From 7151c4016d63456c8f0c7cab3607cb0e66abbe22 Mon Sep 17 00:00:00 2001 From: Theo Arends <11044339+arendst@users.noreply.github.com> Date: Wed, 23 Oct 2019 15:20:43 +0200 Subject: [PATCH] Release 6.7 --- RELEASENOTES.md | 122 +++++++++++++++++++++++++++++++++++++++- sonoff/_changelog.ino | 3 + sonoff/sonoff_version.h | 2 +- 3 files changed, 124 insertions(+), 3 deletions(-) diff --git a/RELEASENOTES.md b/RELEASENOTES.md index 89efea9d5..7609f8860 100644 --- a/RELEASENOTES.md +++ b/RELEASENOTES.md @@ -99,6 +99,8 @@ Module | Description 71 Sonoff iFan03 | Sonoff iFan03 Wifi Smart Ceiling Fan with Light 72 EXS Dimmer | EXS Wifi Dimmer v4 +Over 500 additional devices are supported using [templates](TEMPLATES.md). + ## Provided Binary Downloads The following binary downloads have been compiled with ESP8266/Arduino library core version **pre-2.6.0**. @@ -257,5 +259,121 @@ The following binary downloads have been compiled with ESP8266/Arduino library c | USE_DISPLAY_RA8876 | - | - | - | - | - | - | - | ## Changelog -Version 6.7.0 20191101 - * TBS +Version 6.7.0 20191025 + * Remove support for WPS and SmartConfig in favour of Web server (!) based WifiManager (#6680) + * Remove binary sonoff-classic (#6680) + * Remove command SetOption2 + * Remove default DS18B20 driver and only support define DS18x20 (#6647) + * Remove support for define USE_DS18x20_LEGACY and legacy DS18x20 driver (#6486) + * Replace xsns_23_sdm120 with xnrg_08_sdm120 + * Replace xsns_25_sdm630 with xnrg_10_sdm630 + * Replace xsns_49_solaxX1 with xnrg_12_solaxX1 (#6677) + * Change Sonoff L1 support by adding define USE_SONOFF_L1 + * Change light drivers internals to ease management + * Change command PulseTime JSON message format and allow display of all pulsetimer information (#6519) + * Change command SetOption43 to make it more general. Now supports PS_16_DZ driver too (#6544) + * Change command handling by moving buffers up in chain solving MQTTlog support (#6529) + * Change commands Var and Mem to show all parameters when no index is given (#6107) + * Change detection of non-MQTT commands by allowing non-space characters as delimiter (#6540) + * Change rename "Data" to "Hash" and limit to 32 bits when receiving UNKNOWN IR protocol (see DECODE_HASH from IRremoteESP8266) + * Change JSON output format for commands Adc, Adcs, Modules, Gpio and Gpios from list to dictionary (#6407) + * Change energy sensors for three phase/channel support + * Change Settings crc calculation allowing short term backward compatibility + * Change Improve reliability of TasmotaSerial at 115200 bauds and reduce IRAM usage for Stage/pre-2.6 + * Change Tuya support by Shantur Rathore removing commands SetOption34, 41, 44, 45, 46 and 65 (#6353) + * Change theoretical baudrate range to 300..19660500 bps in 300 increments (#6294) + * Change Settings area to 4k for future use + * Change some table locations from RAM to Flash + * Change filename of configuration backup from using FriendlyName1 to Hostname solving diacritic issues (#2422) + * Change Store AWS IoT Private Key and Certificate in SPI Flash avoiding device-specific compilations + * Change defines USE_TX20_WIND_SENSOR and USE_RC_SWITCH in my_user_config.h to disable to lower iram usage enabling latest core compilation (#6060, #6062) + * Fix handling of ligth channels when pwm_multichannel (Option68) is enabled + * Fix better handling of PWM White Temperature mode for Module 48 (#6534) + * Fix TasmotaSerial: move serial send to IRAM for high speed baud rates + * Fix Domoticz battery level set to 100 if define USE_ADC_VCC is not used (#6033) + * Fix Force Elliptic Curve for Letsencrypt TLS #6042 + * Fix WeMo emulation for 1G echo and 2G echo dot (#6086) + * Fix Xiaomi Philips brightness (#6091) + * Add support for EX-Store WiFi Dimmer V4 (#5856) + * Add support for Arduino serial connection (EXPERIMENTAL) + * Add support for Zigbee devices Xiaomi lumi.weather air quality sensor, Osram mini-switch + * Add support for Zigbee device cc2530 initialization and basic ZCL decoding + * Add support for PMS3003 dust particle sensor + * Add support for Chint DDSU666 Modbus energy meter by Pablo Zerón + * Add support for SM2135 as used in Action LSC Smart Led E14 (#6495) + * Add support for Shelly 2.5 dual energy (#6160) + * Add support for shutters by Stefan Bode (#288) + * Add support for PCF8574 I2C I/O Expander (currently output only) by Stefan Bode + * Add support for up to three PZEM-014/-016 on one serial modbus connection with addresses 1 (default), 2 and 3 (#2315) + * Add support for up to three PZEM-004T on one serial connection with addresses 192.168.1.1 (default), 2 and 3 (#2315) + * Add support for up to three PZEM-003/-017 on one serial modbus connection with addresses 1 (default), 2 and 3 (#2315) + * Add support for up to 4 INA226 Voltage and Current sensors by Steve Rogers (#6342) + * Add support for A4988 stepper-motor-driver-circuit by Tim Leuschner (#6370) + * Add support for Hiking DDS238-2 Modbus energy meter by Matteo Campanella (#6384) + * Add support for HM17 bluetooth LE passive scan of ibeacon devices by Gerhard Mutz + * Add support for Solax X1 inverter by Pablo Zerón + * Add support for PAJ7620 gesture sensor by Christian Baars + * Add support for MAX31865 Thermocouple sensor by Alberto Lopez Siemens + * Add support for RDM6300 125kHz RFID Reader by Gerhard Mutz + * Add support for CHIRP soil moisture sensor by Christian Baars + * Add support for Sonoff iFan03 as module 71 (#5988) + * Add support for a buzzer + * Add support for IRSend long press ('repeat' feature from IRRemoteESP8266) (#6074) + * Add support for IRHVAC Midea/Komeco protocol (#3227) + * Add support for more IRSend protocols enabled in my_user_config.h + * Add support for IRSend Pioneer protocol (#6100) + * Add support for up to 4 INA219 sensors (#6046) + * Add support for I2C display driver SH1106 oled by Gerhard Mutz + * Add support for SPI display drivers epaper 4.2 inch, ILI9488 TFT, SSD1351 Color oled and RA8876 TFT by Gerhard Mutz + * Add command Buzzer with optional parameters ,, enabled when a buzzer is configured (#5988) + * Add command DimmerRange in Light module to support 2 byte dimming ranges from Tuya + * Add command DisplayHeight to set pixel height on supported devices + * Add command DisplayWidth to set pixel width on supported devices + * Add command EnergyReset4 x,x to initialize total usage for two tarrifs + * Add command EnergyReset5 x,x to initialize total export (or production) for two tarrifs + * Add command Gpio 255/All to show physical GPIO configuration of all non-flash pins (#6407) + * Add command Gpios 255/All to show all available GPIO components (#6407) + * Add command ModuleAddress 1/2/3 to set Pzem module address when a single module is connected (#2315) + * Add command MqttLog for support of MQTT logging (#6498) + * Add command Power0 0/1/2/Off/On/Toggle to control all power outputs at once (#6340) + * Add command PowerDelta 101..32000 for absolute power delta where 101 = 101-100 = 1W, 202 = 202-100 = 102W (#5901) + * Add command Reset 99 to reset bootcount to zero (#684, #6351) + * Add command Sensor29 pin,0/1/2 for OFF/ON/TOGGLE + * Add command Sensor34 8,0 and Sensor34 8,1 to disable/enable JSON message on weight change over 4 gram + * Add command SetOption34 0..255 to set backlog delay. Default value is 200 (mSeconds) (#6562) + * Add command SetOption42 0..255 to set overtemperature (Celsius only) threshold resulting in power off all on energy monitoring devices. Default setting is 90 (#6036) + * Add command SetOption65 0/1 to disable (1) fast power cycle detection fixing unwanted brownout trigger + * Add command SetOption66 0/1 to enable or disable Tuya dimmer range 255 slider control + * Add command SetOption67 0/1 to disable or enable a buzzer as used in iFan03 + * Add command SetOption68 to enable multi-channel PWM instead of a single light (#6134) + * Add command SetOption71 0/1 to switch between different Modbus Active Energy registers on DDS238-2 energy meters (#6531) + * Add command SetOption72 0/1 to switch between software (0) or hardware (1) energy total counter (#6561) + * Add command Time to disable NTP and set UTC time as Epoch value if above 1451602800 (=20160101). Time 0 re-enables NTP (#5279) + * Add command Time 1/2/3 to select JSON time format ISO + Epoch, ISO or Epoch + * Add command Tariff to default to 0 (=disabled) and allowing to set both Standard Time (ST) and Daylight Savings Time (DST) start hour + ex. Tariff1 22,23 = Tariff1 (Off-Peak) ST,DST Tariff2 (Standard) 6,7 = Tariff2 ST,DST Tariff9 0/1 = Weekend toggle (1 = Off-Peak during weekend) + * Add command WebSensor 0/1 to control display of sensor data in web GUI (#6085) + * Add command ZigbeeRead (#6095) + * Add define USE_DEEPSLEEP and command DeepSleepTime 0 or 10..86400 (seconds) to enter deepsleep mode (#6638) + * Add define USE_ENERGY_MARGIN_DETECTION to disable Energy Margin and Power Limit detection + * Add define USE_ENERGY_POWER_LIMIT to disable Energy Power Limit detection while Energy Margin detection is active + * Add define USE_SONOFF_RF to enable/disable Sonoff Rf support (#6648) + * Add define USE_WS2812_HARDWARE to select hardware type WS2812, WS2812X, WS2813, SK6812, LC8812 or APA106 (DMA mode only) + * Add incremental beeps to Ifan03 remote control fan speed buttons (#6636) + * Add rule support after every command execution like Fanspeed#Data=2 (#6636) + * Add WebUI for multiple, independent PWM channels + * Add JSON array index support to rules evaluation allowing trigger on ENERGY#POWER[2]>0.60 from JSON ..,"Power":[0.00,0.68],.. (#6160) + * Add Full support of all protocols in IRremoteESP8266, to be used on dedicated-IR Tasmota version. Warning: +81k Flash when compiling with USE_IR_REMOTE_FULL + * Add 'sonoff-ir' pre-packaged IR-dedicated firmware and 'sonoff-ircustom' to customize firmware with IR Full protocol support + * Add driver USE_SDM120_2 with Domoticz P1 Smart Meter functionality as future replacement for USE_SDM120 - Pls test and report + * Add Tuya Energy monitoring by Shantur Rathore + * Add Domoticz P1 Smart Meter support using energy sensors handled by xdrv_03_energy.ino based on an idea by pablozg + * Add debug compile features using defines DEBUG_TASMOTA_CORE, DEBUG_TASMOTA_DRIVER and DEBUG_TASMOTA_SENSOR. + See DEBUG_CORE_LOG example in sonoff.ino and DEBUG_DRIVER_LOG example in xdrv_09_timers.ino + * Add option 0 to Width1 (Marker), Width2 (Second), Width3 (Minute) and Width4 (Hour) disabling display (#6152) + * Add MqttCount metric to STATE (#6155) + * Add allow repeat/longpress for IRSend raw, introduced IRSend option (#6074) + * Add Oled reset GPIO option "OLED reset" + * Add blend RGB leds with White leds for better whites (#5895, #5704) + * Add AZ7798 automatic setting of clock display (#6034) + * Add Epoch and UptimeSec to JSON messages (#6068) diff --git a/sonoff/_changelog.ino b/sonoff/_changelog.ino index 1c37b3664..b964b449d 100644 --- a/sonoff/_changelog.ino +++ b/sonoff/_changelog.ino @@ -1,4 +1,7 @@ /*********************************************************************************************\ + * 6.7.0 20191025 + * Release + * * 6.6.0.21 20191022 * Remove support for WPS and SmartConfig in favour of Web server (!) based WifiManager (#6680) * Remove binary sonoff-classic (#6680) diff --git a/sonoff/sonoff_version.h b/sonoff/sonoff_version.h index 22e12ed7b..1731d80a5 100644 --- a/sonoff/sonoff_version.h +++ b/sonoff/sonoff_version.h @@ -20,6 +20,6 @@ #ifndef _SONOFF_VERSION_H_ #define _SONOFF_VERSION_H_ -const uint32_t VERSION = 0x06060015; +const uint32_t VERSION = 0x06070000; #endif // _SONOFF_VERSION_H_