 negative temperature readings (#165) - * Fix crlf compilation error due to bad syntax (#144, #167) - * - * 4.0.1 20170305 - * Fix char default sizes and set MESSZ to 360 (#143) - * Fix SerialLog setting status - * Disable syslog when emulation is active - * Add DS18B20 web page display refresh - * - * 4.0.0 20170303 - * Add define to remove config migration code for versions below 3.0 (See Wiki-Upgrade-Migration path) - * Free memory by switching from String to char[] - * Raised Sonoff Led PWM frequency from 200Hz to 432Hz in search of stability (hardware watchdog timeouts) (#122) - * Increase message size and suggested minimum MQTT_MAX_PACKET_SIZE to 512 (#114, #124) - * Remove runtime warning message regarding MQTT_MAX_PACKET_SIZE too small as it is now moved to compile time (#124) - * Fix possible panics with web console and http commands while UDP syslog is active (#127) - * Add optional static IP address (#129) - * Add define ENERGY_RESOLUTION in user_config.h to allow user control over precision (#136) - * - * 3.9.22 20170228 - * Update web console - * Fix Status 4 JSON message - * Add Exception info during restart if available - * Add osWatch service to detect loop hangs that might happen during (OTA) upgrades - * Add WiOn support for relay and switch only (#82, #102) - * Allow for user specified relay count up to four in sonoff_template.h (#109) - * Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021 (#118) - * Add NodeMCU or Wemos configuration option (#119) - * - * 3.9.21 20170224 - * Add ajax to web root page and web console (#79) - * Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84, #88) - * Fix MQTT upgrade when webserver is active - * - * 3.9.20 20170221 - * Add minimal basic authentication to Web Admin mode (#87) - * Fix Hue and add HSB support (#89) - * - * 3.9.19 20170219 - * Sonoff Led: Made GPIO04, 05 and 15 available for user - * Sonoff Led: Add commands Fade, Speed, WakupDuration, Wakeup and LedTable - * - * 3.9.18 20170218 - * Fix ledstate 0 to turn off led - * Fix Sonoff Led dimmer range (#16) - * Change Sonoff Led command Dimmer to act on both cold and warm color - * Add Sonoff Led command Color CCWW where CCWW are hexadecimal values fro 00 - FF - * Reduce Sonoff Led flickering by disabling interrupts during flash save and disabling - * Led during OTA upgrade and Web upload (#16) - * - * 3.9.17 20170217 - * Fix possible ArduinoJSON related memory fragmentation - * Changed console logging using less memory - * Add GPIO04 as user selectable for Sonoff Dual (#75) - * - * 3.9.16 20170214 - * Update latching relay handler - * Add support for IR led using IRremoteESP8266 library (#59) - * Add Hue argument passing using ArduinoJSON library (#59) - * - * 3.9.15 20170213 - * Change JSON float values from string to number according to http://json.org (#56) - * Add support for exs latched relay module https://ex-store.de/ESP8266-WiFi-Relay-V31 (#58) - * Add support for inverted relays - * Changed MAX_LOG_LINES from 70 to 60 to preserve memory - * - * 3.9.14 20170211 - * Add False and True as alternatives for 0/Off and 1/On (#49) - * Fix Status10 JSON format (#52) - * Fix DS18x20 using OneWire library (#53) - * - * 3.9.13 20170210 - * Add FlashChipMode to Status 4 - * Removed redundant DHT2 option and code - * Add Sonoff SV GPIO pin 05 configuration (#40) - * Add configuration file backup and restore via web page - * Fix latency due to light_sleep mode even if sleep was set to zero (#50) - * - * 3.9.12 20170208 - * Fix compile error when webserver is disabled (#30) - * Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during OTA upload - * Fix hostname issues by not allowing user entry of string formatting and removing from user_config.h (#36) - * - * 3.9.11 20170204 - * Fix command I2Cscan - * Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic - * Make all TELEMETRY, STATUS and COMMAND message topics unique (#4) - * Advertise command topic to be used by iobroker (#299) - * Fix butten (non)detection if no GPIO_KEY1 is defined (#13) - * Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars (#18) - * Update web page with Build Date/Time, Emulation and mDNS Discovery and Advertise information (#21) - * - * 3.9.10 20170130 - * Add WS2812 Color Type selection (RGB or GRB) to user_config.h (#7) - * Hue api changes to support HUE App(s) (#8) - * - * 3.9.9 20170130 - * Add command status 10 showing sensor data - * Fix hlw status messages if hlw is disabled - * - * 3.9.8 20170130 - * Remove GPIO07 and GPIO08 from user selectable (#5) - * - * 3.9.7 20170129 - * Fix possible WS2812 exceptions when using emulation - * Add command Emulation to dynamic configure Belkin WeMo and Hue Bridge for Alexa - * - * 3.9.6 20170129 - * Add dynamic sleep for WS2812 animation (#1) - * - * 3.9.5 20170128 - * Fix error message in case of wrong Domoticz command - * - * 3.9.4 20170127 - * Fix Sonoff Dual Relay switching (#287) - * - * 3.9.3 20170127 - * Add confirmation before Restart via webpage - * Expand Domoticz Configuration webpage with Key, Switch and Sensor Index and - * add commands DomoticzSwitchIdx and DomoticzSensorIdx (#86) (#174) (#219) - * Fix default DHT11 sensor driver selection - * Fix LedPower status after button press (#279) - * Add command Sleep 0 - 250 mSec for optional light sleep mode to lower energy consumption (#272) - * (Expect overall button/key/switch misses and wrong values on Sonoff Pow) - * Add Hue brightness extension (#281) - * Fix Hue brightness and change to call by reference (#283) - * - * 3.9.2 20170124 - * Add confirmation before Reset Configuration via webpage (#244) - * Add WS2812 features (see Wiki commands) - * - * 3.9.1 20170124 - * Change PowerOnState function to only trigger when Power On (and not just restart) (#238) - * Move HLW interrupts back to RAM and make WS2812_DMA optional as it generates Exception on Pow (#264) - * Add charset=utf-8 to webpages (#266) - * Update Hue emulation (#268) - * Fix status module number - * Add support for domoticz Dimmer on Sonoff_Led and WS2812 - * Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during web upload - * - * 3.2.6a 20170120 - * Fix Sonoff Pow compile error (#255) - * Move HLW interrupts back to ROM (Needed for WS2812 DMA interrupts) - * Removed all IO config from user_config.h as this will be done by commands or webpage - * Removed MessageFormat and supports JSON only except POWER/LIGHT status - * Add command LedPower to control main led (#247) - * Add more FriendlyNames for Hue (#254) - * Add DMA support for WS2812 when using pin 3 while other pins work just as well in my case... - * Add HUE emulation for Alexa (#229) - * Add basic WS2812 support (#229) - * Fix Wemo when MQTT is disabled (#245) - * Revert ButtonTopic and change SwitchTopic1 - 4 to one SwitchTopic - * Rename MqttUnits to Units - * Add Mqtt command to enable/disable MQTT - * - * 3.2.2a 20170115 - * Add dynamic (Sonoff) Module, user GPIO and sensor selection (one size fits (almost) all) - * Add support for Sonoff LED - * Add Seriallog disable after 600 seconds for Sonoff Dual and 4 Channel - * Add ButtonTopic2 - 4, SwitchTopic1 - 4 and SwitchRetain - * - * 3.2.2 20170113 - * Fix PowerOnState 2 functionality after re-applying power (#230) - * - * 3.2.1 20170113 - * Fix some failed command decoding (#228) - * Removed passwords from status messages (#216) - * - * 3.2.0 20170111 - * Add I2C BH1750 sensor (#222) - * Sensor rewrite preparing for online selection - * - * 3.1.16 20170109 - * Fix Domoticz possible error condition - * Remove Wifi password from connection message (#216) - * Add Configure Other menu item to web page (#209) - * Add command FriendlyName, field Friendly Name and define FRIENDLY_NAME to be used by Alexa - * eliminating current use of MQTT_CLIENT_ID (#209) - * Add friendlyname to webpage replacing former hostname - * - * 3.1.15 20170108 - * Fix Domoticz send key regression with Toggle command - * - * 3.1.14 20170107 - * Add support for command TOGGLE (define MQTT_CMND_TOGGLE) when ButtonTopic is in use and not equal to Topic (#207) - * - * 3.1.13 20170107 - * Fix web console command input when SUB_PREFIX contains '/' (#152) - * Add command response to web command (#200) - * Add option to disable MQTT as define USE_MQTT in user_config.h (#200) - * - * 3.1.12 20170106 - * Add OTA retry to solve possible HTTP transient errors (#204) - * Fix MQTT host discovery - * - * 3.1.11 20170105 - * Add mDNS to advertise webserver as .local/ - * - * 3.1.10 20170105 - * Fix ButtonTopic when SUB_PREFIX = PUB_PREFIX - * Add workaround for possible MQTT queueing when SUB_PREFIX = PUB_PREFIX - * Add optional MQTT host discovery using define USE_DISCOVERY in user_config.h (#115) - * - * 3.1.9 20170104 - * Fix Power Blink start position (toggled) - * Change PulseTime increments: 1 .. 111 in 0.1 sec (max 11 seconds) and 112 .. 64900 in seconds (= 12 seconds until 18 hours) (#188) - * Add support for SUB_PREFIX = PUB_PREFIX (#190) - * - * 3.1.8 20170103 - * Add retain flag to LWT offline and only send "tele/sonoff/LWT Offline" (#179) - * Change retained LWT Online message to only send "tele/sonoff/LWT Online" - * - * 3.1.7 20161231 - * Add retained message LWT Online when sonoff makes MQTT connection (#179) - * - * 3.1.6 20161230 - * Add blinking using commands BlinkTime, BlinkCount and Power Blink|3|BlinkOff|4 (#165) - * - * 3.1.5 20161228 - * Fix serial space command exception (28) - * - * 3.1.4 20161227 - * Fix MQTT subscribe regression exception (3) (#162) - * Fix serial empty command exception (28) - * - * 3.1.3 20161225 - * Extent Domoticz configuration webpage with optional indices (#153) - * Fix multi relay legacy tele message from tele/sonoff/2/POWER to tele/sonoff/POWER2 - * Add support for iTead Motor Clockwise/Anticlockwise - * - * 3.1.2 20161224 - * Extent command PowerOnState with toggle at power on (option 2 is now option 3!) (#156) - * - * 3.1.1 20161223 - * Add support for Sonoff Touch and Sonoff 4CH (#40) - * Update DomoticzIdx and DomoticzKeyIdx with relay/key index (DomoticzIdx1/DomoticzKeyIdx1) - * Add command PowerOnState to control relay(s) at power on (#154) - * - * 3.1.0 20161221 - * Add Sonoff Pow measurement smoothing - * Fix serial command topic preamble error (#151) - * Fix 2.x to 3.x migration inconsistencies (#146) - * - * 3.0.9 20161218 - * Add Sonoff Pow voltage reading when relay is on but no load present (#123) - * - * 3.0.8 20161218 - * Add temperature conversion to Fahrenheit as option in user_config.h (TEMP_CONVERSION) (#145) - * - * 3.0.7 20161217 - * Add user_config_override.h to be used by user to override some defaults in user_config.h (#58) - * Fix Sonoff Pow low power (down to 4W) intermittent measurements (#123) - * - * 3.0.6 20161217 - * Fix MQTT_CLIENT_ID starting with % sign as in "%06X" (#142) - * Add auto power off after PulseTime * 0.1 Sec to relay 1 (#134) - * - * 3.0.5 20161215 - * Add more control over LED with command LedState options (#136, #143) - * LED_OFF (0), LED_POWER (1), LED_MQTTSUB (2), LED_POWER_MQTTSUB (3), LED_MQTTPUB (4), LED_POWER_MQTTPUB (5), LED_MQTT (6), LED_POWER_MQTT (7) - * Add option WIFI_RETRY (4) to command WifiConfig to allow connection retry to other AP without restart (#73) - * - * 3.0.4 20161211 - * Fix intermittent Domoticz update misses (#133) - * - * 3.0.3 20161210 - * Fix compiler warnings (#132) - * Remove redundant code - * Fix Domoticz pushbutton support - * - * 3.0.2 20161209 - * Add pushbutton to SwitchMode (#130) - * - * 3.0.1 20161209 - * Fix initial config - * - * 3.0.0 20161208 - * Migrate and clean-up flash layout - * Settings from version 2.x are saved but settings from version 3.x can not be used with version 2.x - * Change SEND_TELEMETRY_RSSI to SEND_TELEMETRY_WIFI and add AP and SSID to telemetry - * Split long JSON messages - * Fix inconsistent status messages - * Fix all status messages to return JSON if enabled - * Remove relay index in cmnd/sonoff//POWER now changed - * to cmnd/sonoff/POWER for single relay units - * and cmnd/sonoff/POWER for multi relay units like Sonoff dual - * Add retain option to Power/Light status controlled by command PowerRetain On|Off (#126) - * - * 2.1.2 20161204 - * Add support for second wifi AP (#73) - * Update command WifiConfig - * Fix possible WifiManager hang - * - * 2.1.1a 20161203 - * Fix scan for wifi networks if WeMo is enabled - * Fix syslog setting using web page - * - * 2.1.1 20161202 - * Add support for ElectroDragon second relay and button (only toggle with optional ButtonTopic) (#110) - * - * 2.1.0 20161202 - * Add optional EXPERIMENTAL TLS to MQTT (#49) - * Fix MQTT payload handling (#111) - * Optimzed WeMo code - * - * 2.0.21a 20161201 - * Fix WeMo PowerPlug emulation - * - * 2.0.21 20161130 - * Add Belkin WeMo PowerPlug emulation enabled with USE_WEMO_EMULATION in user_config.h (Heiko Krupp) (#105, #109) - * - * 2.0.20 20161130 - * Relax MQTTClient naming but only allows hexadecimal uppercase numbers (#107) - * Add I2C support with command I2CScan - * Add I2C sensor driver for HTU21 as alternate sensor using TH10/16 connectors (Heiko Krupp) (#105) - * Add I2C sensor driver for BMP085/BMP180/BMP280/BME280 as alternate sensor using TH10/16 connectors - * - * 2.0.19a 20161127 - * Add support for ButtonTopic and ButtonRetain to wall switch function - * Add pullup to SWITCH_PIN and command SwitchMode to syntax - * - * 2.0.18 20161126 - * Add SUB_PREFIX multi level support allowing 'cmnd' or 'cmnd/level2/level3' - * Add wall switch function to GPIO14 and command SwitchMode (Alex Scott) (#103) - * - * 2.0.17 20161123 - * Calibrate HLWPCAL from 12345 to 12530 - * Add alternative sensor driver DHT2 using Adafruit DHT library - * Add define MESSAGE_FORMAT to user_config.h - * Throttle console messages - * Shorten JSON messages - * Fix possible Panic - * Fix User mode webserver security - * - * 2.0.16 20161118 - * Add alternative sensor driver DS18x20 using OneWire library (#95) - * Change sensor MQTT message from tele/sonoff/TEMPERATURE to tele/sonoff/DHT/TEMPERATURE or - * tele/sonoff/DS18B20/TEMPERATURE or tele/sonoff/DS18x20/1/TEMPERATURE - * Add sensors to root webpage and auto refresh every 4 seconds (#92) - * Add optional JSON messageformat to all telemetry data - * Enforce minimum TelePeriod to be 10 seconds - * Fix Energy Yesterday reset after restart - * Add Energy Today restore after controlled restart - * - * 2.0.15 20161116 - * Change TODAY_POWER and PERIOD_POWER to TODAY_ENERGY and PERIOD_ENERGY - * Fix serial regression - * Fix syslog hangs when loghost is unavailable - * - * 2.0.14 20161115 - * Add HLW threshold delay - * Fix HLW intermittent current deviation - * Fix button functionality during wificonfig - * Add CRC check to DS18B20 sensor (#88) - * - * 2.0.13 20161113 - * Add additional upload error code descriptions - * Add PlatformIO support (#80) - * - * 2.0.12 20161113 - * Fix Serial and Web response regression when no MQTT connection available - * Fix Sonoff Dual power telemetric data for second relay - * Removed MQTT password from Information web page - * Hide MQTT password from Configure MQTT web page - * - * 2.0.11 20161111 - * Rewrite button and web toggle code - * Fix NTP sync - * Add HLW calibration commands HLWPCAL, HLWUCAL and HLWICAL (need define USE_POWERCALIBRATION) - * Fix power threshold tests - * - * 2.0.10 20161109 - * Add additional Domoticz define (#63) - * Add defines MQTT_STATUS_ON and MQTT_STATUS_OFF in user_config.h to select status On/Off string - * Fix status response differences (#65) - * Fix divide by zero exception (#70) - * Fix syslog loop exception - * - * 2.0.9 20161108 - * clarify MODULE in user_config.h - * Fix hlw false values - * - * 2.0.8 20161108 - * Add initial status after power on - * Seperate driver files - * Fix hlw code and calibrate Pow - * Move user config defines to user_config.h (#61) - * - * 2.0.7 20161030 - * Make Ticker mandatory - * Add Domoticz support (Increase MQTT_MAX_PACKET_SIZE to 400) (#54) - * Add command MessageFormat 0|1 to select either legacy or JSON output - * - * 2.0.6 20161024 - * Add Sonoff Pow power factor - * Initial support for up to four relays using iTEAD PSB (4Channel) - * - Currently only supports one button (All buttons behave the same) - * - Use command MODEL 4 to select four relay option - * (After first power on it will support 2 relays like Sonoff Dual) - * Fix ledstate - * Add command Status 9 to display Sonoff Pow thresholds - * Add commands PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow and CurrentHigh for use - * with Sonoff Pow thresholds - * - * 2.0.5 20161018 - * Add updates to user_config.h - moved SEND_TELEMETRY_DS18B20 and SEND_TELEMETRY_DHT to module area. - * As Sonoff TH10/16 does not have the logic installed for GPIO04 You'll have to select ONE of both - * Add Sonoff Pow support (experimental until Pow tested) - * Add command Status 8 to display Sonoff Pow energy values - * Add command MqttUnits On|Off to add units to values - * Change web main page header character size - * Change On/Off to ON/OFF status messages to satisfy openHAB - * Change TEMP to TEMPERATURE and HUM to HUMIDITY - * - * 2.0.4 20161009 - * Add MQTT_BUTTON_RETAIN, SAVE_DATA and SAVE_STATE defines to user_config.h (#35) - * Update ButtonRetain to remove retained message(s) from broker when turned off - * Add Retain for second relay on Sonoff Dual - * Provide power status messages with device topic index if requested - * - * 2.0.3 20161008 - * Update wifi initialization - * Add command BUTTONRETAIN for optional MQTT retain on button press (#35) - * Add command SAVESTATE to disable power state save. May be used with MQTT retain - * - * 2.0.2 20161006 - * Fix wifi issue 2186 - * - * 2.0.1 20161002 - * Fix button press - * - * 2.0.0 20161002 - * Update Sonoff TH10/16 sensor pins (My TH10 only has GPIO14 connected) - * Add full support for Sonoff dual - * - * 1.0.35 20160929 - * Add more lines to console - * Add timeout and disable MQTT on web upload - * Add command SAVEDATA to control parameter save (for flash wear afficionados) (#30) - * - * 1.0.34 20160926 - * Fix button press six and seven - * Add more information to webserver - * - * 1.0.33 20160915 - * Better WPS error message - * Separate webserver code from support.ino into webserver.ino - * Fix webserver User by removing unwanted restart option - * - * 1.0.32 20160913 - * Add Wifi Protected Setup (WPS) as third option for initial config - * Add command WIFICONFIG replacing deprecated command SMARTCONFIG - * Add option WIFICONFIG 3 to start WPSconfig - * Add option WIFICONFIG 0 to start saved Wifi config tool (WPSconfig, Smartconfig or Wifimanager) - * Change button behaviour - See Wiki - * - * 1.0.31 20160907 - * Fix DS18B20 misread if teleperiod = 2 - * Tuned sensor code - * Updated prefered ElectroDragon connection to Relay 1 and Button 1 - * Moved SONOFF and ELECTRO_DRAGON port config to user_config.h - * - * 1.0.30 20160902 - * Fix command TELEPERIOD 0 - * Add ESP- tag to UDP log message for easy rsyslogd filtering - * Add ElectroDragon (Relay 2 only) functionality. Select with #define MODULE ELECTRO_DRAGON - * Add ? as null message alternative - * Add DHT temperature and humidity telemetry support. Enable with #define SEND_TELEMETRY_DHT - * Add DS18B20 temperature telemetry support. Enable with #define SEND_TELEMETRY_DS18B20 - * Restrict HOSTNAME, MQTTCLIENT, TOPIC and BUTTONTOPIC in topic mode only - * - * 1.0.29 20160831 - * Allow UPGRADE, OTAURL, RESTART, RESET, MQTTHOST, MQTTPORT, MQTTUSER, MQTTPASSWORD and WEBSERVER also in group mode - * - * 1.0.28 20160831 - * Add webserver state to status 5 - * Add optional PUB_PREFIX2 (tele) for telemetry usage - * Add command TELEPERIOD - * Fix syntax message - * Change memory status display - * - * 1.0.27 20160831 - * Add sketch flash size - * Add console to webserver - * Add command weblog - * Change WifiManager web pages to minimal - * Change display default hostname and MQTT client id in webserver - * Change HTTP command interface to http://sonoff-1234/cm?cmnd=light 2 - * Change HEARTBEAT to UPTIME - * - * 1.0.26 20160829 - * Add define USE_WEBSERVER to disable web server code in source - * Add file upload as alternative for ota upload to webserver - * Add information to webserver - * Add command hostname - * Add command logport - * Change HTTP command interface to http://sonoff-1234/cmd?cmnd=light 2 - * Change button behaviour with regards to Smartconfig and OTA upload. See README.md - * Enforce default hostname to either "%s-%04d" or user defined without any % - * Enforce default mqtt client id to either "DVES_%06X" or user defined without any % - * - * 1.0.25 20160822 - * Remove config system halts to keep ota available - * - * 1.0.24 20160821 - * Add test for MQTT_SUBTOPIC - * Change log range to LOG_LEVEL_ALL - * Change MQTT introduction messages - * Moved MQTT_MAX_PACKET_SIZE warning message to introduction messages - * - * 1.0.23 20160821 - * Add option USE_SPIFFS to move config from flash to spiffs - * Add webserver with options 0 (off), 1 (user) and 2 (admin) - * Add HTTP command interface (http://sonoff-1234/c?cmnd=light 2) - * Add wifimanager countdown counter - * Add command line webpage - * Add relay control to wifimanager - * Add restart option 99 to force restart - * Fix wifi hostname - * Fix NETBIOS hostname problem by reducing default hostname length - * Fix possible exception if WIFI_HOSTNAME is changed - * Fix upgrade messages - * Reduce memory use by redesigning config routines - * Split syntax message - * Rename define SERIAL_IO to USE_SERIAL - * - * 1.0.22 20160814 - * Add all MQTT parameters for configuration - * Add wifimanager to configure Wifi and MQTT via web server - * Change NTP time handling - * Fix Smartconfig parameter buffer overflow - * Fix PlatformIO warnings - * - * 1.0.21 20160808 - * Remove semaphore as subscription flooding (more than 15 subscriptions per second) is managed by SDK (LmacRxBlk:1) - * Add optional RTC interrupt (define USE_TICKER) to keep RTC synced during subscription flooding - * Remove heartbeatflag - * - * 1.0.20 20160805 - * Add semaphore to handle out of memory when too many subscriptions requested - * Use Daylight Saving (DST) parameters from user_config.h when timezone = 99 - * Add status 7 option displaying RTC information - * Add ledstate to status 0 - * - * 1.0.19 20160803 - * Fix possible MQTT_CLIENT_ID induced Exception(28) - * - * 1.0.18 20160803 - * Moved Cfg_Default - * Fix negative data handling - * Remove MQTT information from status 1 and add labels to status 1 - * Add mac address to status 5 - * Add MQTT ClientId, UserId and Password to status 6 - * - * 1.0.17 20160731 - * Better variable range checking - * Change ambiguous connection messages - * Add timestamp to serial message - * - * 1.0.16 20160729 - * Moved wifi, rtc, syslog and config to support.ino - * Fixed button action when buttontopic is used. Introduced with 1.0.15 - * Better buffer overflow checks (strlcpy) - * - * 1.0.15 20160728 - * Removed pubsubclient config changes from sonoff.ino as it doesn't work - * reapply MQTT_MAX_PACKET_SIZE 256 and MQTT_KEEPALIVE 120 to PubSubClient.h - * Add status 0 option displaying all status messages - * Change MQTT_MAX_PACKET_SIZE from 1024 to 256 - * Add buffer overflow checks (snprintf and strncpy) - * Implemented common string sizes - * - * 1.0.14 20160722 - * Seperate user config from sonoff.ino to user_config.h (pucebaboon) - * Change defaults from sidnas2 to domus1 - * Add MQTT status message as status 6 (pucebaboon) - * Add status type to message (pucebaboon) - * Add pubsubclient config changes to sonoff.ino (pucebaboon) - * - * 1.0.13 20160702 - * Add Ledstate 1 option to show power state on led - * - * 1.0.12 20160529 - * Allow disable of button topic using "0" - * - * 1.0.11 20160524 - * Provide button response if MQTT connection lost - * - * 1.0.10 20160520 - * Add optional button topic to assist external MQTT clients - * Change version notation - * Reset default values - * - * 1.0.9 20160503 - * Add more blinks - * Add reset 2 option erasing flash - * Add status 5 option displaying network info - * Add syslog check for Wifi connection - * Resize MqttPublish log array - * Change Wifi smartconfig active from 100 to 60 seconds - * Update Wifi initialization - * - * 1.0.8 20160430 - * Remove use of Wifi config data from SDK - * Add status 3 (syslog info) and status 4 (flash info) - * Add restart option to button (5 quick presses) - * - * 1.0.7 20160420 - * Add UDP syslog support - * Change HOST command to MQTTHOST command - * Add commands SYSLOG, SERIALLOG and LOGHOST - * Change hostname to lower case to distinguise between open-sdk version - * Add support for ESP-12F used in my modified wkaku power socket switch - * Fix timezone command - * Add RTC month names for future use - * Modify button code - * Remove initialization errors by better use of MQTT loop - * - * 1.0.6 20160406 - * Removed Wifi AP mode (#1) - * Add test for Arduino IDE version >= 1.6.8 - * Fix RTC time sync code - * - * 1.0.5 20160310 - * Initial public release - * Show debug info by selecting option from IDE Tools Debug port: Serial -\*********************************************************************************************/