/*
sonoff_post.h - Post header file for Sonoff-Tasmota
Copyright (C) 2018 Theo Arends
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see .
*/
#ifndef _SONOFF_POST_H_
#define _SONOFF_POST_H_
/*********************************************************************************************\
* Function declarations
\*********************************************************************************************/
#ifdef __cplusplus
extern "C" {
#endif
#include "user_interface.h"
// Function prototypes
void WifiWpsStatusCallback(wps_cb_status status);
#ifdef __cplusplus
}
#endif
//#ifdef USE_KNX // Enabling this will fail compilation. It has no impact if not used. (20180417)
#include
void KNX_CB_Action(message_t const &msg, void *arg);
//#endif // USE_KNX
/*********************************************************************************************\
* Default global defines
\*********************************************************************************************/
#ifndef MODULE
#define MODULE SONOFF_BASIC // [Module] Select default model
#endif
#define USE_DHT // Default DHT11 sensor needs no external library
#define USE_ENERGY_SENSOR // Use energy sensors
#define USE_HLW8012 // Use energy sensor for Sonoff Pow and WolfBlitz
#define USE_CSE7766 // Use energy sensor for Sonoff S31 and Pow R2
/*********************************************************************************************\
* [sonoff-sensors.bin]
* Provide an image with useful supported sensors enabled
\*********************************************************************************************/
#ifdef USE_SENSORS
#define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices
#define USE_DS18x20 // For more than one DS18x20 sensors with id sort, single scan and read retry (+1k3 code)
//#define USE_DS18x20_LEGACY // For more than one DS18x20 sensors with dynamic scan using library OneWire (+1k5 code)
#define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram)
#define USE_SHT // Add I2C emulating code for SHT1X sensor (+1k4 code)
#define USE_SHT3X // Add I2C code for SHT3x sensor (+0k6 code)
#define USE_HTU // Add I2C code for HTU21/SI7013/SI7020/SI7021 sensor (+1k5 code)
#define USE_LM75AD // Add I2C code for LM75AD sensor (+0k5 code)
#define USE_BMP // Add I2C code for BMP085/BMP180/BMP280/BME280 sensor (+4k code)
#define USE_BME680 // Add additional support for BME680 sensor using Bosch BME680 library (+4k code)
#define USE_SGP30 // Add I2C code for SGP30 sensor (+1k1 code)
#define USE_BH1750 // Add I2C code for BH1750 sensor (+0k5 code)
#define USE_VEML6070 // Add I2C code for VEML6070 sensor (+0k5 code)
#define USE_TSL2561 // Add I2C code for TSL2561 sensor using library Adafruit TSL2561 Arduino (+1k2 code)
//#define USE_SI1145 // Add I2C code for SI1145/46/47 sensor (+1k code)
#define USE_ADS1115 // Add I2C code for ADS1115 16 bit A/D converter based on Adafruit ADS1x15 library (no library needed) (+0k7 code)
//#define USE_ADS1115_I2CDEV // Add I2C code for ADS1115 16 bit A/D converter using library i2cdevlib-Core and i2cdevlib-ADS1115 (+2k code)
#define USE_INA219 // Add I2C code for INA219 Low voltage and current sensor (+1k code)
#define USE_MGS // Add I2C code for Xadow and Grove Mutichannel Gas sensor using library Multichannel_Gas_Sensor (+10k code)
//#define USE_APDS9960 // Add I2C code for APDS9960 Proximity Sensor. Disables SHT and VEML6070 (+4k7 code)
//#define USE_CCS811 // Add I2C code for CCS811 sensor (+2k2 code)
#define USE_MHZ19 // Add support for MH-Z19 CO2 sensor (+2k code)
#define USE_SENSEAIR // Add support for SenseAir K30, K70 and S8 CO2 sensor (+2k3 code)
#ifndef CO2_LOW
#define CO2_LOW 800 // Below this CO2 value show green light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
#endif
#ifndef CO2_HIGH
#define CO2_HIGH 1200 // Above this CO2 value show red light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
#endif
#define USE_PMS5003 // Add support for PMS5003 and PMS7003 particle concentration sensor (+1k3 code)
#define USE_NOVA_SDS // Add support for SDS011 and SDS021 particle concentration sensor (+0k7 code)
#define USE_PZEM004T // Add support for PZEM004T Energy monitor (+2k code)
#define USE_SERIAL_BRIDGE // Add support for software Serial Bridge (+0k8 code)
#define USE_SDM120 // Add support for Eastron SDM120-Modbus energy meter (+1k7 code)
#define USE_SDM630 // Add support for Eastron SDM630-Modbus energy meter (+2k code)
#define USE_IR_REMOTE // Send IR remote commands using library IRremoteESP8266 and ArduinoJson (+4k code, 0k3 mem, 48 iram)
#define USE_IR_HVAC // Support for HVAC system using IR (+2k code)
#define USE_IR_RECEIVE // Support for IR receiver (+5k5 code, 264 iram)
#define USE_WS2812 // WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by //
#ifndef USE_WS2812_CTYPE
#define USE_WS2812_CTYPE NEO_GRB // WS2812 Color type (NEO_RGB, NEO_GRB, NEO_BRG, NEO_RBG, NEO_RGBW, NEO_GRBW)
#endif
// #define USE_WS2812_DMA // DMA supports only GPIO03 (= Serial RXD) (+1k mem). When USE_WS2812_DMA is enabled expect Exceptions on Pow
#define USE_ARILUX_RF // Add support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0))
#define USE_SR04 // Add support for HC-SR04 ultrasonic devices (+1k code)
#endif // USE_SENSORS
/*********************************************************************************************\
* [sonoff-classic.bin]
* Provide an image close to version 5.12.0 but still within 499k program space to allow one time OTA
\*********************************************************************************************/
#ifdef USE_CLASSIC
#ifndef USE_WPS
#define USE_WPS // Add support for WPS as initial wifi configuration tool (+33k code, 1k mem (5k mem with core v2.4.2+))
#endif
#ifndef USE_SMARTCONFIG
#define USE_SMARTCONFIG // Add support for Wifi SmartConfig as initial wifi configuration tool (+23k code, +0.6k mem)
#endif
#undef MQTT_LIBRARY_TYPE
#define MQTT_LIBRARY_TYPE MQTT_PUBSUBCLIENT // Use PubSubClient library
#undef USE_ARDUINO_OTA // Disable support for Arduino OTA
#undef USE_KNX // Disable KNX IP Protocol Support
#undef USE_TIMERS // Disable support for up to 16 timers
#undef USE_TIMERS_WEB // Disable support for timer webpage
#undef USE_SUNRISE // Disable support for Sunrise and sunset tools
#undef USE_RULES // Disable support for rules
#undef USE_I2C // Disable all I2C sensors
#undef USE_SPI // Disable all SPI devices
#undef USE_MHZ19 // Disable support for MH-Z19 CO2 sensor
#undef USE_SENSEAIR // Disable support for SenseAir K30, K70 and S8 CO2 sensor
#undef USE_PMS5003 // Disable support for PMS5003 and PMS7003 particle concentration sensor
#undef USE_NOVA_SDS // Disable support for SDS011 and SDS021 particle concentration sensor
#undef USE_PZEM004T // Disable PZEM004T energy sensor
#undef USE_PZEM2 // Disable PZEM003,014,016,017 Energy monitor
#undef USE_SERIAL_BRIDGE // Disable support for software Serial Bridge
#undef USE_SDM120 // Disable support for Eastron SDM120-Modbus energy meter
#undef USE_SDM630 // Disable support for Eastron SDM630-Modbus energy meter
#undef USE_IR_REMOTE // Disable IR remote commands using library IRremoteESP8266 and ArduinoJson
#undef USE_IR_RECEIVE // Disable support for IR receiver
#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller
#undef USE_SR04 // Disable support for for HC-SR04 ultrasonic devices
#undef USE_TM1638 // Disable support for TM1638 switches copying Switch1 .. Switch8
#undef USE_RF_FLASH // Disable support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // USE_CLASSIC
/*********************************************************************************************\
* [sonoff-knx.bin]
* Provide a dedicated KNX image allowing enough code and memory space
\*********************************************************************************************/
#ifdef USE_KNX_NO_EMULATION
#ifndef USE_KNX
#define USE_KNX // Enable KNX IP Protocol Support (+23k code, +3k3 mem)
#endif
#undef USE_EMULATION // Disable Belkin WeMo and Hue Bridge emulation for Alexa (-16k code, -2k mem)
#endif // USE_KNX_NO_EMULATION
/*********************************************************************************************\
* Mandatory define for DS18x20 if changed by above image selections
\*********************************************************************************************/
#if defined(USE_DS18x20) || defined(USE_DS18x20_LEGACY)
#else
#define USE_DS18B20 // Default DS18B20 sensor needs no external library
#endif
/*********************************************************************************************\
* [sonoff-minimal.bin]
* Provide the smallest image possible while still enabling a webserver for intermediate image load
\*********************************************************************************************/
#ifdef BE_MINIMAL
#undef USE_ENERGY_SENSOR // Disable energy sensors
#undef USE_ARDUINO_OTA // Disable support for Arduino OTA
#undef USE_WPS // Disable support for WPS as initial wifi configuration tool
#undef USE_SMARTCONFIG // Disable support for Wifi SmartConfig as initial wifi configuration tool
#undef USE_DOMOTICZ // Disable Domoticz
#undef USE_HOME_ASSISTANT // Disable Home Assistant
#undef USE_MQTT_TLS // Disable TLS support won't work as the MQTTHost is not set
#undef USE_KNX // Disable KNX IP Protocol Support
//#undef USE_WEBSERVER // Disable Webserver
#undef USE_DISCOVERY // Disable Discovery services for both MQTT and web server
#undef USE_EMULATION // Disable Wemo or Hue emulation
#undef USE_TIMERS // Disable support for up to 16 timers
#undef USE_TIMERS_WEB // Disable support for timer webpage
#undef USE_SUNRISE // Disable support for Sunrise and sunset tools
#undef USE_RULES // Disable support for rules
#undef USE_DHT // Disable internal DHT sensor
#undef USE_DS18x20 // Disable DS18x20 sensor
#undef USE_DS18x20_LEGACY // Disable DS18x20 sensor
#undef USE_DS18B20 // Disable internal DS18B20 sensor
#undef USE_I2C // Disable all I2C sensors and devices
#undef USE_SPI // Disable all SPI devices
#undef USE_DISPLAY // Disable Display support
#undef USE_MHZ19 // Disable support for MH-Z19 CO2 sensor
#undef USE_SENSEAIR // Disable support for SenseAir K30, K70 and S8 CO2 sensor
#undef USE_PMS5003 // Disable support for PMS5003 and PMS7003 particle concentration sensor
#undef USE_NOVA_SDS // Disable support for SDS011 and SDS021 particle concentration sensor
#undef USE_PZEM004T // Disable PZEM004T energy sensor
#undef USE_SERIAL_BRIDGE // Disable support for software Serial Bridge
#undef USE_SDM120 // Disable support for Eastron SDM120-Modbus energy meter
#undef USE_SDM630 // Disable support for Eastron SDM630-Modbus energy meter
#undef USE_IR_REMOTE // Disable IR driver
#undef USE_WS2812 // Disable WS2812 Led string
#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller
#undef USE_SR04 // Disable support for for HC-SR04 ultrasonic devices
#undef USE_TM1638 // Disable support for TM1638 switches copying Switch1 .. Switch8
#undef USE_RF_FLASH // Disable support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // BE_MINIMAL
/*********************************************************************************************\
* Mandatory defines satisfying possible disabled defines
\*********************************************************************************************/
#ifndef USE_WPS // See https://github.com/esp8266/Arduino/pull/4889
#undef NO_EXTRA_4K_HEAP // Allocate 4k heap for WPS in ESP8166/Arduino core v2.4.2 (was always allocated in previous versions)
#endif
#ifndef SWITCH_MODE
#define SWITCH_MODE TOGGLE // TOGGLE, FOLLOW or FOLLOW_INV (the wall switch state)
#endif
#ifndef MQTT_FINGERPRINT1
#define MQTT_FINGERPRINT1 "A5 02 FF 13 99 9F 8B 39 8E F1 83 4F 11 23 65 0B 32 36 FC 07"
#endif
#ifndef MQTT_FINGERPRINT2
#define MQTT_FINGERPRINT2 "A5 02 FF 13 99 9F 8B 39 8E F1 83 4F 11 23 65 0B 32 36 FC 07"
#endif
#ifndef WS2812_LEDS
#define WS2812_LEDS 30 // [Pixels] Number of LEDs
#endif
#ifndef MQTT_MAX_PACKET_SIZE
#define MQTT_MAX_PACKET_SIZE 1000
#endif
#ifndef MQTT_KEEPALIVE
#define MQTT_KEEPALIVE 15
#endif
#ifndef MESSZ
//#define MESSZ 405 // Max number of characters in JSON message string (6 x DS18x20 sensors)
//#define MESSZ 893 // Max number of characters in JSON message string (Hass discovery and nice MQTT_MAX_PACKET_SIZE = 1000)
#define MESSZ (MQTT_MAX_PACKET_SIZE -TOPSZ -7) // Max number of characters in JSON message string (6 x DS18x20 sensors)
#endif
//#include // Arduino_Esp8266 version information (ARDUINO_ESP8266_RELEASE and ARDUINO_ESP8266_RELEASE_2_3_0)
#ifndef ARDUINO_ESP8266_RELEASE
#define ARDUINO_ESP8266_RELEASE "STAGE"
#endif
#endif // _SONOFF_POST_H_