diff --git a/tasmota/my_user_config.h b/tasmota/my_user_config.h
index e2289532c..94e528a86 100644
--- a/tasmota/my_user_config.h
+++ b/tasmota/my_user_config.h
@@ -983,9 +983,9 @@
 
 #define SET_ESP32_STACK_SIZE  (8 * 1024)         // Set the stack size for Tasmota. The default value is 8192 for Arduino, some builds might need to increase it
 
-//#define USE_SONOFF_SPM                           // Add support for ESP32 based Sonoff Smart Stackable Power Meter(+6k3 code)
+//#define USE_SONOFF_SPM                           // Add support for ESP32 based Sonoff Smart Stackable Power Meter (+11k code)
 
-//#define USE_ETHERNET                             // Add support for ethernet (Currently fixed for Olimex ESP32-PoE)
+//#define USE_ETHERNET                             // Add support for ethernet (+20k code)
 //  #define USE_WT32_ETH01                         // Add support for Wireless-Tag WT32-ETH01
 //  #define ETH_TYPE          0                    // [EthType] 0 = ETH_PHY_LAN8720, 1 = ETH_PHY_TLK110/ETH_PHY_IP101, 2 = ETH_PHY_RTL8201, 3 = ETH_PHY_DP83848, 4 = ETH_PHY_DM9051, 5 = ETH_PHY_KSZ8081
 //  #define ETH_ADDRESS       1                    // [EthAddress] 0 = PHY0 .. 31 = PHY31
diff --git a/tasmota/tasmota_configurations_ESP32.h b/tasmota/tasmota_configurations_ESP32.h
index b1d0de26d..8a533e0b4 100644
--- a/tasmota/tasmota_configurations_ESP32.h
+++ b/tasmota/tasmota_configurations_ESP32.h
@@ -377,7 +377,7 @@
 //#define USE_EZOPMP                             // [I2cDriver55] Enable support for EZO's PMP sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code)
 //#define USE_SEESAW_SOIL                        // [I2cDriver56] Enable Capacitice Soil Moisture & Temperature Sensor (I2C addresses 0x36 - 0x39) (+1k3 code)
 
-//#define USE_SPI                                // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC)
+#define USE_SPI                                // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC)
 //#define USE_RC522                              // Add support for MFRC522 13.56Mhz Rfid reader (+6k code)
 
 #define USE_MHZ19                                // Add support for MH-Z19 CO2 sensor (+2k code)
@@ -434,6 +434,7 @@
 //#define USE_LE01MR                               // Add support for F&F LE-01MR modbus energy meter (+2k code)
 //#define USE_TELEINFO                             // Add support for French Energy Provider metering telemetry (+5k2 code, +168 RAM + SmartMeter LinkedList Values RAM)
 //#define USE_WE517                                // Add support for Orno WE517-Modbus energy monitor (+1k code)
+#define USE_SONOFF_SPM                           // Add support for ESP32 based Sonoff Smart Stackable Power Meter (+11k code)
 
 #define USE_DHT                                  // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor
 #define USE_MAX31855                             // Add support for MAX31855 K-Type thermocouple sensor using softSPI
@@ -456,6 +457,8 @@
 //#define USE_A4988_STEPPER                        // Add support for A4988/DRV8825 stepper-motor-driver-circuit (+10k5 code)
 //#define USE_THERMOSTAT                           // Add support for Thermostat
 
+#define USE_ETHERNET                             // Add support for ethernet (+20k code)
+
 #ifndef USE_KNX
 #define USE_KNX                                  // Enable KNX IP Protocol Support (+23k code, +3k3 mem)
 #endif