/* tasmota_configurations_ESP32.h - ESP32 only Configurations for Tasmota Copyright (C) 2021 Theo Arends This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ #ifndef _TASMOTA_CONFIGURATIONS_ESP32_H_ #define _TASMOTA_CONFIGURATIONS_ESP32_H_ #ifdef ESP32 /*********************************************************************************************\ * [tasmota32x-safeboot.bin] * Provide an image with useful supported sensors enabled * * Is a copy of FIRMWARE_MINIMAL with some additional features enabled \*********************************************************************************************/ #ifdef FIRMWARE_SAFEBOOT #undef CODE_IMAGE_STR #define CODE_IMAGE_STR "safeboot" #undef FIRMWARE_LITE // Disable tasmota-lite with no sensors #undef FIRMWARE_SENSORS // Disable tasmota-sensors with useful sensors enabled #undef FIRMWARE_KNX_NO_EMULATION // Disable tasmota-knx with KNX but without Emulation #undef FIRMWARE_DISPLAYS // Disable tasmota-display with display drivers enabled #undef FIRMWARE_IR // Disable tasmota-ir with IR full protocols activated #undef FIRMWARE_WEBCAM #undef FIRMWARE_BLUETOOTH #undef FIRMWARE_LVGL #undef FIRMWARE_TASMOTA32 /*-------------------------------------------------------------------------------------------*\ * Start copy of all undefines from FIRMWARE_MINIMAL \*-------------------------------------------------------------------------------------------*/ #undef USE_IMPROV // Disable support for IMPROV serial protocol as used by esp-web-tools (+2k code) #undef USE_TASMESH // Disable Tasmota Mesh using ESP-NOW (+11k code) #undef USE_ARDUINO_OTA // Disable support for Arduino OTA #undef USE_INFLUXDB // Disable influxdb support (+5k code) #undef USE_DOMOTICZ // Disable Domoticz #undef USE_HOME_ASSISTANT // Disable Home Assistant #undef USE_TASMOTA_DISCOVERY // Disable Tasmota Discovery support (+2k code) #undef USE_TELEGRAM // Disable support for Telegram protocol (+49k code, +7.0k mem and +4.8k additional during connection handshake) //#undef USE_MQTT_TLS // Disable TLS support won't work as the MQTTHost is not set #undef USE_KNX // Disable KNX IP Protocol Support //#undef USE_WEBSERVER // Disable Webserver #undef USE_ENHANCED_GUI_WIFI_SCAN // Disable wifi scan output with BSSID (+0k5 code) #undef USE_WEBSEND_RESPONSE // Disable command WebSend response message (+1k code) #undef USE_EMULATION // Disable Wemo or Hue emulation #undef USE_EMULATION_HUE // Disable Hue Bridge emulation for Alexa (+14k code, +2k mem common) #undef USE_EMULATION_WEMO // Disable Belkin WeMo emulation for Alexa (+6k code, +2k mem common) #undef USE_CUSTOM // Disable Custom features #undef USE_DISCOVERY // Disable Discovery services for both MQTT and web server #undef USE_TIMERS // Disable support for up to 16 timers #undef USE_TIMERS_WEB // Disable support for timer webpage #undef USE_SUNRISE // Disable support for Sunrise and sunset tools #undef USE_PING // Disable Ping command (+2k code) #undef USE_UNISHOX_COMPRESSION // Disable support for string compression in Rules or Scripts #undef USE_RULES // Disable support for rules #undef USE_SCRIPT // Disable support for script // -- Optional modules ---------------------------- #undef ROTARY_V1 // Disable support for MI Desk Lamp #undef USE_SONOFF_RF // Disable support for Sonoff Rf Bridge (+3k2 code) #undef USE_RF_FLASH // Disable support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB #undef USE_SONOFF_SC // Disable support for Sonoff Sc (+1k1 code) #undef USE_TUYA_MCU // Disable support for Tuya Serial MCU #undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code) #undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer and Sonoff L1 (+2k code) #undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code) #undef USE_BUZZER // Disable support for a buzzer (+0k6 code) #undef USE_ARILUX_RF // Disable support for Arilux RF remote controller #undef USE_SHUTTER // Disable Shutter support for up to 4 shutter with different motortypes (+6k code) #undef USE_DEEPSLEEP // Disable support for deepsleep (+1k code) #undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer #undef USE_HOTPLUG // Disable support for HotPlug #undef USE_DEVICE_GROUPS // Disable support for device groups (+3k5 code) #undef USE_PWM_DIMMER // Disable support for MJ-SD01/acenx/NTONPOWER PWM dimmers (+4k5 code) #undef USE_PWM_DIMMER_REMOTE // Disbale support for remote switches to PWM Dimmer #undef USE_KEELOQ // Disable support for Jarolift rollers by Keeloq algorithm (+4k5 code) #undef USE_SONOFF_D1 // Disable support for Sonoff D1 Dimmer (+0k7 code) #undef USE_SHELLY_DIMMER // Disable support for Shelly Dimmer (+3k code) // -- Optional light modules ---------------------- #undef USE_LIGHT // Disable support for lights #undef USE_COUNTER // Disable counters #define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices #undef USE_DS18x20 // Disable DS18x20 sensor #undef USE_I2C // Disable all I2C sensors and devices #undef USE_SPI // Disable all SPI devices #undef USE_DISPLAY // Disable Display support #undef USE_MHZ19 // Disable support for MH-Z19 CO2 sensor #undef USE_SENSEAIR // Disable support for SenseAir K30, K70 and S8 CO2 sensor #undef USE_PMS5003 // Disable support for PMS5003 and PMS7003 particle concentration sensor #undef USE_NOVA_SDS // Disable support for SDS011 and SDS021 particle concentration sensor #undef USE_HPMA // Disable support for Honeywell HPMA115S0 particle concentration sensor #undef USE_SR04 // Disable support for HC-SR04 ultrasonic devices (+1k code) #undef USE_DYP // Disable support for DYP ME-007 ultrasonic distance sensor, serial port version (+0k5 code) #undef USE_SERIAL_BRIDGE // Disable support for software Serial Bridge #undef USE_TCP_BRIDGE // DIsable support for Serial to TCP bridge (+1.3k code) #undef USE_MP3_PLAYER // Disable DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop #undef USE_AZ7798 // Disable support for AZ-Instrument 7798 CO2 datalogger #undef USE_PN532_HSU // Disable support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem) #undef USE_ZIGBEE // Disable serial communication with Zigbee CC2530 flashed with ZNP #undef USE_RDM6300 // Disable support for RDM6300 125kHz RFID Reader (+0k8) #undef USE_IBEACON // Disable support for bluetooth LE passive scan of ibeacon devices (uses HM17 module) #undef USE_GPS // Disable support for GPS and NTP Server for becoming Stratus 1 Time Source (+ 3.1kb flash, +132 bytes RAM) #undef USE_HM10 // (ESP8266 only) Disable support for HM-10 as a BLE-bridge for the LYWSD03 (+5k1 code) #undef USE_BLE_ESP32 // (ESP32 only) Disable support for native BLE on ESP32 - use new driver #undef USE_MI_ESP32 // (ESP32 only) Disable support for ESP32 as a BLE-bridge (+9k2 mem, +292k flash) #undef USE_HRXL // Disable support for MaxBotix HRXL-MaxSonar ultrasonic range finders (+0k7) #undef USE_TASMOTA_CLIENT // Disable support for Arduino Uno/Pro Mini via serial interface including flashing (+2k3 code, 44 mem) #undef USE_OPENTHERM // Disable support for OpenTherm (+15k code) #undef USE_MIEL_HVAC // Disable support for Mitsubishi Electric HVAC serial interface (+5k code) #undef USE_PROJECTOR_CTRL // Disable support for LCD/DLP Projector serial control interface #undef USE_AS608 // Disable support for AS608 optical and R503 capacitive fingerprint sensor (+3k4 code) #undef USE_TFMINIPLUS // Disable support for TFmini Plus (TFmini, TFmini-S) LiDAR modules via UART interface (+0k8) #undef USE_HRG15 // Disable support for Hydreon RG-15 Solid State Rain sensor (+1k5 code) #undef USE_VINDRIKTNING // Disable support for IKEA VINDRIKTNING particle concentration sensor (+0k6 code) #undef USE_ENERGY_SENSOR // Disable energy sensors #undef USE_DHT // Disable support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor #undef USE_MAX31855 // Disable MAX31855 K-Type thermocouple sensor using softSPI #undef USE_MAX31865 // Disable support for MAX31865 RTD sensors using softSPI #undef USE_LMT01 // Disable support for TI LMT01 temperature sensor, count pulses on single GPIO (+0k5 code) #undef USE_IR_REMOTE // Disable IR driver #undef USE_TM1638 // Disable support for TM1638 switches copying Switch1 .. Switch8 #undef USE_HX711 // Disable support for HX711 load cell #undef USE_TX20_WIND_SENSOR // Disable support for La Crosse TX20 anemometer #undef USE_TX23_WIND_SENSOR // Disable support for La Crosse TX23 anemometer #undef USE_WINDMETER // Disable support for analog anemometer (+2k2 code) #undef USE_RC_SWITCH // Disable support for RF transceiver using library RcSwitch #undef USE_RF_SENSOR // Disable support for RF sensor receiver (434MHz or 868MHz) (+0k8 code) #undef USE_HRE // Disable support for Badger HR-E Water Meter (+1k4 code) #undef USE_A4988_STEPPER // Disable support for A4988_Stepper #undef USE_THERMOSTAT // Disable support for Thermostat #undef USE_PROMETHEUS // Disable support for https://prometheus.io/ metrics exporting over HTTP /metrics endpoint #undef DEBUG_THEO // Disable debug code #undef USE_DEBUG_DRIVER // Disable debug code #undef USE_AC_ZERO_CROSS_DIMMER // Disable support for AC_ZERO_CROSS_DIMMER /*-------------------------------------------------------------------------------------------*\ * End copy of all undefines from FIRMWARE_MINIMAL * * Start FIRMWARE_SAFEBOOT specific additions \*-------------------------------------------------------------------------------------------*/ #define FIRMWARE_MINIMAL #undef FIRMWARE_MINIMAL_ONLY #undef USE_ESP32_SENSORS #undef USE_UFILESYS #undef GUI_TRASH_FILE #undef GUI_EDIT_FILE #undef USE_PING #undef USE_AUTOCONF #undef USE_BERRY #define USE_TLS #define USE_WEBSERVER #define USE_WEBCLIENT #define USE_WEBCLIENT_HTTPS #define USE_SERIAL_BRIDGE // Add support for software Serial Bridge console Tee (+0k8 code) #endif // FIRMWARE_SAFEBOOT /*********************************************************************************************\ * [tasmota32-webcam.bin] * Provide an image with useful supported sensors enabled \*********************************************************************************************/ #ifdef FIRMWARE_WEBCAM #undef CODE_IMAGE_STR #define CODE_IMAGE_STR "webcam" #define USE_WEBCAM #define ENABLE_RTSPSERVER #define USE_SPI #define USE_SDCARD #undef USE_I2C #undef USE_HOME_ASSISTANT #define USE_TASMOTA_DISCOVERY // Enable Tasmota Discovery support (+2k code) #undef USE_COUNTER #undef USE_IR_REMOTE #undef USE_AC_ZERO_CROSS_DIMMER #undef USE_PWM_DIMMER #undef USE_TUYA_MCU #undef USE_EMULATION_HUE #undef USE_EMULATION_WEMO #undef USE_ARILUX_RF #undef USE_DS18x20 #undef USE_WS2812 #undef USE_ENERGY_SENSOR //#undef USE_BERRY // Disable Berry scripting language #undef USE_MI_ESP32 // (ESP32 only) Disable support for ESP32 as a BLE-bridge (+9k2 mem, +292k flash) #endif // FIRMWARE_WEBCAM /*********************************************************************************************\ * [tasmota32-bluetooth.bin] * Provide an image with BLE support \*********************************************************************************************/ #ifdef FIRMWARE_BLUETOOTH #undef CODE_IMAGE_STR #define CODE_IMAGE_STR "bluetooth" #undef MODULE #define MODULE WEMOS // [Module] Select default module from tasmota_template.h #undef FALLBACK_MODULE #define FALLBACK_MODULE WEMOS // [Module2] Select default module on fast reboot where USER_MODULE is user template #define USE_INFLUXDB // Enable influxdb support (+5k code) #undef USE_HOME_ASSISTANT #define USE_TASMOTA_DISCOVERY #define USE_SDCARD #define USE_ADC //#undef USE_BERRY // Disable Berry scripting language #if defined(USE_MI_HOMEKIT) // Switch between Homekit and full BLE driver #define USE_MI_ESP32 #if(USE_MI_HOMEKIT != 1) // Enable(1)/ Disable(0) Homekit, only for the .c-file #undef USE_MI_HOMEKIT #endif // disable USE_MI_HOMEKIT #else #define USE_BLE_ESP32 // Enable full BLE driver #define USE_EQ3_ESP32 #define USE_MI_ESP32 // (ESP32 only) Add support for ESP32 as a BLE-bridge (+9k2 mem, +292k flash) #endif // enable USE_MI_HOMEKIT #endif // FIRMWARE_BLUETOOTH /*********************************************************************************************\ * [tasmota32-lvgl.bin] * Provide an image which includes uDisplay and LVGL driver \*********************************************************************************************/ #ifdef FIRMWARE_LVGL #undef CODE_IMAGE_STR #define CODE_IMAGE_STR "lvgl-haspmota" #undef MODULE #define MODULE WEMOS // [Module] Select default module from tasmota_template.h #undef FALLBACK_MODULE #define FALLBACK_MODULE WEMOS // [Module2] Select default module on fast reboot where USER_MODULE is user template #undef USE_DOMOTICZ #undef USE_HOME_ASSISTANT #define USE_TASMOTA_DISCOVERY // Enable Tasmota Discovery support (+2k code) #define USE_WEBCLIENT_HTTPS #define USE_I2S #define USE_SPI #define USE_LVGL #define USE_LVGL_HASPMOTA #define USE_LVGL_FREETYPE #undef SET_ESP32_STACK_SIZE #define SET_ESP32_STACK_SIZE (24 * 1024) #define USE_LVGL_PNG_DECODER #define USE_DISPLAY #define SHOW_SPLASH #define USE_XPT2046 #define USE_FT5206 #define USE_MPU_ACCEL #define USE_RTC_CHIPS // Enable RTC chip support and NTP server - Select only one #define USE_BM8563 #define USE_MLX90614 #define USE_UNIVERSAL_DISPLAY #define USE_DISPLAY_LVGL_ONLY #undef USE_DISPLAY_MODES1TO5 #undef USE_DISPLAY_LCD #undef USE_DISPLAY_SSD1306 #undef USE_DISPLAY_MATRIX #undef USE_DISPLAY_SEVENSEG #define USE_ENHANCED_GUI_WIFI_SCAN #define USE_SDCARD #define ROTARY_V1 // Add support for Rotary Encoder as used in MI Desk Lamp #define USE_TUYA_MCU // Add support for Tuya Serial MCU #ifndef TUYA_DIMMER_ID #define TUYA_DIMMER_ID 0 // Default dimmer Id #endif #undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code) //#undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer (+2k code) #undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code) #define USE_BUZZER // Add support for a buzzer (+0k6 code) //#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0)) //#define USE_DEEPSLEEP // Add support for deepsleep (+1k code) #undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer //#define USE_HOTPLUG // Add support for sensor HotPlug //#undef USE_DEVICE_GROUPS // Disable support for device groups (+5k6 code) #undef USE_PWM_DIMMER // Disable support for MJ-SD01/acenx/NTONPOWER PWM dimmers (+4k5 code) #undef USE_KEELOQ // Disable support for Jarolift rollers by Keeloq algorithm (+4k5 code) #undef USE_SONOFF_D1 // Disable support for Sonoff D1 Dimmer (+0k7 code) #undef USE_SHELLY_DIMMER // Disable support for Shelly Dimmer (+3k code) #define USE_LIGHT_PALETTE // Add support for color palette (+0k9 code) #undef USE_EMULATION_WEMO //#undef USE_EMULATION_HUE #define USE_WS2812 #define USE_DS18x20 // Add support for DS18x20 sensors with id sort, single scan and read retry (+1k3 code) #undef USE_ENERGY_SENSOR #define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram) #undef USE_MLX90614 #define USE_SHT // [I2cDriver8] Enable SHT1X sensor (+1k4 code) #define USE_HTU // [I2cDriver9] Enable HTU21/SI7013/SI7020/SI7021 sensor (I2C address 0x40) (+1k5 code) #define USE_BMP // [I2cDriver10] Enable BMP085/BMP180/BMP280/BME280 sensors (I2C addresses 0x76 and 0x77) (+4k4 code) // #define USE_BME68X // Enable support for BME680/BME688 sensor using Bosch BME68x library (+6k9 code) //#define USE_BH1750 // [I2cDriver11] Enable BH1750 sensor (I2C address 0x23 or 0x5C) (+0k5 code) //#define USE_VEML6070 // [I2cDriver12] Enable VEML6070 sensor (I2C addresses 0x38 and 0x39) (+1k5 code) //#define USE_VEML6075 // [I2cDriver49] Enable VEML6075 UVA/UVB/UVINDEX Sensor (I2C address 0x10) (+2k1 code) //#define USE_VEML7700 // [I2cDriver50] Enable VEML7700 Ambient Light sensor (I2C addresses 0x10) (+4k5 code) //#define USE_ADS1115 // [I2cDriver13] Enable ADS1115 16 bit A/D converter (I2C address 0x48, 0x49, 0x4A or 0x4B) based on Adafruit ADS1x15 library (no library needed) (+0k7 code) //#define USE_INA219 // [I2cDriver14] Enable INA219 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+1k code) //#define USE_INA226 // [I2cDriver35] Enable INA226 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+2k3 code) //#define USE_SHT3X // [I2cDriver15] Enable SHT3x (I2C address 0x44 or 0x45) or SHTC3 (I2C address 0x70) sensor (+0k7 code) //#define USE_TSL2561 // [I2cDriver16] Enable TSL2561 sensor (I2C address 0x29, 0x39 or 0x49) using library Joba_Tsl2561 (+2k3 code) //#define USE_TSL2591 // [I2cDriver40] Enable TSL2591 sensor (I2C address 0x29) using library Adafruit_TSL2591 (+1k6 code) //#define USE_MGS // [I2cDriver17] Enable Xadow and Grove Mutichannel Gas sensor using library Multichannel_Gas_Sensor (+10k code) //#define USE_SGP30 // [I2cDriver18] Enable SGP30 sensor (I2C address 0x58) (+1k1 code) //#define USE_SI1145 // [I2cDriver19] Enable SI1145/46/47 sensor (I2C address 0x60) (+1k code) //#define USE_LM75AD // [I2cDriver20] Enable LM75AD sensor (I2C addresses 0x48 - 0x4F) (+0k5 code) //#define USE_APDS9960 // [I2cDriver21] Enable APDS9960 Proximity Sensor (I2C address 0x39). Disables SHT and VEML6070 (+4k7 code) //#define USE_MCP230xx // [I2cDriver22] Enable MCP23008/MCP23017 - Must define I2C Address in #define USE_MCP230xx_ADDR below - range 0x20 - 0x27 (+4k7 code) //#define USE_PCA9685 // [I2cDriver1] Enable PCA9685 I2C HW PWM Driver - Must define I2C Address in #define USE_PCA9685_ADDR below - range 0x40 - 0x47 (+1k4 code) //#define USE_MPR121 // [I2cDriver23] Enable MPR121 controller (I2C addresses 0x5A, 0x5B, 0x5C and 0x5D) in input mode for touch buttons (+1k3 code) //#define USE_CCS811 // [I2cDriver24] Enable CCS811 sensor (I2C address 0x5A) (+2k2 code) //#define USE_CCS811_V2 // [I2cDriver24] Enable CCS811 sensor (I2C addresses 0x5A and 0x5B) (+2k8 code) //#define USE_MPU6050 // [I2cDriver25] Enable MPU6050 sensor (I2C address 0x68 AD0 low or 0x69 AD0 high) (+3K3 of code and 188 Bytes of RAM) //#define USE_MGC3130 // [I2cDriver27] Enable MGC3130 Electric Field Effect Sensor (I2C address 0x42) (+2k7 code, 0k3 mem) //#define USE_MAX44009 // [I2cDriver28] Enable MAX44009 Ambient Light sensor (I2C addresses 0x4A and 0x4B) (+0k8 code) //#define USE_SCD30 // [I2cDriver29] Enable Sensiron SCd30 CO2 sensor (I2C address 0x61) (+3k3 code) //#define USE_SCD40 // [I2cDriver62] Enable Sensiron SCd40 CO2 sensor (I2C address 0x62) (+3k3 code) //#define USE_SPS30 // [I2cDriver30] Enable Sensiron SPS30 particle sensor (I2C address 0x69) (+1.7 code) //#define USE_ADE7953 // [I2cDriver7] Enable ADE7953 Energy monitor as used on Shelly 2.5 (I2C address 0x38) (+1k5) //#define USE_VL53L0X // [I2cDriver31] Enable VL53L0x time of flight sensor (I2C address 0x29) (+4k code) //#define USE_VL53L1X // [I2cDriver54] Enable VL53L1X time of flight sensor (I2C address 0x29) using Pololu VL53L1X library (+2k9 code) //#define USE_TOF10120 // [I2cDriver57] Enable TOF10120 time of flight sensor (I2C address 0x52) (+0k6 code) //#define USE_MLX90614 // [I2cDriver32] Enable MLX90614 ir temp sensor (I2C address 0x5a) (+0.6k code) //#define USE_CHIRP // [I2cDriver33] Enable CHIRP soil moisture sensor (variable I2C address, default 0x20) //#define USE_PAJ7620 // [I2cDriver34] Enable PAJ7620 gesture sensor (I2C address 0x73) (+2.5k code) //#define USE_PCF8574 // [I2cDriver2] Enable PCF8574 I/O Expander (I2C addresses 0x20 - 0x26 and 0x39 - 0x3F) (+1k9 code) //#define USE_HIH6 // [I2cDriver36] Enable Honeywell HIH Humidity and Temperature sensor (I2C address 0x27) (+0k6) //#define USE_DHT12 // [I2cDriver41] Enable DHT12 humidity and temperature sensor (I2C address 0x5C) (+0k7 code) //#define USE_DS1624 // [I2cDriver42] Enable DS1624, DS1621 temperature sensor (I2C addresses 0x48 - 0x4F) (+1k2 code) //#define USE_AHT1x // [I2cDriver43] Enable AHT10/15 humidity and temperature sensor (I2C address 0x38, 0x39) (+0k8 code) //#define USE_AHT2x // [I2cDriver43] Enable AHT20 instead of AHT1x humidity and temperature sensor (I2C address 0x38) (+0k8 code) //#define USE_WEMOS_MOTOR_V1 // [I2cDriver44] Enable Wemos motor driver V1 (I2C addresses 0x2D - 0x30) (+0k7 code) #define WEMOS_MOTOR_V1_ADDR 0x30 // Default I2C address 0x30 #define WEMOS_MOTOR_V1_FREQ 1000 // Default frequency //#define USE_HDC1080 // [I2cDriver45] Enable HDC1080 temperature/humidity sensor (I2C address 0x40) (+1k5 code) //#define USE_IAQ // [I2cDriver46] Enable iAQ-core air quality sensor (I2C address 0x5a) (+0k6 code) //#define USE_AS3935 // [I2cDriver48] Enable AS3935 Franklin Lightning Sensor (I2C address 0x03) (+5k4 code) //#define USE_MCP9808 // [I2cDriver51] Enable MCP9808 temperature sensor (I2C addresses 0x18 - 0x1F) (+0k9 code) //#define USE_HP303B // [I2cDriver52] Enable HP303B temperature and pressure sensor (I2C address 0x76 or 0x77) (+6k2 code) //#define USE_MLX90640 // [I2cDriver53] Enable MLX90640 IR array temperature sensor (I2C address 0x33) (+20k code) //#define USE_EZOPH // [I2cDriver55] Enable support for EZO's pH sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOORP // [I2cDriver55] Enable support for EZO's ORP sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZORTD // [I2cDriver55] Enable support for EZO's RTD sensor (+0k2 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOHUM // [I2cDriver55] Enable support for EZO's HUM sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOEC // [I2cDriver55] Enable support for EZO's EC sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOCO2 // [I2cDriver55] Enable support for EZO's CO2 sensor (+0k2 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOO2 // [I2cDriver55] Enable support for EZO's O2 sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOPRS // [I2cDriver55] Enable support for EZO's PRS sensor (+0k7 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOFLO // [I2cDriver55] Enable support for EZO's FLO sensor (+0k4 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZODO // [I2cDriver55] Enable support for EZO's DO sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZORGB // [I2cDriver55] Enable support for EZO's RGB sensor (+0k5 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOPMP // [I2cDriver55] Enable support for EZO's PMP sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_SEESAW_SOIL // [I2cDriver56] Enable Capacitice Soil Moisture & Temperature Sensor (I2C addresses 0x36 - 0x39) (+1k3 code) //#define USE_MPU_ACCEL // [I2cDriver58] Enable MPU6886/MPU9250 - found in M5Stack - support both I2C buses on ESP32 (I2C address 0x68) (+2k code) //#define USE_AM2320 // [I2cDriver60] Enable AM2320 temperature and humidity Sensor (I2C address 0x5C) (+1k code) //#define USE_T67XX // [I2cDriver61] Enable Telaire T67XX CO2 sensor (I2C address 0x15) (+1k3 code) //#define USE_DS3502 // [I2CDriver67] Enable DS3502 digital potentiometer (I2C address 0x28 - 0x2B) (+0k4 code) //#define USE_HYT // [I2CDriver68] Enable HYTxxx temperature and humidity sensor (I2C address 0x28) (+0k5 code) //#define USE_RTC_CHIPS // Enable RTC chip support and NTP server - Select only one // #define USE_DS3231 // [I2cDriver26] Enable DS3231 RTC (I2C address 0x68) (+1k2 code) // #define USE_BM8563 // [I2cDriver59] Enable BM8563 RTC - found in M5Stack - support both I2C buses on ESP32 (I2C address 0x51) (+2.5k code) // #define USE_PCF85363 // [I2cDriver66] Enable PCF85363 RTC - found Shelly 3EM (I2C address 0x51) (+0k7 code) //#define USE_MHZ19 // Add support for MH-Z19 CO2 sensor (+2k code) //#define USE_SENSEAIR // Add support for SenseAir K30, K70 and S8 CO2 sensor (+2k3 code) //#define USE_CM110x // Add support for CM110x CO2 sensors (+2k7 code) #ifndef CO2_LOW #define CO2_LOW 800 // Below this CO2 value show green light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1) #endif #ifndef CO2_HIGH #define CO2_HIGH 1200 // Above this CO2 value show red light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1) #endif //#define USE_PMS5003 // Add support for PMS5003 and PMS7003 particle concentration sensor (+1k3 code) //#define PMS_MODEL_PMS3003 // Enable support of PMS3003 instead of PMS5003/PMS7003 (needs the USE_PMS5003 above) //#define USE_NOVA_SDS // Add support for SDS011 and SDS021 particle concentration sensor (+0k7 code) //#define USE_HPMA // Add support for Honeywell HPMA115S0 particle concentration sensor //#define USE_SR04 // Add support for HC-SR04 ultrasonic devices (+1k code) //#define USE_DYP // Add support for DYP ME-007 ultrasonic distance sensor, serial port version (+0k5 code) #define USE_SERIAL_BRIDGE // Add support for software Serial Bridge (+0k8 code) //#define USE_MP3_PLAYER // Use of the DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop //#define USE_AZ7798 // Add support for AZ-Instrument 7798 CO2 datalogger //#define USE_PN532_HSU // Add support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem) //#define USE_ZIGBEE // Enable serial communication with Zigbee CC2530 flashed with ZNP //#define USE_RDM6300 // Add support for RDM6300 125kHz RFID Reader (+0k8) #define USE_IR_REMOTE #endif // FIRMWARE_TASMOTA_LVGL ******************************************************************* /*********************************************************************************************\ * [tasmota32-zbbrdgpro] * Provide an image for Sonoff Zigbee Bridge Pro \*********************************************************************************************/ #ifdef FIRMWARE_ZBBRDGPRO #undef CODE_IMAGE_STR #define CODE_IMAGE_STR "zbbrdgpro" #undef MODULE #define MODULE WEMOS // [Module] Select default module from tasmota_template.h #undef FALLBACK_MODULE #define FALLBACK_MODULE WEMOS // [Module2] Select default module on fast reboot where USER_MODULE is user template #undef USE_DOMOTICZ #undef USE_HOME_ASSISTANT #define USE_TASMOTA_DISCOVERY // Enable Tasmota Discovery support (+2k code) #define USE_WEBCLIENT_HTTPS #define USE_ZIGBEE #define USE_TCP_BRIDGE #define USE_ENHANCED_GUI_WIFI_SCAN #undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code) #undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer (+2k code) #undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code) //#define USE_BUZZER // Add support for a buzzer (+0k6 code) #undef USE_ARILUX_RF // Disable support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0)) //#define USE_DEEPSLEEP // Add support for deepsleep (+1k code) #undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer #undef USE_KEELOQ // Disable support for Jarolift rollers by Keeloq algorithm (+4k5 code) #undef USE_SONOFF_D1 // Disable support for Sonoff D1 Dimmer (+0k7 code) #undef USE_SHELLY_DIMMER // Disable support for Shelly Dimmer (+3k code) #define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram) #define USE_SPI // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC) #define USE_ETHERNET // Add support for ethernet (+20k code) //#ifndef USE_KNX //#define USE_KNX // Enable KNX IP Protocol Support (+23k code, +3k3 mem) //#endif #endif // FIRMWARE_ZBBRDGPRO /*********************************************************************************************\ * [tasmota32-nspanel] * Provide an image for ths Sonoff NsPanel \*********************************************************************************************/ #ifdef FIRMWARE_NSPANEL #undef CODE_IMAGE_STR #define CODE_IMAGE_STR "nspanel" #undef MODULE #define MODULE WEMOS // [Module] Select default module from tasmota_template.h #undef FALLBACK_MODULE #define FALLBACK_MODULE WEMOS // [Module2] Select default module on fast reboot where USER_MODULE is user template #define FIRMWARE_TASMOTA32 #endif // FIRMWARE_NSPANEL /*********************************************************************************************\ * [tasmota32.bin] * Provide an image which includes KNX and Sensors \*********************************************************************************************/ #ifdef FIRMWARE_TASMOTA32 #define USE_INFLUXDB // Enable influxdb support (+5k code) #define USE_ENHANCED_GUI_WIFI_SCAN #define USE_SDCARD #define ROTARY_V1 // Add support for Rotary Encoder as used in MI Desk Lamp #define USE_TUYA_MCU // Add support for Tuya Serial MCU #ifndef TUYA_DIMMER_ID #define TUYA_DIMMER_ID 0 // Default dimmer Id #endif #undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code) //#undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer (+2k code) #undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code) #define USE_BUZZER // Add support for a buzzer (+0k6 code) //#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0)) #define USE_DEEPSLEEP // Add support for deepsleep (+1k code) #undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer //#define USE_HOTPLUG // Add support for sensor HotPlug //#undef USE_DEVICE_GROUPS // Disable support for device groups (+5k6 code) //#undef USE_PWM_DIMMER // Disable support for MJ-SD01/acenx/NTONPOWER PWM dimmers (+4k5 code) #undef USE_KEELOQ // Disable support for Jarolift rollers by Keeloq algorithm (+4k5 code) #undef USE_SONOFF_D1 // Disable support for Sonoff D1 Dimmer (+0k7 code) #undef USE_SHELLY_DIMMER // Disable support for Shelly Dimmer (+3k code) #define USE_LIGHT_PALETTE // Add support for color palette (+0k9 code) #define USE_DS18x20 // Add support for DS18x20 sensors with id sort, single scan and read retry (+1k3 code) #define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram) #define USE_SHT // [I2cDriver8] Enable SHT1X sensor (+1k4 code) #define USE_HTU // [I2cDriver9] Enable HTU21/SI7013/SI7020/SI7021 sensor (I2C address 0x40) (+1k5 code) #define USE_BMP // [I2cDriver10] Enable BMP085/BMP180/BMP280/BME280 sensors (I2C addresses 0x76 and 0x77) (+4k4 code) #define USE_BME68X // Enable support for BME680/BME688 sensor using Bosch BME68x library (+6k9 code) #define USE_BH1750 // [I2cDriver11] Enable BH1750 sensor (I2C address 0x23 or 0x5C) (+0k5 code) #define USE_VEML6070 // [I2cDriver12] Enable VEML6070 sensor (I2C addresses 0x38 and 0x39) (+1k5 code) //#define USE_VEML6075 // [I2cDriver49] Enable VEML6075 UVA/UVB/UVINDEX Sensor (I2C address 0x10) (+2k1 code) //#define USE_VEML7700 // [I2cDriver50] Enable VEML7700 Ambient Light sensor (I2C addresses 0x10) (+4k5 code) #define USE_ADS1115 // [I2cDriver13] Enable ADS1115 16 bit A/D converter (I2C address 0x48, 0x49, 0x4A or 0x4B) based on Adafruit ADS1x15 library (no library needed) (+0k7 code) #define USE_INA219 // [I2cDriver14] Enable INA219 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+1k code) //#define USE_INA226 // [I2cDriver35] Enable INA226 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+2k3 code) #define USE_SHT3X // [I2cDriver15] Enable SHT3x (I2C address 0x44 or 0x45) or SHTC3 (I2C address 0x70) sensor (+0k7 code) //#define USE_TSL2561 // [I2cDriver16] Enable TSL2561 sensor (I2C address 0x29, 0x39 or 0x49) using library Joba_Tsl2561 (+2k3 code) //#define USE_TSL2591 // [I2cDriver40] Enable TSL2591 sensor (I2C address 0x29) using library Adafruit_TSL2591 (+1k6 code) #define USE_MGS // [I2cDriver17] Enable Xadow and Grove Mutichannel Gas sensor using library Multichannel_Gas_Sensor (+10k code) #define USE_SGP30 // [I2cDriver18] Enable SGP30 sensor (I2C address 0x58) (+1k1 code) //#define USE_SI1145 // [I2cDriver19] Enable SI1145/46/47 sensor (I2C address 0x60) (+1k code) #define USE_LM75AD // [I2cDriver20] Enable LM75AD sensor (I2C addresses 0x48 - 0x4F) (+0k5 code) //#define USE_APDS9960 // [I2cDriver21] Enable APDS9960 Proximity Sensor (I2C address 0x39). Disables SHT and VEML6070 (+4k7 code) //#define USE_MCP230xx // [I2cDriver22] Enable MCP23008/MCP23017 - Must define I2C Address in #define USE_MCP230xx_ADDR below - range 0x20 - 0x27 (+4k7 code) //#define USE_PCA9685 // [I2cDriver1] Enable PCA9685 I2C HW PWM Driver - Must define I2C Address in #define USE_PCA9685_ADDR below - range 0x40 - 0x47 (+1k4 code) //#define USE_MPR121 // [I2cDriver23] Enable MPR121 controller (I2C addresses 0x5A, 0x5B, 0x5C and 0x5D) in input mode for touch buttons (+1k3 code) //#define USE_CCS811 // [I2cDriver24] Enable CCS811 sensor (I2C address 0x5A) (+2k2 code) #define USE_CCS811_V2 // [I2cDriver24] Enable CCS811 sensor (I2C addresses 0x5A and 0x5B) (+2k8 code) #define USE_MPU_ACCEL // [I2cDriver58] Enable MPU6886, MPU9250 6-axis MotionTracking sensor (I2C address 0x68) //#define USE_MPU6050 // [I2cDriver25] Enable MPU6050 sensor (I2C address 0x68 AD0 low or 0x69 AD0 high) (+3K3 of code and 188 Bytes of RAM) //#define USE_MGC3130 // [I2cDriver27] Enable MGC3130 Electric Field Effect Sensor (I2C address 0x42) (+2k7 code, 0k3 mem) //#define USE_MAX44009 // [I2cDriver28] Enable MAX44009 Ambient Light sensor (I2C addresses 0x4A and 0x4B) (+0k8 code) #define USE_SCD30 // [I2cDriver29] Enable Sensiron SCd30 CO2 sensor (I2C address 0x61) (+3k3 code) #define USE_SCD40 // [I2cDriver62] Enable Sensiron SCd40 CO2 sensor (I2C address 0x62) (+3k5 code) //#define USE_SPS30 // [I2cDriver30] Enable Sensiron SPS30 particle sensor (I2C address 0x69) (+1.7 code) #define USE_ADE7953 // [I2cDriver7] Enable ADE7953 Energy monitor as used on Shelly 2.5 (I2C address 0x38) (+1k5) #define USE_VL53L0X // [I2cDriver31] Enable VL53L0x time of flight sensor (I2C address 0x29) (+4k code) //#define USE_VL53L1X // [I2cDriver54] Enable VL53L1X time of flight sensor (I2C address 0x29) using Pololu VL53L1X library (+2k9 code) //#define USE_TOF10120 // [I2cDriver57] Enable TOF10120 time of flight sensor (I2C address 0x52) (+0k6 code) //#define USE_MLX90614 // [I2cDriver32] Enable MLX90614 ir temp sensor (I2C address 0x5a) (+0.6k code) //#define USE_CHIRP // [I2cDriver33] Enable CHIRP soil moisture sensor (variable I2C address, default 0x20) //#define USE_PAJ7620 // [I2cDriver34] Enable PAJ7620 gesture sensor (I2C address 0x73) (+2.5k code) //#define USE_PCF8574 // [I2cDriver2] Enable PCF8574 I/O Expander (I2C addresses 0x20 - 0x26 and 0x39 - 0x3F) (+1k9 code) #define USE_HIH6 // [I2cDriver36] Enable Honeywell HIH Humidity and Temperature sensor (I2C address 0x27) (+0k6) #define USE_DHT12 // [I2cDriver41] Enable DHT12 humidity and temperature sensor (I2C address 0x5C) (+0k7 code) #define USE_DS1624 // [I2cDriver42] Enable DS1624, DS1621 temperature sensor (I2C addresses 0x48 - 0x4F) (+1k2 code) //#define USE_AHT1x // [I2cDriver43] Enable AHT10/15 humidity and temperature sensor (I2C address 0x38, 0x39) (+0k8 code) //#define USE_AHT2x // [I2cDriver43] Enable AHT20 instead of AHT1x humidity and temperature sensor (I2C address 0x38) (+0k8 code) #define USE_WEMOS_MOTOR_V1 // [I2cDriver44] Enable Wemos motor driver V1 (I2C addresses 0x2D - 0x30) (+0k7 code) #define WEMOS_MOTOR_V1_ADDR 0x30 // Default I2C address 0x30 #define WEMOS_MOTOR_V1_FREQ 1000 // Default frequency //#define USE_HDC1080 // [I2cDriver45] Enable HDC1080 temperature/humidity sensor (I2C address 0x40) (+1k5 code) #define USE_IAQ // [I2cDriver46] Enable iAQ-core air quality sensor (I2C address 0x5a) (+0k6 code) #define USE_AS3935 // [I2cDriver48] Enable AS3935 Franklin Lightning Sensor (I2C address 0x03) (+5k4 code) //#define USE_MCP9808 // [I2cDriver51] Enable MCP9808 temperature sensor (I2C addresses 0x18 - 0x1F) (+0k9 code) //#define USE_HP303B // [I2cDriver52] Enable HP303B temperature and pressure sensor (I2C address 0x76 or 0x77) (+6k2 code) //#define USE_MLX90640 // [I2cDriver53] Enable MLX90640 IR array temperature sensor (I2C address 0x33) (+20k code) //#define USE_EZOPH // [I2cDriver55] Enable support for EZO's pH sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOORP // [I2cDriver55] Enable support for EZO's ORP sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZORTD // [I2cDriver55] Enable support for EZO's RTD sensor (+0k2 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOHUM // [I2cDriver55] Enable support for EZO's HUM sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOEC // [I2cDriver55] Enable support for EZO's EC sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOCO2 // [I2cDriver55] Enable support for EZO's CO2 sensor (+0k2 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOO2 // [I2cDriver55] Enable support for EZO's O2 sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOPRS // [I2cDriver55] Enable support for EZO's PRS sensor (+0k7 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOFLO // [I2cDriver55] Enable support for EZO's FLO sensor (+0k4 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZODO // [I2cDriver55] Enable support for EZO's DO sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZORGB // [I2cDriver55] Enable support for EZO's RGB sensor (+0k5 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_EZOPMP // [I2cDriver55] Enable support for EZO's PMP sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code) //#define USE_SEESAW_SOIL // [I2cDriver56] Enable Capacitice Soil Moisture & Temperature Sensor (I2C addresses 0x36 - 0x39) (+1k3 code) //#define USE_DS3502 // [I2CDriver67] Enable DS3502 digital potentiometer (I2C address 0x28 - 0x2B) (+0k4 code) //#define USE_HYT // [I2CDriver68] Enable HYTxxx temperature and humidity sensor (I2C address 0x28) (+0k5 code) //#define USE_RTC_CHIPS // Enable RTC chip support and NTP server - Select only one // #define USE_DS3231 // [I2cDriver26] Enable DS3231 RTC (I2C address 0x68) (+1k2 code) // #define USE_BM8563 // [I2cDriver59] Enable BM8563 RTC - found in M5Stack - support both I2C buses on ESP32 (I2C address 0x51) (+2.5k code) // #define USE_PCF85363 // [I2cDriver66] Enable PCF85363 RTC - found Shelly 3EM (I2C address 0x51) (+0k7 code) #define USE_SPI // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC) //#define USE_RC522 // Add support for MFRC522 13.56Mhz Rfid reader (+6k code) #define USE_MHZ19 // Add support for MH-Z19 CO2 sensor (+2k code) #define USE_SENSEAIR // Add support for SenseAir K30, K70 and S8 CO2 sensor (+2k3 code) #define USE_CM110x // Add support for CM110x CO2 sensors (+2k7 code) #ifndef CO2_LOW #define CO2_LOW 800 // Below this CO2 value show green light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1) #endif #ifndef CO2_HIGH #define CO2_HIGH 1200 // Above this CO2 value show red light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1) #endif #define USE_PMS5003 // Add support for PMS5003 and PMS7003 particle concentration sensor (+1k3 code) //#define PMS_MODEL_PMS3003 // Enable support of PMS3003 instead of PMS5003/PMS7003 (needs the USE_PMS5003 above) #define USE_NOVA_SDS // Add support for SDS011 and SDS021 particle concentration sensor (+0k7 code) #define USE_HPMA // Add support for Honeywell HPMA115S0 particle concentration sensor #define USE_SR04 // Add support for HC-SR04 ultrasonic devices (+1k code) //#define USE_DYP // Add support for DYP ME-007 ultrasonic distance sensor, serial port version (+0k5 code) #define USE_SERIAL_BRIDGE // Add support for software Serial Bridge (+0k8 code) #define USE_MP3_PLAYER // Use of the DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop //#define USE_AZ7798 // Add support for AZ-Instrument 7798 CO2 datalogger #define USE_PN532_HSU // Add support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem) //#define USE_ZIGBEE // Enable serial communication with Zigbee CC2530 flashed with ZNP #define USE_RDM6300 // Add support for RDM6300 125kHz RFID Reader (+0k8) #define USE_IBEACON // Add support for bluetooth LE passive scan of ibeacon devices (uses HM17 module) //#define USE_GPS // Add support for GPS and NTP Server for becoming Stratus 1 Time Source (+ 3.1kb flash, +132 bytes RAM) //#define USE_BLE_ESP32 // (ESP32 only) Add support for native BLE on ESP32 - use new driver //#define USE_MI_ESP32 // (ESP32 only) Add support for ESP32 as a BLE-bridge (+9k2 mem, +292k flash) #define USE_HRXL // Add support for MaxBotix HRXL-MaxSonar ultrasonic range finders (+0k7) //#define USE_TASMOTA_CLIENT // Add support for Arduino Uno/Pro Mini via serial interface including flashing (+2k3 code, 44 mem) //#define USE_OPENTHERM // Add support for OpenTherm (+15k code) //#define USE_MIEL_HVAC // Add support for Mitsubishi Electric HVAC serial interface (+5k code) //#define USE_PROJECTOR_CTRL // Add support for LCD/DLP Projector serial control interface (+2k code) // #define USE_PROJECTOR_CTRL_NEC // Use codes for NEC // #define USE_PROJECTOR_CTRL_OPTOMA // Use codes for OPTOMA //#define USE_AS608 // Add support for AS608 optical and R503 capacitive fingerprint sensor (+3k4 code) //#define USE_TFMINIPLUS // Add support for TFmini Plus (TFmini, TFmini-S) LiDAR modules via UART interface //#define USE_HRG15 // Add support for Hydreon RG-15 Solid State Rain sensor (+1k5 code) #define USE_ENERGY_SENSOR // Add energy sensors (-14k code) #define USE_PZEM004T // Add support for PZEM004T Energy monitor (+2k code) #define USE_PZEM_AC // Add support for PZEM014,016 Energy monitor (+1k1 code) #define USE_PZEM_DC // Add support for PZEM003,017 Energy monitor (+1k1 code) #define USE_MCP39F501 // Add support for MCP39F501 Energy monitor as used in Shelly 2 (+3k1 code) #define USE_SDM72 // Add support for Eastron SDM72-Modbus energy monitor (+0k3 code) #define USE_SDM120 // Add support for Eastron SDM120-Modbus energy monitor (+1k1 code) #define USE_SDM230 // Add support for Eastron SDM230-Modbus energy monitor (+?? code) #define USE_SDM630 // Add support for Eastron SDM630-Modbus energy monitor (+0k6 code) #define USE_DDS2382 // Add support for Hiking DDS2382 Modbus energy monitor (+0k6 code) #define USE_DDSU666 // Add support for Chint DDSU666 Modbus energy monitor (+0k6 code) //#define USE_SOLAX_X1 // Add support for Solax X1 series Modbus log info (+3k1 code) //#define USE_LE01MR // Add support for F&F LE-01MR modbus energy meter (+2k code) //#define USE_TELEINFO // Add support for French Energy Provider metering telemetry (+5k2 code, +168 RAM + SmartMeter LinkedList Values RAM) //#define USE_WE517 // Add support for Orno WE517-Modbus energy monitor (+1k code) #define USE_SONOFF_SPM // Add support for ESP32 based Sonoff Smart Stackable Power Meter (+11k code) #define USE_DHT // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor #define USE_MAX31855 // Add support for MAX31855 K-Type thermocouple sensor using softSPI //#define USE_MAX31865 // Add support for MAX31865 RTD sensors using softSPI #define USE_IR_REMOTE // Send IR remote commands using library IRremoteESP8266 and ArduinoJson (+4k code, 0k3 mem, 48 iram) #define USE_IR_RECEIVE // Support for IR receiver (+5k5 code, 264 iram) #define USE_LMT01 // Add support for TI LMT01 temperature sensor, count pulses on single GPIO (+0k5 code) //#define USE_WIEGAND // Add support for 24/26/32/34 bit RFID Wiegand interface (D0/D1) (+1k7 code) #define USE_TM1638 // Add support for TM1638 switches copying Switch1 .. Switch8 (+1k code) #define USE_HX711 // Add support for HX711 load cell (+1k5 code) //#define USE_HX711_GUI // Add optional web GUI to HX711 as scale (+1k8 code) //#define USE_TX20_WIND_SENSOR // Add support for La Crosse TX20 anemometer (+2k6/0k8 code) //#define USE_TX23_WIND_SENSOR // Add support for La Crosse TX23 anemometer (+2k7/1k code) //#define USE_WINDMETER // Add support for analog anemometer (+2k2 code) #define USE_RC_SWITCH // Add support for RF transceiver using library RcSwitch (+2k7 code, 460 iram) #define USE_RF_SENSOR // Add support for RF sensor receiver (434MHz or 868MHz) (+0k8 code) // #define USE_THEO_V2 // Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver (+1k4 code) #define USE_ALECTO_V2 // Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 using 868MHz RF sensor receiver (+1k7 code) #define USE_HRE // Add support for Badger HR-E Water Meter (+1k4 code) //#define USE_A4988_STEPPER // Add support for A4988/DRV8825 stepper-motor-driver-circuit (+10k5 code) //#define USE_THERMOSTAT // Add support for Thermostat #define USE_ETHERNET // Add support for ethernet (+20k code) #define USE_DISPLAY_TM1621_SONOFF // Add support for TM1621 display driver used by Sonoff POWR3xxD and THR3xxD #ifndef USE_KNX #define USE_KNX // Enable KNX IP Protocol Support (+23k code, +3k3 mem) #endif #endif // FIRMWARE_TASMOTA32 #endif // ESP32 #endif // _TASMOTA_CONFIGURATIONS_ESP32_H_