# Changelog All notable changes to this project will be documented in this file. ## [Unreleased] - Development ## [9.0.0.3] ### Added - TLS in binary tasmota-zbbridge (#9635) - Support for EZO O2 sensors by Christopher Tremblay (#9619) - Support for EZO PRS sensors by Christopher Tremblay (#9659) - Support for EZO FLO sensors by Christopher Tremblay (#9697) - Support for EZO DO sensors by Christopher Tremblay (#9707) - Zigbee reduce battery drain (#9642) - Zigbee command ``ZbMap`` to describe Zigbee topology (#9651) - Zigbee command ``ZbOccupancy`` to configure the time-out for PIR - Command ``Gpios 255`` to show all possible GPIO configurations - Command ``SwitchText`` to change JSON switch names by barbudor (#9691) - HM10 Beacon support and refactoring by Christian Baars (#9702) ### Changed - PlatformIO library structure redesigned for compilation speed by Jason2866 - Zigbee flash storage refactor adding commands ``ZbProbe``, ``ZbStatus2`` and ``ZbRestore`` (#9641) - Default otaurl in my_user_config.h to http://ota.tasmota.com/tasmota/release/tasmota.bin.gz ### Fixed - Rule Break not working as expected when ONCE is enabled (#9245) - Rule expressions using mems corrupts character pool (#9301) - Button press rules regression introduced by #9589 (#9700) ## [9.0.0.2] - 20201025 ### Added - Support for Vietnamese language translations by Tâm.NT - Support for timers in case of no-sunset permanent day by cybermaus (#9543) - Command ``NoDelay`` for immediate backlog command execution by Erik Montnemery (#9544) - Command ``SwitchMode 15`` sending only MQTT message on switch change (#9593) - Command ``ShutterChange`` to increment change position (#9594) - Command ``SetOption113 1`` to set dimmer low on rotary dial after power off - Support for EZO Ph and ORP sensors by Christopher Tremblay (#9567) - Support for EZO RTD sensors by Christopher Tremblay (#9585) - Support for EZO HUM sensors by Christopher Tremblay (#9599) - Support for EZO EC sensors by Christopher Tremblay (#9613) - Support for EZO CO2 sensors by Christopher Tremblay (#9619) - On ZigbeeBridge support for glowing led when permit join is active (#9581) - Support for PWM Dimmer multi-press and ledmask (#9584) - Make button press rules override PWM Dimmer functions (#9589) - Support for fixed output Hi or Lo GPIO selection - ESP32 support for Wireless-Tag WT32-ETH01 (#9496) - ESP32 MI32 Beacon support, RSSI at TELEPERIOD, refactoring by Christian Baars (#9609) ### Changed - Command ``Gpio17`` replaces command ``Adc`` - Command ``Gpios`` replaces command ``Adcs`` - Management of serial baudrate (#9554) - TLS fingerprint ``#define MQTT_FINGERPRINT`` from string to hexnumbers (#9570) - Rotary driver adjusted accordingly if Mi Desk Lamp module is selected (#9399) - Tasmota Arduino Core v2.7.4.5 allowing webpassword over 47 characters (#9687) - Webserver code optimizations (#9580, #9590) ### Fixed - Convert AdcParam parameters from versions before v9.0.0.2 - Telegram message decoding error regression from v8.5.0.1 - Correct Energy period display shortly after midnight by gominoa (#9536) - Rule handling of Var or Mem using text regression from v8.5.0.1 (#9540) - TuyaMcu energy display regression from v8.5.0.1 (#9547) - Tuyamcu dimmers MQTT topic (#9606) - MQTT data corruption on ``MQTTLog 4`` (#9571) - Scripter memory alignment (#9608) - Zigbee battery percentage (#9607) - HassAnyKey anomaly (#9601) - ESP32 Webcam broken regression from #9590 ## [9.0.0.1] - 20201010 ### Added - Optional support for Mitsubishi Electric HVAC by David Gwynne (#9237) - Optional support for Orno WE517-Modbus energy meter by Maxime Vincent (#9353) - SDM630 three phase ImportActive Energy display when ``#define SDM630_IMPORT`` is enabled by Janusz Kostorz (#9124) - Optional support for inverted NeoPixelBus data line by enabling ``#define USE_WS2812_INVERTED`` (#8988) - PWM dimmer color/trigger on tap, SO88 led, DGR WITH_LOCAL flag by Paul Diem (#9474) - Support for stateful ACs using ``StateMode`` in tasmota-ir.bin by Arik Yavilevich (#9472) - Zigbee command ``ZbData`` for better support of device specific data - Support for analog buttons indexed within standard button range ### Changed - Redesigning ESP8266 GPIO internal representation in line with ESP32 changing ``Template`` layout too - New IR Raw compact format (#9444) - MAX31865 driver to support up to 6 thermocouples selected by ``MX31865 CS`` instead of ``SSPI CS`` (#9103) - A4988 optional microstep pin selection - Pulsetime to allow use for all relays with 8 interleaved so ``Pulsetime1`` is valid for Relay1, Relay9, Relay17 etc. (#9279) - ``Status`` command output for disabled status types - IRremoteESP8266 library from v2.7.10 to v2.7.11 - NeoPixelBus library from v2.5.0.09 to v2.6.0 ### Fixed - Template conversion when GPIO17 is 0 - Template using ``#define USER_TEMPLATE`` (#9506) - Ledlink blink when no network connected regression from v8.3.1.4 (#9292) - Exception 28 due to device group buffer overflow (#9459) - Shutter timing problem due to buffer overflow in calibration matrix (#9458) - Light wakeup exception 0 (divide by zero) when ``WakeupDuration`` is not initialised (#9466) - ADC initalization sequence (#9473) - Thermostat sensor status corruption regression from v8.5.0.1 (#9449) ### Removed - Support for direct upgrade from Tasmota versions before v7.0 - Auto config update for all Friendlynames and Switchtopic from Tasmota versions before v8.0 ## [Released] ## [8.5.1] - 20201002 - Release Hannah ## [8.5.0.1] - 20200907 ### Added - Command ``SetOption110 1`` to disable Zigbee auto-config when pairing new devices - Command ``SetOption111 1`` to enable frequency output for buzzer GPIO (#8994) - Command ``SetOption112 1`` to enable friendly name in zigbee topic (use with SetOption89) - ``#define USE_MQTT_AWS_IOT_LIGHT`` for password based AWS IoT authentication - ``#define MQTT_LWT_OFFLINE`` and ``#define MQTT_LWT_ONLINE`` to user_config.h (#9395) - New shutter modes (#9244) - Zigbee auto-config when pairing - Support for MLX90640 IR array temperature sensor by Christian Baars - Support for VL53L1X time of flight sensor by Johann Obermeier ### Changed - Replace ArduinoJson with JSMN for JSON parsing - ``WakeUp`` uses 256 steps instead of 100 (#9241) - Major redesign of TuyaMcu adding shutter, light and multiple dimmer support by Federico Leoni (#9330) ### Fixed - Energy total counters (#9263, #9266) - Crash in ``ZbRestore`` - Reset BMP sensors when executing command ``SaveData`` and define USE_DEEPSLEEP enabled (#9300) - ``status 0`` message when using define USE_MQTT_TLS due to small log buffer (#9305) - ``status 13`` exception 9 when more than one shutter is configured - ``status 13`` json message - Shelly 2.5 higher temperature regression from 8.2.0.1 (#7991) ## [8.5.0] - 20200907 - Release Hannah ## [8.4.0.3] - 20200823 ### Added - Command ``PowerDelta1`` to ``PowerDelta3`` to trigger on up to three phases (#9134) - Zigbee web ui widget for Lights - ``SetOption109 1`` to force gen1 Alexa mode, for Echo Dot 2nd gen devices only - Zigbee web ui for power metering plugs - Experimental support for ESP32 TTGO Watch and I2S Audio by Gerhard Mutz ### Changed - References from http://thehackbox.org/tasmota/ to http://ota.tasmota.com/tasmota/ ## [8.4.0.2] - 20200813 ### Added - Command ``SetOption103 0/1`` to set TLS mode when TLS is selected - Command ``SetOption104 1`` to disable all MQTT retained messages - Command ``SetOption106 1`` to create a virtual White ColorTemp for RGBW lights - Command ``SetOption107 0/1`` to select virtual White as (0) Warm or (1) Cold - Command ``SetOption108 0/1`` to enable Teleinfo telemetry into Tasmota Energy MQTT (0) or Teleinfo only (1) - Add better config corruption recovery (#9046) - Virtual CT for 4 channels lights, emulating a 5th channel - Support for DYP ME007 ultrasonic distance sensor by Janusz Kostorz (#9113) - Zigbee web gui widget for Temp/Humidity/Pressure sensors - Zigbee battery icon ### Changed - White blend mode moved to using ``SetOption 105`` instead of ``RGBWWTable`` ### Fixed - Display power control (#9114) ### Removed - Support for direct upgrade from versions before 6.6.0.11 to versions after 8.4.0.1 ## [8.4.0.1] - 20200730 ### Added - Zigbee better support for IKEA Motion Sensor - ESP32 Analog input support for GPIO32 to GPIO39 - Zigbee options to ``ZbSend`` ``Config`` and ``ReadConfig`` - Command ``Restart 2`` to halt system. Needs hardware reset or power cycle to restart (#9046) - Command ``SetOption102 0/1`` to switch between Teleinfo French Metering mode, legacy 1200 bps (0) or Linky standard 9600 bps (1) ### Changed - Triple-mode TLS via configuration in a single firmware (TLS AWS IoT, Letsencrypt and No-TLS) ### Fixed - ESP32 PWM range ## [8.4.0] - 20200730 - Release George ## [8.3.1.7] - 20200716 ### Added - Command ``DzSend ,`` to send values or state to Domoticz - Command ``SetOption100 0/1`` to remove Zigbee ``ZbReceived`` value from ``{"ZbReceived":{xxx:yyy}}`` JSON message - Command ``SetOption101 0/1`` to add the Zigbee source endpoint as suffix to attributes, ex `Power3` instead of `Power` if sent from endpoint 3 - Command (``S``)``SerialSend6`` \ (#8937) - Support for Sonoff Zigbee Bridge as module 75 (#8583) ### Changed - Limited support of Arduino IDE as an increasing amount of features cannot be compiled with Arduino IDE - All timer references from ``Arm`` to ``Enable`` in GUI, ``Timer`` command and JSON message - Domoticz commands prefix from ``Domoticz`` to ``Dz`` - ``Ping`` now reports the hostname instead of IP address (#8948) - Zigbee randomizing of parameters at first run or after Reset ### Removed - Remove Arduino ESP8266 Core support for versions before 2.7.1 ## [8.3.1.6] - 20200617 ### Added - Command ``Module2`` to configure fallback module on fast reboot (#8464) - Command ``SetOption97 0/1`` to switch between Tuya serial speeds 9600 bps (0) or 115200 bps (1) - Command ``SetOption98 0/1`` to provide rotary rule triggers (1) instead of controlling light (0) - Command ``SetOption99 0/1`` to enable zero cross detection on PWM dimmer - Support for Energy sensor (Denky) for French Smart Metering meter provided by global Energy Providers, need a adaptater. See dedicated full [blog](http://hallard.me/category/tinfo/) about French teleinformation stuff - Library to be used for decoding Teleinfo (French Metering Smart Meter) - Support for single wire LMT01 temperature Sensor by justifiably (#8713) - Compile time interlock parameters (#8759) - Compile time user template (#8766) - Rotary encoder support for light dimmer and optional color temperature if button1 still pressed (#8670) - Support for switches/relays using an AC detection circuitry e.g. MOES MS-104B or BlitzWolf SS5 (#8606) - Support for Schneider Electric iEM3000 series Modbus energy meter by Marius Bezuidenhout ### Changed - ESP32 USER GPIO template representation decreasing template message size - Define ``USE_TASMOTA_SLAVE`` into ``USE_TASMOTA_CLIENT`` - Commands ``SlaveSend`` and ``SlaveReset`` into ``ClientSend`` and ``ClientReset`` - IRremoteESP8266 library updated to v2.7.8 ### Fixed - Exception or watchdog on rule re-entry (#8757) ## [8.3.1.5] - 20200616 ### Added - ESP32 ethernet commands ``EthType 0/1``, ``EthAddress 0..31`` and ``EthClockMode 0..3`` - Zigbee initial support for EmberZNet protocol (raw send/receive only) ## [8.3.1.4] - 20200615 ### Added - Basic support for ESP32 ethernet adding commands ``Wifi 0/1`` and ``Ethernet 0/1`` both default ON ## [8.3.1.3] - 20200611 ### Added - Initial support for Telegram bot (#8619) - Support for HP303B Temperature and Pressure sensor by Robert Jaakke (#8638) - Rule trigger ``System#Init`` to allow early rule execution without wifi and mqtt initialized yet - Serial to TCP bridge, ``TCPStart`` and ``TCPBaudRate`` (needs #define USE_TCP_BRIDGE) ## [8.3.1.2] - 20200522 ### Added - Command ``Time 4`` to display timestamp using milliseconds (#8537) - Command ``SetOption94 0/1`` to select MAX31855 or MAX6675 thermocouple support (#8616) - Commands ``LedPwmOn 0..255``, ``LedPwmOff 0..255`` and ``LedPwmMode1 0/1`` to control led brightness by George (#8491) - Three Phase Export Active Energy to SDM630 driver - Wildcard pattern ``?`` for JSON matching in rules - Support for unique MQTTClient (and inherited fallback topic) by full Mac address using ``mqttclient DVES_%12X`` (#8300) - Zigbee options to ``ZbSend`` to write and report attributes - ``CpuFrequency`` to ``status 2`` - ``FlashFrequency`` to ``status 4`` - Support for up to two BH1750 sensors controlled by commands ``BH1750Resolution`` and ``BH1750MTime`` (#8139) - Zigbee auto-responder for common attributes - Support for BL0940 energy monitor as used in Blitzwolf BW-SHP10 (#8175) ### Changed - Energy JSON Total field from ``"Total":[33.736,11.717,16.978]`` to ``"Total":33.736,"TotalTariff":[11.717,16.978]`` - Energy JSON ExportActive field from ``"ExportActive":[33.736,11.717,16.978]`` to ``"ExportActive":33.736,"ExportTariff":[11.717,16.978]`` - Adafruit_SGP30 library from v1.0.3 to v1.2.0 (#8519) ### Fixed - Escape of non-JSON received serial data (#8329) ## [8.3.1.1] - 20200518 ### Added - Command ``Rule0`` to change global rule parameters - More functionality to ``Switchmode`` 11 and 12 (#8450) - Dump of compressed rules over 512 chars and unishox decompress fix - Support for VEML6075 UVA/UVB/UVINDEX Sensor by device111 (#8432) - Support for VEML7700 Ambient light intensity Sensor by device111 (#8432) ### Changed - IRremoteESP8266 library updated to v2.7.7 ## [8.3.1] - 20200518 - Release Fred ## [8.3.0.2] - 20200517 ### Added - Command ``DeviceName`` defaults to FriendlyName1 and replaces FriendlyName1 in GUI ### Changed - Hass discovery from using template name to new Device name (#8462) ## [8.3.0.1] - 20200514 ### Changed - KNX pow function to approximative pow saving 5k of code space - Mutichannel Gas sensor pow function to approximative pow saving 5k of code space - Quick Power Cycle detection from 4 to 7 power interrupts (#4066) ### Fixed - Fix default state of ``SetOption73 0`` for button decoupling and send multi-press and hold MQTT messages ## [8.3.0] - 20200514 - Release Fred ## [8.2.0.6] - 20200501 ### Added - Experimental basic support for Tasmota on ESP32 based on work by Jörg Schüler-Maroldt - Support for analog anemometer by Matteo Albinola (#8283) - Support for OpenTherm by Yuriy Sannikov (#8373) - Support for Thermostat control by arijav (#8212) - Automatic compression of Rules to achieve ~60% compression by Stefan Hadinger - Command ``SetOption93 1`` to control caching of compressed rules - Rule trigger at root level like ``on loadavg<50 do power 2 endon`` after ``state`` command - Zigbee support for router and end-device mode ### Changed - Flash access removing support for any Core before 2.6.3 - HAss discovery by Federico Leoni (#8370) - Default PWM Frequency to 977 Hz from 223 Hz - Minimum PWM Frequency from 100 Hz to 40 Hz - PWM updated to the latest version of Arduino PR #7231 - Philips Hue emulation now exposes modelId and manufacturerId ## [8.2.0.5] - 20200425 ### Changed - Breaking Change Device Groups multicast address and port (#8270) - IRremoteESP8266 library updated to v2.7.6 ## [8.2.0.4] - 20200417 ### Added - Config version tag - Command ``SetOption73 1`` for button decoupling and send multi-press and hold MQTT messages by Federico Leoni (#8235) - Command ``SetOption92 1`` to set PWM Mode from regular PWM to ColorTemp control (Xiaomi Philips ...) - Command ``SO`` as shortcut for command ``SetOption`` ### Changed - PWM implementation to Arduino #7231 removing support for Core versions before 2.6.3 - Default PWM Frequency to 223 Hz instead of 880 Hz for less interrupt pressure ### Fixed - Fix Zigbee DimmerUp/DimmerDown malformed ## [8.2.0.3] - 20200329 ### Added - Support for longer template names - Zigbee command ``ZbBindState`` and ``manuf``attribute - Zigbee command ``ZbConfig`` and configuration in Settings - Commands ``CounterDebounceLow`` and ``CounterDebounceHigh`` to control debouncing (#8021) - Commands ``NrfPage``, ``NrfIgnore``, ``NrfScan`` and ``NrfBeacon`` to NRF24 Bluetooth driver (#8075) - Command ``SetOption90 1`` to disable non-json MQTT messages (#8044) - Command ``Sensor10 0/1/2`` to control BH1750 resolution - 0 = High (default), 1 = High2, 2 = Low (#8016) - Command ``Sensor10 31..254`` to control BH1750 measurement time which defaults to 69 (#8016) - Command ``Sensor18 0..32000`` to control PMS5003 sensor interval to extend lifetime by Gene Ruebsamen (#8128) - Command ``SetOption91 1`` to enable fading at startup / power on - Command ``SetOption41 `` to force sending gratuitous ARP every seconds - Command ``DevGroupName`` to specify up to four Device Group Names (#8087) - Command ``DevGroupSend`` to send an update to a Device Group (#8093) - Command ``Ping`` (#7176) - Command ``Palette`` to add the ability to specify a palette of colors (#8150) - Commands ``GlobalTemp`` and ``GlobalHum`` to init sensor data (#8152) - Quick wifi reconnect using saved AP parameters when ``SetOption56 0`` (#3189) - More accuracy to GPS NTP server (#8088) - Support for an iAQ sensor (#8107) - Support for Seven Segment display using HT16K33 (#8116) - Support for AS3935 Lightning Sensor by device111 (#8130) - ``DimmerRange`` for PWM lights (#8120) ### Changed - Light scheme 2,3,4 cycle time speed from 24,48,72,... seconds to 4,6,12,24,36,48,... seconds (#8034) - Remove floating point libs from IRAM - Remove MQTT Info messages on restart for DeepSleep Wake (#8044) - IRremoteESP8266 library updated to v2.7.5 ### Fixed - PWM flickering during wifi connection (#8046) - Zigbee crash with Occupancy sensor (#8089) - Prevent multiple pings to run concurrently - Scheme 2-4 brightness when SetOption68 1 (#8058) ## [8.2.0.2] - 20200328 ### Added - Support for up to four MQTT GroupTopics using the same optional Device Group names (#8014) - Console command history (#7483, #8015) ## [8.2.0.1] - 20200321 ### Added - Zigbee command ``ZbRestore`` to restore device configuration dumped with ``ZbStatus 2`` - Zigbee command ``ZbUnbind`` - Support for unreachable (unplugged) Zigbee devices in Philips Hue emulation and Alexa - Support for 64x48 SSD1306 OLED (#6740) ### Changed - HM-10 sensor type detection and add features (#7962) ### Fixed - Possible Relay toggle on (OTA) restart - Zigbee sending wrong Sat value with Hue emulation ## [8.2.0] - 20200321 - Release Elliot ## [8.1.0.11] - 20200313 ### Added - HAss Discovery support for Button and Switch triggers by Federico Leoni (#7901) - Support for HDC1080 Temperature and Humidity sensor by Luis Teixeira (#7888) - Commands ``SwitchMode 13`` PushOn and ``SwitchMode 14`` PushOnInverted (#7912) - Command ``HumOffset -10.0 .. 10.0`` to set global humidity sensor offset (#7934) - Zigbee support for Hue emulation by Stefan Hadinger - Dew Point to Temperature and Humidity sensors - Support for ElectriQ iQ-wifiMOODL RGBW light by Ian King (#7947) ### Changed - Zigbee simplification of devices probing, saving Flash and memory ## [8.1.0.10] - 20200227 ### Added - Support for Jarolift rollers by Keeloq algorithm - Zigbee features and improvements and remove support for Zigbee commands starting with ``Zigbee...`` - Support for MaxBotix HRXL-MaxSonar ultrasonic range finders by Jon Little (#7814) - Support for Romanian language translations by Augustin Marti - Support for La Crosse TX23 Anemometer by Norbert Richter (#3146, #7765) - Command ``SetOption89 0/1`` for Zigbee distinct MQTT topics per device for SENSOR, allowing retained messages (#7835) ### Changed - Default my_user_config.h driver and sensor support removing most sensors and adding most drivers - IRremoteESP8266 library updated to v2.7.4 - Revert switchmode 6 according to issue 7778 (#7831) - Hue emulation code optimization ## [8.1.0.9] - 20200220 ### Added - Initial support for Sensors AHT10 and AHT15 by Martin Wagner (#7596) - Support for Wemos Motor Shield V1 by Denis Sborets (#7764) - Zigbee enhanced commands decoding, added ``ZbPing`` - Commands ``SetOption85 0/1`` and ``DevGroupShare`` supporting UDP Group command using ``GroupTopic`` without MQTT by Paul Diem (#7790) - Support for Martin Jerry/acenx/Tessan/NTONPOWER SD0x PWM dimmer switches by Paul Diem (#7791) - Command ``SetOption86 0/1`` for PWM dimmer to turn brightness LED's off 5 seconds after last change - Command ``SetOption87 0/1`` for PWM dimmer to turn red LED on when powered off - Command ``SetOption88 0/1`` for PWM dimmer to let buttons control remote devices ### Changed - Revert most wifi connectivity changes introduced in 8.1.0.5 (#7746, #7602, #7621) ### Fixed - Zigbee auto-increment transaction number (#7757) ## [8.1.0.8] - 20200212 ### Added - Another new DHT driver based on ESPEasy. The old driver can still be used using define USE_DHT_OLD. The previous new driver can be used with define USE_DHT_V2 (#7717) ### Changed - MQTT message size with additional 200 characters - Some wifi code to attempt faster connection (#7621) - Display of some date and time messages from "Wed Feb 19 10:45:12 2020" to "2020-02-19T10:45:12" ### Fixed - Relation between RSSI and signal strength ## [8.1.0.7] - 20200210 ### Added - New DHT driver. The old driver can still be used using define USE_DHT_OLD (#7468) ### Fixed - wrong encoding of Zigbee persistent data ## [8.1.0.6] - 20200205 ### Added - Support for sensors DS18x20 and DHT family on Shelly 1 and Shelly 1PM using Shelly Add-On adapter (#7469) - Commands ``SwitchMode 11`` PushHoldMulti and ``SwitchMode 12`` PushHoldInverted (#7603) - Command ``Buzzer -1`` for infinite mode and command ``Buzzer -2`` for following led mode (#7623) - Support for MI-BLE sensors using HM-10 Bluetooth 4.0 module by Christian Staars (#7683) - BootCount Reset Time as BCResetTime to ``Status 1`` - ``ZbZNPReceived``and ``ZbZCLReceived`` being published to MQTT when ``SetOption66 1`` - Optional Wifi AccessPoint passphrase define WIFI_AP_PASSPHRASE in my_user_config.h (#7690) - Support for FiF LE-01MR energy meter by saper-2 (#7584) ### Fixed - HAss sensor discovery part 1/4 by Federico Leoni (#7582, #7548) - MaxPower functionality (#7647) ## [8.1.0.5] - 20200126 ### Added - ``SetOption84 0/1`` sends AWS IoT device shadow updates (alternative to retained) - ``ZbBind`` (experimental) and bug fixes ### Changed - Wifi connectivity stability (#7602) - IRremoteESP8266 library updated to v2.7.3 ### Fixed - PWM flickering at low levels (#7415) ## [8.1.0.4] - 20200116 ### Added - Web page sliders when ``SetOption37 128`` is active allowing control of white(s) - Zigbee persistence and friendly names - Most SetOptions as defines to my_user_config.h - SoftwareSerial to CSE7766 driver allowing different GPIOs (#7563) - Optional parameter ```` to command ``Scheme , `` to control initial start color - Rule trigger on one level deeper using syntax with two ``#`` like ``on zigbeereceived#vibration_sensor#aqaracubeside=0 do ...`` ### Changed - Zigbee command prefix from ``Zigbee*`` to ``Zb*`` ### Fixed - ``PowerDelta`` zero power detection (#7515) - OTA minimal gzipped detection regression from 8.1.0.3 - ``RGBWWTable`` ignored (#7572) ## [8.1.0.3] - 20200106 ### Added - Support for gzipped binaries - ``SwitchMode 8`` ToggleMulti, ``SwitchMode 9`` FollowMulti and ``SwitchMode 10`` FollowMultiInverted (#7522) ### Changed - Commands ``Prefix``, ``Ssid``, ``StateText``, ``NTPServer``, and ``FriendlyName`` displaying all items - IRremoteESP8266 library updated to v2.7.2 ### Fixed - ``WakeUp `` ignores provided value (#7473) - Exception 9 restart on log message in Ticker interrupt service routines NTP, Wemos and Hue emulation (#7496) ## [8.1.0.2] - 20191230 ### Added - Support for ``AdcParam`` parameters to control ADC0 Current Transformer Apparent Power formula by Jodi Dillon (#7100) - Optional support for Prometheus using file xsns_91_prometheus.ino (#7216) - Command ``ShutterButton `` to control shutter(s) by to-scho (#7403) - Command ``SetOption82 0/1`` to limit the CT range for Alexa to 200..380 - Experimental support for NRF24L01 as BLE-bridge for Mijia Bluetooth sensors by Christian Baars (#7394) - Support to BMP driver to enter reset state (sleep enable) when deep sleep is used in Tasmota ### Fixed - LCD line and column positioning (#7387) - Display handling of hexadecimal escape characters (#7387) - Improved fade linearity with gamma correction - Wrong gamma correction for Module 48 lights (PWM5 for CT) ## [8.1.0.1] - 20191225 ### Added - Command ``SetOption79 0/1`` to enable reset of counters at teleperiod time by Andre Thomas (#7355) - SerialConfig to ``Status 1`` - WifiPower to ``Status 5`` - Support for DS1624, DS1621 Temperature sensor by Leonid Myravjev - Zigbee attribute decoder for Xiaomi Aqara Cube ### Changed - Lights: simplified gamma correction and 10 bits internal computation ### Fixed - Sonoff Bridge, Sc, L1, iFan03 and CSE7766 serial interface to forced speed, config and disable logging - Serial initialization regression from previous fix - Commands ``Display`` and ``Counter`` from overruling command processing (#7322) - ``White`` added to light status (#7142) ## [8.1.0] - 20191225 - Release Doris ## [8.0.0.3] - 20191224 ### Changed - Version bump due to internal Settings change ## [8.0.0.2] - 20191223 ### Added - Zigbee better support for Xiaomi Double Switch and Xiaomi Vibration sensor - Support for ``AdcParam`` parameters to control ADC0 Moisture formula by Federico Leoni (#7309) - Commands ``WebButton1`` until ``WebButton16`` to support user defined GUI button text (#7166) ### Changed - Settings variable namings - Number of ``FriendlyName``s from 4 to 8 ## [8.0.0.1] - 20191221 ### Added - Support for max 150 characters in most command parameter strings (#3686, #4754) - Support for GPS as NTP server by Christian Baars and Adrian Scillato - Zigbee coalesce sensor attributes into a single message - Deepsleep start delay based on Teleperiod if ``Teleperiod`` differs from 10 or 300 ### Changed - Settings text handling allowing variable length text within a total text pool of 699 characters - Smoother ``Fade`` using 100Hz instead of 20Hz animation (#7179) - Number of rule ``Var``s and ``Mem``s from 5 to 16 (#4933) ## [7.2.0] - 20191221 - Release Constance ### Changed - Basic version string to lite (#7291) ### Fixed - Arduino IDE compile error (#7277) - Restore ShutterAccuracy, MqttLog, WifiConfig, WifiPower and SerialConfig (#7281) - No AP on initial install (#7282) - Failing downgrade (#7285) ### 7.1.2.6 20191214 - Change some more Settings locations freeing up space for future single char allowing variable length text - Change tasmota-basic.bin and FIRMWARE_BASIC to tasmota-lite.bin and FIRMWARE_LITE - Fix DeepSleep in case there is no wifi by Stefan Bode (#7213) - Fix Fade would ignore ``savedata 0`` and store to flash anyways (#7262) - Add Zigbee send automatic ZigbeeRead after sending a command - Add Zigbee improving Occupancy:false detection for Aqara sensor - Add fallback support from version 8.x - Add restriction if fallback firmware is incompatible with settings resulting in unreachable device - Add support for DHT12 Temperature and Humidity sensor by Stefan Oskamp ### 7.1.2.5 20191213 - Change some Settings locations freeing up space for future single char allowing variable length text - Add Zigbee support for Xiaomi Aqara Vibration Sensor and Presence Sensor by Stefan Hadinger - Add Shutter functions ramp up/down and MQTT reporting by Stefan Bode ### 7.1.2.4 20191209 - Change HTTP CORS from command ``SetOption73 0/1`` to ``Cors `` allowing user control of specific CORS domain by Shantur Rathore (#7066) - Change GUI Shutter button text to Up and Down Arrows based on PR by Xavier Muller (#7166) - Change amount of supported DHT sensors from 3 to 4 by Xavier Muller (#7167) - Revert removal of exception details from MQTT info on restart - Add Wifi Signal Strength in dBm in addition to RSSI Wifi Experience by Andreas Schultz (#7145) - Add Yaw, Pitch and Roll support for MPU6050 by Philip Barclay (#7058) - Add reporting of raw weight to JSON from HX711 to overcome auto-tare functionality by @tobox (#7171) - Add command ``Sensor34 9 `` to set minimum delta to trigger JSON message by @tobox (#7188) - Fix flashing H801 led at boot by Stefan Hadinger (#7165, #649) - Fix duplicated ``Backlog`` when using Event inside a Backlog by Adrian Scillato (#7178, #7147) - Fix Gui Timer when using a negative zero offset of -00:00 by Peter Ooms (#7174) ### 7.1.2.3 20191208 - Change Exception reporting removing exception details from both MQTT info and ``Status 1``. Now consolidated in ``Status 12`` if available. ### 7.1.2.2 20191206 - Remove rule trigger ``tele_power1#state`` due to compatibility - Add command ``SerialConfig 0..23`` or ``SerialConfig 8N1`` to select Serial Config based in PR by Luis Teixeira (#7108) - Add save call stack in RTC memory in case of crash, command ``Status 12`` to dump the stack by Stefan Hadinger - Add Home Assistant force update by Frederico Leoni (#7140, #7074) ### 7.1.2.1 20191206 - Add SML bus decoder syntax support for byte order by Gerhard Mutz (#7112) - Add rule var ``%topic%`` by Adrian Scillato (#5522) - Add rule triggers ``tele_power1#state`` and multiple ``tele-wifi1#xxx`` by Adrian Scillato (#7093) - Add experimental support for stepper motor shutter control by Stefan Bode - Add optional USE_MQTT_TLS to tasmota-minimal.bin by Bohdan Kmit (#7115) ### 7.1.2 20191206 - Maintenance Release ### 7.1.1.1 20191201 - Fix lost functionality of GPIO9 and GPIO10 on some devices (#7080) - Fix Zigbee uses Hardware Serial if GPIO 1/3 or GPIO 13/15 and SerialLog 0 (#7071) - Fix WS2812 power control (#7090) - Change light color schemes 2, 3 and 4 from color wheel to Hue driven with user Saturation control - Change log buffer size from 520 to 700 characters accomodating full rule text (#7110) ### 7.1.1 20191201 - Maintenance Release ### 7.1.0.1 20191130 - Fix slider for devices with one or two channels like only white or white/yellow - Fix TasmotaSlave buffer overrun on Tele - Fix light scheme 4 speed (#7072) - Add support for TasmotaSlave executing commands on Tasmota ### 7.1.0 20191129 - Release Doris ### 7.0.0.6 20191122 - Add colorpicker to WebUI by Christian Staars (#6984) - Change new Fade system much smoother, Speed now up to 40 (#6942, #3714) - Fix Arduino IDE function prototyping compile error (#6982) - Change update lib IRremoteESP8266 updated to v2.7.1, -2.7k flash and -1.5k RAM for Tasmota-IR - Fix auto--power on/off when setting channel to non-zero or zero value, when SetOption68 1 - Fix postpone saving settings to flash until Fade is complete, avoids pause in Fade - Add command ``SetOption77 0/1`` to keep power on when slider is far left ### 7.0.0.5 20191118 - Fix boot loop regression - Add command ``TempOffset -12.6 .. 12.6`` to set global temperature sensor offset (#6958) - Fix check deepsleep for valid values in Settings (#6961) - Fix Wifi instability when light is on, due to sleep=0 (#6961, #6608) - Add hardware detection to be overruled with ``SetOption51`` (#6969) ### 7.0.0.4 20191108 - Add command ``WifiPower 0 .. 20.5`` to set Wifi Output Power which will be default set to 17dBm - Change supported PCF8574 I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time - Change supported PCF8574A I2C address range to 0x39 - 0x3F allowing other I2C devices with address 0x38 to be used at the same time - Change supported MCP230xx I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time - Add Keep last channels values when Color command end with '=' (#6799) - Add support for I2C sensor TLS2591 Light Intensity sensor (#6873) - Change Kept only NEC/RC5/RC6/HASH IR protocols in standard Tasmota, all other protocols require Tasmota-IR, saving 4K - Add command ``SetOption76 0/1`` to enable incrementing bootcount when deepsleep is enabled (#6930) - Change Reset erase end address from as seen by SDK (getFlashChipSize) to full flash size (getFlashChipRealSize) - Change Zigbee log verbosity reduction ### 7.0.0.3 20191103 - Add command ``I2cDriver`` for I2C driver runtime control using document I2CDEVICES.md - Fix random crash caused by UPNP flood - Add support for Honeywell HPMA115S0 particle concentration sensor by David Hunt (#6843) - Remove driver xsns_12_ads1115_i2cdev replaced by xsns_12_ads1115 ### 7.0.0.2 20191102 - Add command ``WebColor19`` to control color of Module and Name (#6811) - Add support for Honeywell I2C HIH series Humidity and Temperetaure sensor (#6808) - Fix wrong Dimmer behavior introduced with #6799 when ``SetOption37`` < 128 - Change add DS18x20 support in Tasmota-IR - Add Zigbee command support, considered as v1.0 for full Zigbee support - Fix Reduce flash size after change to IRremoteESP8266 v2.7.0 ### 7.0.0.1 20191027 - Remove update support for versions before 6.0 - Change default GUI to dark theme - Add command ``SetOption73 0/1`` to re-enable HTTP Cross-Origin Resource Sharing (CORS) now default disabled (#6767) - Add frequency to ADE7953 energy monitor as used in Shelly 2.5 by ljakob (#6778) - Add command ``SetOption74 0/1`` to enable DS18x20 internal pull-up and remove define DS18B20_INTERNAL_PULLUP (#6795) - Fix better control of RGB/White when ``SetOption37`` >128, added ``Dimmer1`` and ``Dimmer2`` commands (#6714) - Add hide Alexa objects with friendlyname starting with '$' (#6722, #6762) - Add command ``SetOption75 0/1`` to switch between grouptopic (0) using fulltopic replacing %topic% or (1) is cmnd/\ (#6779) - Change IRremoteESP8266 library to v2.7.0 ### 6.7.1.1 20191026 - Change ArduinoSlave to TasmotaSlave - Add support for Tuya battery powered devices (#6735) - Change repository name from Sonoff-Tasmota to Tasmota and all code references from Sonoff to Tasmota ### 6.7.1 20191026 - Release Allison - Fix on energy monitoring devices using PowerDelta Exception0 with epc1:0x4000dce5 = Divide by zero (#6750) - Fix Script array bug (#6751) ### 6.7.0 20191025 - Release ### 6.6.0.21 20191022 - Remove support for WPS and SmartConfig in favour of Web server (!) based WifiManager (#6680) - Remove binary sonoff-classic (#6680) - Remove command ``SetOption2`` ### 6.6.0.20 20191018 - Add command ``SetOption65 0/1`` to disable (1) fast power cycle detection fixing unwanted brownout trigger - Add absolute PowerDelta using command ``PowerDelta 101..32000`` where 101 = 101-100 = 1W, 202 = 202-100 = 102W (#5901) - Add support for EX-Store WiFi Dimmer V4 (#5856) - Add ``ZigbeeRead`` command and many improvements (#6095) - Add ArduinoSlave driver (EXPERIMENTAL) ### 6.6.0.19 20191018 - Replace obsolete xsns_23_sdm120 with xnrg_08_sdm120 and consolidate define USE_SDM120 - Replace obsolete xsns_25_sdm630 with xnrg_10_sdm630 and consolidate define USE_SDM630 - Replace obsolete xsns_49_solaxX1 with xnrg_12_solaxX1 (#6677) ### 6.6.0.18 20191010 - Add command ``DimmerRange`` in Light module to support 2 byte dimming ranges from Tuya - Add Zigbee additional commands and sending messages to control devices (#6095) - Fix Rules were not triggered with IR unknown protocol or in sonoff-it (#6629) - Add define USE_DEEPSLEEP and command ``DeepSleepTime 0 or 10..86400`` (seconds) to enter deepsleep mode (#6638) - Add define USE_SONOFF_RF to enable/disable Sonoff Rf support (#6648) - Add incremental beeps to Ifan03 remote control fan speed buttons (#6636) - Add rule support after every command execution like Fanspeed#Data=2 (#6636) - Fix handling of ligth channels when pwm_multichannel (Option68) is enabled - Add WebUI for multiple, independent PWM channels - Remove default DS18B20 driver and only support define DS18x20 (#6647) - Add support for PMS3003 dust particle sensor - Change Sonoff L1 support by adding define USE_SONOFF_L1 ### 6.6.0.17 20191009 - Add command ``SetOption34 0..255`` to set backlog delay. Default value is 200 (mSeconds) (#6562) - Add command ``Gpio 255`` to show physical GPIO configuration of all non-flash pins (#6407) ### 6.6.0.16 20191008 - Change PZEM004T default address mask from 0.0.0.x to 192.168.1.x for legacy reason (#6585) - Fix PZEM004T, PZEMAC and PZEMDC autodetection (#6585) - Change light drivers internals to ease management ### 6.6.0.15 20191003 - Change command ``PulseTime`` JSON message format and allow display of all pulsetimer information (#6519) - Add support for Chint DDSU666 Modbus energy meter by Pablo Zerón - Add support for SM2135 as used in Action LSC Smart Led E14 (#6495) - Add command ``SetOption72 0/1`` to switch between software (0) or hardware (1) energy total counter (#6561) - Add Zigbee tracking of connected devices and auto-probing of Manuf/Model Ids - Fix better handling of PWM White Temperature mode for Module 48 (#6534) ### 6.6.0.14 20190925 - Change command ``Tariffx`` to allow time entries like 23 (hours), 1320 (minutes) or 23:00. NOTE: As this is development branch previous tariffs are lost! (#6488) - Remove support for define USE_DS18x20_LEGACY and legacy DS18x20 driver (#6486) - Add initial support for MQTT logging using command ``MqttLog `` (#6498) - Add Zigbee more support - collect endpoints and clusters, added ZigbeeDump command - Add initial support for shutters by Stefan Bode (#288) - Add command to MCP230xx: ``sensor29 pin,0/1/2`` for OFF/ON/TOGGLE - Add initial support for PCF8574 I2C I/O Expander (currently output only) by Stefan Bode - Add command ``SetOption71 0/1`` to switch between different Modbus Active Energy registers on DDS238-2 energy meters (#6531) - Change command ``SetOption43`` to make it more general. Now supports PS_16_DZ driver too (#6544) - Change command handling by moving buffers up in chain solving MQTTlog support (#6529) - Change detection of non-MQTT commands by allowing non-space characters as delimiter (#6540) - Fix TasmotaSerial: move serial send to IRAM for high speed baud rates ### 6.6.0.13 20190922 - Add command ``EnergyReset4 x,x`` to initialize total usage for two tarrifs - Add command ``EnergyReset5 x,x`` to initialize total export (or production) for two tarrifs - Add command ``Sensor34 8,0`` and ``Sensor34 8,1`` to disable/enable JSON message on weight change over 4 gram - Add JSON array index support to rules evaluation allowing trigger on ENERGY#POWER[2]>0.60 from JSON ..,"Power":[0.00,0.68],.. (#6160) ### 6.6.0.12 20190910 - Redesign command ``Tariff`` to now default to 0 (=disabled) and allowing to set both Standard Time (ST) and Daylight Savings Time (DST) start hour - Commands ``Tariff1 22,23`` = Tariff1 (Off-Peak) ST,DST Tariff2 (Standard) 6,7 = Tariff2 ST,DST Tariff9 0/1 = Weekend toggle (1 = Off-Peak during weekend) - Change rename "Data" to "Hash" and limit to 32 bits when receiving UNKNOWN IR protocol (see DECODE_HASH from IRremoteESP8266) - Add command ``Gpios 255/All`` to show all available GPIO components (#6407) - Change JSON output format for commands ``Adc``, ``Adcs``, ``Modules``, ``Gpio`` and ``Gpios`` from list to dictionary (#6407) - Add Zigbee support phase 3 - support for Xiaomi lumi.weather air quality sensor, Osram mini-switch - Change energy sensors for three phase/channel support - Add support for Shelly 2.5 dual energy (#6160) - Add initial support for up to three PZEM-014/-016 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315) - Add initial support for up to three PZEM-004T on serial connection with addresses x.x.x.1 (default), 2 and 3 (#2315) - Add initial support for up to three PZEM-003/-017 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315) - Add driver USE_SDM630_2 as future replacement for USE_SDM630 - Pls test and report - Add command ``ModuleAddress 1/2/3`` to set Pzem module address when a single module is connected (#2315) ### 6.6.0.11 20190907 - Change Settings crc calculation allowing short term backward compatibility - Add support for up to 4 INA226 Voltage and Current sensors by Steve Rogers (#6342) - Change Improve reliability of TasmotaSerial at 115200 bauds and reduce IRAM usage for Stage/pre-2.6 - Add support for A4988 stepper-motor-driver-circuit by Tim Leuschner (#6370) - Add support for Hiking DDS238-2 Modbus energy meter by Matteo Campanella (#6384) ### 6.6.0.10 20190905 - Redesign Tuya support by Shantur Rathore removing commands SetOption34, 41, 44, 45, 46 and 65 (#6353) - Add command Reset 99 to reset bootcount to zero (#684, #6351) - Change command Time 1/2/3 to select JSON time format ISO, ISO + Epoch or Epoch for legacy reason ### 6.6.0.9 20190828 - Change theoretical baudrate range to 300..19660500 bps in 300 increments (#6294) - Add Full support of all protocols in IRremoteESP8266, to be used on dedicated-IR Tasmota version. Warning: +81k Flash when compiling with USE_IR_REMOTE_FULL - Add compile time define USE_WS2812_HARDWARE to select hardware type WS2812, WS2812X, WS2813, SK6812, LC8812 or APA106 (DMA mode only) - Add 'sonoff-ir' pre-packaged IR-dedicated firmware and 'sonoff-ircustom' to customize firmware with IR Full protocol support - Add Zigbee support phase 2 - cc2530 initialization and basic ZCL decoding - Add driver USE_SDM120_2 with Domoticz P1 Smart Meter functionality as future replacement for USE_SDM120 - Pls test and report - Add command Power0 0/1/2/Off/On/Toggle to control all power outputs at once (#6340) - Add time to more events (#6337) - Add command Time 1/2/3 to select JSON time format ISO + Epoch, ISO or Epoch ### 6.6.0.8 20190827 - Add Tuya Energy monitoring by Shantur Rathore - Add phase 1 Domoticz P1 Smart Meter support using energy sensors handled by xdrv_03_energy.ino based on an idea by pablozg - Add commands Tariff1 0..23 (start Off-Peak hour), Tariff2 0..23 (start Standard hour) and Tariff3 0/1 (Saturday and Sunday Off-Peak) ### 6.6.0.7 20190825 - Expand Settings area to 4k for future use ### 6.6.0.6 20190819 - Add I2C display driver for SH1106 oled by Gerhard Mutz - Add SPI display drivers for epaper 4.2 inch, ILI9488 TFT, SSD1351 Color oled and RA8876 TFT by Gerhard Mutz - Add support for HM17 bluetooth LE passive scan of ibeacon devices by Gerhard Mutz ### 6.6.0.5 20190816 - Add command WebSensor 0/1 to control display of sensor data in web GUI (#6085) - Change some table locations from RAM to Flash - Fix wrong telemetry message when SetOption68 1 (#6191) - Add support for RDM6300 125kHz RFID Reader by Gerhard Mutz ### 6.6.0.4 20190806 - Add support for CHIRP soil moisture sensor by Christian Baars - Add debug compile features using defines DEBUG_TASMOTA_CORE, DEBUG_TASMOTA_DRIVER and DEBUG_TASMOTA_SENSOR. - See DEBUG_CORE_LOG example in sonoff.ino and DEBUG_DRIVER_LOG example in xdrv_09_timers.ino - Add support for Solax X1 inverter by Pablo Zerón - Add ZigBee support phase 1 - low level MQTT ZNP messages for CC2530 devices - Add command Buzzer with optional parameters ,, enabled when a buzzer is configured (#5988) - Add support for PAJ7620 gesture sensor by Christian Baars ### 6.6.0.3 20190725 - Change filename of configuration backup from using FriendlyName1 to Hostname solving diacritic issues (#2422) - Change Store AWS IoT Private Key and Certificate in SPI Flash avoiding device-specific compilations - Upgrade library IRRemoteEsp8266 to 2.6.4, now using sendPioneer() - Add support for MAX31865 Thermocouple sensor by Alberto Lopez Siemens - Add option 0 to Width1 (Marker), Width2 (Second), Width3 (Minute) and Width4 (Hour) disabling display (#6152) - Add MqttCount metric to STATE (#6155) - Add define USE_ENERGY_MARGIN_DETECTION to disable Energy Margin and Power Limit detection - Add define USE_ENERGY_POWER_LIMIT to disable Energy Power Limit detection while Energy Margin detection is active - Add allow repeat/longpress for IRSend raw, introduced IRSend option (#6074) - Add SetOption68 to enable multi-channel PWM instead of a single light (#6134) ### 6.6.0.2 20190714 - Change commands Var and Mem to show all parameters when no index is given (#6107) - Add command SetOption67 0/1 to disable or enable a buzzer as used in iFan03 - Add command DisplayWidth to set pixel width on supported devices - Add command DisplayHeight to set pixel height on supported devices - Add support for Sonoff iFan03 as module 71 (#5988) - Add support for a buzzer - Add support for IRSend long press ('repeat' feature from IRRemoteESP8266) (#6074) - Add support for IRHVAC Midea/Komeco protocol (#3227) - Add support for more IRSend protocols enabled in my_user_config.h - Add support for IRSend Pioneer protocol (#6100) - Add Oled reset GPIO option "OLED reset" ### 6.6.0.1 20190708 - Fix Domoticz battery level set to 100 if define USE_ADC_VCC is not used (#6033) - Fix Force Elliptic Curve for Letsencrypt TLS #6042 - Fix WeMo emulation for 1G echo and 2G echo dot (#6086) - Fix Xiaomi Philips brightness (#6091) - Change defines USE_TX20_WIND_SENSOR and USE_RC_SWITCH in my_user_config.h to disable to lower iram usage enabling latest core compilation (#6060, #6062) - Add blend RGB leds with White leds for better whites (#5895, #5704) - Add command SetOption41 0..8 to control number of Tuya switches (#6039) - Add command SetOption42 0..255 to set overtemperature (Celsius only) threshold resulting in power off all on energy monitoring devices. Default setting is 90 (#6036) - Add command SetOption66 0/1 to enable or disable Tuya dimmer range 255 slider control - Add command Time to disable NTP and set UTC time as Epoch value if above 1451602800 (=20160101). Time 0 re-enables NTP (#5279) - Add AZ7798 automatic setting of clock display (#6034) - Add Epoch and UptimeSec to JSON messages (#6068) - Add support for up to 4 INA219 sensors (#6046) ### 6.6.0 20190707 - Remove support of TLS on core 2.3.0 and extent support on core 2.4.2 and up - Remove MQTT uptime message every hour - Refactor some defines to const - Refactor webserver HTML input, button, textarea, and select name based on id - Refactor webserver sensor data collection - Refactor TLS based on BearSSL, warning breaking change for fingerprints validation - Refactor management of lights, using classes and integers instead of floats - Refactor UDP initial message handling from string to char using static memory and add debug info (#5505) - Refactor IRSend and receive for 64-bit support (#5523) - Refactor MQTT which might solve issue (#5755) - Refactor IRSend by using heap when more than 199 values need to be send. May need increase of define MQTT_MAX_PACKET_SIZE too (#5950) - Refactor double to float in rules, and replaced trigonometric functions from stdlib with smaller versions (#6005) - Change pubsubclient MQTT_KEEPALIVE from 10 to 30 seconds for AWS IoT support - Change gamma correction as default behavior, ie "Ledtable 1" - Change PWM resolution from 8 to 10 bits for low brightness lights - Change IRSend Panasonic protocol to 64-bit (#5523) - Change ADC0 to enabled by default in my_user_config.h (#5671) - Change define USE_EMULATION by USE_EMULATION_HUE and USE_EMULATION_WEMO (#5826) - Change default PowerDelta from 80% to 0% on new installations (#5858, #5028, #4813, #4130, #4145, #3795, #3778, #3660, #3648) - Fix display Bug in KNX webmenu for Physical Address - Fix the Unescape() function and the SendSerial3 behaviour - Fix webserver multiple Javascript window.onload functionality - Fix TasmotaSerial at 9600 bps solving DFPlayer comms (#5528) - Fix Configure Timer Web GUI (#5568) - Fix Shelly 2.5 I2C address priority issue when VEML6070 code is present by disabling VEML6070 for Shelly 2.5 (#5592) - Fix use of SerialDelimiter value 128 (#5634) - Fix Sonoff Pow R2 / S31 invalid energy increments (#5789) - Fix core 2.5.x ISR not in IRAM exception (#5837) - Fix Philips Hue emulation Alexa issue by using part of MAC address for LightId (#5849) - Fix missing white channel for WS2812 (#5869) - Fix PZem startup issue (#5875) - Fix exception 9 when syslog is enabled and NTP is just synced (#5917) - Fix Toggle functionality to button double press when one button and two devices are detected (#5935) - Fix channel command for dual dimmers (#5940) - Fix not restoring white value on power off/power on (#5993) - Add command AdcParam to control ADC0 Temperature and Light formula parameters - Add command LedMask to assign which relay has access to power LED (#5602, #5612) - Add extended LED power control using command LedPowerX where X is 1 to 4. Enabled when "LedLink(i)" is configured too (#5709) - Add command Sensor20 1..255 to change Nova Fitness SDS01 working period in minutes (#5452) - Add command SetOption38 6..255 to set IRReceive protocol detection sensitivity mimizing UNKNOWN protocols (#5853) - Add command SetOption39 1..255 to control CSE7766 (Pow R2) or HLW8032 (Blitzwolf SHP5) handling of power loads below 6W. Default setting is 128 (#5756) - Add command SetOption40 0..250 to disable button functionality if activated for over 0.1 second. Needs SetOption1 1 and SetOption13 0 (#5449) - Add command SetOption63 0/1 to disable relay state feedback scan at restart (#5594, #5663) - Add command SetOption64 0/1 to switch between "-" or "_" as sensor index separator impacting DS18X20, DHT, BMP and SHT3X sensor names (#5689) - Add command SetOption65 0/1 and more Tuya Serial based device support (#5815) - Add command WebColor to change GUI colors on the fly - Add support for AWS IoT with TLS 1.2 on core 2.4.2 and up. Full doc here: https://github.com/arendst/Tasmota/wiki/AWS-IoT - Add support for Badger HR-E Water Meter (#5539) - Add support for Shelly 2.5 Energy and overtemp Monitoring (#5592) - Add support for color and colortone for Philips Hue emulation via Alexa (#5600 #4809) - Add support for Scripts as replacement for Rules. Default disabled but can be enabled in my_user_config.h (#5689) - Add support for up to four LEDs related to four power outputs. Enabled when "LedLink(i)" is configured too (#5709) - Add support for Shelly 1PM Template {"NAME":"Shelly 1PM","GPIO":[56,0,0,0,82,134,0,0,0,0,0,21,0],"FLAG":2,"BASE":18} (#5716) - Add support for SPS30 Particle sensor thanks to Gerhard Mutz (#5830) - Add support for VL53L0x time of flight sensor. Might interfere with TSL2561 using same I2C address (#5845) - Add support for Sonoff L1 thanks to reef-actor (#6002) - Add rule Http#Initialized - Add rule System#Save executed just before a planned restart - Add rule support for single JSON value pair like {"SSerialReceived":"on"} by expanding it to {"SSerialReceived":{"Data":"on"}} allowing for trigger SSerialReceived#Data=on (#5638) - Add define USE_COUNTER to my_user_config.h to save space in sonoff-basic.bin and sonoff-minimal.bin - Add define USE_DHT to my_user_config.h to save space in sonoff-basic.bin - Add defines USE_EMULATION_WEMO and USE_EMULATION_HUE to my_user_config.h to control emulation features at compile time (#5826) - Add Toggle functionality to button double press when more devices are detected - Add device OverTemp (>73 Celsius) detection to Energy Monitoring devices with temperature sensor powering off all outputs - Add Tuya Dimmer 10 second heartbeat serial packet required by some Tuya dimmer secondary MCUs - Add all temperature, humidity and pressure for global access - Add validation check when loading settings from flash - Add HX711 weight restore after controlled restart or after power restore just before executing command Sensor34 7 (#5367, #5786) - Add GUI hexadecimal color options in my_user_config.h (#5586) - Add alternative IRSend command syntax IRSend raw,\,\
,\
,\,\,\,\ (#5610) - Add user configurable ADC0 to Module and Template configuration compatible with current FLAG options (#5671) - Add AriLux RF control GPIO option "ALux IrSel" (159) replacing "Led4i" (59) for full LED control (#5709) - Add LED GPIO option "LedLink" (157) and "LedLinki" (158) to select dedicated link status LED (#5709) - Add all 5 PWM channels individually adressable with LEDs. (#5741) - Add reset of Energy values when connection to sensor is lost for over 4 seconds (#5874, #5881) - Add checkbox to GUI password field enabling visibility during password entry only (#5934) ### 6.5.0 20190319 - Remove commands SetOption14 and SetOption63 as it has been superseded by command Interlock - Remove command SetOption35 0-255 for mDNS start-up delay (#4793) - Remove support for MQTT_LIBRARY_TYPE, MQTT_ARDUINOMQTT and MQTT_TASMOTAMQTT (#5474) - Change webserver content handling from single String to small Chunks increasing RAM - Change code use of boolean to bool and byte to uint8_t - Change code uint8_t flags to bool flags - Change sonoff_template.h layout regarding optional module flags like ADC0 - Change sonoff_template.h module lay-out by removing non-configurable GPIOs - Change button driver making it modular - Change switch driver making it modular and introduce input filter (#4665, #4724) - Change switch input detection by optimizing switch debounce (#4724) - Change web authentication (#4865) - Change image name BE_MINIMAL to FIRMWARE_MINIMAL and USE_xyz to FIRMWARE_xyz (#5106) - Change GUI weblog from XML to plain text solving possible empty screens (#5154) - Fix most compiler warnings - Fix Display exception 28 when JSON value is nullptr received - Fix epaper driver (#4785) - Fix HAss Sensor Discovery Software Watchdog restart (#4831, #4988) - Fix allowable MAX_RULE_VARS to 16 (#4933) - Fix mDNS addService (#4938, #4951) - Fix HAss discovery of MHZ19(B) sensors (#4992) - Fix some exceptions and watchdogs due to lack of stack space (#5215) - Fix GUI wifi password acception starting with asteriks (*) (#5231, #5242) - Fix command WebSend intermittent results (#5273, #5304) - Fix additional characters in fallbacktopic, hostname and mqttclient on core 2.5.0 (#5359, #5417) - Fix Energy TotalStartTime when commands EnergyReset0 and/or EnergyReset3 used (#5373) - Fix DS18S20 temperature calculation (#5375) - Fix float calculations in range from 0 to -1 (#5386) - Fix exception on GUI Configure Logging and Configure Other (#5424) - Add commands PowerCal, VoltageCal and CurrentCal for HLW8012, HJL01 and BL0937 based energy sensors - Add command SerialDelimiter 128 to filter reception of only characters between ASCII 32 and 127 (#5131) - Add command SSerialSend5 \ to SerialBridge - Add command Interlock 0 / 1 / 1,2 3,4 .. to control interlock ON/OFF and add up to 8 relays in 1 to 4 interlock groups (#4910, #5014) - Add command Template 255 to copy module configuration over to current active template and store as user template named Merged (#5371) - Add command WifiConfig 7 to allow reset of device in AP mode without admin password (#5297) - Add command SetOption36 to control boot loop default restoration (#4645, #5063) - Add command SetOption37 for RGBCW color mapping (#5326) - Add command SetOption55 0/1 and define MDNS_ENABLE to disable/enable mDNS (#4793, #4923) - Add command SetOption62 0/1 to disable retain on Button or Switch hold messages (#5299) - Add support for Smanergy KA10 Smart Wall Socket with Energy monitoring - Add support for commands in sensor drivers - Add support for MAX31855 K-Type thermocouple sensor using softSPI (#4764) - Add support for Near Field Communication (NFC) controller PN532 using Serial (#4791, #5162) - Add support for OBI Power Socket 2 (#4829) - Add support for YTF IR Bridge (#4855) - Add support for Mi LED Desk Lamp with rotary switch (#4887) - Add support for Digoo DG-SP202 Smart Socket with Energy monitoring (#4891) - Add support for MAX44009 Ambient Light sensor (#4907) - Add support for inverted buttons and inverted buttons without pullup (#4914) - Add support for Luminea ZX2820 Smart Socket with Energy monitoring (#4921) - Add support for multiple ADS1115 I2C devices (#5083) - Add support for online template change using command Template or GUI Configure Other (#5177) - Add support for Korean language translations (#5344) - Add support for sensor SCD30 (#5434) - Add parameter CFG_HOLDER to status 1 message (#5206) - Add SetOption32 until SetOption49 diagnostic information to Status 3 report as replacement for second property value in SetOption property name - Add Resolution property to Status 3 report providing previous SetOption second value property - Add property MqttCount to status 6 message representing number of Mqtt re-connections - Add property LinkCount to state and status 11 message representing number of Wifi Link re-connections - Add property Downtime to state and status 11 message representing the duration of wifi connection loss - Add variable %timestamp% to rules (#4749) - Add rule support for "==", "!=" ">=" and "<=" (#5122) - Add rule expression enabled by define USE_EXPRESSION in my_user_config.h (#5210) - Add Power status functionality to LED2 when configured leaving LED1 for Link status indication - Add user configuration of HLW8012 and HJL-01/BL0937 Energy Monitoring as used in Sonoff Pow and many Tuya based devices - Add user configuration of MCP39F501 Energy Monitoring as used in Shelly2 - Add online template configuration using both commands and Configure Template menu option in GUI - Add (S)SerialSend3 escape sequence \x to allow hexadecimal byte value (#3560, #4947) - Add define DS18B20_INTERNAL_PULLUP to select internal input pullup when only one DS18B20 sensor is connected eliminating external resistor (#4738) - Add button control when no relay configured (#4682) - Add startup delay of 4 seconds to button control (#4829) - Add core version conditional compile options to provided PWM files (#4917) - Add resiliency to saved Settings (#5065) - Add MHZ19 Temperature as Domoticz Temperature selection (#5128) - Add HAss status sensor (#5139) - Add status message to former declined group commands (#5145) - Add 0x to IRRemote (SetOption29) and RCSwitch (SetOption28) received hexadecimal data (#5431) ### 6.4.1 20181224 - Change RAM usage BMP/BME I2C sensors - Change FallbackTopic from cmnd/\/ to cmnd/\_fb/ to discriminate from Topic (#1528) - Change FallbackTopic detection (#4706) - Change Hass discovery to short MQTT messages as used by Hass 0.81 and up (#4711) - Change MQTT GUI password handling (#4723) - Fix possible dtostrf buffer overflows by increasing buffers - Fix wifi strongest signal detection (#4704) - Fix Alexa "this value is outside the range of the device". Needs power cycle and Alexa deletion/discovery cycle. (#3159, #4712) - Add Slovak language file (#4663) - Add support for AZ-Instrument 7798 CO2 meter/datalogger (#4672) - Add define WIFI_SOFT_AP_CHANNEL in my_user_config.h to set Soft Access Point Channel number between 1 and 13 as used by Wifi Manager web GUI (#4673) - Add define USE_MQTT_TLS_CA_CERT for checking MQTT TLS against root ca using Let's Encrypt cert from sonoff_letsencrypt.h - not supported with core 2.3.0 (#4703) ### 6.4.0 20181217 - Change GUI Configure Module by using AJAX for data fetch to cut page size (and memory use) by 40% In case of web page errors clear your browser cache or do Page Reload (F5 or Ctrl+R) - Change enforcing flashmode dout but it is still mandatory - Change bootcount update (being first) flash write to 10 seconds after restart - Change display and epaper drivers - Change command WebSend Host header field from IP address to hostname (#4331) - Change log buffer size from 512 to 520 to accommodate http sensor data (#4354) - Change default WIFI_CONFIG_TOOL from WIFI_WAIT to WIFI_RETRY in my_user_config.h (#4400) - Change webgui refresh time delay for Save Settings and local OTA Upload (#4423) - Change SR-04 driver to use NewPing library (#4488) - Change MCP230xx driver to support interrupt retention over teleperiod (#4547) - Change support for MPU6050 using DMP (#4581) - Fix unintended function overload of WifiState - Fix wifi connection errors using wifi disconnect and ESP.reset instead of ESP.restart - Fix Sonoff Pow R2 and Sonoff S31 Serial interface hang caused by Sonoff Basic R2 driver delay implementation (and possibly core bug) - Fix MQTT connection error after restart - Fix wifi re-scan connection baseline - Fix possible strncat buffer overflows - Fix intermittent Pzem sensor energy overflow calculation error - Fix shelly2 ghost switching caused by lack of pull-up inputs (#4255) - Fix hardware serial pin configuration. To keep using hardware serial swap current Rx/Tx pin configuration only (#4280) - Fix MqttRetry values above 255 seconds (#4424) - Fix WifiManager functionality on initial installation (#4433) - Fix ArduinoOTA for Core 2.5.0 (#4620) - Add minutes to commands Timezone to allow all possible world timezones - Add more strict checks for GPIO selections - Add code image and optional commit number to version - Add dynamic delay to main loop providing time for wifi background tasks - Add additional start-up delay during initial wifi connection - Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver - Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver - Add user definition of defines WIFI_RSSI_THRESHOLD (default 10) and WIFI_RESCAN_MINUTES (default 44) - Add command SetOption58 0/1 to enable IR raw data info in JSON message (#2116) - Add command IRSend |0,,,.. to allow raw data transmission (#2116) - Add command SetOption56 0/1 to enable wifi network scan and select highest RSSI (#3173) - Add command SetOption57 0/1 to enable wifi network re-scan every 44 minutes with a rssi threshold of 10 to select highest RSSI (#3173) - Add support for SDM220 (#3610) - Add default sleep 1 to sonoff-basic to lower energy consumption (#4217) - Add wifi status to Tuya (#4221) - Add delays to reduce CPU usage at boot time (#4233) - Add command SetOption24 0/1 to select pressure unit as hPa or mmHg (#4241) - Add optional hardware serial when GPIO13(Rx) and GPIO15(Tx) are selected removing hardware serial from GPIO01(Tx) and GPIO03(Rx) (#4288) - Add support for Gosund SP1 v2.3 Power Socket with Energy Monitoring (#4297) - Add support for Armtronix dimmers. See wiki for info (#4321) - Add to command WebSend option to send a direct path when command starts with a slash (#4329) - Add support for LG HVac and IrRemote (#4377) - Add initial support for Hass sensor discovery (#4380) - Add support for Fujitsu HVac and IrRemote (#4387) - Add support for I2C MGC3130 Electric Field Effect sensor by Christian Baars (#3774, #4404) - Add command CalcRes to set number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE (#4420) - Add CPU average load to state message (#4431) - Add command SetOption59 0/1 to change state topic from tele/STATE to stat/RESULT (#4450) - Add support for SM Smart Wifi Dimmer PS-16-DZ (#4465) - Add support for Teckin US Power Socket with Energy Monitoring (#4481) - Add command SetOption60 0/1 to select dynamic sleep (0) or sleep (1) (#4497) - Add support for iFan02 Fanspeed in Domoticz using a selector (#4517) - Add support for GPIO02 for newer Sonoff Basic (#4518) - Add Announce Switches to MQTT Discovery (#4531) - Add support for Manzoku Power Strip (#4590) ### 6.3.0 20181030 - Change web Configure Module GPIO drop down list order for better readability - Change status JSON message providing more switch and retain information - Change xsns_17_senseair.ino to use TasmotaModbus library - Change MCP230xx driver - Change PubSubClient Mqtt library to non-blocking EspEasy version - Change energy monitoring using energy sensor driver modules - Change Webserver page handler for easier extension (thx to Adrian Scillato) - Change pinmode for no-pullup defined switches to pullup when configured as switchmode PUSHBUTTON (=3 and up) (#3896) - Change default OTA Url to http://thehackbox.org/tasmota/release/sonoff.bin (#4170) - Remove support for MQTT Client esp-mqtt-arduino by #define MQTT_LIBRARY_TYPE MQTT_ESPMQTTARDUINO - Remove commands PowerCal, VoltageCal and CurrentCal as more functionality is provided by commands PowerSet, VoltageSet and CurrentSet - Remove restart after ntpserver change and force NTP re-sync (#3890) - Fix showing Period Power in energy threshold messages - Fix header file execution order by renaming user_config.h to my_user_config.h - Fix some TSL2561 driver issues (#3681) - Fix KNX PA exception. Regression from 6.2.1 buffer overflow caused by subStr() (#3700, #3710) - Fix setting and getting color temperature for Philips Hue emulation (#3733) - Fix ButtonRetain to not use default topic for clearing retain messages (#3737) - Fix syslog when emulation is selected (#2109, #3784) - Fix rule trigger POWER1#STATE execution after restart and SetOption0 is 0 (#3856) - Fix Home Assistant forced light discovery (#3908) - Fix invalid configuration restores and decode_config.py crc error when savedata = 0 (#3918) - Fix timer offset -00:00 causing 12:00 hour offset (#3923) - Fix I2CScan invalid JSON error message (#3925) - Fix exception when wrong Domoticz JSON message is received (#3963) - Fix Sonoff Bridge RfRaw receive (#4080, #4085) - Fix possible wifi connection error (#4044, #4083) - Fix invalid JSON floating point result from nan (Not a Number) and inf (Infinity) into null (#4147) - Fix rule mqtt#connected trigger when mqtt is disabled (#4149) - Add support for LCD, Matrix, TFT and Oled displays - Add support for Neo Coolcam Wifi Smart Power Plug - Add support for Michael Haustein ESP Switch - Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT - Add support for Neo Coolcam Wifi Smart Power Plug - Add support for Michael Haustein ESP Switch - Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT - Add support for DS3231 Real Time Clock - Add support for HX711 Load Cell with optional web GUI scale interface to demonstrate easy GUI plug-in - Add support for serial 8N2 communication to TasmotaModbus and TasmotaSerial libraries - Add support for RF transceiving using library RcSwitch (#2702) - Add support for Shelly 1 and Shelly 2 (#2789) - Add support for La Crosse TX20 Anemometer (#2654, #3146) - Add support for MP3 player using DFRobot RB-DFR-562 (#3723) - Add Support for Xiaomi-Philips Bulbs (#3787) - Add support for PCA9685 12bit 16pin hardware PWM driver (#3866) - Add support for EXS Relay V5.0 (#3810) - Add support for OBI Power Socket (#1988, #3944) - Add support for Teckin Power Socket with Energy Monitoring (#3950) - Add support for Pzem-003/017 DC Energy monitoring module (#3694) - Add support for Pzem-014/016 AC Energy monitoring module (#3694) - Add support for CSL Aplic WDP 303075 Power Socket with Energy Monitoring (#3991, #3996) - Add support for Tuya Dimmer (#469, #4075) - Add command Display to show all settings at once - Add command SerialSend5 to send raw serial data like "A5074100545293" - Add command WebRefresh 1000..10000 to control web page refresh in milliseconds. Default is 2345 - Add command WeightRes 0..3 to control display of decimals for kilogram - Add command RGBWWTable to support color calibration (#3933) - Add command Reset 4 (reset to defaults but keep wifi params) and Reset 5 (as reset 4 and also erase flash) (#4061) - Add command SetOption35 0..255 (seconds) to delay mDNS initialization to control possible Wifi connect problems - Add command SetOption52 0/1 to control display of optional time offset from UTC in JSON messages (#3629, #3711) - Add command SetOption53 0/1 to toggle gui display of Hostname and IP address (#1006, #2091) - Add authentication to HTTP web pages - Add decimals as input to commands PowerSet, VoltageSet and CurrentSet - Add tools/decode-config.py by Norbert Richter to decode configuration data. See file for information - Add define USE_DISPLAYS for selecting image sonoff-display - Add define USE_BASIC for selecting image sonoff-basic without most sensors - Add auto reload of main web page to some web restarts - Add TasmotaModbus library as very basic modbus wrapper for TasmotaSerial - Add more API callbacks and document API.md - Add Apparent Power and Reactive Power to Energy Monitoring devices (#251) - Add token %hostname% to command FullTopic (#3018) - Add Wifi channel number to state message (#3664) - Add user configurable GPIO02 and GPIO03 on H801 devices (#3692) - Add toggle function RGBW lights (#3695, #3697) - Add network information to display start screen (#3704) - Add sleep to Nova Fitness SDS01X sensor (#2841, #3724, #3749) - Add Analog input AD0 enabled to sonoff-sensors.bin (#3756, #3757) - Add power value below 5W to Sonoff Pow R2 and S31 (#3745) - Add RF Receiver control to module MagicHome to be used on Arilux LC10 (#3792) - Add userid/password option to decode-status.py (#3796) - Add delay after restart before processing rule sensor data (#3811) - Add force_update to Home Assistant discovery (#3873) - Add rule triggers SWITCH1#BOOT and POWER1#BOOT (#3904, #3910) - Add Hebrew language file (#3960) - Add TotalStartTime to Energy JSON message (#3971) - Add whitespace removal from RfRaw and SerialSend5 (#4020) - Add support for two BMP/BME sensors (#4195) ### 6.2.1 20180905 - Fix possible ambiguity on command parameters if StateText contains numbers only (#3656) - Fix Wemo emulation to select the first relay when more than one relay is present (#3657) - Fix possible exception due to buffer overflow (#3659) - Fix lost energy today and total energy value after power cycle (#3689) ### 6.2.0 20180901 - Allow user override of define MAX_RULE_VARS and MAX_RULE_TIMERS (#3561) - Disable wifi sleep for both Esp8266/Arduino core 2.4.1 and 2.4.2 to solve device freeze caused by Espressif SDK bug (#3554) - Change DS18B20 driver to provide better instant results - Change some sensor drivers to provide instant results - Change define USE_ALL_SENSORS to USE_SENSORS as it doesn't contain all sensors due to duplicate I2C addresses - Change some sensor update timings: AdcEvery 200 -> 250, Senseair 300 -> 250, SDM120 300 -> 250, SDM630 300 -> 250 - Change default Wifi config option from WPS to Wifi Manager if WPS is disabled or Wifi Smartconfig if webserver is disabled or Wifi Serial input if Smartconfig is disabled - Change SHT1x driver to provide better instant results and fix I2C interference - Change DHT driver to provide better instant results and add decimals to DHT11 (#3164) - Change DS18x20 driver to provide better instant results (#3169) - Change CounterType 1 from milliseconds to microseconds (#3437) - Change scheduler for better sleep support using Uptime, Delay, PulseTime and TelePeriod, Blinktime (#3581) - Remove unused functionality from Sonoff-minimal to save space - Remove WPS and SmartConfig from sonoff-minimal saving 56k code space - Remove TSL2561 debug message and update library (#2415) - Remove forced restart when sleep command is executed (#3554) - Fix invalid response using more than 4 switches and domoticz - Fix sonoff-minimal not using default settings - Fix unsecure main webpage update - Fix DHT driver mixing values for different sensors (#1797) - Fix EnergyReset3 regression not clearing total energy (#2723) - Fix rules once regression from v6.1.0 (#3198, #3226) - Fix command Scale buffer overflow (#3236) - Fix possible WDT due to long MQTT publish handling (#3313) - Fix command TimeDst/TimeStd invalid JSON (#3322) - Fix handling of default names when using names starting with shortcut character ",0,1 or 2 (#3392, #3600, #3618) - Fix LM75AD I2C sensor detection (#3408) - Fix iFan02 power on state (#3412, #3530) - Fix some Pow R2 and S31 checksum errors using optimized re-sync (#3425) - Fix SDM120 reporting wrong negative values to Domoticz (#3521) - Fix MQTT reconnection detection when using TasmotaMqtt library (#3558) - Fix OtaMagic when file path contains a dash (-) (#3563) - Fix Sonoff Bridge data reception when using Portisch EFM8 firmware using in data buffer length (#3605) - Add read sensor retry to DS18B20, DS18x20, DHT, SHT1X and HTU21 - Add user selection of Wifi Smartconfig as define USE_SMARTCONFIG in user_config.h - Add boot loop detection and perform some solutions - Add wifi and mqtt status led blinkyblinky to be disabled by SetOption31 1. Does not work when LedPower is On (deliberate) (#871, #2230, #3114, #3155) - Add support for TM1638 switch (#2226) - Add GPIO options ButtonXn, SwitchXn and CounterXn to select INPUT mode instead of INPUT_PULLUP (#2525) - Add support for APDS9960 proximity sensor (#3051) - Add support for MPR121 controller in input mode for touch buttons (#3142) - Add support for MCP230xx for general purpose input expansion and command Sensor29 (#3188) - Add default Wifi Configuration tool as define WIFI_CONFIG_NO_SSID in user_config.h if no SSID is configured (#3224) - Add command Timers 0/1 to globally disable or enable armed timers (#3270) - Add support for CCS811 sensor (#3309) - Add Turkish language file (#3332) - Add command SerialSend4 to send binary serial data (#3345) - Add initial support for sensor MPU6050 (#3352) - Add rule triggers Wifi#Connected and Wifi#Disconnected (#3359) - Add option + to command Rule to concatenate new rule with existing rules (#3365) - Add message when JavaScript is not enabled in webbrowser (#3388) - Add build time setting of ButtonTopic and SwitchTopic (#3414) - Add iFan02 Fanspeed + and Fanspeed - command options (#3415) - Add Individual HSBColorX commands (#3430, #3615) - Add output support on MCP23008/MCP23017 (#3436) - Add modulo option to rules like rule1 on Time#Minute|5 do backlog power on;delay 200;power off endon (#3466) - Add RGB support for Domoticz (#3547) - Add all ruletimer values to command RuleTimer result message (#3571) - Add command Publish2 for publishing retained MQTT messages (#3593) - Add commands ButtonDebounce 40..1000 and SwitchDebounce 40..1000 to have user control over debounce timing. Default is 50mS (#3594) - Add RuleX debug options 8,9,10 (StopOnError) to control RuleX execution status after an exception restart (#3607) - Add rule variables %sunrise%, %sunset%, %uptime% and %time% (#3608) - Add optional MQTT_TELE_RETAIN to Energy Margins message (#3612, 3614) ### 6.1.1 20180714 - Revert wifi changes (#3177) - Revert sonoff-minimal removals causing failure of wifi connection (#3177) ### 6.1.0 20180706 - Remove version 3, 4 and pre 5.2 settings auto-upgrade. See https://github.com/arendst/Tasmota/wiki/Upgrading#migration-path - Change default CFG_HOLDER from 0x20161209 to 4617 (=0x1209) - no impact on default upgrades - Change number of supported switches from 4 to 8 (#2885, #3086) - Change BME680 driver from Adafruit to Bosch BME680 library (#2969) - Fix Pzem004T checksum error - Fix KNX bug when doing reply of sensors values - Fix rules induced LWT message - Fix possible wifi connection problem (#1366) - Fix some Pow R2 and S31 checksum errors (#1907) - Fix display selection of un-available GPIO options in Module Configuration webpage (#2718) - Fix timer re-trigger within one minute after restart (#2744) - Fix IRSend not accepting data value of 0 by David Conran (#2751) - Fix vars on rules by Adrian Scillato (#2769) - Fix bug in KNX menu by Adrian Scillato (#2770) - Fix anomalies in rules (#2778) - Fix HUE bridge V1 software version by Heiko Krupp (#2788) - Fix Hardware Watchdog restart when using event command (#2853) - Add Ukrainian language file - Add KNX support for DS18S20 Temperature sensor - Add CRC to Settings making future upgrades more fail-safe - Add feature information to Status 4 - Add tools folder with python script decode-status.py for decoding some status fields like SetOption and Features - Add Slots on the KNX Web Menu to select Group Addess to receive data to trigger rules - Add two rule sets of 511 characters using commands rule1, rule2 and rule3 - Add Console Commands to send KNX Commands and KNX Values - Add Slots on the KNX Web Menu to select Group Addess to send data from console commands - Add Events to trigger rules when a command or read requests is received from KNX - Add command SetOption30 to enforce Hass discovery as light group (#1784) - Add support for BlitzWolf BW-SHP2 (and Homecube, Gosund SP1) Energy Monitoring Smart Socket (#2223) - Add time in minutes to rule Time#Initialized, Time#set and Time#Minute (#2669) - Add Eastron SDM630 energy meter by Gennaro Tortone (#2735) - Add KNX communication enhancement by Adrian Scillato (#2742) - Add KNX energy data by Adrian Scillato (#2750) - Add rule support for IrReceive and RfReceive (#2758) - Add python script fw-server.py in tools folder to create a simple OTA server by Gennaro Tortone (#2759) - Add rule variables %time% for minutes since midnight, %uptime%, %sunrise% and %sunset% giving time in minutes (#2669) - Add rules %mem1% to %mem5% variable names storing data in flash (#2780) - Add rules test on %varx% or %memx% (#2780) - Add optional token %id% substituting the unique MAC address to fulltopic by Michael Graf (#2794) - Add support for Sonoff S26 Smart Socket (#2808) - Add command WebSend [(:,:)] (#2821) - Add increment and decrement value to command Counter (#2838) - Add support for Sonoff iFan02 as module 44 introducing command FanSpeed 0..3 (#2839) - Add source information to command execution to be shown with logging option 3 (#2843) - Add support for uploading Sonoff Bridge firmware found in tools/fw_efm8bb1 folder build by Portisch using Web Gui File Upload (#2886) - Add command RfRaw to control Portisch firmware features - Add support for I2C temperature sensor LM75AD (#2909) - Add option 0 to command Timers disarming all timers (#2962) - Add performance improvement when updating multiple individual WS2812 pixels (#3007) - Add command SetOption28 to switch between hex or decimal Sonoff Bridge RF received data format (#3008) - Add command SetOption29 to switch between hex or decimal IR received data format - Add decimal values support for commands ADD, SUB, MULT and SCALE (#3083, #3089) - Add support for bitflags SetOption50 .. SetOption81 (#3118) ### 5.14.0 20180515 - Update language files - Update TasmotaSerial to 2.0.0 allowing Hardware Serial Fallback when correct connections are configured - Change command handling - Change user_config(_override).h defines TIME_STD and TIME_DST - Change user_config(_override).h otaurl to http://sonoff.maddox.co.uk/tasmota/sonoff.bin (#2588, #2602) - Fix configuration restore regression from 5.13.1 - Fix compile error when ADC is enabled and Rules are disabled (#2608) - Fix rule power trigger when no backlog command is used (#2613) - Fix several timer data input and output errors (#2597, #2620) - Fix KNX config error (#2628) - Fix sensor MHZ-19 vanishing data over time (#2659) - Fix KNX reconnection issue (#2679) - Fix DST and STD time for Southern Hemisphere by Adrian Scillato (#2684, #2714) - Add Portuguese in Brazil language file - Add SetOption26 to enforce use of indexes even when only one relay is present (#1055) - Add support for sensor SI1145 UV Index / IR / Visible light (#2496) - Add rule state test for On/Off in addition to 0/1 (#2613) - Add hardware serial option to MHZ-19 sensor (#2659) - Add Eastron SDM120 energy meter by Gennaro Tortone (#2694) - Add user entry DST/STD using commands TimeStd and TimeDst (See wiki for parameter syntax) (#2721) ### 5.13.1 20180501 - Fix JSON buffers size too small for execution in some situations (#2580) - Fix configuration restore (#2591) - Add define MODULE for user selecting default model although it preferably should not be changed (#569, #2589) ### 5.13.0 20180430 - Change platformio option sonoff-ds18x20 to sonoff-allsensors enabling ds18x20 and all other sensors in one image - Change status display of Ssid and SetOption - Change default option SetOption15 from 0 to 1 providing better initial PWM experience - Change webpage parameter communication - Change max number of commands in Backlog from 15 to 30 and ignore commands overflowing - Change TSL2561 driver to joba library and delete Adafruit library (#1644) - Change default parameters in user_config.h to undefined for easy installation (#1851) - Change max user configurable hold time from 10 to 25 seconds (#1851) - Change Sonoff SC JSON format (#1939) - Change Polish language to using Diacritics (#2005) - Change user_config_override usage by providing user_config_override_sample.h (#2228) - Change MQTT response topic for Energy changes from ENERGY to SENSOR (#2229, #2251) - Change default Reset configuration time from 4 seconds to 40 seconds on Button hold (#2268) - Change ESP8266 Analog JSON message from {"Analog0:123"} to {"ANALOG":{"A0:123"}} to accomodate rules (#2560) - Change Counter JSON message from {"Counter1":0,"Counter3":0} to {"COUNTER":{"C1":0,"C3":0}} to accomodate rules - Change ADS1115 JSON message from {"ADS1115":{"Analog0":123,"Analog1":123}} to {"ADS1115":{"A0":123,"A1":123}} - Fix intermittent exception when dns lookup is used while sleep is enabled - Fix 5.4.0 regression turning off single press after button hold during 4x hold time - Fix possible wifi connection problem by erasing sdk configuration parameters - Fix NTP sync to Thu Jan 01 08:00:10 1970 results in uptime 17651+ days (core2.4.1/sdk2.2.1) - Fix MAX31850 higher temperatures (#1269) - Fix freeing more code space when emulation is disabled (#1592) - Fix providing web page configuratin option for Friendly Name when no device (relay or light) is configured (#1850) - Fix compile error when define HOME_ASSISTANT_DISCOVERY_ENABLE is not set (#1937) - Fix MQTT TLS fingerprint validation (#2033) - Fix update temperature on DS18x20 drivers (#2328) - Fix compile error when not defined USE_TIMERS (#2400) - Fix configuration filename truncation when it contains spaces (#2484, #2490) - Fix Energy Today and Yesterday overflow (#2543) - Add serial debug info - Add Portuguese language file - Add Czech language file - Add Bulgarian language file - Add Domoticz dust (custom) sensors to PMS5003 and NovaFitness SDS drivers as PM1, PM2.5 and PM10 - Add commands Publish, Rule, RuleTimer and Event. See Wiki about Rule restriction, usage and examples - Add sonoff-classic, sonoff-allsensors and sonoff-knx - Add some coloring to important web buttons - Add support for sensor HC-SR04 ultrasonic (#113, #1964, #2444) - Add define MQTT_TELE_RETAIN compile option default set to 0 (#1071) - Add 16 timers using commands Timer and Timers (#1091) - Add optional Timer configuration webpage to be enabled in user_config.h with define USE_TIMERS_WEB - Add Multichannel Gas sensor using MultiChannel_Gas_Sensor library (#1245) - Add Domoticz Battery and RSSI Quality (#1604) - Add command HSBColor Hue,Sat,Bri (#1642, #2203) - Add compile time support for WS2812 BRG and RBG led configurations to be defined in user_config.h (#1690) - Add optional usage of %d or %X suffices in MQTT client to append chipid (#1871) - Add optional usage of %d or %X suffices in MQTT topic to append chipid (#1871) - Add optional usage of %d or %04d in ota url to be replaced with chipid (#1871) - Add Sonoff Bridge command RfKey 5 to show current RF key values either default or learned (#1884) - Add user configurable serial GPIOs to MagicHome and Arilux modules (#1887) - Add Russian language file (#1909) - Add Webserver upload preflight request support (#1927) - Add Home Assistant clear other device (#1931) - Add Restart time to Status 1 (#1938) - Add optional TSL2561 driver using library Joba_Tsl2561 to be enabled in user_config.h with define USE_TSL2561_JOBA (#1951) - Add support for sensor SHTC3 (#1967) - Add compiler check for stable lwIP version v1.4 (#1940) - Add support for multiple SHT3X sensors (#1949, #2110) - Add always suffix with device number in Mqtt discovery topic (#1962) - Add support for optional MQTT drivers to be selected in user_config.h (#1992) - Add optional Arduino OTA support to be enabled in user_config.h (#1998) - Add diacritics to Polish language file (#2005) - Add Hungarian language file (#2024) - Add support for Nova Fitness SDS011 and possibly SDS021 particle concentration sensor (#2070) - Add single decimal precision to Nova Fitness SDS0x1 sensor values (#2093) - Add Chinese (Traditional) in Taiwan language file (#2108) - Add Sonoff SC domoticz support for Sound level as Counter and Air quality (#2118) - Add a second TLS fingerprint to allow switching keys in TLS mode (#2033, #2102) - Add display of remaining pulse time to command PulseTime (#2085) - Add additional time offset to Wifi Retry based on device mac address (#2089) - Add command Color6 RRGGBB for Clock hour marker color and command Rotation pixels for Clock rotation (#2092) - Add HTML language header in local language (#2123) - Add command PowerDelta 0..100 (percentage) to Energy monitoring devices to report on active power load change (#2157) - Add Restart Reason to Status 1 report (#2161) - Add command Channel 0..100 to control dimmer value for individual color channels (#2111, #2203) - Add support for Hardware Serial bridge using commands SerialDelimiter, Baudrate and SerialSend. Supports 8N1 and text only (#2182) - Add support for Software Serial bridge using commands SerialDelimiter, SBaudrate and SSerialSend. Supports 8N1 and text only (#2190) - Add support for Zengge WF017 PWM Led strip controller (#2202) - Add PWM status to command State if PWM enabled (#2203) - Add all FriendlyNames to Status information (#2208) - Add Channel status information (#2211) - Add hexadecimal Data entry to command IrSend using 0x notation (#1290, #2314) - Add Home Assistant MQTT Discovery for Buttons and change SetOption19 response (#2277) - Add multiple color entry support for command Led like Led2 120000 001200 000012 setting led2 as Red, Led3 as Green and Led4 as Blue (#2303) - Add hexadecimal RGB color entry on RGBCW leds (#2304) - Add support for SGP30 gas and air quality sensor (#2307) - Add optional Sunrise and Sunset timers with commands Latitide and Longitude to be enabled with define USE_SUNRISE in user_config.h (#2317) - Add timer sunrise and sunset offset (#2378) - Add user selectable defines for Sunrise/set Dawn option (#2378) - Add optional KNX IP Protocol Support (#2402) - Add random window to timers (#2447) - Add Greek language file (#2491) - Add support for Sonoff Pow R2 (#2340) - Add GPIO_User to GPIO02 for all Sonoff T1 (#2524) ### 5.12.0 20180209 - Change library PubSubClient.h define MQTT_MAX_PACKET_SIZE from 512 to 1000 for Home Assistant support - Change relation of define MESSZ being dependent on PubSubClient.h define MQTT_MAX_PACKET_SIZE - Change command color parameter input checks to less strict for Home Assistant support - Change command Ina219Mode into command Sensor13 - Change commands HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to be used for both Pow and S31 calibration - Change commands HlwPSet, HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used for both Pow and S31 calibration - Change uptime from hour to second resulting in a display of 123T13:45:21 where 123 is days - Change module name Wemos D1 mini into Generic (#1220) - Change HTML from width=100% to style=width:100% supporting HTML5 (#1358) - Change OSWATCH_RESET_TIME (Blocked loop) from 30 to 120 seconds to allow slow networks (#1556) - Change WIFI_MANAGER_SEC into WIFI_CONFIG_SEC (#1616) - Change function pointers code to save code space and memory (#1683) - Change webserver argument processing gaining 5k code space (#1705) - Change weblog memory usage (#1730, #1793, #1819) - Update TasmotaSerial library to 1.1.0 - Update language files Italian (#1594), Dutch (#1723) and Spanish (#1722) - Fix Non-English JSON temperature unit attachement - Fix Arilux RF induced exception by moving interrupt handler to iram on non ESP8266/Arduino lib v2.3.0 - Fix truncated command names and wrong response for DomoticzSwitchIdx (#1571) - Fix %-sign issue as printf escape character in Humidity and Sonoff SC (#1579) - Fix DS18B20 temperature JSON decimal dot (#1561) - Fix Energy JSON message (#1621) - Fix IRSend parameter translation (#1636) - Fix TSL2561 device detection (#1644, #1825) - Fix BME680 teleperiod resistance measuring (#1647) - Fix Energy Monitoring Energy Today and Energy Total reading after restart (#1648) - Fix IRReceive Data value (#1663) - Fix Energy Monitoring Energy Period roll-over (#1688) - Fix compiler warnings (#1774) - Fix command PWM response if no PWM channel is configured (#1783) - Add locale Decimal Separator to Web sensor page - Add ColorTemperature to light status message - Add command PowerOnState option 5 which inverts PulseTime and allows for delayed always on after power on - Add OtaMagic two step Web server OTA upgrade using filename-minimal image if OTA free space is too small - Add support for PMS5003 and PMS7003 particle concentration sensor - Add command SetOption21 1 to allow Energy Monitoring when power is off on Sonoff Pow and Sonoff S31 (#1420) - Add Chinese language file (#1551) - Add French language file (#1561) - Add Spanish language file (#1589) - Add HTTP Allow Cross Origin removed from ESP8266/Arduino lib v2.4.0 (#1572) - Add Home Assistant MQTT Discovery for switch and light to be enabled by command SetOption19 1 (#1534) or define HOME_ASSISTANT_DISCOVERY_ENABLE in user_config.h (#1685) - Add command State to retrieve device state information (same data as teleperiod state and status 11 in slightly different JSON format) - Add optional login to Webserver AP mode (#1587, #1635) - Add command Sensor15 2 to start MHZ19(B) Zero Point Calibration (#1643) - Add support for Sonoff S31 Smart Socket with Power Consumption Detection (#1626) - Add command SetOption20 to allow update of Dimmer/Color/Ct without turning power on (#1719, #1741) - Add NTP sync time slot based on chip id (#1773) - Add cursor pointer to web button (#1836) ### 5.11.1 20180107 - Fix Sonoff Pow command handling (#1542) ### 5.11.0 20180107 - Minor webpage HTML optimizations (#1358) - Updated German translation (#1438) - Change Sonoff Pow Energy MQTT data message and consolidate Status 8 into Status 10 - Change ADS1115 default voltage range from +/-2V to +/-6V (#1289) - Change text to Active for 3 minutes (#1364) - Change Wemo SetBinaryState to distinguish from GetBinaryState (#1357) - Change output of HTTP command to valid JSON and Array only (#1363) - Removed all MQTT, JSON and Command language defines from locale files and set fixed to English (#1473) - Renamed commands Color2,3,4 to Color3,4,5 - Fix BME280 calculation (#1051) - Fix Sonoff Bridge missed learned key if learned data contains 0x55 (End of Transmission) flag (#1095, #1294) - Fix PWM initialization in Dimmer/Color mode (#1321) - Fix Wemo Emulation (#1357) - Fix display of build date and time in non-english locale (#1465) - Fix Wemo and Hue emulation by adding M-Search response delay (#1486) - Add libraries Adafruit_BME680-1.0.5, Adafruit_Sensor-1.0.2.02, TasmotaSerial-1.0.0 and TSL2561-Arduino-Library - Add command Color2 to set color while keeping same dimmer value - Add device function pointers - Add support for SenseAir S8 CO2 sensor - Add color led signal to Carbon Dioxide (CO2) sensors using defines CO2_LOW and CO2_HIGH in user_config.h - Add support for Domoticz Air Quality sensor to be used by MH-Z19(B) and SenseAir sensors - Add support for PZEM004T energy sensor - Add support for iTead SI7021 temperature and humidity sensor by consolidating DHT22 into AM2301 and using former DHT22 as SI7021 (#735) - Add support for BME680 using adafruit libraries (#1212) - Add support for MH-Z19(B) CO2 sensor (#561, #1248) - Add multipress support and more user configurable GPIO to Sonoff Dual R2 (#1291) - Add support for TSL2561 using adafruit library (#661, #1311) - Add support for SHT3x (#1314) - Add support for Arilux LC06 (#1414) - Add Italian language file (#1449) - Add 2nd Gen Alexa support to Wemo emulation discovery (#1357, #1450) - Add define for additional number of WS2812 schemes (#1463) ### 5.10.0 20171201 - Upgrade library ArduinoJson to 5.11.2 - Upgrade library IRRemoteEsp8266 to 2.2.1 + 2 commits but disabled some protocols (code size reduction) - Upgrade library NeoPixelBus to 2.2.9 - Upgrade library OneWire to 2.3.3 + 6 commits and disabled CRC lookup-table (#define ONEWIRE_CRC8_TABLE 0) (code size reduction) - Update library PubSubClient to 2.6 + 9 commits and additional delay (#790) - Update core_esp8266_wiring_digital.c to latest (staged) level - Patch library I2Cdevlib-Core for esp8266-core 2.4.0-rc2 compatibility - Remove command EnergyReset 1..3 now replaced by EnergyReset1 to EnergyReset3 - Remove spaces in JSON messages (code size reduction) - Renamed xsns_05_ds18x20.ino to xsns_05_ds18x20_legacy.ino still using library OneWire and providing dynamic sensor scan - Fix possible iram1_0_seg compile error by shrinking ICACHE_RAM_ATTR code usage - Fix PWM watchdog timeout if Dimmer is set to 100 or Color set to 0xFF (#1146) - Fix Sonoff Bridge Learn Mode hang caused by unrecognised RF code (#1181) - Fix blank console log window by using XML character encoding (#1187) - Fix wrong response name for command HlwISet (#1214) - Fix DHT type sensor timeout recognition by distinguish "signal already there" from "timeout" (#1233) - Add fixed color options 1..12 to command Color - Add + (plus) and - (minus) to commands Dimmer (+10/-10), Speed and Scheme - Add + (plus) and - (minus) to command Color to select 1 out of 12 preset colors - Add + (plus) and - (minus) to command Ct to control ColdWarm led ColorTemperature (+34/-34) - Add commands EnergyReset1 0..42500, EnergyReset2 0..42500 and EnergyReset3 0..42500000 - to (Re)set Energy Today, Yesterday or Total respectively in Wh (#406, #685, #1202) - Add optional ADS1115 driver as alternative for unsupported I2Cdevlib in esp8266-core 2.4.0-rc2 - Add support for INA219 Voltage and Current sensor to be enabled in user_config.h with define USE_INA219 - Add support for Arilux LC11 (Clearing RF home code when selecting no Arilux module) - Add support for WS2812 RGBW ledstrips to be enabled in user_config.h with define USE_WS2812_CTYPE (#1156) - Add SettingsSaveAll routine to command SaveData to be used before controlled power down (#1202) - Add option PUSHBUTTON_TOGGLE (SwitchMode 7) to allow toggling on any switch change (#1221) - Add new xdrv_05_ds18x20.ino free from library OneWire and add the following features: - Add support for DS1822 - Add forced setting of 12-bit resolution for selected device types (#1222) - Add read temperature retry counter (#1215) - Fix lost sensors by performing sensor probe at restart only thereby removing dynamic sensor probe (#1215) - Fix sensor address sorting using ascending sort on sensor type followed by sensor address - Rewrite JSON resulting in shorter message allowing more sensors in default firmware image: - "DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6} - Add additional define in user_config.h to select either single sensor (defines disabled), new multi sensor (USE_DS18X20) or legacy multi sensor (USE_DS18X20_LEGACY) - Add clock support for more different pixel counts (#1226) - Add support for Sonoff Dual R2 (#1249) - Add FriendlyName to web page tab and add program information to web page footer (#1275) ### 5.9.1 20171107 - Add external sensor function pointer interface to enable easy sensor addition - Add support for ADS1115 to be enabled in user_config.h and needs libraries i2cdevlib-Core and i2cdevlib-ADS1115 (#338, #660) - Fix Backup Configuration file download failure by defining proper file size (#1115) - Fix Exception 26 and empty console screen after usage of command WakeupDuration (#1133) - Fix some changed iTead web links in README.md (#1137) ### 5.9.0 20171030 - Rewrite code (partly) using Google C++ Style Guide (https://google.github.io/styleguide/cppguide.html) - Rewrite code by using command lookup tables and javascript (client side) web page expansions - Change HTML/CSS to enable nicer form field entry - Change default PWM assignments for H801 RGB(CW) led controller to support optional Color/Dimmer control - GPIO04 (W2) from GPIO_PWM2 to GPIO_USER to be user configurable for GPIO_PWM5 (second White - Warm if W1 is Cold) - GPIO12 (Blue) GPIO_PWM3 no change - GPIO13 (Green) from GPIO_PWM4 to GPIO_PWM2 - GPIO14 (W1) from GPIO_PWM1 to GPIO_USER to be user configurable for GPIO_PWM4 (first White - Cold or Warm) - GPIO15 (Red) from GPIO_PWM5 to GPIO_PWM1 - Change default PWM assignments for MagicHome RGB(W) led controller to support optional Color/Dimmer control - GPIO05 (Green) from GPIO_PWM4 to GPIO_PWM2 - GPIO12 (Blue) from GPIO_PWM5 to GPIO_PWM3 - GPIO13 (White) GPIO_USER to be user configurable for GPIO_PWM4 (White - Cold or Warm) - GPIO14 (Red) from GPIO_PWM3 to GPIO_PWM1 - Change default PWM assignment for Witty Cloud to support optional Color/Dimmer control (#976) - GPIO12 (Green) from GPIO_PWM4 to GPIO_PWM2 - GPIO13 (Blue) from GPIO_PWM5 to GPIO_PWM3 - GPIO15 (Red) from GPIO_PWM3 to GPIO_PWM1 - Change when another module is selected now all GPIO user configuration is removed - Change command name IRRemote to IRSend (#956) - Remove Arduino IDE version too low warning as it interferes with platformio.ini platform = espressif8266_stage - Fix command FullTopic entry when using serial or console interface - Fix possible UDP syslog blocking - Fix minimum TelePeriod of 10 seconds set by web page - Fix command GPIOx JSON response (#897) - Fix inverted relay power on state (#909) - Fix compile error when DOMOTICZ_UPDATE_TIMER is not defined (#930) - Fix alignment of web page items in some browsers (#935) - Fix setting all saved power settings to Off when SetOption0 (SaveState) = 0 (#955) - Fix timezone range from -12/12 to -13/13 (#968) - Fix Southern Hemisphere TIME_STD/TIME_DST (#968) - Fix TLS MQTT SSL fingerprint test (#970, #808) - Fix virtual relay status message used with Color/Dimmer control (#989) - Fix command IRSend and IRHvac case sensitive parameter regression introduced with version 5.8.0 (#993) - Fix pressure calculation for some BMP versions regression introduced with version 5.8.0i (#974) - Fix Domoticz Dimmer set to same level not powering on (#945) - Fix Blocked Loop when erasing large flash using command reset 2 (#1002) - Fix relay power control when light power control is also configured as regression from 5.8.0 (#1016) - Fix Mqtt server mDNS lookup only when MqttHost name is empty (#1026) - Add debug information to MQTT subscribe - Add translations to I2Cscan - Add translation to BH1750 unit lx - Add light scheme options (Color cycle Up, Down, Random) and moving WS2812 schemes up by 3 - Add Domoticz counter sensor to IrReceive representing Received IR Protocol and Data - Add option 0 to MqttHost to allow empty Mqtt host name - Add support for Arilux AL-LC01 RGB Led controller (#370) - Add esp8266 de-blocking to PubSubClient library (#790) - Add Domoticz sensors for Voltage and Current (#903) - Add platformio OTA upload support (#928, #934) - Add warning to webpage when USE_MINIMAL is selected (#929) - Add smoother movement of hour hand in WS2812 led clock (#936) - Add support for Magic Home RGBW and some Arilux Led controllers (#940) - Add command SetOption15 0 (default) for command PWM control or SetOption15 1 for commands Color/Dimmer control to PWM RGB(CW) leds (#941) - Add Domoticz counter sensor to Sonoff Bridge representing Received RF code (#943) - Add support for Luani HVIO board (https://luani.de/projekte/esp8266-hvio/) (#953) - Add PWM initialization after restart (#955) - Add IR Receiver support. Disable in user_config.h (#956) - Add support for inverted PWM (#960) - Add Sea level pressure calculation and Provide command Altitude (#974) - Add support for up to 8 relays (#995) - Add commands RfSync, RfLow, RfHigh, RfHost and RfCode to allow sending custom RF codes (#1001) - Add retain to ENERGY messages controlled by command SensorRetain (#1013) - Add commands Color2, Color3, Color4, Width2, Width3, Width4 and SetOption16 to set Ws2812 Clock parameters (#1019) - Add German language file (#1022) - Add support for connecting to MQTT brokers without userid and/or password (#1023) - Add support for esp8266 core v2.4.0-rc2 (#1024) - Add commands PwmRange 1,255..1023 and PwmFrequency 1,100..4000 (#1025) - Add Polish language file (#1044, #1047) - Add support for KMC 70011 Power Monitoring Smart Plug (#1045) - Add support for VEML6070 I2C Ultra Violet level sensor (#1053) - Add light turn Off Fade (#925) - Add IrSend command option Panasonic as IrSend {"Protocol":"Panasonic", "Bits":16388, "Data":\} - where 16388 is 0x4004 hexadecimal (#1014) - Add retry counter to DHT11/21/22 sensors (#1082) ### 5.8.0 20170918 - Remove the need for NeoPixelBus library for Hue support - Consolidate WS2812 into Sonoff Led for flexible future led strip library changes - Invert WS2812 fade speed to align with Sonoff led (Speed 1 = fast, Speed 8 = slow) - Remove upper case MQTT receive buffer - Reduce code and string length for output of commands Modules and GPIOs - Add Sonoff SC debug information - Change syslog service - Removed webserver syslog disable as now no longer needed - Increased default MQTT message size from 368 to 405 bytes while keeping MQTT_MAX_PACKET_SIZE = 512 (because we can) - Fix MQTT Offline or Remove MQTT retained topic code - Fix Domoticz loop when Emulation is selected - Add blink to WS2812 and Sonoff Led (#643) - Add option WIFI_WAIT (5) to command WifiConfig to allow connection retry to same AP without restart or update flash (#772, #869) - Add support for Witty Cloud (#794) - Add GPIO14 to Sonoff Dual (#797, #839) - Add support for Yunshan Wifi Relay (#802) - Add GPIO16 input pulldown (#827) - Add timeout to DHT and DS18B20 sensors (#852) - Fix watchdog timeout caused by lack of stack space by moving to heap (#853) - Allow LogPort and MqttPort up to 65535 and add LogPort tot Status 3 (#859) - Allow command SwitchTopic in group mode (#861) - Allow command SwitchMode if no switches are defined (#861) - Add optional dimmer parameter to command Wakeup for WS2812, AiLight, Sonoff B1, Led and BN-SZ01 (#867) - Fix basic On, Off, Toggle, Blink and BlinkOff commands when other language is selected (#874) ### 5.7.1 20170909 - Remove leading spaces from MQTT data - Fix webconsole special character entry - Allow # as prefix for color value - Fix Alexa detection and Hue App Update Request (#698, #854) ### 5.7.0 20170907 - Shrink module configuration webpage - Fix settings order during startup to allow for displaying debug messages - Fix some string length issues - Add more string length tests by using strncpy - Add Ai-Thinker RGBW led (AiLight) - Add Power check and add PulseTime to power check at startup (#526) - Add Supla Espablo support (#755) - Add more precision to Sonoff Pow period and power results using command WattRes 0|1 (#759) - Add basic internationalization and localization (#763) - Add more Sonoff Pow range checking (#772) - Fix invalid JSON (#786, #822) - Add duplicate check to received RF signal within 2 seconds for Sonoff Bridge (#810) ### 5.6.1 20170818 - Change module list order in webpage - Fix Sonoff T1 1CH and 2CH configuration (#751) ### 5.6.0 20170818 - Fix Sonoff Pow intermittent exception 0 - Change Sonoff Pow sending Domoticz telemetry data only - Add Ai-Thinker RGBW led (AiLight) (experimental) - Add NeoPixelBus library to Sonoff Led for Hue support - Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge - Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676) - Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color Temperature - Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1 - Add CT parameter to Hue - Add Sonoff T1 support (#582) - Add AnalogInput0 if configured as Analog Input to webpage (#697, #746) - Add command SetOption14 0|1 to enable interlock mode (#719, #721) - Fix Mitsubishi HVAC IR power controll (#740) ### 5.5.2 20170808 - Extent max number of WS2812 pixels from 256 to 512 (#667) - Add OTA handling if server responds with no update available (#695) - Removed undocumented command FlashMode (#696) - Fix compile time error message due to increased message buffer size (#703) ### 5.5.1 20170805 - Fix Sonoff Rf Bridge issues - Add Sonoff RF Bridge MQTT messages on received and learned RF signal - Add command VoltRes 0|1 to select voltage resolution to 0.1 V (#654) - Add averaging to Analog input (#686) - Add Energy tele data on Sonoff Pow Threshold change (#688) - Fix inconsistent property names in Messages (#690) ### 5.5.0 20170730 - Reduce code space by removing the following commands as they are replaced by SetOption alternatives: - SaveState = SetOption0 - ButtonRestrict = SetOption1 - Units = SetOption2 - MQTT = SetOption3 - MQTTResponse = SetOption4 - TempUnit = SetOption8 - Smoothing WS2812 animation poll, invert fade speed and max allowed wakeup time down to 3000 seconds - Fix initial button press detection - Add support for Sonoff RF Bridge 433 using command RfKey - Fix regression from 5.0.7 by increasing message buffer size from 360 to 368 to accomodate 4 x DS18x20 sensors (#637) - Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to send either ON/OFF or TOGGLE (#642) - Adjust HLW calibration limits to accomodate HuaFan device and add commands HlwPSet, HlwUSet and HlwISet (#654) ### 5.4.0 20170725 - Fix command reset regression introduced in 5.2.0 - Increase polling from 0.1 second to 0.05 second - Add multipress to all buttons - Fix button 1 double press behaviour on multi relay devices - Add support for Hua Fan Smart Socket (#479) - Add support for Sonoff 4ch Pro (#565) - Add command SetOption13 1 to allow immediate action on single button press - (disables multipress, hold and unrestricted commands) (#587) ### 5.3.0 20170715 - Major Hue rewrite which might introduce Alexa problems. If so, initiate an issue - Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control to Hue - Fix Sonoff Led Power, Dimmer and Color MQTT response (#176) - Add commands Delay and Backlog to allow multiple commands at once separated by ";" (#593) - Use default flashmode DOUT to solve restart hangs on esp8285 chips (#453, #598) - Change Web console column width from 99 to 300 (#599) ### 5.2.4 20170703 - Removed flash mode update after selecting different module solving esp8285 related problems - Add device type flag to sonoff_template.ino - Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led (#567) ### 5.2.3 20170630 - Change Sonoff Led color conversion code - Fix SetOption12 handling - Simplify auto configuration upgrade - Add option Upgrade \ to only upgrade to any higher version (Old PR #213) - Change FallbackTopic to cmnd/\/\ \ bypassing FullTopic and Prefix (#538) ### 5.2.2 20170625 - Add configuration SaveAddress to Status 1 and Information Page - Change Sonoff Led Color conversion from AtoH to strtol - Fix possible wrong uploads due to configuration overwrites (#542) - Fix payload negative numbers (#547) ### 5.2.1 20170622 - Fix Restore Configuration in case of lower version - Revert auto configuration upgrade allowing easy upgrade which was removed in version 5.2.0 - Fix config auto upgrade from versions below version 4.1.1 (#530) ### 5.2.0 20170619 - Add command SetOption12 1 to disable newly released configuration flash rotate to reduce flash wear - Fix command CounterDebounce by removing test for active GPIO (#524) - Add command SetOption33 1..250 to allow user configure POW Max_Power_Retry count (#525) ### 5.1.7 20170616 - Prep removal of SetOptions alternatives - Restore webpage upgrade error messages removed in 5.1.5 - Add hold button functionality to buttons 2 to 4 - Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds to 10 seconds (#200) - Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507) - Changed webpage form actions from post to get and use relative path url (#434, #522) ### 5.1.6 20170606 - Shrink code - Removed online configuration of Domoticz In and Domoticz Out MQTT strings - Removed commands DomoticzInTopic and DomoticzOutTopic - Add define KEY_HOLD_TIME to configure button hold threshold before sending MQTT Hold message - Add command StateText4 to configure button MQTT Hold text (= MQTT_CMND_HOLD) - Add command SetOption11 0|1 to swap pushbutton single and double press functionality (#200) - Add command SwitchMode 5 (PUSHBUTTONHOLD) and 6 (PUSHBUTTONHOLD_INV) (#489) ### 5.1.5 20170604 - Shrink code in preparation to ESP8266-Arduino 2.4.0-rc1 - Add effect parameter to HUE Device (#464) ### 5.1.4 20170601 - Removed pre-compiled versions from repository as they are available within the release - Changed HUE Device type to color supporting version (#464) - Fix compile error when BE_MINIMAL is selected (#467, #476) - Add multiple compiled versions to release using updated Travis script and platformio.ini (#467) ### 5.1.3 20170520 - Add Domoticz Counter ### 5.1.2 20170519 - Fix Counter/Timer JSON message and update Counter/Timer on webpage - Fix WS2812 Domoticz related regression issues ### 5.1.1 20170517 - Allow command FullTopic in group mode - Prepare for more use of RTC memory - Add independant WS2812 led string power control (#386, #390) - Add command Counter to control up to four GPIO falling edge interrupt counters or timers (#459) - Add command CounterType to select between pulse counting or pulse timing - Add command CounterDebounce to select global counter debounce time in mSec ### 5.1.0 20170513 - Fix Offline/Removal of retained topic when FullTopic is changed - Add FullTopic to MQTT Configuration and Information web pages - Add license model GPLv3 (#188) ### 5.0.7 20170511 - Fix possible exception 28 on empty command - Add command SetOption0 as replacement for SaveState - Add command SetOption1 as replacement for ButtonRestrict - Add command SetOption2 as replacement for Units - Add command SetOption4 as replacement for MqttResponse - Add command SetOption8 as replacement for TempUnit - Add command SetOption10 On|Off to select between Offline or Removing previous retained topic (#417, #436) ### 5.0.6 20170510 - Remove hyphen in case of a single DHT sensor connected (#427) - Add command MqttRetry to change default MQTT reconnect retry timer from minimal 10 seconds (#429) ### 5.0.5 20170508 - Add command FullTopic with tokens %topic% (replaced by command Topic value) and - %prefix% (replaced by command Prefix values) for more flexible topic definitions (#244) - See wiki > MQTT Features https://github.com/arendst/Tasmota/wiki/MQTT-Features for more information ### 5.0.4 20170505 - Add Sonoff Pow Energy Total up to 40 MWh - Add command EnergyReset 1|2|3 to reset Energy counters (#406) - Fix Domoticz Energy logging (#411) - Add command PowerOnState 4 to keep relay always on and disabling all power control (#418) ### 5.0.3 20170504 - Add command SensorRetain on|off to enable retaining of mqtt message tele/sonoff/SENSOR (#74) - Change WifiConfig timeout from 60 seconds to 180 seconds (#212) - Change Sonoff Touch command Ledstate functionality by turning led on if power is off (#214) - Add 4 seconds delay after power on before enabling button to workaround Wemos D1 mini RTS circuit (#380) ### 5.0.2 20170503 - Reset SaveData, SaveState and MqttResponse to default values due to rearranging settings - Moved some settings to flag area - Add command TempUnit Celsius|Fahrenheit for selecting Celsius or Fahrenheit (#347) - Add command TempRes 0..3 for selecting Temperature Resolution (#347) - Add command HumRes 0..3 for selecting Humidity Resolution (#347) - Add command PressRes 0..3 for selecting Pressure Resolution (#347) - Add command EnergyRes 0..5 for selecting Energy Resolution (#347) - Add "TempUnit":"C|F" to sensor JSON output (#347) - Add support for up to three DHT type sensors each using a different GPIO (#339, #404) ### 5.0.1 20170429 - Adjust Sonoff SC messages to prepare for display feature - Move static data from RAM to Flash - Fix PowerOnState for some devices not reporting "Power on" state (#284, #380, #383) ### 5.0.0 20170425 - Memory status message update - Fix setting migration to better preserve settings during move (#382) - Best practice is first doing a Backup Configuration before installing version 5.0.0 - Reset save count after setting move - Start using new linker script without SPIFFS ### 4.2.0 20170424 - Prepare for SPIFFS removal by moving settings to EEPROM area - Fix compilation error when webserver is disabled (#378) ### 4.1.3 20170410 - Add user configuarble GPIO to module S20 Socket and Slampher - Add support for Sonoff SC (#112) - Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led firmware (#122) - Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions due to power supply instabilities (#122) - Add Access Point Mac Address to Status 11 and Telemetry (#329) - Fix DS18B20 negative temperature readings (#334) ### 4.1.2 20170403 - Rename Unrecognised command to Unknown command - Remove all command lists - Remove command SmartConfig (superseded by WifiConfig) - Fix boot loop when selecting module Sonoff 4CH or Sonoff Touch on non ESP8285 hardware - Add optional support for Toshiba and Mitsubishi HVAC IR control (needs updated IRremote8266 library) (#83, #257) - Add all configured switches to Domoticz Configuration web page (#305) - Fix compile error when selecting WS2812 DMA (#313) ### 4.1.1 20170329 - Fix default Telemetry for command Prefix3 - Fix webserver Module parameters for disabled select - Fix sensor status for enabled switches - Remove Light as alternative for Power (save code space) - Remove migration option from pre V3 (code cleanup) - Remove unofficial SPIFFS support (code cleanup) - Remove command list when unknown command is entered (save code space) - Rename Status11 json from StatusPWR to unique StatusSTS - Rename command Gateway to IPAddres2, Subnetmask to IPAddress3 and DnsServer to IPAddress4 (save code space) - Add Command MqttResponse to select either command or RESULT topic as response (#258) - Add command StateText1 to StateText3 to assign MQTT_STATUS_OFF, MQTT_STATUS_ON and MQTT_CMND_TOGGLE respectively (#286) - Remove restart after IPAddress changes (#292) - Add support for MAX31850 in xsns_ds18x20.ino (#295) - Fix possible uptime update misses (#302) ### 4.1.0 20170325 - Change static IP addresses in user_config.h from list (using commas) to string (using dots) - Unify display result of commands Modules, Module and Gpios - Rewrite Module selection web page to bring size down from 18651 to 4319 bytes (!) (#234, #240) - Add basic support for (Lixada) H801 RGBWW controller (#252) - Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and PUB_PREFIX2 respectively (#255) - Add static ip addresses to flash (#262) - Add commands IpAddress, Gateway, Subnetmask and DnsServer to select static ip addresses (#273) ### 4.0.8 20170321 - Fix entering non-numeric webpassword - Force selection between TLS or Webserver due to memory restraint (#240) - Allow entering empty string using "0" for selected commands (#242) - Fix exception when posting commands to web console containing % (#250) ### 4.0.7 20170319 - Increased Sonoff Led PWM frequency from 432 to 1000 - Fix possible watch dog reboot after changing module type on web page - Fix reporting of GPIO usage from web page - Fix Sonoff Led blank during firmware upgrade - Fix Sonoff Led flicker and possible flash corruption by using latest Arduino-esp8266 versions of pwm core files included in sonoff library (#211) - Add PWM output control with commands PWM1 to PWM5 using user selectable GPIOs (#211) - Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal (1000) and HlwICal (2500) (#223) - Add Switch state to sensor status (#227, #233) - Add user configuarble GPIO to module Sonoff Touch (#228) - Add define WEB_PORT to user_config.h to change default web server port from 80 (#232) - Fix failed Ota Firmware upgrade started from Web page (#235) ### 4.0.6 20170316 - Fix to better find device by Wifi hostname - Fix compile error when some I2C devices are disabled - Add (experimental) support for SHT1X emulating I2C (#97) - Add ADC to ElectroDragon (#203) - Add support for Sonoff Dev (#206) ### 4.0.5 20170314 - Add command Status 11 to show power status with Vcc if define USE_ADC_VCC is enabled (default) - Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with define USE_ADC_VCC disabled (#137) - Add MQTT host:port to timeout message (#199) ### 4.0.4 20170312 - Add pulse timers for up to 4 relays (#106) - Fix Sonoff Led power state when dimmer or color is 0 (#176) - Add command NtpServer to configure up to three NTP servers (#177) - Delete module User Test as module Wemos D1 mini has same/more user configurable GPIO (#178) - Add more user configurable GPIO to module ElectroDragon (#183) ### 4.0.3 20170309 - Renamed Module NodeMCU to WeMos D1 mini - Add GPIO1 as user option to some modules - Add Buttons, Relays and Leds to user configurable options (#159) - Add description on Module parameters web page to some well known GPIOs (#107, #171) ### 4.0.2 20170308 - Restore correct seriallog level after Serial logging was disabled - Add simple dimmer slider to Sonoff Led web page - Reduced root webpage size by 31% - Expand Status 2 with Build date/time and core version - Fix webserver redirection when not in WifiManager mode (#156) - Add command ButtonRestrict On/Off to restrict access to button hold and button multi press options above 2 (#161) - Fix DS18S20 negative temperature readings (#165) - Fix crlf compilation error due to bad syntax (#144, #167) ### 4.0.1 20170305 - Fix char default sizes and set MESSZ to 360 (#143) - Fix SerialLog setting status - Disable syslog when emulation is active - Add DS18B20 web page display refresh ### 4.0.0 20170303 - Add define to remove config migration code for versions below 3.0 (See Wiki-Upgrade-Migration path) - Free memory by switching from String to char[] - Raised Sonoff Led PWM frequency from 200Hz to 432Hz in search of stability (hardware watchdog timeouts) (#122) - Increase message size and suggested minimum MQTT_MAX_PACKET_SIZE to 512 (#114, #124) - Remove runtime warning message regarding MQTT_MAX_PACKET_SIZE too small as it is now moved to compile time (#124) - Fix possible panics with web console and http commands while UDP syslog is active (#127) - Add optional static IP address (#129) - Add define ENERGY_RESOLUTION in user_config.h to allow user control over precision (#136) ### 3.9.22 20170228 - Update web console - Fix Status 4 JSON message - Add Exception info during restart if available - Add osWatch service to detect loop hangs that might happen during (OTA) upgrades - Add WiOn support for relay and switch only (#82, #102) - Allow for user specified relay count up to four in sonoff_template.h (#109) - Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021 (#118) - Add NodeMCU or Wemos configuration option (#119) ### 3.9.21 20170224 - Add ajax to web root page and web console (#79) - Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84, #88) - Fix MQTT upgrade when webserver is active ### 3.9.20 20170221 - Add minimal basic authentication to Web Admin mode (#87) - Fix Hue and add HSB support (#89) ### 3.9.19 20170219 - Sonoff Led: Made GPIO04, 05 and 15 available for user - Sonoff Led: Add commands Fade, Speed, WakupDuration, Wakeup and LedTable ### 3.9.18 20170218 - Fix ledstate 0 to turn off led - Fix Sonoff Led dimmer range (#16) - Change Sonoff Led command Dimmer to act on both cold and warm color - Add Sonoff Led command Color CCWW where CCWW are hexadecimal values fro 00 - FF - Reduce Sonoff Led flickering by disabling interrupts during flash save and disabling - Led during OTA upgrade and Web upload (#16) ### 3.9.17 20170217 - Fix possible ArduinoJSON related memory fragmentation - Changed console logging using less memory - Add GPIO04 as user selectable for Sonoff Dual (#75) ### 3.9.16 20170214 - Update latching relay handler - Add support for IR led using IRremoteESP8266 library (#59) - Add Hue argument passing using ArduinoJSON library (#59) ### 3.9.15 20170213 - Change JSON float values from string to number according to http://json.org (#56) - Add support for exs latched relay module https://ex-store.de/ESP8266-WiFi-Relay-V31 (#58) - Add support for inverted relays - Changed MAX_LOG_LINES from 70 to 60 to preserve memory ### 3.9.14 20170211 - Add False and True as alternatives for 0/Off and 1/On (#49) - Fix Status10 JSON format (#52) - Fix DS18x20 using OneWire library (#53) ### 3.9.13 20170210 - Add FlashChipMode to Status 4 - Removed redundant DHT2 option and code - Add Sonoff SV GPIO pin 05 configuration (#40) - Add configuration file backup and restore via web page - Fix latency due to light_sleep mode even if sleep was set to zero (#50) ### 3.9.12 20170208 - Fix compile error when webserver is disabled (#30) - Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during OTA upload - Fix hostname issues by not allowing user entry of string formatting and removing from user_config.h (#36) ### 3.9.11 20170204 - Fix command I2Cscan - Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic - Make all TELEMETRY, STATUS and COMMAND message topics unique (#4) - Advertise command topic to be used by iobroker (#299) - Fix butten (non)detection if no GPIO_KEY1 is defined (#13) - Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars (#18) - Update web page with Build Date/Time, Emulation and mDNS Discovery and Advertise information (#21) ### 3.9.10 20170130 - Add WS2812 Color Type selection (RGB or GRB) to user_config.h (#7) - Hue api changes to support HUE App(s) (#8) ### 3.9.9 20170130 - Add command status 10 showing sensor data - Fix hlw status messages if hlw is disabled ### 3.9.8 20170130 - Remove GPIO07 and GPIO08 from user selectable (#5) ### 3.9.7 20170129 - Fix possible WS2812 exceptions when using emulation - Add command Emulation to dynamic configure Belkin WeMo and Hue Bridge for Alexa ### 3.9.6 20170129 - Add dynamic sleep for WS2812 animation (#1) ### 3.9.5 20170128 - Fix error message in case of wrong Domoticz command ### 3.9.4 20170127 - Fix Sonoff Dual Relay switching (#287) ### 3.9.3 20170127 - Add confirmation before Restart via webpage - Expand Domoticz Configuration webpage with Key, Switch and Sensor Index and - add commands DomoticzSwitchIdx and DomoticzSensorIdx (#86) (#174) (#219) - Fix default DHT11 sensor driver selection - Fix LedPower status after button press (#279) - Add command Sleep 0 - 250 mSec for optional light sleep mode to lower energy consumption (#272) - (Expect overall button/key/switch misses and wrong values on Sonoff Pow) - Add Hue brightness extension (#281) - Fix Hue brightness and change to call by reference (#283) ### 3.9.2 20170124 - Add confirmation before Reset Configuration via webpage (#244) - Add WS2812 features (see Wiki commands) ### 3.9.1 20170124 - Change PowerOnState function to only trigger when Power On (and not just restart) (#238) - Move HLW interrupts back to RAM and make WS2812_DMA optional as it generates Exception on Pow (#264) - Add charset=utf-8 to webpages (#266) - Update Hue emulation (#268) - Fix status module number - Add support for domoticz Dimmer on Sonoff_Led and WS2812 - Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during web upload ### 3.2.6a 20170120 - Fix Sonoff Pow compile error (#255) - Move HLW interrupts back to ROM (Needed for WS2812 DMA interrupts) - Removed all IO config from user_config.h as this will be done by commands or webpage - Removed MessageFormat and supports JSON only except POWER/LIGHT status - Add command LedPower to control main led (#247) - Add more FriendlyNames for Hue (#254) - Add DMA support for WS2812 when using pin 3 while other pins work just as well in my case... - Add HUE emulation for Alexa (#229) - Add basic WS2812 support (#229) - Fix Wemo when MQTT is disabled (#245) - Revert ButtonTopic and change SwitchTopic1 - 4 to one SwitchTopic - Rename MqttUnits to Units - Add Mqtt command to enable/disable MQTT ### 3.2.2a 20170115 - Add dynamic (Sonoff) Module, user GPIO and sensor selection (one size fits (almost) all) - Add support for Sonoff LED - Add Seriallog disable after 600 seconds for Sonoff Dual and 4 Channel - Add ButtonTopic2 - 4, SwitchTopic1 - 4 and SwitchRetain ### 3.2.2 20170113 - Fix PowerOnState 2 functionality after re-applying power (#230) ### 3.2.1 20170113 - Fix some failed command decoding (#228) - Removed passwords from status messages (#216) ### 3.2.0 20170111 - Add I2C BH1750 sensor (#222) - Sensor rewrite preparing for online selection ### 3.1.16 20170109 - Fix Domoticz possible error condition - Remove Wifi password from connection message (#216) - Add Configure Other menu item to web page (#209) - Add command FriendlyName, field Friendly Name and define FRIENDLY_NAME to be used by Alexa - eliminating current use of MQTT_CLIENT_ID (#209) - Add friendlyname to webpage replacing former hostname ### 3.1.15 20170108 - Fix Domoticz send key regression with Toggle command ### 3.1.14 20170107 - Add support for command TOGGLE (define MQTT_CMND_TOGGLE) when ButtonTopic is in use and not equal to Topic (#207) ### 3.1.13 20170107 - Fix web console command input when SUB_PREFIX contains '/' (#152) - Add command response to web command (#200) - Add option to disable MQTT as define USE_MQTT in user_config.h (#200) ### 3.1.12 20170106 - Add OTA retry to solve possible HTTP transient errors (#204) - Fix MQTT host discovery ### 3.1.11 20170105 - Add mDNS to advertise webserver as .local/ ### 3.1.10 20170105 - Fix ButtonTopic when SUB_PREFIX = PUB_PREFIX - Add workaround for possible MQTT queueing when SUB_PREFIX = PUB_PREFIX - Add optional MQTT host discovery using define USE_DISCOVERY in user_config.h (#115) ### 3.1.9 20170104 - Fix Power Blink start position (toggled) - Change PulseTime increments: 1 .. 111 in 0.1 sec (max 11 seconds) and 112 .. 64900 in seconds (= 12 seconds until 18 hours) (#188) - Add support for SUB_PREFIX = PUB_PREFIX (#190) ### 3.1.8 20170103 - Add retain flag to LWT offline and only send "tele/sonoff/LWT Offline" (#179) - Change retained LWT Online message to only send "tele/sonoff/LWT Online" ### 3.1.7 20161231 - Add retained message LWT Online when sonoff makes MQTT connection (#179) ### 3.1.6 20161230 - Add blinking using commands BlinkTime, BlinkCount and Power Blink|3|BlinkOff|4 (#165) ### 3.1.5 20161228 - Fix serial space command exception (28) ### 3.1.4 20161227 - Fix MQTT subscribe regression exception (3) (#162) - Fix serial empty command exception (28) ### 3.1.3 20161225 - Extent Domoticz configuration webpage with optional indices (#153) - Fix multi relay legacy tele message from tele/sonoff/2/POWER to tele/sonoff/POWER2 - Add support for iTead Motor Clockwise/Anticlockwise ### 3.1.2 20161224 - Extent command PowerOnState with toggle at power on (option 2 is now option 3!) (#156) ### 3.1.1 20161223 - Add support for Sonoff Touch and Sonoff 4CH (#40) - Update DomoticzIdx and DomoticzKeyIdx with relay/key index (DomoticzIdx1/DomoticzKeyIdx1) - Add command PowerOnState to control relay(s) at power on (#154) ### 3.1.0 20161221 - Add Sonoff Pow measurement smoothing - Fix serial command topic preamble error (#151) - Fix 2.x to 3.x migration inconsistencies (#146) ### 3.0.9 20161218 - Add Sonoff Pow voltage reading when relay is on but no load present (#123) ### 3.0.8 20161218 - Add temperature conversion to Fahrenheit as option in user_config.h (TEMP_CONVERSION) (#145) ### 3.0.7 20161217 - Add user_config_override.h to be used by user to override some defaults in user_config.h (#58) - Fix Sonoff Pow low power (down to 4W) intermittent measurements (#123) ### 3.0.6 20161217 - Fix MQTT_CLIENT_ID starting with % sign as in "%06X" (#142) - Add auto power off after PulseTime### 0.1 Sec to relay 1 (#134) ### 3.0.5 20161215 - Add more control over LED with command LedState options (#136, #143) - LED_OFF (0), LED_POWER (1), LED_MQTTSUB (2), LED_POWER_MQTTSUB (3), LED_MQTTPUB (4), LED_POWER_MQTTPUB (5), LED_MQTT (6), LED_POWER_MQTT (7) - Add option WIFI_RETRY (4) to command WifiConfig to allow connection retry to other AP without restart (#73) ### 3.0.4 20161211 - Fix intermittent Domoticz update misses (#133) ### 3.0.3 20161210 - Fix compiler warnings (#132) - Remove redundant code - Fix Domoticz pushbutton support ### 3.0.2 20161209 - Add pushbutton to SwitchMode (#130) ### 3.0.1 20161209 - Fix initial config ### 3.0.0 20161208 - Migrate and clean-up flash layout - Settings from version 2.x are saved but settings from version 3.x can not be used with version 2.x - Change SEND_TELEMETRY_RSSI to SEND_TELEMETRY_WIFI and add AP and SSID to telemetry - Split long JSON messages - Fix inconsistent status messages - Fix all status messages to return JSON if enabled - Remove relay index in cmnd/sonoff//POWER now changed - to cmnd/sonoff/POWER for single relay units - and cmnd/sonoff/POWER for multi relay units like Sonoff dual - Add retain option to Power/Light status controlled by command PowerRetain On|Off (#126) ### 2.1.2 20161204 - Add support for second wifi AP (#73) - Update command WifiConfig - Fix possible WifiManager hang ### 2.1.1a 20161203 - Fix scan for wifi networks if WeMo is enabled - Fix syslog setting using web page ### 2.1.1 20161202 - Add support for ElectroDragon second relay and button (only toggle with optional ButtonTopic) (#110) ### 2.1.0 20161202 - Add optional EXPERIMENTAL TLS to MQTT (#49) - Fix MQTT payload handling (#111) - Optimzed WeMo code ### 2.0.21a 20161201 - Fix WeMo PowerPlug emulation ### 2.0.21 20161130 - Add Belkin WeMo PowerPlug emulation enabled with USE_WEMO_EMULATION in user_config.h (Heiko Krupp) (#105, #109) ### 2.0.20 20161130 - Relax MQTTClient naming but only allows hexadecimal uppercase numbers (#107) - Add I2C support with command I2CScan - Add I2C sensor driver for HTU21 as alternate sensor using TH10/16 connectors (Heiko Krupp) (#105) - Add I2C sensor driver for BMP085/BMP180/BMP280/BME280 as alternate sensor using TH10/16 connectors ### 2.0.19a 20161127 - Add support for ButtonTopic and ButtonRetain to wall switch function - Add pullup to SWITCH_PIN and command SwitchMode to syntax ### 2.0.18 20161126 - Add SUB_PREFIX multi level support allowing 'cmnd' or 'cmnd/level2/level3' - Add wall switch function to GPIO14 and command SwitchMode (Alex Scott) (#103) ### 2.0.17 20161123 - Calibrate HLWPCAL from 12345 to 12530 - Add alternative sensor driver DHT2 using Adafruit DHT library - Add define MESSAGE_FORMAT to user_config.h - Throttle console messages - Shorten JSON messages - Fix possible Panic - Fix User mode webserver security ### 2.0.16 20161118 - Add alternative sensor driver DS18x20 using OneWire library (#95) - Change sensor MQTT message from tele/sonoff/TEMPERATURE to tele/sonoff/DHT/TEMPERATURE or - tele/sonoff/DS18B20/TEMPERATURE or tele/sonoff/DS18x20/1/TEMPERATURE - Add sensors to root webpage and auto refresh every 4 seconds (#92) - Add optional JSON messageformat to all telemetry data - Enforce minimum TelePeriod to be 10 seconds - Fix Energy Yesterday reset after restart - Add Energy Today restore after controlled restart ### 2.0.15 20161116 - Change TODAY_POWER and PERIOD_POWER to TODAY_ENERGY and PERIOD_ENERGY - Fix serial regression - Fix syslog hangs when loghost is unavailable ### 2.0.14 20161115 - Add HLW threshold delay - Fix HLW intermittent current deviation - Fix button functionality during wificonfig - Add CRC check to DS18B20 sensor (#88) ### 2.0.13 20161113 - Add additional upload error code descriptions - Add PlatformIO support (#80) ### 2.0.12 20161113 - Fix Serial and Web response regression when no MQTT connection available - Fix Sonoff Dual power telemetric data for second relay - Removed MQTT password from Information web page - Hide MQTT password from Configure MQTT web page ### 2.0.11 20161111 - Rewrite button and web toggle code - Fix NTP sync - Add HLW calibration commands HLWPCAL, HLWUCAL and HLWICAL (need define USE_POWERCALIBRATION) - Fix power threshold tests ### 2.0.10 20161109 - Add additional Domoticz define (#63) - Add defines MQTT_STATUS_ON and MQTT_STATUS_OFF in user_config.h to select status On/Off string - Fix status response differences (#65) - Fix divide by zero exception (#70) - Fix syslog loop exception ### 2.0.9 20161108 - clarify MODULE in user_config.h - Fix hlw false values ### 2.0.8 20161108 - Add initial status after power on - Seperate driver files - Fix hlw code and calibrate Pow - Move user config defines to user_config.h (#61) ### 2.0.7 20161030 - Make Ticker mandatory - Add Domoticz support (Increase MQTT_MAX_PACKET_SIZE to 400) (#54) - Add command MessageFormat 0|1 to select either legacy or JSON output ### 2.0.6 20161024 - Add Sonoff Pow power factor - Initial support for up to four relays using iTEAD PSB (4Channel) - - Currently only supports one button (All buttons behave the same) - - Use command MODEL 4 to select four relay option - (After first power on it will support 2 relays like Sonoff Dual) - Fix ledstate - Add command Status 9 to display Sonoff Pow thresholds - Add commands PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow and CurrentHigh for use - with Sonoff Pow thresholds ### 2.0.5 20161018 - Add updates to user_config.h - moved SEND_TELEMETRY_DS18B20 and SEND_TELEMETRY_DHT to module area. - As Sonoff TH10/16 does not have the logic installed for GPIO04 You'll have to select ONE of both - Add Sonoff Pow support (experimental until Pow tested) - Add command Status 8 to display Sonoff Pow energy values - Add command MqttUnits On|Off to add units to values - Change web main page header character size - Change On/Off to ON/OFF status messages to satisfy openHAB - Change TEMP to TEMPERATURE and HUM to HUMIDITY ### 2.0.4 20161009 - Add MQTT_BUTTON_RETAIN, SAVE_DATA and SAVE_STATE defines to user_config.h (#35) - Update ButtonRetain to remove retained message(s) from broker when turned off - Add Retain for second relay on Sonoff Dual - Provide power status messages with device topic index if requested ### 2.0.3 20161008 - Update wifi initialization - Add command BUTTONRETAIN for optional MQTT retain on button press (#35) - Add command SAVESTATE to disable power state save. May be used with MQTT retain ### 2.0.2 20161006 - Fix wifi issue 2186 ### 2.0.1 20161002 - Fix button press ### 2.0.0 20161002 - Update Sonoff TH10/16 sensor pins (My TH10 only has GPIO14 connected) - Add full support for Sonoff dual ### 1.0.35 20160929 - Add more lines to console - Add timeout and disable MQTT on web upload - Add command SAVEDATA to control parameter save (for flash wear afficionados) (#30) ### 1.0.34 20160926 - Fix button press six and seven - Add more information to webserver ### 1.0.33 20160915 - Better WPS error message - Separate webserver code from support.ino into webserver.ino - Fix webserver User by removing unwanted restart option ### 1.0.32 20160913 - Add Wifi Protected Setup (WPS) as third option for initial config - Add command WIFICONFIG replacing deprecated command SMARTCONFIG - Add option WIFICONFIG 3 to start WPSconfig - Add option WIFICONFIG 0 to start saved Wifi config tool (WPSconfig, Smartconfig or Wifimanager) - Change button behaviour - See Wiki ### 1.0.31 20160907 - Fix DS18B20 misread if teleperiod = 2 - Tuned sensor code - Updated prefered ElectroDragon connection to Relay 1 and Button 1 - Moved SONOFF and ELECTRO_DRAGON port config to user_config.h ### 1.0.30 20160902 - Fix command TELEPERIOD 0 - Add ESP- tag to UDP log message for easy rsyslogd filtering - Add ElectroDragon (Relay 2 only) functionality. Select with #define MODULE ELECTRO_DRAGON - Add ? as null message alternative - Add DHT temperature and humidity telemetry support. Enable with #define SEND_TELEMETRY_DHT - Add DS18B20 temperature telemetry support. Enable with #define SEND_TELEMETRY_DS18B20 - Restrict HOSTNAME, MQTTCLIENT, TOPIC and BUTTONTOPIC in topic mode only ### 1.0.29 20160831 - Allow UPGRADE, OTAURL, RESTART, RESET, MQTTHOST, MQTTPORT, MQTTUSER, MQTTPASSWORD and WEBSERVER also in group mode ### 1.0.28 20160831 - Add webserver state to status 5 - Add optional PUB_PREFIX2 (tele) for telemetry usage - Add command TELEPERIOD - Fix syntax message - Change memory status display ### 1.0.27 20160831 - Add sketch flash size - Add console to webserver - Add command weblog - Change WifiManager web pages to minimal - Change display default hostname and MQTT client id in webserver - Change HTTP command interface to http://sonoff-1234/cm?cmnd=light 2 - Change HEARTBEAT to UPTIME ### 1.0.26 20160829 - Add define USE_WEBSERVER to disable web server code in source - Add file upload as alternative for ota upload to webserver - Add information to webserver - Add command hostname - Add command logport - Change HTTP command interface to http://sonoff-1234/cmd?cmnd=light 2 - Change button behaviour with regards to Smartconfig and OTA upload. See README.md - Enforce default hostname to either "%s-%04d" or user defined without any % - Enforce default mqtt client id to either "DVES_%06X" or user defined without any % ### 1.0.25 20160822 - Remove config system halts to keep ota available ### 1.0.24 20160821 - Add test for MQTT_SUBTOPIC - Change log range to LOG_LEVEL_ALL - Change MQTT introduction messages - Moved MQTT_MAX_PACKET_SIZE warning message to introduction messages ### 1.0.23 20160821 - Add option USE_SPIFFS to move config from flash to spiffs - Add webserver with options 0 (off), 1 (user) and 2 (admin) - Add HTTP command interface (http://sonoff-1234/c?cmnd=light 2) - Add wifimanager countdown counter - Add command line webpage - Add relay control to wifimanager - Add restart option 99 to force restart - Fix wifi hostname - Fix NETBIOS hostname problem by reducing default hostname length - Fix possible exception if WIFI_HOSTNAME is changed - Fix upgrade messages - Reduce memory use by redesigning config routines - Split syntax message - Rename define SERIAL_IO to USE_SERIAL ### 1.0.22 20160814 - Add all MQTT parameters for configuration - Add wifimanager to configure Wifi and MQTT via web server - Change NTP time handling - Fix Smartconfig parameter buffer overflow - Fix PlatformIO warnings ### 1.0.21 20160808 - Remove semaphore as subscription flooding (more than 15 subscriptions per second) is managed by SDK (LmacRxBlk:1) - Add optional RTC interrupt (define USE_TICKER) to keep RTC synced during subscription flooding - Remove heartbeatflag ### 1.0.20 20160805 - Add semaphore to handle out of memory when too many subscriptions requested - Use Daylight Saving (DST) parameters from user_config.h when timezone = 99 - Add status 7 option displaying RTC information - Add ledstate to status 0 ### 1.0.19 20160803 - Fix possible MQTT_CLIENT_ID induced Exception(28) ### 1.0.18 20160803 - Moved Cfg_Default - Fix negative data handling - Remove MQTT information from status 1 and add labels to status 1 - Add mac address to status 5 - Add MQTT ClientId, UserId and Password to status 6 ### 1.0.17 20160731 - Better variable range checking - Change ambiguous connection messages - Add timestamp to serial message ### 1.0.16 20160729 - Moved wifi, rtc, syslog and config to support.ino - Fixed button action when buttontopic is used. Introduced with 1.0.15 - Better buffer overflow checks (strlcpy) ### 1.0.15 20160728 - Removed pubsubclient config changes from sonoff.ino as it doesn't work - reapply MQTT_MAX_PACKET_SIZE 256 and MQTT_KEEPALIVE 120 to PubSubClient.h - Add status 0 option displaying all status messages - Change MQTT_MAX_PACKET_SIZE from 1024 to 256 - Add buffer overflow checks (snprintf and strncpy) - Implemented common string sizes ### 1.0.14 20160722 - Seperate user config from sonoff.ino to user_config.h (pucebaboon) - Change defaults from sidnas2 to domus1 - Add MQTT status message as status 6 (pucebaboon) - Add status type to message (pucebaboon) - Add pubsubclient config changes to sonoff.ino (pucebaboon) ### 1.0.13 20160702 - Add Ledstate 1 option to show power state on led ### 1.0.12 20160529 - Allow disable of button topic using "0" ### 1.0.11 20160524 - Provide button response if MQTT connection lost ### 1.0.10 20160520 - Add optional button topic to assist external MQTT clients - Change version notation - Reset default values ### 1.0.9 20160503 - Add more blinks - Add reset 2 option erasing flash - Add status 5 option displaying network info - Add syslog check for Wifi connection - Resize MqttPublish log array - Change Wifi smartconfig active from 100 to 60 seconds - Update Wifi initialization ### 1.0.8 20160430 - Remove use of Wifi config data from SDK - Add status 3 (syslog info) and status 4 (flash info) - Add restart option to button (5 quick presses) ### 1.0.7 20160420 - Add UDP syslog support - Change HOST command to MQTTHOST command - Add commands SYSLOG, SERIALLOG and LOGHOST - Change hostname to lower case to distinguise between open-sdk version - Add support for ESP-12F used in my modified wkaku power socket switch - Fix timezone command - Add RTC month names for future use - Modify button code - Remove initialization errors by better use of MQTT loop ### 1.0.6 20160406 - Removed Wifi AP mode (#1) - Add test for Arduino IDE version >= 1.6.8 - Fix RTC time sync code ### 1.0.5 20160310 - Initial public release - Show debug info by selecting option from IDE Tools Debug port: Serial