/* my_user_config.h - user specific configuration for Sonoff-Tasmota Copyright (C) 2019 Theo Arends This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ #ifndef _MY_USER_CONFIG_H_ #define _MY_USER_CONFIG_H_ /*********************************************************************************************\ * This file consists of TWO sections. * * SECTION 1: * The first section contains PARAMETERS overriding flash settings if define CFG_HOLDER is CHANGED. * All parameters can be persistent changed online using commands via MQTT, WebConsole or Serial. * Corresponding MQTT/Serial/Console commands are shown in [brackets] * * SECTION 2: * The second section contains Enabled and Disabled FEATURES allowing different program size. * Changes in this section do NOT need a change of define CFG_HOLDER. * * ATTENTION: * Users are advised to use the user_config_override.h file for most changes. \*********************************************************************************************/ //#define USE_CONFIG_OVERRIDE // Uncomment to use user_config_override.h file. See README.md /*********************************************************************************************\ * SECTION 1 * - After initial load any change here only take effect if CFG_HOLDER is changed too \*********************************************************************************************/ // -- Master parameter control -------------------- #define CFG_HOLDER 4617 // [Reset 1] Change this value (max 32000) to load SECTION1 configuration parameters to flash // -- Project ------------------------------------- #define PROJECT "sonoff" // PROJECT is used as the default topic delimiter // If not selected the default will be SONOFF_BASIC //#define MODULE SONOFF_BASIC // [Module] Select default model from sonoff_template.h #define SAVE_DATA 1 // [SaveData] Save changed parameters to Flash (0 = disable, 1 - 3600 seconds) #define SAVE_STATE 1 // [SetOption0] Save changed power state to Flash (0 = disable, 1 = enable) #define BOOT_LOOP_OFFSET 1 // [SetOption36] Number of boot loops before starting restoring defaults (0 = disable, 1..200 = boot loops offset) // -- Wifi ---------------------------------------- #define WIFI_IP_ADDRESS "0.0.0.0" // [IpAddress1] Set to 0.0.0.0 for using DHCP or enter a static IP address #define WIFI_GATEWAY "192.168.1.1" // [IpAddress2] If not using DHCP set Gateway IP address #define WIFI_SUBNETMASK "255.255.255.0" // [IpAddress3] If not using DHCP set Network mask #define WIFI_DNS "192.168.1.1" // [IpAddress4] If not using DHCP set DNS IP address (might be equal to WIFI_GATEWAY) #define STA_SSID1 "" // [Ssid1] Wifi SSID #define STA_PASS1 "" // [Password1] Wifi password #define STA_SSID2 "" // [Ssid2] Optional alternate AP Wifi SSID #define STA_PASS2 "" // [Password2] Optional alternate AP Wifi password #define WIFI_CONFIG_TOOL WIFI_RETRY // [WifiConfig] Default tool if wifi fails to connect // (WIFI_RESTART, WIFI_SMARTCONFIG, WIFI_MANAGER, WIFI_WPSCONFIG, WIFI_RETRY, WIFI_WAIT, WIFI_SERIAL) #define WIFI_CONFIG_NO_SSID WIFI_WPSCONFIG // Default tool if wifi fails to connect and no SSID is configured // (WIFI_SMARTCONFIG, WIFI_MANAGER, WIFI_WPSCONFIG, WIFI_SERIAL) // *** NOTE: When WPS is disabled by USE_WPS below, WIFI_WPSCONFIG will execute WIFI_MANAGER *** // *** NOTE: When WIFI_MANAGER is disabled by USE_WEBSERVER below, WIFI_MANAGER will execute WIFI_SMARTCONFIG *** // *** NOTE: When WIFI_SMARTCONFIG is disabled by USE_SMARTCONFIG below, WIFI_SMARTCONFIG will execute WIFI_SERIAL *** // -- Syslog -------------------------------------- #define SYS_LOG_HOST "" // [LogHost] (Linux) syslog host #define SYS_LOG_PORT 514 // [LogPort] default syslog UDP port #define SYS_LOG_LEVEL LOG_LEVEL_NONE // [SysLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE) #define SERIAL_LOG_LEVEL LOG_LEVEL_INFO // [SerialLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE) #define WEB_LOG_LEVEL LOG_LEVEL_INFO // [WebLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE) // -- Ota ----------------------------------------- #define OTA_URL "http://thehackbox.org/tasmota/release/sonoff.bin" // [OtaUrl] // -- MQTT ---------------------------------------- #define MQTT_USE 1 // [SetOption3] Select default MQTT use (0 = Off, 1 = On) #define MQTT_HOST "" // [MqttHost] #define MQTT_FINGERPRINT1 "00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00" // [MqttFingerprint1] #define MQTT_FINGERPRINT2 "A5 02 FF 13 99 9F 8B 39 8E F1 83 4F 11 23 65 0B 32 36 FC 07" // [MqttFingerprint2] #define MQTT_PORT 1883 // [MqttPort] MQTT port (10123 on CloudMQTT) #define MQTT_USER "DVES_USER" // [MqttUser] MQTT user #define MQTT_PASS "DVES_PASS" // [MqttPassword] MQTT password #define MQTT_BUTTON_RETAIN 0 // [ButtonRetain] Button may send retain flag (0 = off, 1 = on) #define MQTT_POWER_RETAIN 0 // [PowerRetain] Power status message may send retain flag (0 = off, 1 = on) #define MQTT_SWITCH_RETAIN 0 // [SwitchRetain] Switch may send retain flag (0 = off, 1 = on) #define MQTT_BUTTON_SWITCH_FORCE_LOCAL 0 // [SetOption61] Force local operation when button/switch topic is set (0 = off, 1 = on) #define MQTT_STATUS_OFF "OFF" // [StateText1] Command or Status result when turned off (needs to be a string like "0" or "Off") #define MQTT_STATUS_ON "ON" // [StateText2] Command or Status result when turned on (needs to be a string like "1" or "On") #define MQTT_CMND_TOGGLE "TOGGLE" // [StateText3] Command to send when toggling (needs to be a string like "2" or "Toggle") #define MQTT_CMND_HOLD "HOLD" // [StateText4] Command to send when button is kept down for over KEY_HOLD_TIME * 0.1 seconds (needs to be a string like "HOLD") // -- MQTT topics --------------------------------- // Example "tasmota/bedroom/%topic%/%prefix%/" up to 80 characers #define MQTT_FULLTOPIC "%prefix%/%topic%/" // [FullTopic] Subscribe and Publish full topic name - Legacy topic // %prefix% token options #define SUB_PREFIX "cmnd" // [Prefix1] Sonoff devices subscribe to %prefix%/%topic% being SUB_PREFIX/MQTT_TOPIC and SUB_PREFIX/MQTT_GRPTOPIC #define PUB_PREFIX "stat" // [Prefix2] Sonoff devices publish to %prefix%/%topic% being PUB_PREFIX/MQTT_TOPIC #define PUB_PREFIX2 "tele" // [Prefix3] Sonoff devices publish telemetry data to %prefix%/%topic% being PUB_PREFIX2/MQTT_TOPIC/UPTIME, POWER and TIME // May be named the same as PUB_PREFIX // %topic% token options (also ButtonTopic and SwitchTopic) #define MQTT_TOPIC PROJECT // [Topic] (unique) MQTT device topic, set to 'PROJECT "_%06X"' for unique topic including device MAC address #define MQTT_GRPTOPIC "sonoffs" // [GroupTopic] MQTT Group topic #define MQTT_BUTTON_TOPIC "0" // [ButtonTopic] MQTT button topic, "0" = same as MQTT_TOPIC, set to 'PROJECT "_BTN_%06X"' for unique topic including device MAC address #define MQTT_SWITCH_TOPIC "0" // [SwitchTopic] MQTT button topic, "0" = same as MQTT_TOPIC, set to 'PROJECT "_SW_%06X"' for unique topic including device MAC address #define MQTT_CLIENT_ID "DVES_%06X" // [MqttClient] Also fall back topic using Chip Id = last 6 characters of MAC address // -- MQTT - Telemetry ---------------------------- #define TELE_PERIOD 300 // [TelePeriod] Telemetry (0 = disable, 10 - 3600 seconds) #define TELE_ON_POWER 0 // [SetOption59] send tele/STATE together with stat/RESULT (0 = Disable, 1 = Enable) // -- MQTT - Domoticz ----------------------------- #define DOMOTICZ_UPDATE_TIMER 0 // [DomoticzUpdateTimer] Send relay status (0 = disable, 1 - 3600 seconds) // -- MQTT - Home Assistant Discovery ------------- #define HOME_ASSISTANT_DISCOVERY_ENABLE 0 // [SetOption19] Home Assistant Discovery (0 = Disable, 1 = Enable) // -- HTTP ---------------------------------------- #define WEB_SERVER 2 // [WebServer] Web server (0 = Off, 1 = Start as User, 2 = Start as Admin) #define WEB_PASSWORD "" // [WebPassword] Web server Admin mode Password for WEB_USERNAME (empty string = Disable) #define FRIENDLY_NAME "Sonoff" // [FriendlyName] Friendlyname up to 32 characters used by webpages and Alexa #define EMULATION EMUL_NONE // [Emulation] Select Belkin WeMo (single relay/light) or Hue Bridge emulation (multi relay/light) (EMUL_NONE, EMUL_WEMO or EMUL_HUE) // HTML hex color codes. Only 3 and 6 digit hex string values are supported!! See https://www.w3schools.com/colors/colors_hex.asp #define COLOR_TEXT "#000" // [WebColor1] Global text color - Black #define COLOR_BACKGROUND "#fff" // [WebColor2] Global background color - White #define COLOR_FORM "#f2f2f2" // [WebColor3] Form background color - Greyish #define COLOR_INPUT_TEXT "#000" // [WebColor4] Input text color - Black #define COLOR_INPUT "#fff" // [WebColor5] Input background color - White #define COLOR_CONSOLE_TEXT "#000" // [WebColor6] Console text color - Black #define COLOR_CONSOLE "#fff" // [WebColor7] Console background color - White #define COLOR_TEXT_WARNING "#f00" // [WebColor8] Warning text color - Red #define COLOR_TEXT_SUCCESS "#008000" // [WebColor9] Success text color - Green #define COLOR_BUTTON_TEXT "#fff" // [WebColor10] Button text color - White #define COLOR_BUTTON "#1fa3ec" // [WebColor11] Button color - Blueish #define COLOR_BUTTON_HOVER "#0e70a4" // [WebColor12] Button color when hovered over - Darker blueish #define COLOR_BUTTON_RESET "#d43535" // [WebColor13] Restart/Reset/Delete button color - Redish #define COLOR_BUTTON_RESET_HOVER "#931f1f" // [WebColor14] Restart/Reset/Delete button color when hovered over - Darker redish #define COLOR_BUTTON_SAVE "#47c266" // [WebColor15] Save button color - Greenish #define COLOR_BUTTON_SAVE_HOVER "#5aaf6f" // [WebColor16] Save button color when hovered over - Darker greenish #define COLOR_TIMER_TAB_TEXT "#fff" // [WebColor17] Config timer tab text color - White #define COLOR_TIMER_TAB_BACKGROUND "#999" // [WebColor18] Config timer tab background color - Light grey // -- mDNS ---------------------------------------- #define MDNS_ENABLED 0 // [SetOption55] Use mDNS (0 = Disable, 1 = Enable) // -- Time - Up to three NTP servers in your region #define NTP_SERVER1 "pool.ntp.org" // [NtpServer1] Select first NTP server by name or IP address (129.250.35.250) #define NTP_SERVER2 "nl.pool.ntp.org" // [NtpServer2] Select second NTP server by name or IP address (5.39.184.5) #define NTP_SERVER3 "0.nl.pool.ntp.org" // [NtpServer3] Select third NTP server by name or IP address (93.94.224.67) // -- Time - Start Daylight Saving Time and timezone offset from UTC in minutes #define TIME_DST_HEMISPHERE North // [TimeDst] Hemisphere (0 or North, 1 or South) #define TIME_DST_WEEK Last // Week of month (0 or Last, 1 or First, 2 or Second, 3 or Third, 4 or Fourth) #define TIME_DST_DAY Sun // Day of week (1 or Sun, 2 or Mon, 3 or Tue, 4 or Wed, 5 or Thu, 6 or Fri, 7 or Sat) #define TIME_DST_MONTH Mar // Month (1 or Jan, 2 or Feb, 3 or Mar, 4 or Apr, 5 or May, 6 or Jun, 7 or Jul, 8 or Aug, 9 or Sep, 10 or Oct, 11 or Nov, 12 or Dec) #define TIME_DST_HOUR 2 // Hour (0 to 23) #define TIME_DST_OFFSET +120 // Offset from UTC in minutes (-780 to +780) // -- Time - Start Standard Time and timezone offset from UTC in minutes #define TIME_STD_HEMISPHERE North // [TimeStd] Hemisphere (0 or North, 1 or South) #define TIME_STD_WEEK Last // Week of month (0 or Last, 1 or First, 2 or Second, 3 or Third, 4 or Fourth) #define TIME_STD_DAY Sun // Day of week (1 or Sun, 2 or Mon, 3 or Tue, 4 or Wed, 5 or Thu, 6 or Fri, 7 or Sat) #define TIME_STD_MONTH Oct // Month (1 or Jan, 2 or Feb, 3 or Mar, 4 or Apr, 5 or May, 6 or Jun, 7 or Jul, 8 or Aug, 9 or Sep, 10 or Oct, 11 or Nov, 12 or Dec) #define TIME_STD_HOUR 3 // Hour (0 to 23) #define TIME_STD_OFFSET +60 // Offset from UTC in minutes (-780 to +780) // -- Location ------------------------------------ #define LATITUDE 48.858360 // [Latitude] Your location to be used with sunrise and sunset #define LONGITUDE 2.294442 // [Longitude] Your location to be used with sunrise and sunset // -- Application --------------------------------- #define APP_TIMEZONE 1 // [Timezone] +1 hour (Amsterdam) (-13 .. 14 = hours from UTC, 99 = use TIME_DST/TIME_STD) #define APP_LEDSTATE LED_POWER // [LedState] Function of led // (LED_OFF, LED_POWER, LED_MQTTSUB, LED_POWER_MQTTSUB, LED_MQTTPUB, LED_POWER_MQTTPUB, LED_MQTT, LED_POWER_MQTT) #define APP_LEDMASK 0xFFFF // [LedMask] Assign Relay to Power led (0xFFFF is default) #define APP_PULSETIME 0 // [PulseTime] Time in 0.1 Sec to turn off power for relay 1 (0 = disabled) #define APP_POWERON_STATE POWER_ALL_SAVED // [PowerOnState] Power On Relay state // (POWER_ALL_OFF, POWER_ALL_ON, POWER_ALL_SAVED_TOGGLE, POWER_ALL_SAVED, POWER_ALL_ALWAYS_ON, POWER_ALL_OFF_PULSETIME_ON) #define APP_BLINKTIME 10 // [BlinkTime] Time in 0.1 Sec to blink/toggle power for relay 1 #define APP_BLINKCOUNT 10 // [BlinkCount] Number of blinks (0 = 32000) #define APP_SLEEP 0 // [Sleep] Sleep time to lower energy consumption (0 = Off, 1 - 250 mSec) #define KEY_DEBOUNCE_TIME 50 // [ButtonDebounce] Number of mSeconds button press debounce time #define KEY_HOLD_TIME 40 // [SetOption32] Number of 0.1 seconds to hold Button or external Pushbutton before sending HOLD message #define SWITCH_DEBOUNCE_TIME 50 // [SwitchDebounce] Number of mSeconds switch press debounce time #define SWITCH_MODE TOGGLE // [SwitchMode] TOGGLE, FOLLOW, FOLLOW_INV, PUSHBUTTON, PUSHBUTTON_INV, PUSHBUTTONHOLD, PUSHBUTTONHOLD_INV, PUSHBUTTON_TOGGLE (the wall switch state) #define WS2812_LEDS 30 // [Pixels] Number of WS2812 LEDs to start with (max is 512) #define TEMP_CONVERSION 0 // [SetOption8] Return temperature in (0 = Celsius or 1 = Fahrenheit) #define PRESSURE_CONVERSION 0 // [SetOption24] Return pressure in (0 = hPa or 1 = mmHg) #define TEMP_RESOLUTION 1 // [TempRes] Maximum number of decimals (0 - 3) showing sensor Temperature #define HUMIDITY_RESOLUTION 1 // [HumRes] Maximum number of decimals (0 - 3) showing sensor Humidity #define PRESSURE_RESOLUTION 1 // [PressRes] Maximum number of decimals (0 - 3) showing sensor Pressure #define ENERGY_RESOLUTION 3 // [EnergyRes] Maximum number of decimals (0 - 5) showing energy usage in kWh #define CALC_RESOLUTION 3 // [CalcRes] Maximum number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE /*********************************************************************************************\ * END OF SECTION 1 * * SECTION 2 * - Enable a feature by removing both // in front of it * - Disable a feature by preceding it with // \*********************************************************************************************/ // -- Localization -------------------------------- // If non selected the default en-GB will be used //#define MY_LANGUAGE bg-BG // Bulgarian in Bulgaria //#define MY_LANGUAGE cs-CZ // Czech in Czech //#define MY_LANGUAGE de-DE // German in Germany //#define MY_LANGUAGE el-GR // Greek in Greece //#define MY_LANGUAGE en-GB // English in Great Britain. Enabled by Default //#define MY_LANGUAGE es-ES // Spanish in Spain //#define MY_LANGUAGE fr-FR // French in France //#define MY_LANGUAGE he-HE // Hebrew in Israel //#define MY_LANGUAGE hu-HU // Hungarian in Hungary //#define MY_LANGUAGE it-IT // Italian in Italy //#define MY_LANGUAGE ko-KO // Korean in Korea //#define MY_LANGUAGE nl-NL // Dutch in the Netherlands //#define MY_LANGUAGE pl-PL // Polish in Poland //#define MY_LANGUAGE pt-BR // Portuguese in Brazil //#define MY_LANGUAGE pt-PT // Portuguese in Portugal //#define MY_LANGUAGE ru-RU // Russian in Russia //#define MY_LANGUAGE sk-SK // Slovak in Slovakia //#define MY_LANGUAGE sv-SE // Swedish in Sweden //#define MY_LANGUAGE tr-TR // Turkish in Turkey //#define MY_LANGUAGE uk-UK // Ukrainian in Ukraine //#define MY_LANGUAGE zh-CN // Chinese (Simplified) in China //#define MY_LANGUAGE zh-TW // Chinese (Traditional) in Taiwan // -- Wifi Config tools --------------------------- #define WIFI_SOFT_AP_CHANNEL 1 // Soft Access Point Channel number between 1 and 13 as used by Wifi Manager web GUI //#define USE_WPS // Add support for WPS as initial wifi configuration tool (+33k code, 1k mem (5k mem with core v2.4.2+)) //#define USE_SMARTCONFIG // Add support for Wifi SmartConfig as initial wifi configuration tool (+23k code, +0.6k mem) // -- OTA ----------------------------------------- //#define USE_ARDUINO_OTA // Add optional support for Arduino OTA (+13k code) // -- MQTT ---------------------------------------- #define MQTT_TELE_RETAIN 0 // Tele messages may send retain flag (0 = off, 1 = on) // -- MQTT - Domoticz ----------------------------- #define USE_DOMOTICZ // Enable Domoticz (+6k code, +0.3k mem) #define DOMOTICZ_IN_TOPIC "domoticz/in" // Domoticz Input Topic #define DOMOTICZ_OUT_TOPIC "domoticz/out" // Domoticz Output Topic // -- MQTT - Home Assistant Discovery ------------- #define USE_HOME_ASSISTANT // Enable Home Assistant Discovery Support (+7k code) #define HOME_ASSISTANT_DISCOVERY_PREFIX "homeassistant" // Home Assistant discovery prefix // -- MQTT - TLS - AWS IoT ------------------------ // Using TLS starting with version v6.5.0.16 compilation will only work using Core 2.4.2 and 2.5.2. No longer supported: 2.3.0 //#define USE_MQTT_TLS // Use TLS for MQTT connection (+34.5k code, +7.0k mem and +4.8k additional during connection handshake) // #define USE_MQTT_TLS_CA_CERT // Force full CA validation instead of fingerprints, slower, but simpler to use (+2.2k code, +1.9k mem during connection handshake) // #define USE_MQTT_TLS_FORCE_EC_CIPHER // Force Elliptic Curve cipher (higher security) required by some servers (automatically enabled with USE_MQTT_AWS_IOT) (+11.4k code, +0.4k mem) // #define USE_MQTT_AWS_IOT // Enable MQTT for AWS IoT - requires a private key (+11.4k code, +0.4k mem) // Note: you need to generate a private key + certificate per device and update 'sonoff/sonoff_aws_iot.cpp' // Full documentation here: https://github.com/arendst/Sonoff-Tasmota/wiki/AWS-IoT // -- KNX IP Protocol ----------------------------- //#define USE_KNX // Enable KNX IP Protocol Support (+9.4k code, +3k7 mem) #define USE_KNX_WEB_MENU // Enable KNX WEB MENU (+8.3k code, +144 mem) // -- HTTP ---------------------------------------- #define USE_WEBSERVER // Enable web server and Wifi Manager (+66k code, +8k mem) #define WEB_PORT 80 // Web server Port for User and Admin mode #define WEB_USERNAME "admin" // Web server Admin mode user name // #define USE_JAVASCRIPT_ES6 // Enable ECMAScript6 syntax using less JavaScript code bytes (fails on IE11) #define USE_EMULATION_HUE // Enable Hue Bridge emulation for Alexa (+14k code, +2k mem common) #define USE_EMULATION_WEMO // Enable Belkin WeMo emulation for Alexa (+6k code, +2k mem common) // -- mDNS ---------------------------------------- #define USE_DISCOVERY // Enable mDNS for the following services (+8k code or +23.5k code with core 2_5_x, +0.3k mem) #define WEBSERVER_ADVERTISE // Provide access to webserver by name .local/ #define MQTT_HOST_DISCOVERY // Find MQTT host server (overrides MQTT_HOST if found) // -- Time ---------------------------------------- #define USE_TIMERS // Add support for up to 16 timers (+2k2 code) #define USE_TIMERS_WEB // Add timer webpage support (+4k5 code) #define USE_SUNRISE // Add support for Sunrise and sunset tools (+16k) #define SUNRISE_DAWN_ANGLE DAWN_NORMAL // Select desired Dawn Angle from (DAWN_NORMAL, DAWN_CIVIL, DAWN_NAUTIC, DAWN_ASTRONOMIC) // -- Rules or Script ---------------------------- // Select none or only one of the below defines #define USE_RULES // Add support for rules (+8k code) //#define USE_SCRIPT // Add support for script (+17k code) #define USE_SCRIPT_FATFS 4 // Script: Add FAT FileSystem Support // #define USE_EXPRESSION // Add support for expression evaluation in rules (+3k2 code, +64 bytes mem) // #define SUPPORT_MQTT_EVENT // Support trigger event with MQTT subscriptions (+3k5 code) // -- Optional modules ---------------------------- #define USE_SONOFF_IFAN // Add support for Sonoff iFan02 and iFan03 (+2k code) #define USE_TUYA_DIMMER // Add support for Tuya Serial Dimmer #define TUYA_DIMMER_ID 0 // Default dimmer Id #define USE_ARMTRONIX_DIMMERS // Add support for Armtronix Dimmers (+1k4 code) #define USE_PS_16_DZ // Add support for PS-16-DZ Dimmer and Sonoff L1 (+2k code) //#define ROTARY_V1 // Add support for MI Desk Lamp // -- Counter input ------------------------------- #define USE_COUNTER // Enable inputs as counter (+0k8 code) // -- Internal Analog input ----------------------- //#define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices // -- One wire sensors ---------------------------- // WARNING: Select none for default one DS18B20 sensor or enable one of the following two options for multiple sensors //#define USE_DS18x20_LEGACY // Optional for more than one DS18x20 sensors with dynamic scan using library OneWire (+1k5 code) #define USE_DS18x20 // Optional for more than one DS18x20 sensors with id sort, single scan and read retry (+1k3 code) // #define W1_PARASITE_POWER // If using USE_DS18x20 then optimize for parasite powered sensors // #define DS18B20_INTERNAL_PULLUP // Use INPUT_PULLUP internal pullup resistors for single DS18B20 // -- I2C sensors --------------------------------- #define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram) #ifdef USE_I2C #define USE_SHT // Enable SHT1X sensor (+1k4 code) #define USE_HTU // Enable HTU21/SI7013/SI7020/SI7021 sensor (I2C address 0x40) (+1k5 code) #define USE_BMP // Enable BMP085/BMP180/BMP280/BME280 sensors (I2C addresses 0x76 and 0x77) (+4k4 code) // #define USE_BME680 // Enable support for BME680 sensor using Bosch BME680 library (+4k code) #define USE_BH1750 // Enable BH1750 sensor (I2C address 0x23 or 0x5C) (+0k5 code) // #define USE_VEML6070 // Enable VEML6070 sensor (I2C addresses 0x38 and 0x39) (+1k5 code) #define USE_VEML6070_RSET 270000 // VEML6070, Rset in Ohm used on PCB board, default 270K = 270000ohm, range for this sensor: 220K ... 1Meg #define USE_VEML6070_SHOW_RAW // VEML6070, shows the raw value of UV-A // #define USE_ADS1115 // Enable ADS1115 16 bit A/D converter (I2C address 0x48, 0x49, 0x4A or 0x4B) based on Adafruit ADS1x15 library (no library needed) (+0k7 code) // #define USE_ADS1115_I2CDEV // Enable ADS1115 16 bit A/D converter (I2C address 0x48, 0x49, 0x4A or 0x4B) using library i2cdevlib-Core and i2cdevlib-ADS1115 (+2k code) // #define USE_INA219 // Enable INA219 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+1k code) #define USE_SHT3X // Enable SHT3x (I2C address 0x44 or 0x45) or SHTC3 (I2C address 0x70) sensor (+0k7 code) // #define USE_TSL2561 // Enable TSL2561 sensor (I2C address 0x29, 0x39 or 0x49) using library Joba_Tsl2561 (+2k3 code) // #define USE_MGS // Enable Xadow and Grove Mutichannel Gas sensor using library Multichannel_Gas_Sensor (+10k code) #define MGS_SENSOR_ADDR 0x04 // Default Mutichannel Gas sensor i2c address // #define USE_SGP30 // Enable SGP30 sensor (I2C address 0x58) (+1k1 code) // #define USE_SI1145 // Enable SI1145/46/47 sensor (I2C address 0x60) (+1k code) #define USE_LM75AD // Enable LM75AD sensor (I2C addresses 0x48 - 0x4F) (+0k5 code) // #define USE_APDS9960 // Enable APDS9960 Proximity Sensor (I2C address 0x39). Disables SHT and VEML6070 (+4k7 code) // #define USE_MCP230xx // Enable MCP23008/MCP23017 - Must define I2C Address in #define USE_MCP230xx_ADDR below - range 0x20 - 0x27 (+4k7 code) // #define USE_MCP230xx_ADDR 0x20 // Enable MCP23008/MCP23017 I2C Address to use (Must be within range 0x20 through 0x27 - set according to your wired setup) // #define USE_MCP230xx_OUTPUT // Enable MCP23008/MCP23017 OUTPUT support through sensor29 commands (+1k5 code) // #define USE_MCP230xx_DISPLAYOUTPUT // Enable MCP23008/MCP23017 to display state of OUTPUT pins on Web UI (+0k2 code) // #define USE_PCA9685 // Enable PCA9685 I2C HW PWM Driver - Must define I2C Address in #define USE_PCA9685_ADDR below - range 0x40 - 0x47 (+1k4 code) // #define USE_PCA9685_ADDR 0x40 // Enable PCA9685 I2C Address to use (Must be within range 0x40 through 0x47 - set according to your wired setup) // #define USE_PCA9685_FREQ 50 // Define default PWM frequency in Hz to be used (must be within 24 to 1526) - If other value is used, it will rever to 50Hz // #define USE_MPR121 // Enable MPR121 controller (I2C addresses 0x5A, 0x5B, 0x5C and 0x5D) in input mode for touch buttons (+1k3 code) // #define USE_CCS811 // Enable CCS811 sensor (I2C address 0x5A) (+2k2 code) // #define USE_MPU6050 // Enable MPU6050 sensor (I2C address 0x68 AD0 low or 0x69 AD0 high) (+3K3 of code and 188 Bytes of RAM) // #define USE_MPU6050_DMP // Enable in MPU6050 to use the DMP on the chip, should create better results (+8k6 of code) // #define USE_DS3231 // Enable DS3231 external RTC in case no Wifi is avaliable. See docs in the source file (+1k2 code) // #define USE_RTC_ADDR 0x68 // Default I2C address 0x68 // #define USE_MGC3130 // Enable MGC3130 Electric Field Effect Sensor (I2C address 0x42) (+2k7 code, 0k3 mem) // #define USE_MAX44009 // Enable MAX44009 Ambient Light sensor (I2C addresses 0x4A and 0x4B) (+0k8 code) // #define USE_SCD30 // Enable Sensiron SCd30 CO2 sensor (I2C address 0x61) (+3k3 code) // #define USE_SPS30 // Enable Sensiron SPS30 particle sensor (I2C address 0x69) (+1.7 code) #define USE_ADE7953 // Enable ADE7953 Energy monitor as used on Shelly 2.5 (I2C address 0x38) (+1k5) // #define USE_VL53L0X // Enable VL53L0x time of flight sensor (I2C address 0x29) (+4k code) // #define USE_MLX90614 // Enable MLX90614 ir temp sensor (I2C address 0x5a) (+0.6k code) // #define USE_DISPLAY // Add I2C Display Support (+2k code) #define USE_DISPLAY_MODES1TO5 // Enable display mode 1 to 5 in addition to mode 0 #define USE_DISPLAY_LCD // [DisplayModel 1] Enable Lcd display (I2C addresses 0x27 and 0x3F) (+6k code) #define USE_DISPLAY_SSD1306 // [DisplayModel 2] Enable SSD1306 Oled 128x64 display (I2C addresses 0x3C and 0x3D) (+16k code) #define USE_DISPLAY_MATRIX // [DisplayModel 3] Enable 8x8 Matrix display (I2C adresseses see below) (+11k code) #define MTX_ADDRESS1 0x71 // [DisplayAddress1] I2C address of first 8x8 matrix module #define MTX_ADDRESS2 0x74 // [DisplayAddress2] I2C address of second 8x8 matrix module #define MTX_ADDRESS3 0x75 // [DisplayAddress3] I2C address of third 8x8 matrix module #define MTX_ADDRESS4 0x72 // [DisplayAddress4] I2C address of fourth 8x8 matrix module #define MTX_ADDRESS5 0x73 // [DisplayAddress5] I2C address of fifth 8x8 matrix module #define MTX_ADDRESS6 0x76 // [DisplayAddress6] I2C address of sixth 8x8 matrix module #define MTX_ADDRESS7 0x00 // [DisplayAddress7] I2C address of seventh 8x8 matrix module #define MTX_ADDRESS8 0x00 // [DisplayAddress8] I2C address of eigth 8x8 matrix module #endif // USE_I2C // -- SPI sensors --------------------------------- //#define USE_SPI // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC) #ifdef USE_SPI #ifndef USE_DISPLAY #define USE_DISPLAY // Add SPI Display support for 320x240 and 480x320 TFT #endif #define USE_DISPLAY_ILI9341 // [DisplayModel 4] Enable ILI9341 Tft 480x320 display (+19k code) // #define USE_DISPLAY_EPAPER_29 // [DisplayModel 5] Enable e-paper 2.9 inch display (+19k code) #endif // USE_SPI // -- Serial sensors ------------------------------ #define USE_MHZ19 // Add support for MH-Z19 CO2 sensor (+2k code) #define USE_SENSEAIR // Add support for SenseAir K30, K70 and S8 CO2 sensor (+2k3 code) #define CO2_LOW 800 // Below this CO2 value show green light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1) #define CO2_HIGH 1200 // Above this CO2 value show red light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1) #define USE_PMS5003 // Add support for PMS5003 and PMS7003 particle concentration sensor (+1k3 code) #define USE_NOVA_SDS // Add support for SDS011 and SDS021 particle concentration sensor (+0k7 code) #define WORKING_PERIOD 5 // Working period of the SDS Sensor, Takes a reading every X Minutes #define USE_SERIAL_BRIDGE // Add support for software Serial Bridge (+0k8 code) //#define USE_SDM120 // Add support for Eastron SDM120-Modbus energy meter (+1k7 code) #define SDM120_SPEED 2400 // SDM120-Modbus RS485 serial speed (default: 2400 baud) #define USE_SDM220 // Add extra parameters for SDM220 (+0k1 code) //#define USE_SDM630 // Add support for Eastron SDM630-Modbus energy meter (+2k code) #define SDM630_SPEED 9600 // SDM630-Modbus RS485 serial speed (default: 9600 baud) //#define USE_MP3_PLAYER // Use of the DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop #define MP3_VOLUME 10 // Set the startup volume on init, the range can be 0..30(max) //#define USE_AZ7798 // Add support for AZ-Instrument 7798 CO2 datalogger (+1k6 code) //#define USE_PN532_HSU // Add support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem) // #define USE_PN532_CAUSE_EVENTS // Cause event execution for PN532_UID= and PN532_DATA=[if defined] (+ 30 bytes code) // #define USE_PN532_DATA_FUNCTION // Add sensor40 command support for erase, setting data block content (+1k7 code, 388 bytes mem) // #define USE_PN532_DATA_RAW // Allow DATA block to be used by non-alpha-numberic data (+ 80 bytes code, 48 bytes ram) // Power monitoring sensors ----------------------- #define USE_ENERGY_MARGIN_DETECTION // Add support for Energy Margin detection (+1k6 code) #define USE_ENERGY_POWER_LIMIT // Add additional support for Energy Power Limit detection (+1k2 code) #define USE_PZEM004T // Add support for PZEM004T Energy monitor (+2k code) #define USE_PZEM_AC // Add support for PZEM014,016 Energy monitor (+1k1 code) #define USE_PZEM_DC // Add support for PZEM003,017 Energy monitor (+1k1 code) #define USE_MCP39F501 // Add support for MCP39F501 Energy monitor as used in Shelly 2 (+3k1 code) // -- Low level interface devices ----------------- #define USE_DHT // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor (1k6 code) //#define USE_MAX31855 // Add support for MAX31855 K-Type thermocouple sensor using softSPI //#define USE_MAX31865 // Add support for MAX31865 RTD sensors using softSPI #define MAX31865_PTD_WIRES 2 // PTDs come in several flavors. Pick yours #define MAX31865_PTD_RES 100 // Nominal PTD resistance at 0°C (100Ω for a PT100, 1000Ω for a PT1000, YMMV!) #define MAX31865_REF_RES 430 // Reference resistor (Usually 430Ω for a PT100, 4300Ω for a PT1000) #define MAX31865_PTD_BIAS 0 // To calibrate your not-so-good PTD // -- IR Remote features -------------------------- #define USE_IR_REMOTE // Send IR remote commands using library IRremoteESP8266 and ArduinoJson (+4k3 code, 0k3 mem, 48 iram) // #define USE_IR_SEND_AIWA // Support IRsend Aiwa protocol #define USE_IR_SEND_DISH // Support IRsend Dish protocol #define USE_IR_SEND_JVC // Support IRsend JVC protocol // #define USE_IR_SEND_LG // Support IRsend LG protocol // #define USE_IR_SEND_MITSUBISHI // Support IRsend Mitsubishi protocol #define USE_IR_SEND_NEC // Support IRsend NEC protocol #define USE_IR_SEND_PANASONIC // Support IRsend Panasonic protocol #define USE_IR_SEND_PIONEER // Support IRsend Pioneer protocol #define USE_IR_SEND_RC5 // Support IRsend Philips RC5 protocol #define USE_IR_SEND_RC6 // Support IRsend Philips RC6 protocol #define USE_IR_SEND_SAMSUNG // Support IRsend Samsung protocol // #define USE_IR_SEND_SANYO // Support IRsend Sanyo protocol // #define USE_IR_SEND_SHARP // Support IRsend Sharp protocol #define USE_IR_SEND_SONY // Support IRsend Sony protocol // #define USE_IR_SEND_WHYNTER // Support IRsend Whynter protocol // #define USE_IR_HVAC // Support for HVAC systems using IR (+3k5 code) #define USE_IR_HVAC_TOSHIBA // Support IRhvac Toshiba protocol #define USE_IR_HVAC_MITSUBISHI // Support IRhvac Mitsubischi protocol #define USE_IR_HVAC_LG // Support IRhvac LG protocol #define USE_IR_HVAC_FUJITSU // Support IRhvac Fujitsu protocol // #define USE_IR_HVAC_MIDEA // Support IRhvac Midea/Komeco protocol #define USE_IR_RECEIVE // Support for IR receiver (+7k2 code, 264 iram) #define IR_RCV_BUFFER_SIZE 100 // Max number of packets allowed in capture buffer (default 100 (*2 bytes ram)) #define IR_RCV_TIMEOUT 15 // Number of milli-Seconds of no-more-data before we consider a message ended (default 15) #define IR_RCV_MIN_UNKNOWN_SIZE 6 // Set the smallest sized "UNKNOWN" message packets we actually care about (default 6, max 255) // ------------------------------------------------ #define USE_WS2812 // WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by // #define USE_WS2812_CTYPE NEO_GRB // WS2812 Color type (NEO_RGB, NEO_GRB, NEO_BRG, NEO_RBG, NEO_RGBW, NEO_GRBW) // #define USE_WS2812_DMA // DMA supports only GPIO03 (= Serial RXD) (+1k mem). When USE_WS2812_DMA is enabled expect Exceptions on Pow #define USE_ARILUX_RF // Add support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0)) #define USE_SR04 // Add support for HC-SR04 ultrasonic devices (+1k code) //#define USE_TM1638 // Add support for TM1638 switches copying Switch1 .. Switch8 (+1k code) #define USE_HX711 // Add support for HX711 load cell (+1k5 code) // #define USE_HX711_GUI // Add optional web GUI to HX711 as scale (+1k8 code) #define USE_RF_FLASH // Add support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB (+3k code) //#define USE_TX20_WIND_SENSOR // Add support for La Crosse TX20 anemometer (+2k code) //#define USE_RC_SWITCH // Add support for RF transceiver using library RcSwitch (+2k7 code, 460 iram) //#define USE_RF_SENSOR // Add support for RF sensor receiver (434MHz or 868MHz) (+0k8 code) // #define USE_THEO_V2 // Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver (+1k4 code) // #define USE_ALECTO_V2 // Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver (+1k7 code) #define USE_SM16716 // Add support for SM16716 RGB LED controller (+0k7 code) //#define USE_HRE // Add support for Badger HR-E Water Meter (+1k4 code) /*********************************************************************************************\ * Debug features are only supported in development branch \*********************************************************************************************/ //#define USE_DEBUG_DRIVER // Use xdrv_99_debug.ino providing commands CpuChk, CfgXor, CfgDump, CfgPeek and CfgPoke /*********************************************************************************************\ * Optional firmware configurations * Select none or just one for optional features and sensors as configured in sonoff_post.h * See RELEASENOTES.md for selected features \*********************************************************************************************/ //#define FIRMWARE_CLASSIC // Create sonoff-classic with initial configuration tools WPS, SmartConfig and WifiManager //#define FIRMWARE_BASIC // Create sonoff-basic with no sensors //#define FIRMWARE_SENSORS // Create sonoff-sensors with useful sensors enabled //#define FIRMWARE_KNX_NO_EMULATION // Create sonoff-knx with KNX but without Emulation //#define FIRMWARE_DISPLAYS // Create sonoff-display with display drivers enabled //#define FIRMWARE_MINIMAL // Create sonoff-minimal as intermediate firmware for OTA-MAGIC /*********************************************************************************************\ * No user configurable items below \*********************************************************************************************/ #if defined(USE_DISCOVERY) && defined(USE_MQTT_AWS_IOT) #error "Select either USE_DISCOVERY or USE_MQTT_AWS_IOT, mDNS takes too much code space and is not needed for AWS IoT" #endif #endif // _MY_USER_CONFIG_H_