/*********************************************************************************************\ * 6.6.0.5 20190816 * Add command WebSensor 0/1 to control display of sensor data in web GUI (#6085) * Change some table locations from RAM to Flash * Fix wrong telemetry message when SetOption68 1 (#6191) * * 6.6.0.4 20190806 * Add support for CHIRP soil moisture sensor by Christian Baars * Add debug compile features using defines DEBUG_TASMOTA_CORE, DEBUG_TASMOTA_DRIVER and DEBUG_TASMOTA_SENSOR. * See DEBUG_CORE_LOG example in sonoff.ino and DEBUG_DRIVER_LOG example in xdrv_09_timers.ino * Add support for Solax X1 inverter by Pablo Zerón * Add ZigBee support phase 1 - low level MQTT ZNP messages for CC2530 devices * Add command Buzzer with optional parameters ,, enabled when a buzzer is configured (#5988) * Add support for PAJ7620 gesture sensor by Christian Baars * * 6.6.0.3 20190725 * Change filename of configuration backup from using FriendlyName1 to Hostname solving diacritic issues (#2422) * Change Store AWS IoT Private Key and Certificate in SPI Flash avoiding device-specific compilations * Upgrade library IRRemoteEsp8266 to 2.6.4, now using sendPioneer() * Add support for MAX31865 Thermocouple sensor by Alberto Lopez Siemens * Add option 0 to Width1 (Marker), Width2 (Second), Width3 (Minute) and Width4 (Hour) disabling display (#6152) * Add MqttCount metric to STATE (#6155) * Add define USE_ENERGY_MARGIN_DETECTION to disable Energy Margin and Power Limit detection * Add define USE_ENERGY_POWER_LIMIT to disable Energy Power Limit detection while Energy Margin detection is active * Add allow repeat/longpress for IRSend raw, introduced IRSend option (#6074) * Add SetOption68 to enable multi-channel PWM instead of a single light (#6134) * * 6.6.0.2 20190714 * Change commands Var and Mem to show all parameters when no index is given (#6107) * Add command SetOption67 0/1 to disable or enable a buzzer as used in iFan03 * Add command DisplayWidth to set pixel width on supported devices * Add command DisplayHeight to set pixel height on supported devices * Add support for Sonoff iFan03 as module 71 (#5988) * Add support for a buzzer * Add support for IRSend long press ('repeat' feature from IRRemoteESP8266) (#6074) * Add support for IRHVAC Midea/Komeco protocol (#3227) * Add support for more IRSend protocols enabled in my_user_config.h * Add support for IRSend Pioneer protocol (#6100) * Add Oled reset GPIO option "OLED reset" * * 6.6.0.1 20190708 * Fix Domoticz battery level set to 100 if define USE_ADC_VCC is not used (#6033) * Fix Force Elliptic Curve for Letsencrypt TLS #6042 * Fix WeMo emulation for 1G echo and 2G echo dot (#6086) * Fix Xiaomi Philips brightness (#6091) * Change defines USE_TX20_WIND_SENSOR and USE_RC_SWITCH in my_user_config.h to disable to lower iram usage enabling latest core compilation (#6060, #6062) * Add blend RGB leds with White leds for better whites (#5895, #5704) * Add command SetOption41 0..8 to control number of Tuya switches (#6039) * Add command SetOption42 0..255 to set overtemperature (Celsius only) threshold resulting in power off all on energy monitoring devices. Default setting is 90 (#6036) * Add command SetOption66 0/1 to enable or disable Tuya dimmer range 255 slider control * Add command Time to disable NTP and set UTC time as Epoch value if above 1451602800 (=20160101). Time 0 re-enables NTP (#5279) * Add AZ7798 automatic setting of clock display (#6034) * Add Epoch and UptimeSec to JSON messages (#6068) * Add support for up to 4 INA219 sensors (#6046) * * 6.6.0 20190707 * Remove support of TLS on core 2.3.0 and extent support on core 2.4.2 and up * Remove MQTT uptime message every hour * Refactor some defines to const * Refactor webserver HTML input, button, textarea, and select name based on id * Refactor webserver sensor data collection * Refactor TLS based on BearSSL, warning breaking change for fingerprints validation * Refactor management of lights, using classes and integers instead of floats * Refactor UDP initial message handling from string to char using static memory and add debug info (#5505) * Refactor IRSend and receive for 64-bit support (#5523) * Refactor MQTT which might solve issue (#5755) * Refactor IRSend by using heap when more than 199 values need to be send. May need increase of define MQTT_MAX_PACKET_SIZE too (#5950) * Refactor double to float in rules, and replaced trigonometric functions from stdlib with smaller versions (#6005) * Change pubsubclient MQTT_KEEPALIVE from 10 to 30 seconds for AWS IoT support * Change gamma correction as default behavior, ie "Ledtable 1" * Change PWM resolution from 8 to 10 bits for low brightness lights * Change IRSend Panasonic protocol to 64-bit (#5523) * Change ADC0 to enabled by default in my_user_config.h (#5671) * Change define USE_EMULATION by USE_EMULATION_HUE and USE_EMULATION_WEMO (#5826) * Change default PowerDelta from 80% to 0% on new installations (#5858, #5028, #4813, #4130, #4145, #3795, #3778, #3660, #3648) * Fix display Bug in KNX webmenu for Physical Address * Fix the Unescape() function and the SendSerial3 behaviour * Fix webserver multiple Javascript window.onload functionality * Fix TasmotaSerial at 9600 bps solving DFPlayer comms (#5528) * Fix Configure Timer Web GUI (#5568) * Fix Shelly 2.5 I2C address priority issue when VEML6070 code is present by disabling VEML6070 for Shelly 2.5 (#5592) * Fix use of SerialDelimiter value 128 (#5634) * Fix Sonoff Pow R2 / S31 invalid energy increments (#5789) * Fix core 2.5.x ISR not in IRAM exception (#5837) * Fix Philips Hue emulation Alexa issue by using part of MAC address for LightId (#5849) * Fix missing white channel for WS2812 (#5869) * Fix PZem startup issue (#5875) * Fix exception 9 when syslog is enabled and NTP is just synced (#5917) * Fix Toggle functionality to button double press when one button and two devices are detected (#5935) * Fix channel command for dual dimmers (#5940) * Fix not restoring white value on power off/power on (#5993) * Add command AdcParam to control ADC0 Temperature and Light formula parameters * Add command LedMask to assign which relay has access to power LED (#5602, #5612) * Add extended LED power control using command LedPowerX where X is 1 to 4. Enabled when "LedLink(i)" is configured too (#5709) * Add command Sensor20 1..255 to change Nova Fitness SDS01 working period in minutes (#5452) * Add command SetOption38 6..255 to set IRReceive protocol detection sensitivity mimizing UNKNOWN protocols (#5853) * Add command SetOption39 1..255 to control CSE7766 (Pow R2) or HLW8032 (Blitzwolf SHP5) handling of power loads below 6W. Default setting is 128 (#5756) * Add command SetOption40 0..250 to disable button functionality if activated for over 0.1 second. Needs SetOption1 1 and SetOption13 0 (#5449) * Add command SetOption63 0/1 to disable relay state feedback scan at restart (#5594, #5663) * Add command SetOption64 0/1 to switch between "-" or "_" as sensor index separator impacting DS18X20, DHT, BMP and SHT3X sensor names (#5689) * Add command SetOption65 0/1 and more Tuya Serial based device support (#5815) * Add command WebColor to change GUI colors on the fly * Add support for AWS IoT with TLS 1.2 on core 2.4.2 and up. Full doc here: https://github.com/arendst/Sonoff-Tasmota/wiki/AWS-IoT * Add support for Badger HR-E Water Meter (#5539) * Add support for Shelly 2.5 Energy and overtemp Monitoring (#5592) * Add support for color and colortone for Philips Hue emulation via Alexa (#5600 #4809) * Add support for Scripts as replacement for Rules. Default disabled but can be enabled in my_user_config.h (#5689) * Add support for up to four LEDs related to four power outputs. Enabled when "LedLink(i)" is configured too (#5709) * Add support for Shelly 1PM Template {"NAME":"Shelly 1PM","GPIO":[56,0,0,0,82,134,0,0,0,0,0,21,0],"FLAG":2,"BASE":18} (#5716) * Add support for SPS30 Particle sensor thanks to Gerhard Mutz (#5830) * Add support for VL53L0x time of flight sensor. Might interfere with TSL2561 using same I2C address (#5845) * Add support for Sonoff L1 thanks to reef-actor (#6002) * Add rule Http#Initialized * Add rule System#Save executed just before a planned restart * Add rule support for single JSON value pair like {"SSerialReceived":"on"} by expanding it to {"SSerialReceived":{"Data":"on"}} allowing for trigger SSerialReceived#Data=on (#5638) * Add define USE_COUNTER to my_user_config.h to save space in sonoff-basic.bin and sonoff-minimal.bin * Add define USE_DHT to my_user_config.h to save space in sonoff-basic.bin * Add defines USE_EMULATION_WEMO and USE_EMULATION_HUE to my_user_config.h to control emulation features at compile time (#5826) * Add Toggle functionality to button double press when more devices are detected * Add device OverTemp (>73 Celsius) detection to Energy Monitoring devices with temperature sensor powering off all outputs * Add Tuya Dimmer 10 second heartbeat serial packet required by some Tuya dimmer secondary MCUs * Add all temperature, humidity and pressure for global access * Add validation check when loading settings from flash * Add HX711 weight restore after controlled restart or after power restore just before executing command Sensor34 7 (#5367, #5786) * Add GUI hexadecimal color options in my_user_config.h (#5586) * Add alternative IRSend command syntax IRSend raw,,
,
,,,, (#5610) * Add user configurable ADC0 to Module and Template configuration compatible with current FLAG options (#5671) * Add AriLux RF control GPIO option "ALux IrSel" (159) replacing "Led4i" (59) for full LED control (#5709) * Add LED GPIO option "LedLink" (157) and "LedLinki" (158) to select dedicated link status LED (#5709) * Add all 5 PWM channels individually adressable with LEDs. (#5741) * Add reset of Energy values when connection to sensor is lost for over 4 seconds (#5874, #5881) * Add checkbox to GUI password field enabling visibility during password entry only (#5934) * * 6.5.0 20190319 * Remove commands SetOption14 and SetOption63 as it has been superseded by command Interlock * Remove command SetOption35 0-255 for mDNS start-up delay (#4793) * Remove support for MQTT_LIBRARY_TYPE, MQTT_ARDUINOMQTT and MQTT_TASMOTAMQTT (#5474) * Change webserver content handling from single String to small Chunks increasing RAM * Change code use of boolean to bool and byte to uint8_t * Change code uint8_t flags to bool flags * Change sonoff_template.h layout regarding optional module flags like ADC0 * Change sonoff_template.h module lay-out by removing non-configurable GPIOs * Change button driver making it modular * Change switch driver making it modular and introduce input filter (#4665, #4724) * Change switch input detection by optimizing switch debounce (#4724) * Change web authentication (#4865) * Change image name BE_MINIMAL to FIRMWARE_MINIMAL and USE_xyz to FIRMWARE_xyz (#5106) * Change GUI weblog from XML to plain text solving possible empty screens (#5154) * Fix most compiler warnings * Fix Display exception 28 when JSON value is nullptr received * Fix epaper driver (#4785) * Fix HAss Sensor Discovery Software Watchdog restart (#4831, #4988) * Fix allowable MAX_RULE_VARS to 16 (#4933) * Fix mDNS addService (#4938, #4951) * Fix HAss discovery of MHZ19(B) sensors (#4992) * Fix some exceptions and watchdogs due to lack of stack space (#5215) * Fix GUI wifi password acception starting with asteriks (*) (#5231, #5242) * Fix command WebSend intermittent results (#5273, #5304) * Fix additional characters in fallbacktopic, hostname and mqttclient on core 2.5.0 (#5359, #5417) * Fix Energy TotalStartTime when commands EnergyReset0 and/or EnergyReset3 used (#5373) * Fix DS18S20 temperature calculation (#5375) * Fix float calculations in range from 0 to -1 (#5386) * Fix exception on GUI Configure Logging and Configure Other (#5424) * Add commands PowerCal, VoltageCal and CurrentCal for HLW8012, HJL01 and BL0937 based energy sensors * Add command SerialDelimiter 128 to filter reception of only characters between ASCII 32 and 127 (#5131) * Add command SSerialSend5 \ to SerialBridge * Add command Interlock 0 / 1 / 1,2 3,4 .. to control interlock ON/OFF and add up to 8 relays in 1 to 4 interlock groups (#4910, #5014) * Add command Template 255 to copy module configuration over to current active template and store as user template named Merged (#5371) * Add command WifiConfig 7 to allow reset of device in AP mode without admin password (#5297) * Add command SetOption36 to control boot loop default restoration (#4645, #5063) * Add command SetOption37 for RGBCW color mapping (#5326) * Add command SetOption55 0/1 and define MDNS_ENABLE to disable/enable mDNS (#4793, #4923) * Add command SetOption62 0/1 to disable retain on Button or Switch hold messages (#5299) * Add support for Smanergy KA10 Smart Wall Socket with Energy monitoring * Add support for commands in sensor drivers * Add support for MAX31855 K-Type thermocouple sensor using softSPI (#4764) * Add support for Near Field Communication (NFC) controller PN532 using Serial (#4791, #5162) * Add support for OBI Power Socket 2 (#4829) * Add support for YTF IR Bridge (#4855) * Add support for Mi LED Desk Lamp with rotary switch (#4887) * Add support for Digoo DG-SP202 Smart Socket with Energy monitoring (#4891) * Add support for MAX44009 Ambient Light sensor (#4907) * Add support for inverted buttons and inverted buttons without pullup (#4914) * Add support for Luminea ZX2820 Smart Socket with Energy monitoring (#4921) * Add support for multiple ADS1115 I2C devices (#5083) * Add support for online template change using command Template or GUI Configure Other (#5177) * Add support for Korean language translations (#5344) * Add support for sensor SCD30 (#5434) * Add parameter CFG_HOLDER to status 1 message (#5206) * Add SetOption32 until SetOption49 diagnostic information to Status 3 report as replacement for second property value in SetOption property name * Add Resolution property to Status 3 report providing previous SetOption second value property * Add property MqttCount to status 6 message representing number of Mqtt re-connections * Add property LinkCount to state and status 11 message representing number of Wifi Link re-connections * Add property Downtime to state and status 11 message representing the duration of wifi connection loss * Add variable %timestamp% to rules (#4749) * Add rule support for "==", "!=" ">=" and "<=" (#5122) * Add rule expression enabled by define USE_EXPRESSION in my_user_config.h (#5210) * Add Power status functionality to LED2 when configured leaving LED1 for Link status indication * Add user configuration of HLW8012 and HJL-01/BL0937 Energy Monitoring as used in Sonoff Pow and many Tuya based devices * Add user configuration of MCP39F501 Energy Monitoring as used in Shelly2 * Add online template configuration using both commands and Configure Template menu option in GUI * Add (S)SerialSend3 escape sequence \x to allow hexadecimal byte value (#3560, #4947) * Add define DS18B20_INTERNAL_PULLUP to select internal input pullup when only one DS18B20 sensor is connected eliminating external resistor (#4738) * Add button control when no relay configured (#4682) * Add startup delay of 4 seconds to button control (#4829) * Add core version conditional compile options to provided PWM files (#4917) * Add resiliency to saved Settings (#5065) * Add MHZ19 Temperature as Domoticz Temperature selection (#5128) * Add HAss status sensor (#5139) * Add status message to former declined group commands (#5145) * Add 0x to IRRemote (SetOption29) and RCSwitch (SetOption28) received hexadecimal data (#5431) * * 6.4.1 20181224 * Change RAM usage BMP/BME I2C sensors * Change FallbackTopic from cmnd// to cmnd/_fb/ to discriminate from Topic (#1528) * Change FallbackTopic detection (#4706) * Change Hass discovery to short MQTT messages as used by Hass 0.81 and up (#4711) * Change MQTT GUI password handling (#4723) * Fix possible dtostrf buffer overflows by increasing buffers * Fix wifi strongest signal detection (#4704) * Fix Alexa "this value is outside the range of the device". Needs power cycle and Alexa deletion/discovery cycle. (#3159, #4712) * Add Slovak language file (#4663) * Add support for AZ-Instrument 7798 CO2 meter/datalogger (#4672) * Add define WIFI_SOFT_AP_CHANNEL in my_user_config.h to set Soft Access Point Channel number between 1 and 13 as used by Wifi Manager web GUI (#4673) * Add define USE_MQTT_TLS_CA_CERT for checking MQTT TLS against root ca using Let's Encrypt cert from sonoff_letsencrypt.h - not supported with core 2.3.0 (#4703) * * 6.4.0 20181217 * Change GUI Configure Module by using AJAX for data fetch to cut page size (and memory use) by 40% In case of web page errors clear your browser cache or do Page Reload (F5 or Ctrl+R) * Change enforcing flashmode dout but it is still mandatory * Change bootcount update (being first) flash write to 10 seconds after restart * Change display and epaper drivers * Change command WebSend Host header field from IP address to hostname (#4331) * Change log buffer size from 512 to 520 to accommodate http sensor data (#4354) * Change default WIFI_CONFIG_TOOL from WIFI_WAIT to WIFI_RETRY in my_user_config.h (#4400) * Change webgui refresh time delay for Save Settings and local OTA Upload (#4423) * Change SR-04 driver to use NewPing library (#4488) * Change MCP230xx driver to support interrupt retention over teleperiod (#4547) * Change support for MPU6050 using DMP (#4581) * Fix unintended function overload of WifiState * Fix wifi connection errors using wifi disconnect and ESP.reset instead of ESP.restart * Fix Sonoff Pow R2 and Sonoff S31 Serial interface hang caused by Sonoff Basic R2 driver delay implementation (and possibly core bug) * Fix MQTT connection error after restart * Fix wifi re-scan connection baseline * Fix possible strncat buffer overflows * Fix intermittent Pzem sensor energy overflow calculation error * Fix shelly2 ghost switching caused by lack of pull-up inputs (#4255) * Fix hardware serial pin configuration. To keep using hardware serial swap current Rx/Tx pin configuration only (#4280) * Fix MqttRetry values above 255 seconds (#4424) * Fix WifiManager functionality on initial installation (#4433) * Fix ArduinoOTA for Core 2.5.0 (#4620) * Add minutes to commands Timezone to allow all possible world timezones * Add more strict checks for GPIO selections * Add code image and optional commit number to version * Add dynamic delay to main loop providing time for wifi background tasks * Add additional start-up delay during initial wifi connection * Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver * Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver * Add user definition of defines WIFI_RSSI_THRESHOLD (default 10) and WIFI_RESCAN_MINUTES (default 44) * Add command SetOption58 0/1 to enable IR raw data info in JSON message (#2116) * Add command IRSend |0,,,.. to allow raw data transmission (#2116) * Add command SetOption56 0/1 to enable wifi network scan and select highest RSSI (#3173) * Add command SetOption57 0/1 to enable wifi network re-scan every 44 minutes with a rssi threshold of 10 to select highest RSSI (#3173) * Add support for SDM220 (#3610) * Add default sleep 1 to sonoff-basic to lower energy consumption (#4217) * Add wifi status to Tuya (#4221) * Add delays to reduce CPU usage at boot time (#4233) * Add command SetOption24 0/1 to select pressure unit as hPa or mmHg (#4241) * Add optional hardware serial when GPIO13(Rx) and GPIO15(Tx) are selected removing hardware serial from GPIO01(Tx) and GPIO03(Rx) (#4288) * Add support for Gosund SP1 v2.3 Power Socket with Energy Monitoring (#4297) * Add support for Armtronix dimmers. See wiki for info (#4321) * Add to command WebSend option to send a direct path when command starts with a slash (#4329) * Add support for LG HVac and IrRemote (#4377) * Add initial support for Hass sensor discovery (#4380) * Add support for Fujitsu HVac and IrRemote (#4387) * Add support for I2C MGC3130 Electric Field Effect sensor by Christian Baars (#3774, #4404) * Add command CalcRes to set number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE (#4420) * Add CPU average load to state message (#4431) * Add command SetOption59 0/1 to change state topic from tele/STATE to stat/RESULT (#4450) * Add support for SM Smart Wifi Dimmer PS-16-DZ (#4465) * Add support for Teckin US Power Socket with Energy Monitoring (#4481) * Add command SetOption60 0/1 to select dynamic sleep (0) or sleep (1) (#4497) * Add support for iFan02 Fanspeed in Domoticz using a selector (#4517) * Add support for GPIO02 for newer Sonoff Basic (#4518) * Add Announce Switches to MQTT Discovery (#4531) * Add support for Manzoku Power Strip (#4590) * * 6.3.0 20181030 * Change web Configure Module GPIO drop down list order for better readability * Change status JSON message providing more switch and retain information * Change xsns_17_senseair.ino to use TasmotaModbus library * Change MCP230xx driver * Change PubSubClient Mqtt library to non-blocking EspEasy version * Change energy monitoring using energy sensor driver modules * Change Webserver page handler for easier extension (thx to Adrian Scillato) * Change pinmode for no-pullup defined switches to pullup when configured as switchmode PUSHBUTTON (=3 and up) (#3896) * Change default OTA Url to http://thehackbox.org/tasmota/release/sonoff.bin (#4170) * Remove support for MQTT Client esp-mqtt-arduino by #define MQTT_LIBRARY_TYPE MQTT_ESPMQTTARDUINO * Remove commands PowerCal, VoltageCal and CurrentCal as more functionality is provided by commands PowerSet, VoltageSet and CurrentSet * Remove restart after ntpserver change and force NTP re-sync (#3890) * Fix showing Period Power in energy threshold messages * Fix header file execution order by renaming user_config.h to my_user_config.h * Fix some TSL2561 driver issues (#3681) * Fix KNX PA exception. Regression from 6.2.1 buffer overflow caused by subStr() (#3700, #3710) * Fix setting and getting color temperature for Philips Hue emulation (#3733) * Fix ButtonRetain to not use default topic for clearing retain messages (#3737) * Fix syslog when emulation is selected (#2109, #3784) * Fix rule trigger POWER1#STATE execution after restart and SetOption0 is 0 (#3856) * Fix Home Assistant forced light discovery (#3908) * Fix invalid configuration restores and decode_config.py crc error when savedata = 0 (#3918) * Fix timer offset -00:00 causing 12:00 hour offset (#3923) * Fix I2CScan invalid JSON error message (#3925) * Fix exception when wrong Domoticz JSON message is received (#3963) * Fix Sonoff Bridge RfRaw receive (#4080, #4085) * Fix possible wifi connection error (#4044, #4083) * Fix invalid JSON floating point result from nan (Not a Number) and inf (Infinity) into null (#4147) * Fix rule mqtt#connected trigger when mqtt is disabled (#4149) * Add support for LCD, Matrix, TFT and Oled displays * Add support for Neo Coolcam Wifi Smart Power Plug * Add support for Michael Haustein ESP Switch * Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT * Add support for Neo Coolcam Wifi Smart Power Plug * Add support for Michael Haustein ESP Switch * Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT * Add support for DS3231 Real Time Clock * Add support for HX711 Load Cell with optional web GUI scale interface to demonstrate easy GUI plug-in * Add support for serial 8N2 communication to TasmotaModbus and TasmotaSerial libraries * Add support for RF transceiving using library RcSwitch (#2702) * Add support for Shelly 1 and Shelly 2 (#2789) * Add support for La Crosse TX20 Anemometer (#2654, #3146) * Add support for MP3 player using DFRobot RB-DFR-562 (#3723) * Add Support for Xiaomi-Philips Bulbs (#3787) * Add support for PCA9685 12bit 16pin hardware PWM driver (#3866) * Add support for EXS Relay V5.0 (#3810) * Add support for OBI Power Socket (#1988, #3944) * Add support for Teckin Power Socket with Energy Monitoring (#3950) * Add support for Pzem-003/017 DC Energy monitoring module (#3694) * Add support for Pzem-014/016 AC Energy monitoring module (#3694) * Add support for CSL Aplic WDP 303075 Power Socket with Energy Monitoring (#3991, #3996) * Add support for Tuya Dimmer (#469, #4075) * Add command Display to show all settings at once * Add command SerialSend5 to send raw serial data like "A5074100545293" * Add command WebRefresh 1000..10000 to control web page refresh in milliseconds. Default is 2345 * Add command WeightRes 0..3 to control display of decimals for kilogram * Add command RGBWWTable to support color calibration (#3933) * Add command Reset 4 (reset to defaults but keep wifi params) and Reset 5 (as reset 4 and also erase flash) (#4061) * Add command SetOption35 0..255 (seconds) to delay mDNS initialization to control possible Wifi connect problems * Add command SetOption52 0/1 to control display of optional time offset from UTC in JSON messages (#3629, #3711) * Add command SetOption53 0/1 to toggle gui display of Hostname and IP address (#1006, #2091) * Add authentication to HTTP web pages * Add decimals as input to commands PowerSet, VoltageSet and CurrentSet * Add tools/decode-config.py by Norbert Richter to decode configuration data. See file for information * Add define USE_DISPLAYS for selecting image sonoff-display * Add define USE_BASIC for selecting image sonoff-basic without most sensors * Add auto reload of main web page to some web restarts * Add TasmotaModbus library as very basic modbus wrapper for TasmotaSerial * Add more API callbacks and document API.md * Add Apparent Power and Reactive Power to Energy Monitoring devices (#251) * Add token %hostname% to command FullTopic (#3018) * Add Wifi channel number to state message (#3664) * Add user configurable GPIO02 and GPIO03 on H801 devices (#3692) * Add toggle function RGBW lights (#3695, #3697) * Add network information to display start screen (#3704) * Add sleep to Nova Fitness SDS01X sensor (#2841, #3724, #3749) * Add Analog input AD0 enabled to sonoff-sensors.bin (#3756, #3757) * Add power value below 5W to Sonoff Pow R2 and S31 (#3745) * Add RF Receiver control to module MagicHome to be used on Arilux LC10 (#3792) * Add userid/password option to decode-status.py (#3796) * Add delay after restart before processing rule sensor data (#3811) * Add force_update to Home Assistant discovery (#3873) * Add rule triggers SWITCH1#BOOT and POWER1#BOOT (#3904, #3910) * Add Hebrew language file (#3960) * Add TotalStartTime to Energy JSON message (#3971) * Add whitespace removal from RfRaw and SerialSend5 (#4020) * Add support for two BMP/BME sensors (#4195) * * 6.2.1 20180905 * Fix possible ambiguity on command parameters if StateText contains numbers only (#3656) * Fix Wemo emulation to select the first relay when more than one relay is present (#3657) * Fix possible exception due to buffer overflow (#3659) * Fix lost energy today and total energy value after power cycle (#3689) * * 6.2.0 20180901 * Allow user override of define MAX_RULE_VARS and MAX_RULE_TIMERS (#3561) * Disable wifi sleep for both Esp8266/Arduino core 2.4.1 and 2.4.2 to solve device freeze caused by Espressif SDK bug (#3554) * Change DS18B20 driver to provide better instant results * Change some sensor drivers to provide instant results * Change define USE_ALL_SENSORS to USE_SENSORS as it doesn't contain all sensors due to duplicate I2C addresses * Change some sensor update timings: AdcEvery 200 -> 250, Senseair 300 -> 250, SDM120 300 -> 250, SDM630 300 -> 250 * Change default Wifi config option from WPS to Wifi Manager if WPS is disabled or Wifi Smartconfig if webserver is disabled or Wifi Serial input if Smartconfig is disabled * Change SHT1x driver to provide better instant results and fix I2C interference * Change DHT driver to provide better instant results and add decimals to DHT11 (#3164) * Change DS18x20 driver to provide better instant results (#3169) * Change CounterType 1 from milliseconds to microseconds (#3437) * Change scheduler for better sleep support using Uptime, Delay, PulseTime and TelePeriod, Blinktime (#3581) * Remove unused functionality from Sonoff-minimal to save space * Remove WPS and SmartConfig from sonoff-minimal saving 56k code space * Remove TSL2561 debug message and update library (#2415) * Remove forced restart when sleep command is executed (#3554) * Fix invalid response using more than 4 switches and domoticz * Fix sonoff-minimal not using default settings * Fix unsecure main webpage update * Fix DHT driver mixing values for different sensors (#1797) * Fix EnergyReset3 regression not clearing total energy (#2723) * Fix rules once regression from v6.1.0 (#3198, #3226) * Fix command Scale buffer overflow (#3236) * Fix possible WDT due to long MQTT publish handling (#3313) * Fix command TimeDst/TimeStd invalid JSON (#3322) * Fix handling of default names when using names starting with shortcut character ",0,1 or 2 (#3392, #3600, #3618) * Fix LM75AD I2C sensor detection (#3408) * Fix iFan02 power on state (#3412, #3530) * Fix some Pow R2 and S31 checksum errors using optimized re-sync (#3425) * Fix SDM120 reporting wrong negative values to Domoticz (#3521) * Fix MQTT reconnection detection when using TasmotaMqtt library (#3558) * Fix OtaMagic when file path contains a dash (-) (#3563) * Fix Sonoff Bridge data reception when using Portisch EFM8 firmware using in data buffer length (#3605) * Add read sensor retry to DS18B20, DS18x20, DHT, SHT1X and HTU21 * Add user selection of Wifi Smartconfig as define USE_SMARTCONFIG in user_config.h * Add boot loop detection and perform some solutions * Add wifi and mqtt status led blinkyblinky to be disabled by SetOption31 1. Does not work when LedPower is On (deliberate) (#871, #2230, #3114, #3155) * Add support for TM1638 switch (#2226) * Add GPIO options ButtonXn, SwitchXn and CounterXn to select INPUT mode instead of INPUT_PULLUP (#2525) * Add support for APDS9960 proximity sensor (#3051) * Add support for MPR121 controller in input mode for touch buttons (#3142) * Add support for MCP230xx for general purpose input expansion and command Sensor29 (#3188) * Add default Wifi Configuration tool as define WIFI_CONFIG_NO_SSID in user_config.h if no SSID is configured (#3224) * Add command Timers 0/1 to globally disable or enable armed timers (#3270) * Add support for CCS811 sensor (#3309) * Add Turkish language file (#3332) * Add command SerialSend4 to send binary serial data (#3345) * Add initial support for sensor MPU6050 (#3352) * Add rule triggers Wifi#Connected and Wifi#Disconnected (#3359) * Add option + to command Rule to concatenate new rule with existing rules (#3365) * Add message when JavaScript is not enabled in webbrowser (#3388) * Add build time setting of ButtonTopic and SwitchTopic (#3414) * Add iFan02 Fanspeed + and Fanspeed - command options (#3415) * Add Individual HSBColorX commands (#3430, #3615) * Add output support on MCP23008/MCP23017 (#3436) * Add modulo option to rules like rule1 on Time#Minute|5 do backlog power on;delay 200;power off endon (#3466) * Add RGB support for Domoticz (#3547) * Add all ruletimer values to command RuleTimer result message (#3571) * Add command Publish2 for publishing retained MQTT messages (#3593) * Add commands ButtonDebounce 40..1000 and SwitchDebounce 40..1000 to have user control over debounce timing. Default is 50mS (#3594) * Add RuleX debug options 8,9,10 (StopOnError) to control RuleX execution status after an exception restart (#3607) * Add rule variables %sunrise%, %sunset%, %uptime% and %time% (#3608) * Add optional MQTT_TELE_RETAIN to Energy Margins message (#3612, 3614) * * 6.1.1 20180714 * Revert wifi changes (#3177) * Revert sonoff-minimal removals causing failure of wifi connection (#3177) * * 6.1.0 20180706 * Remove version 3, 4 and pre 5.2 settings auto-upgrade. See https://github.com/arendst/Sonoff-Tasmota/wiki/Upgrade#migration-path * Change default CFG_HOLDER from 0x20161209 to 4617 (=0x1209) - no impact on default upgrades * Change number of supported switches from 4 to 8 (#2885, #3086) * Change BME680 driver from Adafruit to Bosch BME680 library (#2969) * Fix Pzem004T checksum error * Fix KNX bug when doing reply of sensors values * Fix rules induced LWT message * Fix possible wifi connection problem (#1366) * Fix some Pow R2 and S31 checksum errors (#1907) * Fix display selection of un-available GPIO options in Module Configuration webpage (#2718) * Fix timer re-trigger within one minute after restart (#2744) * Fix IRSend not accepting data value of 0 by David Conran (#2751) * Fix vars on rules by Adrian Scillato (#2769) * Fix bug in KNX menu by Adrian Scillato (#2770) * Fix anomalies in rules (#2778) * Fix HUE bridge V1 software version by Heiko Krupp (#2788) * Fix Hardware Watchdog restart when using event command (#2853) * Add Ukrainian language file * Add KNX support for DS18S20 Temperature sensor * Add CRC to Settings making future upgrades more fail-safe * Add feature information to Status 4 * Add tools folder with python script decode-status.py for decoding some status fields like SetOption and Features * Add Slots on the KNX Web Menu to select Group Addess to receive data to trigger rules * Add two rule sets of 511 characters using commands rule1, rule2 and rule3 * Add Console Commands to send KNX Commands and KNX Values * Add Slots on the KNX Web Menu to select Group Addess to send data from console commands * Add Events to trigger rules when a command or read requests is received from KNX * Add command SetOption30 to enforce Hass discovery as light group (#1784) * Add support for BlitzWolf BW-SHP2 (and Homecube, Gosund SP1) Energy Monitoring Smart Socket (#2223) * Add time in minutes to rule Time#Initialized, Time#set and Time#Minute (#2669) * Add Eastron SDM630 energy meter by Gennaro Tortone (#2735) * Add KNX communication enhancement by Adrian Scillato (#2742) * Add KNX energy data by Adrian Scillato (#2750) * Add rule support for IrReceive and RfReceive (#2758) * Add python script fw-server.py in tools folder to create a simple OTA server by Gennaro Tortone (#2759) * Add rule variables %time% for minutes since midnight, %uptime%, %sunrise% and %sunset% giving time in minutes (#2669) * Add rules %mem1% to %mem5% variable names storing data in flash (#2780) * Add rules test on %varx% or %memx% (#2780) * Add optional token %id% substituting the unique MAC address to fulltopic by Michael Graf (#2794) * Add support for Sonoff S26 Smart Socket (#2808) * Add command WebSend [(:,:)] (#2821) * Add increment and decrement value to command Counter (#2838) * Add support for Sonoff iFan02 as module 44 introducing command FanSpeed 0..3 (#2839) * Add source information to command execution to be shown with logging option 3 (#2843) * Add support for uploading Sonoff Bridge firmware found in tools/fw_efm8bb1 folder build by Portisch using Web Gui File Upload (#2886) * Add command RfRaw to control Portisch firmware features * Add support for I2C temperature sensor LM75AD (#2909) * Add option 0 to command Timers disarming all timers (#2962) * Add performance improvement when updating multiple individual WS2812 pixels (#3007) * Add command SetOption28 to switch between hex or decimal Sonoff Bridge RF received data format (#3008) * Add command SetOption29 to switch between hex or decimal IR received data format * Add decimal values support for commands ADD, SUB, MULT and SCALE (#3083, #3089) * Add support for bitflags SetOption50 .. SetOption81 (#3118) * * 5.14.0 20180515 * Update language files * Update TasmotaSerial to 2.0.0 allowing Hardware Serial Fallback when correct connections are configured * Change command handling * Change user_config(_override).h defines TIME_STD and TIME_DST * Change user_config(_override).h otaurl to http://sonoff.maddox.co.uk/tasmota/sonoff.bin (#2588, #2602) * Fix configuration restore regression from 5.13.1 * Fix compile error when ADC is enabled and Rules are disabled (#2608) * Fix rule power trigger when no backlog command is used (#2613) * Fix several timer data input and output errors (#2597, #2620) * Fix KNX config error (#2628) * Fix sensor MHZ-19 vanishing data over time (#2659) * Fix KNX reconnection issue (#2679) * Fix DST and STD time for Southern Hemisphere by Adrian Scillato (#2684, #2714) * Add Portuguese in Brazil language file * Add SetOption26 to enforce use of indexes even when only one relay is present (#1055) * Add support for sensor SI1145 UV Index / IR / Visible light (#2496) * Add rule state test for On/Off in addition to 0/1 (#2613) * Add hardware serial option to MHZ-19 sensor (#2659) * Add Eastron SDM120 energy meter by Gennaro Tortone (#2694) * Add user entry DST/STD using commands TimeStd and TimeDst (See wiki for parameter syntax) (#2721) * * 5.13.1 20180501 * Fix JSON buffers size too small for execution in some situations (#2580) * Fix configuration restore (#2591) * Add define MODULE for user selecting default model although it preferably should not be changed (#569, #2589) * * 5.13.0 20180430 * Change platformio option sonoff-ds18x20 to sonoff-allsensors enabling ds18x20 and all other sensors in one image * Change status display of Ssid and SetOption * Change default option SetOption15 from 0 to 1 providing better initial PWM experience * Change webpage parameter communication * Change max number of commands in Backlog from 15 to 30 and ignore commands overflowing * Change TSL2561 driver to joba library and delete Adafruit library (#1644) * Change default parameters in user_config.h to undefined for easy installation (#1851) * Change max user configurable hold time from 10 to 25 seconds (#1851) * Change Sonoff SC JSON format (#1939) * Change Polish language to using Diacritics (#2005) * Change user_config_override usage by providing user_config_override_sample.h (#2228) * Change MQTT response topic for Energy changes from ENERGY to SENSOR (#2229, #2251) * Change default Reset configuration time from 4 seconds to 40 seconds on Button hold (#2268) * Change ESP8266 Analog JSON message from {"Analog0:123"} to {"ANALOG":{"A0:123"}} to accomodate rules (#2560) * Change Counter JSON message from {"Counter1":0,"Counter3":0} to {"COUNTER":{"C1":0,"C3":0}} to accomodate rules * Change ADS1115 JSON message from {"ADS1115":{"Analog0":123,"Analog1":123}} to {"ADS1115":{"A0":123,"A1":123}} * Fix intermittent exception when dns lookup is used while sleep is enabled * Fix 5.4.0 regression turning off single press after button hold during 4x hold time * Fix possible wifi connection problem by erasing sdk configuration parameters * Fix NTP sync to Thu Jan 01 08:00:10 1970 results in uptime 17651+ days (core2.4.1/sdk2.2.1) * Fix MAX31850 higher temperatures (#1269) * Fix freeing more code space when emulation is disabled (#1592) * Fix providing web page configuratin option for Friendly Name when no device (relay or light) is configured (#1850) * Fix compile error when define HOME_ASSISTANT_DISCOVERY_ENABLE is not set (#1937) * Fix MQTT TLS fingerprint validation (#2033) * Fix update temperature on DS18x20 drivers (#2328) * Fix compile error when not defined USE_TIMERS (#2400) * Fix configuration filename truncation when it contains spaces (#2484, #2490) * Fix Energy Today and Yesterday overflow (#2543) * Add serial debug info * Add Portuguese language file * Add Czech language file * Add Bulgarian language file * Add Domoticz dust (custom) sensors to PMS5003 and NovaFitness SDS drivers as PM1, PM2.5 and PM10 * Add commands Publish, Rule, RuleTimer and Event. See Wiki about Rule restriction, usage and examples * Add sonoff-classic, sonoff-allsensors and sonoff-knx * Add some coloring to important web buttons * Add support for sensor HC-SR04 ultrasonic (#113, #1964, #2444) * Add define MQTT_TELE_RETAIN compile option default set to 0 (#1071) * Add 16 timers using commands Timer and Timers (#1091) * Add optional Timer configuration webpage to be enabled in user_config.h with define USE_TIMERS_WEB * Add Multichannel Gas sensor using MultiChannel_Gas_Sensor library (#1245) * Add Domoticz Battery and RSSI Quality (#1604) * Add command HSBColor Hue,Sat,Bri (#1642, #2203) * Add compile time support for WS2812 BRG and RBG led configurations to be defined in user_config.h (#1690) * Add optional usage of %d or %X suffices in MQTT client to append chipid (#1871) * Add optional usage of %d or %X suffices in MQTT topic to append chipid (#1871) * Add optional usage of %d or %04d in ota url to be replaced with chipid (#1871) * Add Sonoff Bridge command RfKey 5 to show current RF key values either default or learned (#1884) * Add user configurable serial GPIOs to MagicHome and Arilux modules (#1887) * Add Russian language file (#1909) * Add Webserver upload preflight request support (#1927) * Add Home Assistant clear other device (#1931) * Add Restart time to Status 1 (#1938) * Add optional TSL2561 driver using library Joba_Tsl2561 to be enabled in user_config.h with define USE_TSL2561_JOBA (#1951) * Add support for sensor SHTC3 (#1967) * Add compiler check for stable lwIP version v1.4 (#1940) * Add support for multiple SHT3X sensors (#1949, #2110) * Add always suffix with device number in Mqtt discovery topic (#1962) * Add support for optional MQTT drivers to be selected in user_config.h (#1992) * Add optional Arduino OTA support to be enabled in user_config.h (#1998) * Add diacritics to Polish language file (#2005) * Add Hungarian language file (#2024) * Add support for Nova Fitness SDS011 and possibly SDS021 particle concentration sensor (#2070) * Add single decimal precision to Nova Fitness SDS0x1 sensor values (#2093) * Add Chinese (Traditional) in Taiwan language file (#2108) * Add Sonoff SC domoticz support for Sound level as Counter and Air quality (#2118) * Add a second TLS fingerprint to allow switching keys in TLS mode (#2033, #2102) * Add display of remaining pulse time to command PulseTime (#2085) * Add additional time offset to Wifi Retry based on device mac address (#2089) * Add command Color6 RRGGBB for Clock hour marker color and command Rotation pixels for Clock rotation (#2092) * Add HTML language header in local language (#2123) * Add command PowerDelta 0..100 (percentage) to Energy monitoring devices to report on active power load change (#2157) * Add Restart Reason to Status 1 report (#2161) * Add command Channel 0..100 to control dimmer value for individual color channels (#2111, #2203) * Add support for Hardware Serial bridge using commands SerialDelimiter, Baudrate and SerialSend. Supports 8N1 and text only (#2182) * Add support for Software Serial bridge using commands SerialDelimiter, SBaudrate and SSerialSend. Supports 8N1 and text only (#2190) * Add support for Zengge WF017 PWM Led strip controller (#2202) * Add PWM status to command State if PWM enabled (#2203) * Add all FriendlyNames to Status information (#2208) * Add Channel status information (#2211) * Add hexadecimal Data entry to command IrSend using 0x notation (#1290, #2314) * Add Home Assistant MQTT Discovery for Buttons and change SetOption19 response (#2277) * Add multiple color entry support for command Led like Led2 120000 001200 000012 setting led2 as Red, Led3 as Green and Led4 as Blue (#2303) * Add hexadecimal RGB color entry on RGBCW leds (#2304) * Add support for SGP30 gas and air quality sensor (#2307) * Add optional Sunrise and Sunset timers with commands Latitide and Longitude to be enabled with define USE_SUNRISE in user_config.h (#2317) * Add timer sunrise and sunset offset (#2378) * Add user selectable defines for Sunrise/set Dawn option (#2378) * Add optional KNX IP Protocol Support (#2402) * Add random window to timers (#2447) * Add Greek language file (#2491) * Add support for Sonoff Pow R2 (#2340) * Add GPIO_User to GPIO02 for all Sonoff T1 (#2524) * * 5.12.0 20180209 * Change library PubSubClient.h define MQTT_MAX_PACKET_SIZE from 512 to 1000 for Home Assistant support * Change relation of define MESSZ being dependent on PubSubClient.h define MQTT_MAX_PACKET_SIZE * Change command color parameter input checks to less strict for Home Assistant support * Change command Ina219Mode into command Sensor13 * Change commands HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to be used for both Pow and S31 calibration * Change commands HlwPSet, HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used for both Pow and S31 calibration * Change uptime from hour to second resulting in a display of 123T13:45:21 where 123 is days * Change module name Wemos D1 mini into Generic (#1220) * Change HTML from width=100% to style=width:100% supporting HTML5 (#1358) * Change OSWATCH_RESET_TIME (Blocked loop) from 30 to 120 seconds to allow slow networks (#1556) * Change WIFI_MANAGER_SEC into WIFI_CONFIG_SEC (#1616) * Change function pointers code to save code space and memory (#1683) * Change webserver argument processing gaining 5k code space (#1705) * Change weblog memory usage (#1730, #1793, #1819) * Update TasmotaSerial library to 1.1.0 * Update language files Italian (#1594), Dutch (#1723) and Spanish (#1722) * Fix Non-English JSON temperature unit attachement * Fix Arilux RF induced exception by moving interrupt handler to iram on non ESP8266/Arduino lib v2.3.0 * Fix truncated command names and wrong response for DomoticzSwitchIdx (#1571) * Fix %-sign issue as printf escape character in Humidity and Sonoff SC (#1579) * Fix DS18B20 temperature JSON decimal dot (#1561) * Fix Energy JSON message (#1621) * Fix IRSend parameter translation (#1636) * Fix TSL2561 device detection (#1644, #1825) * Fix BME680 teleperiod resistance measuring (#1647) * Fix Energy Monitoring Energy Today and Energy Total reading after restart (#1648) * Fix IRReceive Data value (#1663) * Fix Energy Monitoring Energy Period roll-over (#1688) * Fix compiler warnings (#1774) * Fix command PWM response if no PWM channel is configured (#1783) * Add locale Decimal Separator to Web sensor page * Add ColorTemperature to light status message * Add command PowerOnState option 5 which inverts PulseTime and allows for delayed always on after power on * Add OtaMagic two step Web server OTA upgrade using filename-minimal image if OTA free space is too small * Add support for PMS5003 and PMS7003 particle concentration sensor * Add command SetOption21 1 to allow Energy Monitoring when power is off on Sonoff Pow and Sonoff S31 (#1420) * Add Chinese language file (#1551) * Add French language file (#1561) * Add Spanish language file (#1589) * Add HTTP Allow Cross Origin removed from ESP8266/Arduino lib v2.4.0 (#1572) * Add Home Assistant MQTT Discovery for switch and light to be enabled by command SetOption19 1 (#1534) or define HOME_ASSISTANT_DISCOVERY_ENABLE in user_config.h (#1685) * Add command State to retrieve device state information (same data as teleperiod state and status 11 in slightly different JSON format) * Add optional login to Webserver AP mode (#1587, #1635) * Add command Sensor15 2 to start MHZ19(B) Zero Point Calibration (#1643) * Add support for Sonoff S31 Smart Socket with Power Consumption Detection (#1626) * Add command SetOption20 to allow update of Dimmer/Color/Ct without turning power on (#1719, #1741) * Add NTP sync time slot based on chip id (#1773) * Add cursor pointer to web button (#1836) * * 5.11.1 20180107 * Fix Sonoff Pow command handling (#1542) * * 5.11.0 20180107 * Minor webpage HTML optimizations (#1358) * Updated German translation (#1438) * Change Sonoff Pow Energy MQTT data message and consolidate Status 8 into Status 10 * Change ADS1115 default voltage range from +/-2V to +/-6V (#1289) * Change text to Active for 3 minutes (#1364) * Change Wemo SetBinaryState to distinguish from GetBinaryState (#1357) * Change output of HTTP command to valid JSON and Array only (#1363) * Removed all MQTT, JSON and Command language defines from locale files and set fixed to English (#1473) * Renamed commands Color2,3,4 to Color3,4,5 * Fix BME280 calculation (#1051) * Fix Sonoff Bridge missed learned key if learned data contains 0x55 (End of Transmission) flag (#1095, #1294) * Fix PWM initialization in Dimmer/Color mode (#1321) * Fix Wemo Emulation (#1357) * Fix display of build date and time in non-english locale (#1465) * Fix Wemo and Hue emulation by adding M-Search response delay (#1486) * Add libraries Adafruit_BME680-1.0.5, Adafruit_Sensor-1.0.2.02, TasmotaSerial-1.0.0 and TSL2561-Arduino-Library * Add command Color2 to set color while keeping same dimmer value * Add device function pointers * Add support for SenseAir S8 CO2 sensor * Add color led signal to Carbon Dioxide (CO2) sensors using defines CO2_LOW and CO2_HIGH in user_config.h * Add support for Domoticz Air Quality sensor to be used by MH-Z19(B) and SenseAir sensors * Add support for PZEM004T energy sensor * Add support for iTead SI7021 temperature and humidity sensor by consolidating DHT22 into AM2301 and using former DHT22 as SI7021 (#735) * Add support for BME680 using adafruit libraries (#1212) * Add support for MH-Z19(B) CO2 sensor (#561, #1248) * Add multipress support and more user configurable GPIO to Sonoff Dual R2 (#1291) * Add support for TSL2561 using adafruit library (#661, #1311) * Add support for SHT3x (#1314) * Add support for Arilux LC06 (#1414) * Add Italian language file (#1449) * Add 2nd Gen Alexa support to Wemo emulation discovery (#1357, #1450) * Add define for additional number of WS2812 schemes (#1463) * * 5.10.0 20171201 * Upgrade library ArduinoJson to 5.11.2 * Upgrade library IRRemoteEsp8266 to 2.2.1 + 2 commits but disabled some protocols (code size reduction) * Upgrade library NeoPixelBus to 2.2.9 * Upgrade library OneWire to 2.3.3 + 6 commits and disabled CRC lookup-table (#define ONEWIRE_CRC8_TABLE 0) (code size reduction) * Update library PubSubClient to 2.6 + 9 commits and additional delay (#790) * Update core_esp8266_wiring_digital.c to latest (staged) level * Patch library I2Cdevlib-Core for esp8266-core 2.4.0-rc2 compatibility * Remove command EnergyReset 1..3 now replaced by EnergyReset1 to EnergyReset3 * Remove spaces in JSON messages (code size reduction) * Renamed xsns_05_ds18x20.ino to xsns_05_ds18x20_legacy.ino still using library OneWire and providing dynamic sensor scan * Fix possible iram1_0_seg compile error by shrinking ICACHE_RAM_ATTR code usage * Fix PWM watchdog timeout if Dimmer is set to 100 or Color set to 0xFF (#1146) * Fix Sonoff Bridge Learn Mode hang caused by unrecognised RF code (#1181) * Fix blank console log window by using XML character encoding (#1187) * Fix wrong response name for command HlwISet (#1214) * Fix DHT type sensor timeout recognition by distinguish "signal already there" from "timeout" (#1233) * Add fixed color options 1..12 to command Color * Add + (plus) and - (minus) to commands Dimmer (+10/-10), Speed and Scheme * Add + (plus) and - (minus) to command Color to select 1 out of 12 preset colors * Add + (plus) and - (minus) to command Ct to control ColdWarm led ColorTemperature (+34/-34) * Add commands EnergyReset1 0..42500, EnergyReset2 0..42500 and EnergyReset3 0..42500000 * to (Re)set Energy Today, Yesterday or Total respectively in Wh (#406, #685, #1202) * Add optional ADS1115 driver as alternative for unsupported I2Cdevlib in esp8266-core 2.4.0-rc2 * Add support for INA219 Voltage and Current sensor to be enabled in user_config.h with define USE_INA219 * Add support for Arilux LC11 (Clearing RF home code when selecting no Arilux module) * Add support for WS2812 RGBW ledstrips to be enabled in user_config.h with define USE_WS2812_CTYPE (#1156) * Add SettingsSaveAll routine to command SaveData to be used before controlled power down (#1202) * Add option PUSHBUTTON_TOGGLE (SwitchMode 7) to allow toggling on any switch change (#1221) * Add new xdrv_05_ds18x20.ino free from library OneWire and add the following features: * Add support for DS1822 * Add forced setting of 12-bit resolution for selected device types (#1222) * Add read temperature retry counter (#1215) * Fix lost sensors by performing sensor probe at restart only thereby removing dynamic sensor probe (#1215) * Fix sensor address sorting using ascending sort on sensor type followed by sensor address * Rewrite JSON resulting in shorter message allowing more sensors in default firmware image: * "DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6} * Add additional define in user_config.h to select either single sensor (defines disabled), new multi sensor (USE_DS18X20) or legacy multi sensor (USE_DS18X20_LEGACY) * Add clock support for more different pixel counts (#1226) * Add support for Sonoff Dual R2 (#1249) * Add FriendlyName to web page tab and add program information to web page footer (#1275) * * 5.9.1 20171107 * Add external sensor function pointer interface to enable easy sensor addition * Add support for ADS1115 to be enabled in user_config.h and needs libraries i2cdevlib-Core and i2cdevlib-ADS1115 (#338, #660) * Fix Backup Configuration file download failure by defining proper file size (#1115) * Fix Exception 26 and empty console screen after usage of command WakeupDuration (#1133) * Fix some changed iTead web links in README.md (#1137) * * 5.9.0 20171030 * Rewrite code (partly) using Google C++ Style Guide (https://google.github.io/styleguide/cppguide.html) * Rewrite code by using command lookup tables and javascript (client side) web page expansions * Change HTML/CSS to enable nicer form field entry * Change default PWM assignments for H801 RGB(CW) led controller to support optional Color/Dimmer control * GPIO04 (W2) from GPIO_PWM2 to GPIO_USER to be user configurable for GPIO_PWM5 (second White - Warm if W1 is Cold) * GPIO12 (Blue) GPIO_PWM3 no change * GPIO13 (Green) from GPIO_PWM4 to GPIO_PWM2 * GPIO14 (W1) from GPIO_PWM1 to GPIO_USER to be user configurable for GPIO_PWM4 (first White - Cold or Warm) * GPIO15 (Red) from GPIO_PWM5 to GPIO_PWM1 * Change default PWM assignments for MagicHome RGB(W) led controller to support optional Color/Dimmer control * GPIO05 (Green) from GPIO_PWM4 to GPIO_PWM2 * GPIO12 (Blue) from GPIO_PWM5 to GPIO_PWM3 * GPIO13 (White) GPIO_USER to be user configurable for GPIO_PWM4 (White - Cold or Warm) * GPIO14 (Red) from GPIO_PWM3 to GPIO_PWM1 * Change default PWM assignment for Witty Cloud to support optional Color/Dimmer control (#976) * GPIO12 (Green) from GPIO_PWM4 to GPIO_PWM2 * GPIO13 (Blue) from GPIO_PWM5 to GPIO_PWM3 * GPIO15 (Red) from GPIO_PWM3 to GPIO_PWM1 * Change when another module is selected now all GPIO user configuration is removed * Change command name IRRemote to IRSend (#956) * Remove Arduino IDE version too low warning as it interferes with platformio.ini platform = espressif8266_stage * Fix command FullTopic entry when using serial or console interface * Fix possible UDP syslog blocking * Fix minimum TelePeriod of 10 seconds set by web page * Fix command GPIOx JSON response (#897) * Fix inverted relay power on state (#909) * Fix compile error when DOMOTICZ_UPDATE_TIMER is not defined (#930) * Fix alignment of web page items in some browsers (#935) * Fix setting all saved power settings to Off when SetOption0 (SaveState) = 0 (#955) * Fix timezone range from -12/12 to -13/13 (#968) * Fix Southern Hemisphere TIME_STD/TIME_DST (#968) * Fix TLS MQTT SSL fingerprint test (#970, #808) * Fix virtual relay status message used with Color/Dimmer control (#989) * Fix command IRSend and IRHvac case sensitive parameter regression introduced with version 5.8.0 (#993) * Fix pressure calculation for some BMP versions regression introduced with version 5.8.0i (#974) * Fix Domoticz Dimmer set to same level not powering on (#945) * Fix Blocked Loop when erasing large flash using command reset 2 (#1002) * Fix relay power control when light power control is also configured as regression from 5.8.0 (#1016) * Fix Mqtt server mDNS lookup only when MqttHost name is empty (#1026) * Add debug information to MQTT subscribe * Add translations to I2Cscan * Add translation to BH1750 unit lx * Add light scheme options (Color cycle Up, Down, Random) and moving WS2812 schemes up by 3 * Add Domoticz counter sensor to IrReceive representing Received IR Protocol and Data * Add option 0 to MqttHost to allow empty Mqtt host name * Add support for Arilux AL-LC01 RGB Led controller (#370) * Add esp8266 de-blocking to PubSubClient library (#790) * Add Domoticz sensors for Voltage and Current (#903) * Add platformio OTA upload support (#928, #934) * Add warning to webpage when USE_MINIMAL is selected (#929) * Add smoother movement of hour hand in WS2812 led clock (#936) * Add support for Magic Home RGBW and some Arilux Led controllers (#940) * Add command SetOption15 0 (default) for command PWM control or SetOption15 1 for commands Color/Dimmer control to PWM RGB(CW) leds (#941) * Add Domoticz counter sensor to Sonoff Bridge representing Received RF code (#943) * Add support for Luani HVIO board (https://luani.de/projekte/esp8266-hvio/) (#953) * Add PWM initialization after restart (#955) * Add IR Receiver support. Disable in user_config.h (#956) * Add support for inverted PWM (#960) * Add Sea level pressure calculation and Provide command Altitude (#974) * Add support for up to 8 relays (#995) * Add commands RfSync, RfLow, RfHigh, RfHost and RfCode to allow sending custom RF codes (#1001) * Add retain to ENERGY messages controlled by command SensorRetain (#1013) * Add commands Color2, Color3, Color4, Width2, Width3, Width4 and SetOption16 to set Ws2812 Clock parameters (#1019) * Add German language file (#1022) * Add support for connecting to MQTT brokers without userid and/or password (#1023) * Add support for esp8266 core v2.4.0-rc2 (#1024) * Add commands PwmRange 1,255..1023 and PwmFrequency 1,100..4000 (#1025) * Add Polish language file (#1044, #1047) * Add support for KMC 70011 Power Monitoring Smart Plug (#1045) * Add support for VEML6070 I2C Ultra Violet level sensor (#1053) * Add light turn Off Fade (#925) * Add IrSend command option Panasonic as IrSend {"Protocol":"Panasonic", "Bits":16388, "Data":} * where 16388 is 0x4004 hexadecimal (#1014) * Add retry counter to DHT11/21/22 sensors (#1082) * * 5.8.0 20170918 * Remove the need for NeoPixelBus library for Hue support * Consolidate WS2812 into Sonoff Led for flexible future led strip library changes * Invert WS2812 fade speed to align with Sonoff led (Speed 1 = fast, Speed 8 = slow) * Remove upper case MQTT receive buffer * Reduce code and string length for output of commands Modules and GPIOs * Add Sonoff SC debug information * Change syslog service * Removed webserver syslog disable as now no longer needed * Increased default MQTT message size from 368 to 405 bytes while keeping MQTT_MAX_PACKET_SIZE = 512 (because we can) * Fix MQTT Offline or Remove MQTT retained topic code * Fix Domoticz loop when Emulation is selected * Add blink to WS2812 and Sonoff Led (#643) * Add option WIFI_WAIT (5) to command WifiConfig to allow connection retry to same AP without restart or update flash (#772, #869) * Add support for Witty Cloud (#794) * Add GPIO14 to Sonoff Dual (#797, #839) * Add support for Yunshan Wifi Relay (#802) * Add GPIO16 input pulldown (#827) * Add timeout to DHT and DS18B20 sensors (#852) * Fix watchdog timeout caused by lack of stack space by moving to heap (#853) * Allow LogPort and MqttPort up to 65535 and add LogPort tot Status 3 (#859) * Allow command SwitchTopic in group mode (#861) * Allow command SwitchMode if no switches are defined (#861) * Add optional dimmer parameter to command Wakeup for WS2812, AiLight, Sonoff B1, Led and BN-SZ01 (#867) * Fix basic On, Off, Toggle, Blink and BlinkOff commands when other language is selected (#874) * * 5.7.1 20170909 * Remove leading spaces from MQTT data * Fix webconsole special character entry * Allow # as prefix for color value * Fix Alexa detection and Hue App Update Request (#698, #854) * * 5.7.0 20170907 * Shrink module configuration webpage * Fix settings order during startup to allow for displaying debug messages * Fix some string length issues * Add more string length tests by using strncpy * Add Ai-Thinker RGBW led (AiLight) * Add Power check and add PulseTime to power check at startup (#526) * Add Supla Espablo support (#755) * Add more precision to Sonoff Pow period and power results using command WattRes 0|1 (#759) * Add basic internationalization and localization (#763) * Add more Sonoff Pow range checking (#772) * Fix invalid JSON (#786, #822) * Add duplicate check to received RF signal within 2 seconds for Sonoff Bridge (#810) * * 5.6.1 20170818 * Change module list order in webpage * Fix Sonoff T1 1CH and 2CH configuration (#751) * * 5.6.0 20170818 * Fix Sonoff Pow intermittent exception 0 * Change Sonoff Pow sending Domoticz telemetry data only * Add Ai-Thinker RGBW led (AiLight) (experimental) * Add NeoPixelBus library to Sonoff Led for Hue support * Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge * Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676) * Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color Temperature * Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1 * Add CT parameter to Hue * Add Sonoff T1 support (#582) * Add AnalogInput0 if configured as Analog Input to webpage (#697, #746) * Add command SetOption14 0|1 to enable interlock mode (#719, #721) * Fix Mitsubishi HVAC IR power controll (#740) * * 5.5.2 20170808 * Extent max number of WS2812 pixels from 256 to 512 (#667) * Add OTA handling if server responds with no update available (#695) * Removed undocumented command FlashMode (#696) * Fix compile time error message due to increased message buffer size (#703) * * 5.5.1 20170805 * Fix Sonoff Rf Bridge issues * Add Sonoff RF Bridge MQTT messages on received and learned RF signal * Add command VoltRes 0|1 to select voltage resolution to 0.1 V (#654) * Add averaging to Analog input (#686) * Add Energy tele data on Sonoff Pow Threshold change (#688) * Fix inconsistent property names in Messages (#690) * * 5.5.0 20170730 * Reduce code space by removing the following commands as they are replaced by SetOption alternatives: * SaveState = SetOption0 * ButtonRestrict = SetOption1 * Units = SetOption2 * MQTT = SetOption3 * MQTTResponse = SetOption4 * TempUnit = SetOption8 * Smoothing WS2812 animation poll, invert fade speed and max allowed wakeup time down to 3000 seconds * Fix initial button press detection * Add support for Sonoff RF Bridge 433 using command RfKey * Fix regression from 5.0.7 by increasing message buffer size from 360 to 368 to accomodate 4 x DS18x20 sensors (#637) * Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to send either ON/OFF or TOGGLE (#642) * Adjust HLW calibration limits to accomodate HuaFan device and add commands HlwPSet, HlwUSet and HlwISet (#654) * * 5.4.0 20170725 * Fix command reset regression introduced in 5.2.0 * Increase polling from 0.1 second to 0.05 second * Add multipress to all buttons * Fix button 1 double press behaviour on multi relay devices * Add support for Hua Fan Smart Socket (#479) * Add support for Sonoff 4ch Pro (#565) * Add command SetOption13 1 to allow immediate action on single button press * (disables multipress, hold and unrestricted commands) (#587) * * 5.3.0 20170715 * Major Hue rewrite which might introduce Alexa problems. If so, initiate an issue * Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control to Hue * Fix Sonoff Led Power, Dimmer and Color MQTT response (#176) * Add commands Delay and Backlog to allow multiple commands at once separated by ";" (#593) * Use default flashmode DOUT to solve restart hangs on esp8285 chips (#453, #598) * Change Web console column width from 99 to 300 (#599) * * 5.2.4 20170703 * Removed flash mode update after selecting different module solving esp8285 related problems * Add device type flag to sonoff_template.ino * Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led (#567) * * 5.2.3 20170630 * Change Sonoff Led color conversion code * Fix SetOption12 handling * Simplify auto configuration upgrade * Add option Upgrade to only upgrade to any higher version (Old PR #213) * Change FallbackTopic to cmnd// bypassing FullTopic and Prefix (#538) * * 5.2.2 20170625 * Add configuration SaveAddress to Status 1 and Information Page * Change Sonoff Led Color conversion from AtoH to strtol * Fix possible wrong uploads due to configuration overwrites (#542) * Fix payload negative numbers (#547) * * 5.2.1 20170622 * Fix Restore Configuration in case of lower version * Revert auto configuration upgrade allowing easy upgrade which was removed in version 5.2.0 * Fix config auto upgrade from versions below version 4.1.1 (#530) * * 5.2.0 20170619 * Add command SetOption12 1 to disable newly released configuration flash rotate to reduce flash wear * Fix command CounterDebounce by removing test for active GPIO (#524) * Add command SetOption33 1..250 to allow user configure POW Max_Power_Retry count (#525) * * 5.1.7 20170616 * Prep removal of SetOptions alternatives * Restore webpage upgrade error messages removed in 5.1.5 * Add hold button functionality to buttons 2 to 4 * Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds to 10 seconds (#200) * Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507) * Changed webpage form actions from post to get and use relative path url (#434, #522) * * 5.1.6 20170606 * Shrink code * Removed online configuration of Domoticz In and Domoticz Out MQTT strings * Removed commands DomoticzInTopic and DomoticzOutTopic * Add define KEY_HOLD_TIME to configure button hold threshold before sending MQTT Hold message * Add command StateText4 to configure button MQTT Hold text (= MQTT_CMND_HOLD) * Add command SetOption11 0|1 to swap pushbutton single and double press functionality (#200) * Add command SwitchMode 5 (PUSHBUTTONHOLD) and 6 (PUSHBUTTONHOLD_INV) (#489) * * 5.1.5 20170604 * Shrink code in preparation to ESP8266-Arduino 2.4.0-rc1 * Add effect parameter to HUE Device (#464) * * 5.1.4 20170601 * Removed pre-compiled versions from repository as they are available within the release * Changed HUE Device type to color supporting version (#464) * Fix compile error when BE_MINIMAL is selected (#467, #476) * Add multiple compiled versions to release using updated Travis script and platformio.ini (#467) * * 5.1.3 20170520 * Add Domoticz Counter * * 5.1.2 20170519 * Fix Counter/Timer JSON message and update Counter/Timer on webpage * Fix WS2812 Domoticz related regression issues * * 5.1.1 20170517 * Allow command FullTopic in group mode * Prepare for more use of RTC memory * Add independant WS2812 led string power control (#386, #390) * Add command Counter to control up to four GPIO falling edge interrupt counters or timers (#459) * Add command CounterType to select between pulse counting or pulse timing * Add command CounterDebounce to select global counter debounce time in mSec * * 5.1.0 20170513 * Fix Offline/Removal of retained topic when FullTopic is changed * Add FullTopic to MQTT Configuration and Information web pages * Add license model GPLv3 (#188) * * 5.0.7 20170511 * Fix possible exception 28 on empty command * Add command SetOption0 as replacement for SaveState * Add command SetOption1 as replacement for ButtonRestrict * Add command SetOption2 as replacement for Units * Add command SetOption4 as replacement for MqttResponse * Add command SetOption8 as replacement for TempUnit * Add command SetOption10 On|Off to select between Offline or Removing previous retained topic (#417, #436) * * 5.0.6 20170510 * Remove hyphen in case of a single DHT sensor connected (#427) * Add command MqttRetry to change default MQTT reconnect retry timer from minimal 10 seconds (#429) * * 5.0.5 20170508 * Add command FullTopic with tokens %topic% (replaced by command Topic value) and * %prefix% (replaced by command Prefix values) for more flexible topic definitions (#244) * See wiki > MQTT Features https://github.com/arendst/Sonoff-Tasmota/wiki/MQTT-Features for more information * * 5.0.4 20170505 * Add Sonoff Pow Energy Total up to 40 MWh * Add command EnergyReset 1|2|3 to reset Energy counters (#406) * Fix Domoticz Energy logging (#411) * Add command PowerOnState 4 to keep relay always on and disabling all power control (#418) * * 5.0.3 20170504 * Add command SensorRetain on|off to enable retaining of mqtt message tele/sonoff/SENSOR (#74) * Change WifiConfig timeout from 60 seconds to 180 seconds (#212) * Change Sonoff Touch command Ledstate functionality by turning led on if power is off (#214) * Add 4 seconds delay after power on before enabling button to workaround Wemos D1 mini RTS circuit (#380) * * 5.0.2 20170503 * Reset SaveData, SaveState and MqttResponse to default values due to rearranging settings * Moved some settings to flag area * Add command TempUnit Celsius|Fahrenheit for selecting Celsius or Fahrenheit (#347) * Add command TempRes 0..3 for selecting Temperature Resolution (#347) * Add command HumRes 0..3 for selecting Humidity Resolution (#347) * Add command PressRes 0..3 for selecting Pressure Resolution (#347) * Add command EnergyRes 0..5 for selecting Energy Resolution (#347) * Add "TempUnit":"C|F" to sensor JSON output (#347) * Add support for up to three DHT type sensors each using a different GPIO (#339, #404) * * 5.0.1 20170429 * Adjust Sonoff SC messages to prepare for display feature * Move static data from RAM to Flash * Fix PowerOnState for some devices not reporting "Power on" state (#284, #380, #383) * * 5.0.0 20170425 * Memory status message update * Fix setting migration to better preserve settings during move (#382) * Best practice is first doing a Backup Configuration before installing version 5.0.0 * Reset save count after setting move * Start using new linker script without SPIFFS * * 4.2.0 20170424 * Prepare for SPIFFS removal by moving settings to EEPROM area * Fix compilation error when webserver is disabled (#378) * * 4.1.3 20170410 * Add user configuarble GPIO to module S20 Socket and Slampher * Add support for Sonoff SC (#112) * Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led firmware (#122) * Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions due to power supply instabilities (#122) * Add Access Point Mac Address to Status 11 and Telemetry (#329) * Fix DS18B20 negative temperature readings (#334) * * 4.1.2 20170403 * Rename Unrecognised command to Unknown command * Remove all command lists * Remove command SmartConfig (superseded by WifiConfig) * Fix boot loop when selecting module Sonoff 4CH or Sonoff Touch on non ESP8285 hardware * Add optional support for Toshiba and Mitsubishi HVAC IR control (needs updated IRremote8266 library) (#83, #257) * Add all configured switches to Domoticz Configuration web page (#305) * Fix compile error when selecting WS2812 DMA (#313) * * 4.1.1 20170329 * Fix default Telemetry for command Prefix3 * Fix webserver Module parameters for disabled select * Fix sensor status for enabled switches * Remove Light as alternative for Power (save code space) * Remove migration option from pre V3 (code cleanup) * Remove unofficial SPIFFS support (code cleanup) * Remove command list when unknown command is entered (save code space) * Rename Status11 json from StatusPWR to unique StatusSTS * Rename command Gateway to IPAddres2, Subnetmask to IPAddress3 and DnsServer to IPAddress4 (save code space) * Add Command MqttResponse to select either command or RESULT topic as response (#258) * Add command StateText1 to StateText3 to assign MQTT_STATUS_OFF, MQTT_STATUS_ON and MQTT_CMND_TOGGLE respectively (#286) * Remove restart after IPAddress changes (#292) * Add support for MAX31850 in xsns_ds18x20.ino (#295) * Fix possible uptime update misses (#302) * * 4.1.0 20170325 * Change static IP addresses in user_config.h from list (using commas) to string (using dots) * Unify display result of commands Modules, Module and Gpios * Rewrite Module selection web page to bring size down from 18651 to 4319 bytes (!) (#234, #240) * Add basic support for (Lixada) H801 RGBWW controller (#252) * Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and PUB_PREFIX2 respectively (#255) * Add static ip addresses to flash (#262) * Add commands IpAddress, Gateway, Subnetmask and DnsServer to select static ip addresses (#273) * * 4.0.8 20170321 * Fix entering non-numeric webpassword * Force selection between TLS or Webserver due to memory restraint (#240) * Allow entering empty string using "0" for selected commands (#242) * Fix exception when posting commands to web console containing % (#250) * * 4.0.7 20170319 * Increased Sonoff Led PWM frequency from 432 to 1000 * Fix possible watch dog reboot after changing module type on web page * Fix reporting of GPIO usage from web page * Fix Sonoff Led blank during firmware upgrade * Fix Sonoff Led flicker and possible flash corruption by using latest Arduino-esp8266 versions * of pwm core files included in sonoff library (#211) * Add PWM output control with commands PWM1 to PWM5 using user selectable GPIOs (#211) * Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal (1000) and HlwICal (2500) (#223) * Add Switch state to sensor status (#227, #233) * Add user configuarble GPIO to module Sonoff Touch (#228) * Add define WEB_PORT to user_config.h to change default web server port from 80 (#232) * Fix failed Ota Firmware upgrade started from Web page (#235) * * 4.0.6 20170316 * Fix to better find device by Wifi hostname * Fix compile error when some I2C devices are disabled * Add (experimental) support for SHT1X emulating I2C (#97) * Add ADC to ElectroDragon (#203) * Add support for Sonoff Dev (#206) * * 4.0.5 20170314 * Add command Status 11 to show power status with Vcc if define USE_ADC_VCC is enabled (default) * Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with define USE_ADC_VCC disabled (#137) * Add MQTT host:port to timeout message (#199) * * 4.0.4 20170312 * Add pulse timers for up to 4 relays (#106) * Fix Sonoff Led power state when dimmer or color is 0 (#176) * Add command NtpServer to configure up to three NTP servers (#177) * Delete module User Test as module Wemos D1 mini has same/more user configurable GPIO (#178) * Add more user configurable GPIO to module ElectroDragon (#183) * * 4.0.3 20170309 * Renamed Module NodeMCU to WeMos D1 mini * Add GPIO1 as user option to some modules * Add Buttons, Relays and Leds to user configurable options (#159) * Add description on Module parameters web page to some well known GPIOs (#107, #171) * * 4.0.2 20170308 * Restore correct seriallog level after Serial logging was disabled * Add simple dimmer slider to Sonoff Led web page * Reduced root webpage size by 31% * Expand Status 2 with Build date/time and core version * Fix webserver redirection when not in WifiManager mode (#156) * Add command ButtonRestrict On/Off to restrict access to button hold and button multi press options above 2 (#161) * Fix DS18S20 negative temperature readings (#165) * Fix crlf compilation error due to bad syntax (#144, #167) * * 4.0.1 20170305 * Fix char default sizes and set MESSZ to 360 (#143) * Fix SerialLog setting status * Disable syslog when emulation is active * Add DS18B20 web page display refresh * * 4.0.0 20170303 * Add define to remove config migration code for versions below 3.0 (See Wiki-Upgrade-Migration path) * Free memory by switching from String to char[] * Raised Sonoff Led PWM frequency from 200Hz to 432Hz in search of stability (hardware watchdog timeouts) (#122) * Increase message size and suggested minimum MQTT_MAX_PACKET_SIZE to 512 (#114, #124) * Remove runtime warning message regarding MQTT_MAX_PACKET_SIZE too small as it is now moved to compile time (#124) * Fix possible panics with web console and http commands while UDP syslog is active (#127) * Add optional static IP address (#129) * Add define ENERGY_RESOLUTION in user_config.h to allow user control over precision (#136) * * 3.9.22 20170228 * Update web console * Fix Status 4 JSON message * Add Exception info during restart if available * Add osWatch service to detect loop hangs that might happen during (OTA) upgrades * Add WiOn support for relay and switch only (#82, #102) * Allow for user specified relay count up to four in sonoff_template.h (#109) * Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021 (#118) * Add NodeMCU or Wemos configuration option (#119) * * 3.9.21 20170224 * Add ajax to web root page and web console (#79) * Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84, #88) * Fix MQTT upgrade when webserver is active * * 3.9.20 20170221 * Add minimal basic authentication to Web Admin mode (#87) * Fix Hue and add HSB support (#89) * * 3.9.19 20170219 * Sonoff Led: Made GPIO04, 05 and 15 available for user * Sonoff Led: Add commands Fade, Speed, WakupDuration, Wakeup and LedTable * * 3.9.18 20170218 * Fix ledstate 0 to turn off led * Fix Sonoff Led dimmer range (#16) * Change Sonoff Led command Dimmer to act on both cold and warm color * Add Sonoff Led command Color CCWW where CCWW are hexadecimal values fro 00 - FF * Reduce Sonoff Led flickering by disabling interrupts during flash save and disabling * Led during OTA upgrade and Web upload (#16) * * 3.9.17 20170217 * Fix possible ArduinoJSON related memory fragmentation * Changed console logging using less memory * Add GPIO04 as user selectable for Sonoff Dual (#75) * * 3.9.16 20170214 * Update latching relay handler * Add support for IR led using IRremoteESP8266 library (#59) * Add Hue argument passing using ArduinoJSON library (#59) * * 3.9.15 20170213 * Change JSON float values from string to number according to http://json.org (#56) * Add support for exs latched relay module https://ex-store.de/ESP8266-WiFi-Relay-V31 (#58) * Add support for inverted relays * Changed MAX_LOG_LINES from 70 to 60 to preserve memory * * 3.9.14 20170211 * Add False and True as alternatives for 0/Off and 1/On (#49) * Fix Status10 JSON format (#52) * Fix DS18x20 using OneWire library (#53) * * 3.9.13 20170210 * Add FlashChipMode to Status 4 * Removed redundant DHT2 option and code * Add Sonoff SV GPIO pin 05 configuration (#40) * Add configuration file backup and restore via web page * Fix latency due to light_sleep mode even if sleep was set to zero (#50) * * 3.9.12 20170208 * Fix compile error when webserver is disabled (#30) * Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during OTA upload * Fix hostname issues by not allowing user entry of string formatting and removing from user_config.h (#36) * * 3.9.11 20170204 * Fix command I2Cscan * Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic * Make all TELEMETRY, STATUS and COMMAND message topics unique (#4) * Advertise command topic to be used by iobroker (#299) * Fix butten (non)detection if no GPIO_KEY1 is defined (#13) * Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars (#18) * Update web page with Build Date/Time, Emulation and mDNS Discovery and Advertise information (#21) * * 3.9.10 20170130 * Add WS2812 Color Type selection (RGB or GRB) to user_config.h (#7) * Hue api changes to support HUE App(s) (#8) * * 3.9.9 20170130 * Add command status 10 showing sensor data * Fix hlw status messages if hlw is disabled * * 3.9.8 20170130 * Remove GPIO07 and GPIO08 from user selectable (#5) * * 3.9.7 20170129 * Fix possible WS2812 exceptions when using emulation * Add command Emulation to dynamic configure Belkin WeMo and Hue Bridge for Alexa * * 3.9.6 20170129 * Add dynamic sleep for WS2812 animation (#1) * * 3.9.5 20170128 * Fix error message in case of wrong Domoticz command * * 3.9.4 20170127 * Fix Sonoff Dual Relay switching (#287) * * 3.9.3 20170127 * Add confirmation before Restart via webpage * Expand Domoticz Configuration webpage with Key, Switch and Sensor Index and * add commands DomoticzSwitchIdx and DomoticzSensorIdx (#86) (#174) (#219) * Fix default DHT11 sensor driver selection * Fix LedPower status after button press (#279) * Add command Sleep 0 - 250 mSec for optional light sleep mode to lower energy consumption (#272) * (Expect overall button/key/switch misses and wrong values on Sonoff Pow) * Add Hue brightness extension (#281) * Fix Hue brightness and change to call by reference (#283) * * 3.9.2 20170124 * Add confirmation before Reset Configuration via webpage (#244) * Add WS2812 features (see Wiki commands) * * 3.9.1 20170124 * Change PowerOnState function to only trigger when Power On (and not just restart) (#238) * Move HLW interrupts back to RAM and make WS2812_DMA optional as it generates Exception on Pow (#264) * Add charset=utf-8 to webpages (#266) * Update Hue emulation (#268) * Fix status module number * Add support for domoticz Dimmer on Sonoff_Led and WS2812 * Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during web upload * * 3.2.6a 20170120 * Fix Sonoff Pow compile error (#255) * Move HLW interrupts back to ROM (Needed for WS2812 DMA interrupts) * Removed all IO config from user_config.h as this will be done by commands or webpage * Removed MessageFormat and supports JSON only except POWER/LIGHT status * Add command LedPower to control main led (#247) * Add more FriendlyNames for Hue (#254) * Add DMA support for WS2812 when using pin 3 while other pins work just as well in my case... * Add HUE emulation for Alexa (#229) * Add basic WS2812 support (#229) * Fix Wemo when MQTT is disabled (#245) * Revert ButtonTopic and change SwitchTopic1 - 4 to one SwitchTopic * Rename MqttUnits to Units * Add Mqtt command to enable/disable MQTT * * 3.2.2a 20170115 * Add dynamic (Sonoff) Module, user GPIO and sensor selection (one size fits (almost) all) * Add support for Sonoff LED * Add Seriallog disable after 600 seconds for Sonoff Dual and 4 Channel * Add ButtonTopic2 - 4, SwitchTopic1 - 4 and SwitchRetain * * 3.2.2 20170113 * Fix PowerOnState 2 functionality after re-applying power (#230) * * 3.2.1 20170113 * Fix some failed command decoding (#228) * Removed passwords from status messages (#216) * * 3.2.0 20170111 * Add I2C BH1750 sensor (#222) * Sensor rewrite preparing for online selection * * 3.1.16 20170109 * Fix Domoticz possible error condition * Remove Wifi password from connection message (#216) * Add Configure Other menu item to web page (#209) * Add command FriendlyName, field Friendly Name and define FRIENDLY_NAME to be used by Alexa * eliminating current use of MQTT_CLIENT_ID (#209) * Add friendlyname to webpage replacing former hostname * * 3.1.15 20170108 * Fix Domoticz send key regression with Toggle command * * 3.1.14 20170107 * Add support for command TOGGLE (define MQTT_CMND_TOGGLE) when ButtonTopic is in use and not equal to Topic (#207) * * 3.1.13 20170107 * Fix web console command input when SUB_PREFIX contains '/' (#152) * Add command response to web command (#200) * Add option to disable MQTT as define USE_MQTT in user_config.h (#200) * * 3.1.12 20170106 * Add OTA retry to solve possible HTTP transient errors (#204) * Fix MQTT host discovery * * 3.1.11 20170105 * Add mDNS to advertise webserver as .local/ * * 3.1.10 20170105 * Fix ButtonTopic when SUB_PREFIX = PUB_PREFIX * Add workaround for possible MQTT queueing when SUB_PREFIX = PUB_PREFIX * Add optional MQTT host discovery using define USE_DISCOVERY in user_config.h (#115) * * 3.1.9 20170104 * Fix Power Blink start position (toggled) * Change PulseTime increments: 1 .. 111 in 0.1 sec (max 11 seconds) and 112 .. 64900 in seconds (= 12 seconds until 18 hours) (#188) * Add support for SUB_PREFIX = PUB_PREFIX (#190) * * 3.1.8 20170103 * Add retain flag to LWT offline and only send "tele/sonoff/LWT Offline" (#179) * Change retained LWT Online message to only send "tele/sonoff/LWT Online" * * 3.1.7 20161231 * Add retained message LWT Online when sonoff makes MQTT connection (#179) * * 3.1.6 20161230 * Add blinking using commands BlinkTime, BlinkCount and Power Blink|3|BlinkOff|4 (#165) * * 3.1.5 20161228 * Fix serial space command exception (28) * * 3.1.4 20161227 * Fix MQTT subscribe regression exception (3) (#162) * Fix serial empty command exception (28) * * 3.1.3 20161225 * Extent Domoticz configuration webpage with optional indices (#153) * Fix multi relay legacy tele message from tele/sonoff/2/POWER to tele/sonoff/POWER2 * Add support for iTead Motor Clockwise/Anticlockwise * * 3.1.2 20161224 * Extent command PowerOnState with toggle at power on (option 2 is now option 3!) (#156) * * 3.1.1 20161223 * Add support for Sonoff Touch and Sonoff 4CH (#40) * Update DomoticzIdx and DomoticzKeyIdx with relay/key index (DomoticzIdx1/DomoticzKeyIdx1) * Add command PowerOnState to control relay(s) at power on (#154) * * 3.1.0 20161221 * Add Sonoff Pow measurement smoothing * Fix serial command topic preamble error (#151) * Fix 2.x to 3.x migration inconsistencies (#146) * * 3.0.9 20161218 * Add Sonoff Pow voltage reading when relay is on but no load present (#123) * * 3.0.8 20161218 * Add temperature conversion to Fahrenheit as option in user_config.h (TEMP_CONVERSION) (#145) * * 3.0.7 20161217 * Add user_config_override.h to be used by user to override some defaults in user_config.h (#58) * Fix Sonoff Pow low power (down to 4W) intermittent measurements (#123) * * 3.0.6 20161217 * Fix MQTT_CLIENT_ID starting with % sign as in "%06X" (#142) * Add auto power off after PulseTime * 0.1 Sec to relay 1 (#134) * * 3.0.5 20161215 * Add more control over LED with command LedState options (#136, #143) * LED_OFF (0), LED_POWER (1), LED_MQTTSUB (2), LED_POWER_MQTTSUB (3), LED_MQTTPUB (4), LED_POWER_MQTTPUB (5), LED_MQTT (6), LED_POWER_MQTT (7) * Add option WIFI_RETRY (4) to command WifiConfig to allow connection retry to other AP without restart (#73) * * 3.0.4 20161211 * Fix intermittent Domoticz update misses (#133) * * 3.0.3 20161210 * Fix compiler warnings (#132) * Remove redundant code * Fix Domoticz pushbutton support * * 3.0.2 20161209 * Add pushbutton to SwitchMode (#130) * * 3.0.1 20161209 * Fix initial config * * 3.0.0 20161208 * Migrate and clean-up flash layout * Settings from version 2.x are saved but settings from version 3.x can not be used with version 2.x * Change SEND_TELEMETRY_RSSI to SEND_TELEMETRY_WIFI and add AP and SSID to telemetry * Split long JSON messages * Fix inconsistent status messages * Fix all status messages to return JSON if enabled * Remove relay index in cmnd/sonoff//POWER now changed * to cmnd/sonoff/POWER for single relay units * and cmnd/sonoff/POWER for multi relay units like Sonoff dual * Add retain option to Power/Light status controlled by command PowerRetain On|Off (#126) * * 2.1.2 20161204 * Add support for second wifi AP (#73) * Update command WifiConfig * Fix possible WifiManager hang * * 2.1.1a 20161203 * Fix scan for wifi networks if WeMo is enabled * Fix syslog setting using web page * * 2.1.1 20161202 * Add support for ElectroDragon second relay and button (only toggle with optional ButtonTopic) (#110) * * 2.1.0 20161202 * Add optional EXPERIMENTAL TLS to MQTT (#49) * Fix MQTT payload handling (#111) * Optimzed WeMo code * * 2.0.21a 20161201 * Fix WeMo PowerPlug emulation * * 2.0.21 20161130 * Add Belkin WeMo PowerPlug emulation enabled with USE_WEMO_EMULATION in user_config.h (Heiko Krupp) (#105, #109) * * 2.0.20 20161130 * Relax MQTTClient naming but only allows hexadecimal uppercase numbers (#107) * Add I2C support with command I2CScan * Add I2C sensor driver for HTU21 as alternate sensor using TH10/16 connectors (Heiko Krupp) (#105) * Add I2C sensor driver for BMP085/BMP180/BMP280/BME280 as alternate sensor using TH10/16 connectors * * 2.0.19a 20161127 * Add support for ButtonTopic and ButtonRetain to wall switch function * Add pullup to SWITCH_PIN and command SwitchMode to syntax * * 2.0.18 20161126 * Add SUB_PREFIX multi level support allowing 'cmnd' or 'cmnd/level2/level3' * Add wall switch function to GPIO14 and command SwitchMode (Alex Scott) (#103) * * 2.0.17 20161123 * Calibrate HLWPCAL from 12345 to 12530 * Add alternative sensor driver DHT2 using Adafruit DHT library * Add define MESSAGE_FORMAT to user_config.h * Throttle console messages * Shorten JSON messages * Fix possible Panic * Fix User mode webserver security * * 2.0.16 20161118 * Add alternative sensor driver DS18x20 using OneWire library (#95) * Change sensor MQTT message from tele/sonoff/TEMPERATURE to tele/sonoff/DHT/TEMPERATURE or * tele/sonoff/DS18B20/TEMPERATURE or tele/sonoff/DS18x20/1/TEMPERATURE * Add sensors to root webpage and auto refresh every 4 seconds (#92) * Add optional JSON messageformat to all telemetry data * Enforce minimum TelePeriod to be 10 seconds * Fix Energy Yesterday reset after restart * Add Energy Today restore after controlled restart * * 2.0.15 20161116 * Change TODAY_POWER and PERIOD_POWER to TODAY_ENERGY and PERIOD_ENERGY * Fix serial regression * Fix syslog hangs when loghost is unavailable * * 2.0.14 20161115 * Add HLW threshold delay * Fix HLW intermittent current deviation * Fix button functionality during wificonfig * Add CRC check to DS18B20 sensor (#88) * * 2.0.13 20161113 * Add additional upload error code descriptions * Add PlatformIO support (#80) * * 2.0.12 20161113 * Fix Serial and Web response regression when no MQTT connection available * Fix Sonoff Dual power telemetric data for second relay * Removed MQTT password from Information web page * Hide MQTT password from Configure MQTT web page * * 2.0.11 20161111 * Rewrite button and web toggle code * Fix NTP sync * Add HLW calibration commands HLWPCAL, HLWUCAL and HLWICAL (need define USE_POWERCALIBRATION) * Fix power threshold tests * * 2.0.10 20161109 * Add additional Domoticz define (#63) * Add defines MQTT_STATUS_ON and MQTT_STATUS_OFF in user_config.h to select status On/Off string * Fix status response differences (#65) * Fix divide by zero exception (#70) * Fix syslog loop exception * * 2.0.9 20161108 * clarify MODULE in user_config.h * Fix hlw false values * * 2.0.8 20161108 * Add initial status after power on * Seperate driver files * Fix hlw code and calibrate Pow * Move user config defines to user_config.h (#61) * * 2.0.7 20161030 * Make Ticker mandatory * Add Domoticz support (Increase MQTT_MAX_PACKET_SIZE to 400) (#54) * Add command MessageFormat 0|1 to select either legacy or JSON output * * 2.0.6 20161024 * Add Sonoff Pow power factor * Initial support for up to four relays using iTEAD PSB (4Channel) * - Currently only supports one button (All buttons behave the same) * - Use command MODEL 4 to select four relay option * (After first power on it will support 2 relays like Sonoff Dual) * Fix ledstate * Add command Status 9 to display Sonoff Pow thresholds * Add commands PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow and CurrentHigh for use * with Sonoff Pow thresholds * * 2.0.5 20161018 * Add updates to user_config.h - moved SEND_TELEMETRY_DS18B20 and SEND_TELEMETRY_DHT to module area. * As Sonoff TH10/16 does not have the logic installed for GPIO04 You'll have to select ONE of both * Add Sonoff Pow support (experimental until Pow tested) * Add command Status 8 to display Sonoff Pow energy values * Add command MqttUnits On|Off to add units to values * Change web main page header character size * Change On/Off to ON/OFF status messages to satisfy openHAB * Change TEMP to TEMPERATURE and HUM to HUMIDITY * * 2.0.4 20161009 * Add MQTT_BUTTON_RETAIN, SAVE_DATA and SAVE_STATE defines to user_config.h (#35) * Update ButtonRetain to remove retained message(s) from broker when turned off * Add Retain for second relay on Sonoff Dual * Provide power status messages with device topic index if requested * * 2.0.3 20161008 * Update wifi initialization * Add command BUTTONRETAIN for optional MQTT retain on button press (#35) * Add command SAVESTATE to disable power state save. May be used with MQTT retain * * 2.0.2 20161006 * Fix wifi issue 2186 * * 2.0.1 20161002 * Fix button press * * 2.0.0 20161002 * Update Sonoff TH10/16 sensor pins (My TH10 only has GPIO14 connected) * Add full support for Sonoff dual * * 1.0.35 20160929 * Add more lines to console * Add timeout and disable MQTT on web upload * Add command SAVEDATA to control parameter save (for flash wear afficionados) (#30) * * 1.0.34 20160926 * Fix button press six and seven * Add more information to webserver * * 1.0.33 20160915 * Better WPS error message * Separate webserver code from support.ino into webserver.ino * Fix webserver User by removing unwanted restart option * * 1.0.32 20160913 * Add Wifi Protected Setup (WPS) as third option for initial config * Add command WIFICONFIG replacing deprecated command SMARTCONFIG * Add option WIFICONFIG 3 to start WPSconfig * Add option WIFICONFIG 0 to start saved Wifi config tool (WPSconfig, Smartconfig or Wifimanager) * Change button behaviour - See Wiki * * 1.0.31 20160907 * Fix DS18B20 misread if teleperiod = 2 * Tuned sensor code * Updated prefered ElectroDragon connection to Relay 1 and Button 1 * Moved SONOFF and ELECTRO_DRAGON port config to user_config.h * * 1.0.30 20160902 * Fix command TELEPERIOD 0 * Add ESP- tag to UDP log message for easy rsyslogd filtering * Add ElectroDragon (Relay 2 only) functionality. Select with #define MODULE ELECTRO_DRAGON * Add ? as null message alternative * Add DHT temperature and humidity telemetry support. Enable with #define SEND_TELEMETRY_DHT * Add DS18B20 temperature telemetry support. Enable with #define SEND_TELEMETRY_DS18B20 * Restrict HOSTNAME, MQTTCLIENT, TOPIC and BUTTONTOPIC in topic mode only * * 1.0.29 20160831 * Allow UPGRADE, OTAURL, RESTART, RESET, MQTTHOST, MQTTPORT, MQTTUSER, MQTTPASSWORD and WEBSERVER also in group mode * * 1.0.28 20160831 * Add webserver state to status 5 * Add optional PUB_PREFIX2 (tele) for telemetry usage * Add command TELEPERIOD * Fix syntax message * Change memory status display * * 1.0.27 20160831 * Add sketch flash size * Add console to webserver * Add command weblog * Change WifiManager web pages to minimal * Change display default hostname and MQTT client id in webserver * Change HTTP command interface to http://sonoff-1234/cm?cmnd=light 2 * Change HEARTBEAT to UPTIME * * 1.0.26 20160829 * Add define USE_WEBSERVER to disable web server code in source * Add file upload as alternative for ota upload to webserver * Add information to webserver * Add command hostname * Add command logport * Change HTTP command interface to http://sonoff-1234/cmd?cmnd=light 2 * Change button behaviour with regards to Smartconfig and OTA upload. See README.md * Enforce default hostname to either "%s-%04d" or user defined without any % * Enforce default mqtt client id to either "DVES_%06X" or user defined without any % * * 1.0.25 20160822 * Remove config system halts to keep ota available * * 1.0.24 20160821 * Add test for MQTT_SUBTOPIC * Change log range to LOG_LEVEL_ALL * Change MQTT introduction messages * Moved MQTT_MAX_PACKET_SIZE warning message to introduction messages * * 1.0.23 20160821 * Add option USE_SPIFFS to move config from flash to spiffs * Add webserver with options 0 (off), 1 (user) and 2 (admin) * Add HTTP command interface (http://sonoff-1234/c?cmnd=light 2) * Add wifimanager countdown counter * Add command line webpage * Add relay control to wifimanager * Add restart option 99 to force restart * Fix wifi hostname * Fix NETBIOS hostname problem by reducing default hostname length * Fix possible exception if WIFI_HOSTNAME is changed * Fix upgrade messages * Reduce memory use by redesigning config routines * Split syntax message * Rename define SERIAL_IO to USE_SERIAL * * 1.0.22 20160814 * Add all MQTT parameters for configuration * Add wifimanager to configure Wifi and MQTT via web server * Change NTP time handling * Fix Smartconfig parameter buffer overflow * Fix PlatformIO warnings * * 1.0.21 20160808 * Remove semaphore as subscription flooding (more than 15 subscriptions per second) is managed by SDK (LmacRxBlk:1) * Add optional RTC interrupt (define USE_TICKER) to keep RTC synced during subscription flooding * Remove heartbeatflag * * 1.0.20 20160805 * Add semaphore to handle out of memory when too many subscriptions requested * Use Daylight Saving (DST) parameters from user_config.h when timezone = 99 * Add status 7 option displaying RTC information * Add ledstate to status 0 * * 1.0.19 20160803 * Fix possible MQTT_CLIENT_ID induced Exception(28) * * 1.0.18 20160803 * Moved Cfg_Default * Fix negative data handling * Remove MQTT information from status 1 and add labels to status 1 * Add mac address to status 5 * Add MQTT ClientId, UserId and Password to status 6 * * 1.0.17 20160731 * Better variable range checking * Change ambiguous connection messages * Add timestamp to serial message * * 1.0.16 20160729 * Moved wifi, rtc, syslog and config to support.ino * Fixed button action when buttontopic is used. Introduced with 1.0.15 * Better buffer overflow checks (strlcpy) * * 1.0.15 20160728 * Removed pubsubclient config changes from sonoff.ino as it doesn't work * reapply MQTT_MAX_PACKET_SIZE 256 and MQTT_KEEPALIVE 120 to PubSubClient.h * Add status 0 option displaying all status messages * Change MQTT_MAX_PACKET_SIZE from 1024 to 256 * Add buffer overflow checks (snprintf and strncpy) * Implemented common string sizes * * 1.0.14 20160722 * Seperate user config from sonoff.ino to user_config.h (pucebaboon) * Change defaults from sidnas2 to domus1 * Add MQTT status message as status 6 (pucebaboon) * Add status type to message (pucebaboon) * Add pubsubclient config changes to sonoff.ino (pucebaboon) * * 1.0.13 20160702 * Add Ledstate 1 option to show power state on led * * 1.0.12 20160529 * Allow disable of button topic using "0" * * 1.0.11 20160524 * Provide button response if MQTT connection lost * * 1.0.10 20160520 * Add optional button topic to assist external MQTT clients * Change version notation * Reset default values * * 1.0.9 20160503 * Add more blinks * Add reset 2 option erasing flash * Add status 5 option displaying network info * Add syslog check for Wifi connection * Resize MqttPublish log array * Change Wifi smartconfig active from 100 to 60 seconds * Update Wifi initialization * * 1.0.8 20160430 * Remove use of Wifi config data from SDK * Add status 3 (syslog info) and status 4 (flash info) * Add restart option to button (5 quick presses) * * 1.0.7 20160420 * Add UDP syslog support * Change HOST command to MQTTHOST command * Add commands SYSLOG, SERIALLOG and LOGHOST * Change hostname to lower case to distinguise between open-sdk version * Add support for ESP-12F used in my modified wkaku power socket switch * Fix timezone command * Add RTC month names for future use * Modify button code * Remove initialization errors by better use of MQTT loop * * 1.0.6 20160406 * Removed Wifi AP mode (#1) * Add test for Arduino IDE version >= 1.6.8 * Fix RTC time sync code * * 1.0.5 20160310 * Initial public release * Show debug info by selecting option from IDE Tools Debug port: Serial \*********************************************************************************************/