From f3123a276105f4dba1648d4909f7d9382485bbb4 Mon Sep 17 00:00:00 2001
From: Jason2866 <24528715+Jason2866@users.noreply.github.com>
Date: Sat, 5 Sep 2020 18:05:43 +0200
Subject: [PATCH] Delete core_esp8266_waveform.h

---
 tasmota/core_esp8266_waveform.h | 93 ---------------------------------
 1 file changed, 93 deletions(-)
 delete mode 100644 tasmota/core_esp8266_waveform.h

diff --git a/tasmota/core_esp8266_waveform.h b/tasmota/core_esp8266_waveform.h
deleted file mode 100644
index ff5a0f56f..000000000
--- a/tasmota/core_esp8266_waveform.h
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
-  esp8266_waveform - General purpose waveform generation and control,
-                     supporting outputs on all pins in parallel.
-
-  Copyright (c) 2018 Earle F. Philhower, III.  All rights reserved.
-  Copyright (c) 2020 Dirk O. Kaar.
-
-  The core idea is to have a programmable waveform generator with a unique
-  high and low period (defined in microseconds or CPU clock cycles).  TIMER1 is
-  set to 1-shot mode and is always loaded with the time until the next edge
-  of any live waveforms.
-
-  Up to one waveform generator per pin supported.
-
-  Each waveform generator is synchronized to the ESP clock cycle counter, not the
-  timer.  This allows for removing interrupt jitter and delay as the counter
-  always increments once per 80MHz clock.  Changes to a waveform are
-  contiguous and only take effect on the next waveform transition,
-  allowing for smooth transitions.
-
-  This replaces older tone(), analogWrite(), and the Servo classes.
-
-  Everywhere in the code where "ccy" or "ccys" is used, it means ESP.getCycleCount()
-  clock cycle count, or an interval measured in CPU clock cycles, but not TIMER1
-  cycles (which may be 2 CPU clock cycles @ 160MHz).
-
-  This library is free software; you can redistribute it and/or
-  modify it under the terms of the GNU Lesser General Public
-  License as published by the Free Software Foundation; either
-  version 2.1 of the License, or (at your option) any later version.
-
-  This library is distributed in the hope that it will be useful,
-  but WITHOUT ANY WARRANTY; without even the implied warranty of
-  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
-  Lesser General Public License for more details.
-
-  You should have received a copy of the GNU Lesser General Public
-  License along with this library; if not, write to the Free Software
-  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
-*/
-
-#ifdef ESP8266
-
-#include <Arduino.h>
-
-#ifndef __ESP8266_WAVEFORM_H
-#define __ESP8266_WAVEFORM_H
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-// Start or change a waveform of the specified high and low times on specific pin.
-// If runtimeUS > 0 then automatically stop it after that many usecs, relative to the next
-// full period.
-// If waveform is not yet started on pin, and on pin == alignPhase a waveform is running,
-// the new waveform is started at phaseOffsetUS phase offset, in microseconds, to that.
-// Setting autoPwm to true allows the wave generator to maintain PWM duty to idle cycle ratio
-// under load, for applications where frequency or duty cycle must not change, leave false.
-// Returns true or false on success or failure.
-int startWaveform(uint8_t pin, uint32_t timeHighUS, uint32_t timeLowUS,
-  uint32_t runTimeUS = 0, int8_t alignPhase = -1, uint32_t phaseOffsetUS = 0, bool autoPwm = false);
-// Start or change a waveform of the specified high and low CPU clock cycles on specific pin.
-// If runtimeCycles > 0 then automatically stop it after that many CPU clock cycles, relative to the next
-// full period.
-// If waveform is not yet started on pin, and on pin == alignPhase a waveform is running,
-// the new waveform is started at phaseOffsetCcys phase offset, in CPU clock cycles, to that.
-// Setting autoPwm to true allows the wave generator to maintain PWM duty to idle cycle ratio
-// under load, for applications where frequency or duty cycle must not change, leave false.
-// Returns true or false on success or failure.
-int startWaveformClockCycles(uint8_t pin, uint32_t timeHighCcys, uint32_t timeLowCcys,
-  uint32_t runTimeCcys = 0, int8_t alignPhase = -1, uint32_t phaseOffsetCcys = 0, bool autoPwm = false);
-// Stop a waveform, if any, on the specified pin.
-// Returns true or false on success or failure.
-int stopWaveform(uint8_t pin);
-
-// Add a callback function to be called on *EVERY* timer1 trigger.  The
-// callback returns the number of microseconds until the next desired call.
-// However, since it is called every timer1 interrupt, it may be called
-// again before this period.  It should therefore use the ESP Cycle Counter
-// to determine whether or not to perform an operation.
-// Pass in NULL to disable the callback and, if no other waveforms being
-// generated, stop the timer as well.
-// Make sure the CB function has the ICACHE_RAM_ATTR decorator.
-void setTimer1Callback(uint32_t (*fn)());
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif
-
-#endif  // ESP8266