/*
xsns_02_analog.ino - ADC support for Tasmota
Copyright (C) 2021 Theo Arends
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see .
*/
#ifdef USE_ADC
/*********************************************************************************************\
* ADC support for ESP8266 GPIO17 (=PIN_A0) and ESP32 up to 8 channels on GPIO32 to GPIO39
\*********************************************************************************************/
#define XSNS_02 2
#ifdef ESP8266
#define ANALOG_RESOLUTION 10 // 12 = 4095, 11 = 2047, 10 = 1023
#define ANALOG_RANGE 1023 // 4095 = 12, 2047 = 11, 1023 = 10
#define ANALOG_PERCENT 10 // backward compatible div10 range
#endif // ESP8266
#ifdef ESP32
#undef ANALOG_RESOLUTION
#define ANALOG_RESOLUTION 12 // 12 = 4095, 11 = 2047, 10 = 1023
#undef ANALOG_RANGE
#define ANALOG_RANGE 4095 // 4095 = 12, 2047 = 11, 1023 = 10
#undef ANALOG_PERCENT
#define ANALOG_PERCENT ((ANALOG_RANGE + 50) / 100) // approximation to 1% ADC range
#endif // ESP32
#define TO_CELSIUS(x) ((x) - 273.15)
#define TO_KELVIN(x) ((x) + 273.15)
// Parameters for equation
#define ANALOG_V33 3.3 // ESP8266 Analog voltage
#define ANALOG_T0 TO_KELVIN(25.0) // 25 degrees Celcius in Kelvin (= 298.15)
// Shelly 2.5 NTC Thermistor
// 3V3 --- ANALOG_NTC_BRIDGE_RESISTANCE ---v--- NTC --- Gnd
// |
// ADC0
#define ANALOG_NTC_BRIDGE_RESISTANCE 32000 // NTC Voltage bridge resistor
#define ANALOG_NTC_RESISTANCE 10000 // NTC Resistance
#define ANALOG_NTC_B_COEFFICIENT 3350 // NTC Beta Coefficient
// LDR parameters
// 3V3 --- LDR ---v--- ANALOG_LDR_BRIDGE_RESISTANCE --- Gnd
// |
// ADC0
#define ANALOG_LDR_BRIDGE_RESISTANCE 10000 // LDR Voltage bridge resistor
#define ANALOG_LDR_LUX_CALC_SCALAR 12518931 // Experimental
#define ANALOG_LDR_LUX_CALC_EXPONENT -1.4050 // Experimental
// CT Based Apparrent Power Measurement Parameters
// 3V3 --- R1 ----v--- R1 --- Gnd
// |
// CT+ CT-
// |
// ADC0
// Default settings for a 20A/1V Current Transformer.
// Analog peak to peak range is measured and converted to RMS current using ANALOG_CT_MULTIPLIER
#define ANALOG_CT_FLAGS 0 // (uint32_t) reserved for possible future use
#define ANALOG_CT_MULTIPLIER 2146 // (uint32_t) Multiplier*100000 to convert raw ADC peak to peak range 0..ANALOG_RANGE to RMS current in Amps. Value of 100000 corresponds to 1
#define ANALOG_CT_VOLTAGE 2300 // (int) Convert current in Amps to apparrent power in Watts using voltage in Volts*10. Value of 2200 corresponds to 220V
#define CT_FLAG_ENERGY_RESET (1 << 0) // Reset energy total
// Buttons
// ---- Inverted
// 3V3 ---| |----|
// |
// 3V3 --- R1 ----|--- R1 --- Gnd
// |
// |---| |--- Gnd
// | ----
// ADC
#define ANALOG_BUTTON 128 // Add resistor tolerance
// Odroid joysticks
// ---- Up
// 3V3 ---| |------------
// |
// ---- Dn |--- R10k --- Gnd
// 3V3 ---| |--- R10k ---|
// |
// ADC
// Press "Up" will raise ADC to ANALOG_RANGE, Press "Dn" will raise ADC to ANALOG_RANGE/2
#define ANALOG_JOYSTICK (ANALOG_RANGE / 3) +100 // Add resistor tolerance
// pH scale minimum and maximum values
#define ANALOG_PH_MAX 14.0
#define ANALOG_PH_MIN 0.0
// Default values for calibration solution with lower PH
#define ANALOG_PH_CALSOLUTION_LOW_PH 4.0
#define ANALOG_PH_CALSOLUTION_LOW_ANALOG_VALUE 282
// Default values for calibration solution with higher PH
#define ANALOG_PH_CALSOLUTION_HIGH_PH 9.18
#define ANALOG_PH_CALSOLUTION_HIGH_ANALOG_VALUE 435
// Multiplier used to store pH with 2 decimal places in a non decimal datatype
#define ANALOG_PH_DECIMAL_MULTIPLIER 100.0
struct {
uint8_t present = 0;
uint8_t type = 0;
} Adcs;
struct {
float temperature = 0;
float current = 0;
float energy = 0;
uint32_t param1 = 0;
uint32_t param2 = 0;
int param3 = 0;
int param4 = 0;
uint32_t previous_millis = 0;
uint16_t last_value = 0;
uint8_t type = 0;
uint8_t pin = 0;
} Adc[MAX_ADCS];
#ifdef ESP8266
bool adcAttachPin(uint8_t pin) {
return (ADC0_PIN == pin);
}
#endif
void AdcSaveSettings(uint32_t idx) {
char parameters[32];
snprintf_P(parameters, sizeof(parameters), PSTR("%d,%d,%d,%d,%d"),
Adc[idx].type, Adc[idx].param1, Adc[idx].param2, Adc[idx].param3, Adc[idx].param4);
SettingsUpdateText(SET_ADC_PARAM1 + idx, parameters);
}
void AdcGetSettings(uint32_t idx) {
char parameters[32];
Adcs.type = 0;
Adc[idx].param1 = 0;
Adc[idx].param2 = 0;
Adc[idx].param3 = 0;
Adc[idx].param4 = 0;
if (strchr(SettingsText(SET_ADC_PARAM1 + idx), ',') != nullptr) {
Adcs.type = atoi(subStr(parameters, SettingsText(SET_ADC_PARAM1 + idx), ",", 1));
Adc[idx].param1 = atoi(subStr(parameters, SettingsText(SET_ADC_PARAM1 + idx), ",", 2));
Adc[idx].param2 = atoi(subStr(parameters, SettingsText(SET_ADC_PARAM1 + idx), ",", 3));
Adc[idx].param3 = atoi(subStr(parameters, SettingsText(SET_ADC_PARAM1 + idx), ",", 4));
Adc[idx].param4 = atoi(subStr(parameters, SettingsText(SET_ADC_PARAM1 + idx), ",", 5));
}
}
void AdcInitParams(uint8_t idx) {
if ((Adcs.type != Adc[idx].type) || (Adc[idx].param1 > 1000000)) {
if (ADC_TEMP == Adc[idx].type) {
// Default Shelly 2.5 and 1PM parameters
Adc[idx].param1 = ANALOG_NTC_BRIDGE_RESISTANCE;
Adc[idx].param2 = ANALOG_NTC_RESISTANCE;
Adc[idx].param3 = ANALOG_NTC_B_COEFFICIENT * 10000;
}
else if (ADC_LIGHT == Adc[idx].type) {
Adc[idx].param1 = ANALOG_LDR_BRIDGE_RESISTANCE;
Adc[idx].param2 = ANALOG_LDR_LUX_CALC_SCALAR;
Adc[idx].param3 = ANALOG_LDR_LUX_CALC_EXPONENT * 10000;
}
else if (ADC_RANGE == Adc[idx].type) {
Adc[idx].param1 = 0;
Adc[idx].param2 = ANALOG_RANGE;
Adc[idx].param3 = 0;
Adc[idx].param4 = 100;
}
else if (ADC_CT_POWER == Adc[idx].type) {
Adc[idx].param1 = ANALOG_CT_FLAGS; // (uint32_t) 0
Adc[idx].param2 = ANALOG_CT_MULTIPLIER; // (uint32_t) 100000
Adc[idx].param3 = ANALOG_CT_VOLTAGE; // (int) 10
}
else if (ADC_PH == Adc[idx].type) {
Adc[idx].param1 = ANALOG_PH_CALSOLUTION_LOW_PH * ANALOG_PH_DECIMAL_MULTIPLIER; // PH of the calibration solution 1, which is the one with the lower PH
Adc[idx].param2 = ANALOG_PH_CALSOLUTION_LOW_ANALOG_VALUE; // Reading of AnalogInput while probe is in solution 1
Adc[idx].param3 = ANALOG_PH_CALSOLUTION_HIGH_PH * ANALOG_PH_DECIMAL_MULTIPLIER; // PH of the calibration solution 2, which is the one with the higher PH
Adc[idx].param4 = ANALOG_PH_CALSOLUTION_HIGH_ANALOG_VALUE; // Reading of AnalogInput while probe is in solution 2
}
}
if ((Adcs.type != Adc[idx].type) || (0 == Adc[idx].param1) || (Adc[idx].param1 > ANALOG_RANGE)) {
if ((ADC_BUTTON == Adc[idx].type) || (ADC_BUTTON_INV == Adc[idx].type)) {
Adc[idx].param1 = ANALOG_BUTTON;
}
else if (ADC_JOY == Adc[idx].type) {
Adc[idx].param1 = ANALOG_JOYSTICK;
}
}
}
void AdcAttach(uint8_t pin, uint8_t type) {
if (Adcs.present == MAX_ADCS) { return; }
Adc[Adcs.present].pin = pin;
if (adcAttachPin(Adc[Adcs.present].pin)) {
Adc[Adcs.present].type = type;
// analogSetPinAttenuation(Adc[Adcs.present].pin, ADC_11db); // Default
Adcs.present++;
}
}
void AdcInit(void) {
Adcs.present = 0;
for (uint32_t i = 0; i < MAX_ADCS; i++) {
if (PinUsed(GPIO_ADC_INPUT, i)) {
AdcAttach(Pin(GPIO_ADC_INPUT, i), ADC_INPUT);
}
if (PinUsed(GPIO_ADC_TEMP, i)) {
AdcAttach(Pin(GPIO_ADC_TEMP, i), ADC_TEMP);
}
if (PinUsed(GPIO_ADC_LIGHT, i)) {
AdcAttach(Pin(GPIO_ADC_LIGHT, i), ADC_LIGHT);
}
if (PinUsed(GPIO_ADC_RANGE, i)) {
AdcAttach(Pin(GPIO_ADC_RANGE, i), ADC_RANGE);
}
if (PinUsed(GPIO_ADC_CT_POWER, i)) {
AdcAttach(Pin(GPIO_ADC_CT_POWER, i), ADC_CT_POWER);
}
if (PinUsed(GPIO_ADC_JOY, i)) {
AdcAttach(Pin(GPIO_ADC_JOY, i), ADC_JOY);
}
if (PinUsed(GPIO_ADC_PH, i)) {
AdcAttach(Pin(GPIO_ADC_PH, i), ADC_PH);
}
}
for (uint32_t i = 0; i < MAX_KEYS; i++) {
if (PinUsed(GPIO_ADC_BUTTON, i)) {
AdcAttach(Pin(GPIO_ADC_BUTTON, i), ADC_BUTTON);
}
else if (PinUsed(GPIO_ADC_BUTTON_INV, i)) {
AdcAttach(Pin(GPIO_ADC_BUTTON_INV, i), ADC_BUTTON_INV);
}
}
if (Adcs.present) {
#ifdef ESP32
analogSetClockDiv(1); // Default 1
#if CONFIG_IDF_TARGET_ESP32
analogSetWidth(ANALOG_RESOLUTION); // Default 12 bits (0 - 4095)
#endif // CONFIG_IDF_TARGET_ESP32
analogSetAttenuation(ADC_11db); // Default 11db
#endif
for (uint32_t idx = 0; idx < Adcs.present; idx++) {
AdcGetSettings(idx);
AdcInitParams(idx);
AdcSaveSettings(idx);
}
}
}
uint16_t AdcRead(uint32_t pin, uint32_t factor) {
// factor 1 = 2 samples
// factor 2 = 4 samples
// factor 3 = 8 samples
// factor 4 = 16 samples
// factor 5 = 32 samples
uint32_t samples = 1 << factor;
uint32_t analog = 0;
for (uint32_t i = 0; i < samples; i++) {
analog += analogRead(pin);
delay(1);
}
analog >>= factor;
return analog;
}
#ifdef USE_RULES
void AdcEvery250ms(void) {
char adc_idx[3] = { 0 };
uint32_t offset = 0;
for (uint32_t idx = 0; idx < Adcs.present; idx++) {
#ifdef ESP32
snprintf_P(adc_idx, sizeof(adc_idx), PSTR("%d"), idx +1);
offset = 1;
#endif
if (ADC_INPUT == Adc[idx].type) {
uint16_t new_value = AdcRead(Adc[idx].pin, 5);
if ((new_value < Adc[idx].last_value -ANALOG_PERCENT) || (new_value > Adc[idx].last_value +ANALOG_PERCENT)) {
Adc[idx].last_value = new_value;
uint16_t value = Adc[idx].last_value / ANALOG_PERCENT;
Response_P(PSTR("{\"ANALOG\":{\"A%ddiv10\":%d}}"), idx + offset, (value > 99) ? 100 : value);
XdrvRulesProcess();
}
}
else if (ADC_JOY == Adc[idx].type) {
uint16_t new_value = AdcRead(Adc[idx].pin, 1);
if (new_value && (new_value != Adc[idx].last_value)) {
Adc[idx].last_value = new_value;
uint16_t value = new_value / Adc[idx].param1;
Response_P(PSTR("{\"ANALOG\":{\"Joy%s\":%d}}"), adc_idx, value);
XdrvRulesProcess();
} else {
Adc[idx].last_value = 0;
}
}
}
}
#endif // USE_RULES
uint8_t AdcGetButton(uint32_t pin) {
for (uint32_t idx = 0; idx < Adcs.present; idx++) {
if (Adc[idx].pin == pin) {
if (ADC_BUTTON_INV == Adc[idx].type) {
return (AdcRead(Adc[idx].pin, 1) < Adc[idx].param1);
}
else if (ADC_BUTTON == Adc[idx].type) {
return (AdcRead(Adc[idx].pin, 1) > Adc[idx].param1);
}
}
}
return 0;
}
uint16_t AdcGetLux(uint32_t idx) {
int adc = AdcRead(Adc[idx].pin, 2);
// Source: https://www.allaboutcircuits.com/projects/design-a-luxmeter-using-a-light-dependent-resistor/
double resistorVoltage = ((double)adc / ANALOG_RANGE) * ANALOG_V33;
double ldrVoltage = ANALOG_V33 - resistorVoltage;
double ldrResistance = ldrVoltage / resistorVoltage * (double)Adc[idx].param1;
double ldrLux = (double)Adc[idx].param2 * FastPrecisePow(ldrResistance, (double)Adc[idx].param3 / 10000);
return (uint16_t)ldrLux;
}
float AdcGetPh(uint32_t idx) {
int adc = AdcRead(Adc[idx].pin, 2);
float y1 = Adc[idx].param1 / ANALOG_PH_DECIMAL_MULTIPLIER;
uint32_t x1 = Adc[idx].param2;
float y2 = Adc[idx].param3 / ANALOG_PH_DECIMAL_MULTIPLIER;
uint32_t x2 = Adc[idx].param4;
float m = (y2 - y1) / (x2 - x1);
float ph = m * (adc - x1) + y1;
char phLow_chr[6];
char phHigh_chr[6];
dtostrfd(y1, 2, phLow_chr);
dtostrfd(y2, 2, phHigh_chr);
AddLog(LOG_LEVEL_DEBUG, PSTR(D_LOG_APPLICATION "Analog pH read. ADC-RAW: %d, cal-low(pH=ADC): %s=%d, cal-high(pH=ADC): %s=%d"), adc, phLow_chr, x1, phHigh_chr,x2);
return ph;
}
uint16_t AdcGetRange(uint32_t idx) {
// formula for calibration: value, fromLow, fromHigh, toLow, toHigh
// Example: 514, 632, 236, 0, 100
// int( (( - ) / ( - ) ) * ( - ) ) + )
int adc = AdcRead(Adc[idx].pin, 2);
double adcrange = ( ((double)Adc[idx].param2 - (double)adc) / ( ((double)Adc[idx].param2 - (double)Adc[idx].param1)) * ((double)Adc[idx].param3 - (double)Adc[idx].param4) + (double)Adc[idx].param4 );
return (uint16_t)adcrange;
}
void AdcGetCurrentPower(uint8_t idx, uint8_t factor) {
// factor 1 = 2 samples
// factor 2 = 4 samples
// factor 3 = 8 samples
// factor 4 = 16 samples
// factor 5 = 32 samples
uint8_t samples = 1 << factor;
uint16_t analog = 0;
uint16_t analog_min = ANALOG_RANGE;
uint16_t analog_max = 0;
if (0 == Adc[idx].param1) {
for (uint32_t i = 0; i < samples; i++) {
analog = analogRead(Adc[idx].pin);
if (analog < analog_min) {
analog_min = analog;
}
if (analog > analog_max) {
analog_max = analog;
}
delay(1);
}
Adc[idx].current = (float)(analog_max-analog_min) * ((float)(Adc[idx].param2) / 100000);
}
else {
analog = AdcRead(Adc[idx].pin, 5);
if (analog > Adc[idx].param1) {
Adc[idx].current = ((float)(analog) - (float)Adc[idx].param1) * ((float)(Adc[idx].param2) / 100000);
}
else {
Adc[idx].current = 0;
}
}
float power = Adc[idx].current * (float)(Adc[idx].param3) / 10;
uint32_t current_millis = millis();
Adc[idx].energy = Adc[idx].energy + ((power * (current_millis - Adc[idx].previous_millis)) / 3600000000);
Adc[idx].previous_millis = current_millis;
}
void AdcEverySecond(void) {
for (uint32_t idx = 0; idx < Adcs.present; idx++) {
if (ADC_TEMP == Adc[idx].type) {
int adc = AdcRead(Adc[idx].pin, 2);
// Steinhart-Hart equation for thermistor as temperature sensor
double Rt = (adc * Adc[idx].param1) / (1024.0 * ANALOG_V33 - (double)adc);
double BC = (double)Adc[idx].param3 / 10000;
double T = BC / (BC / ANALOG_T0 + TaylorLog(Rt / (double)Adc[idx].param2));
Adc[idx].temperature = ConvertTemp(TO_CELSIUS(T));
}
else if (ADC_CT_POWER == Adc[idx].type) {
AdcGetCurrentPower(idx, 5);
}
}
}
void AdcShowContinuation(bool *jsonflg) {
if (*jsonflg) {
ResponseAppend_P(PSTR(","));
} else {
ResponseAppend_P(PSTR(",\"ANALOG\":{"));
*jsonflg = true;
}
}
void AdcShow(bool json) {
bool domo_flag[ADC_END] = { false };
char adc_name[10] = { 0 }; // ANALOG8
char adc_idx[3] = { 0 };
uint32_t offset = 0;
bool jsonflg = false;
for (uint32_t idx = 0; idx < Adcs.present; idx++) {
#ifdef ESP32
snprintf_P(adc_name, sizeof(adc_name), PSTR("Analog%d"), idx +1);
snprintf_P(adc_idx, sizeof(adc_idx), PSTR("%d"), idx +1);
offset = 1;
#endif
switch (Adc[idx].type) {
case ADC_INPUT: {
uint16_t analog = AdcRead(Adc[idx].pin, 5);
if (json) {
AdcShowContinuation(&jsonflg);
ResponseAppend_P(PSTR("\"A%d\":%d"), idx + offset, analog);
#ifdef USE_WEBSERVER
} else {
WSContentSend_PD(HTTP_SNS_ANALOG, "", idx + offset, analog);
#endif // USE_WEBSERVER
}
break;
}
case ADC_TEMP: {
if (json) {
AdcShowContinuation(&jsonflg);
ResponseAppend_P(PSTR("\"" D_JSON_TEMPERATURE "%s\":%*_f"), adc_idx, Settings.flag2.temperature_resolution, &Adc[idx].temperature);
if ((0 == TasmotaGlobal.tele_period) && (!domo_flag[ADC_TEMP])) {
#ifdef USE_DOMOTICZ
DomoticzFloatSensor(DZ_TEMP, Adc[idx].temperature);
domo_flag[ADC_TEMP] = true;
#endif // USE_DOMOTICZ
#ifdef USE_KNX
KnxSensor(KNX_TEMPERATURE, Adc[idx].temperature);
#endif // USE_KNX
}
#ifdef USE_WEBSERVER
} else {
WSContentSend_Temp(adc_name, Adc[idx].temperature);
#endif // USE_WEBSERVER
}
break;
}
case ADC_LIGHT: {
uint16_t adc_light = AdcGetLux(idx);
if (json) {
AdcShowContinuation(&jsonflg);
ResponseAppend_P(PSTR("\"" D_JSON_ILLUMINANCE "%s\":%d"), adc_idx, adc_light);
#ifdef USE_DOMOTICZ
if ((0 == TasmotaGlobal.tele_period) && (!domo_flag[ADC_LIGHT])) {
DomoticzSensor(DZ_ILLUMINANCE, adc_light);
domo_flag[ADC_LIGHT] = true;
}
#endif // USE_DOMOTICZ
#ifdef USE_WEBSERVER
} else {
WSContentSend_PD(HTTP_SNS_ILLUMINANCE, adc_name, adc_light);
#endif // USE_WEBSERVER
}
break;
}
case ADC_RANGE: {
uint16_t adc_range = AdcGetRange(idx);
if (json) {
AdcShowContinuation(&jsonflg);
ResponseAppend_P(PSTR("\"" D_JSON_RANGE "%s\":%d"), adc_idx, adc_range);
#ifdef USE_WEBSERVER
} else {
WSContentSend_PD(HTTP_SNS_RANGE, adc_name, adc_range);
#endif // USE_WEBSERVER
}
break;
}
case ADC_CT_POWER: {
AdcGetCurrentPower(idx, 5);
float voltage = (float)(Adc[idx].param3) / 10;
char voltage_chr[FLOATSZ];
dtostrfd(voltage, Settings.flag2.voltage_resolution, voltage_chr);
char current_chr[FLOATSZ];
dtostrfd(Adc[idx].current, Settings.flag2.current_resolution, current_chr);
char power_chr[FLOATSZ];
dtostrfd(voltage * Adc[idx].current, Settings.flag2.wattage_resolution, power_chr);
char energy_chr[FLOATSZ];
dtostrfd(Adc[idx].energy, Settings.flag2.energy_resolution, energy_chr);
if (json) {
AdcShowContinuation(&jsonflg);
ResponseAppend_P(PSTR("\"CTEnergy%s\":{\"" D_JSON_ENERGY "\":%s,\"" D_JSON_POWERUSAGE "\":%s,\"" D_JSON_VOLTAGE "\":%s,\"" D_JSON_CURRENT "\":%s}"),
adc_idx, energy_chr, power_chr, voltage_chr, current_chr);
#ifdef USE_DOMOTICZ
if ((0 == TasmotaGlobal.tele_period) && (!domo_flag[ADC_CT_POWER])) {
DomoticzSensor(DZ_POWER_ENERGY, power_chr);
DomoticzSensor(DZ_VOLTAGE, voltage_chr);
DomoticzSensor(DZ_CURRENT, current_chr);
domo_flag[ADC_CT_POWER] = true;
}
#endif // USE_DOMOTICZ
#ifdef USE_WEBSERVER
} else {
WSContentSend_PD(HTTP_SNS_VOLTAGE, voltage_chr);
WSContentSend_PD(HTTP_SNS_CURRENT, current_chr);
WSContentSend_PD(HTTP_SNS_POWER, power_chr);
WSContentSend_PD(HTTP_SNS_ENERGY_TOTAL, energy_chr);
#endif // USE_WEBSERVER
}
break;
}
case ADC_JOY: {
uint16_t new_value = AdcRead(Adc[idx].pin, 1);
uint16_t value = new_value / Adc[idx].param1;
if (json) {
AdcShowContinuation(&jsonflg);
ResponseAppend_P(PSTR("\"Joy%s\":%d"), adc_idx, value);
}
break;
}
case ADC_PH: {
float ph = AdcGetPh(idx);
char ph_chr[6];
dtostrfd(ph, 2, ph_chr);
if (json) {
AdcShowContinuation(&jsonflg);
ResponseAppend_P(PSTR("\"pH%d\":%s"), idx + offset, ph_chr);
#ifdef USE_WEBSERVER
} else {
WSContentSend_PD(HTTP_SNS_PH, "", ph_chr);
#endif // USE_WEBSERVER
}
break;
}
}
}
if (jsonflg) {
ResponseJsonEnd();
}
}
/*********************************************************************************************\
* Commands
\*********************************************************************************************/
const char kAdcCommands[] PROGMEM = "|" // No prefix
D_CMND_ADCPARAM;
void (* const AdcCommand[])(void) PROGMEM = {
&CmndAdcParam };
void CmndAdcParam(void) {
if ((XdrvMailbox.index > 0) && (XdrvMailbox.index <= MAX_ADCS)) {
uint8_t idx = XdrvMailbox.index -1;
if (XdrvMailbox.data_len) {
if (XdrvMailbox.payload > ADC_INPUT) {
AdcGetSettings(idx);
if (ArgC() > 3) { // Process parameter entry
char argument[XdrvMailbox.data_len];
// AdcParam 2, 32000, 10000, 3350
// AdcParam 3, 10000, 12518931, -1.405
// AdcParam 4, 128, 0, 0
// AdcParam 5, 128, 0, 0
// AdcParam 6, 0, ANALOG_RANGE, 0, 100
// AdcParam 7, 0, 2146, 0.23
// AdcParam 8, 1000, 0, 0
Adc[idx].type = XdrvMailbox.payload;
Adc[idx].param1 = strtol(ArgV(argument, 2), nullptr, 10);
Adc[idx].param2 = strtol(ArgV(argument, 3), nullptr, 10);
if (ADC_RANGE == XdrvMailbox.payload) {
Adc[idx].param3 = abs(strtol(ArgV(argument, 4), nullptr, 10));
Adc[idx].param4 = abs(strtol(ArgV(argument, 5), nullptr, 10));
} else {
Adc[idx].param3 = (int)(CharToFloat(ArgV(argument, 4)) * 10000);
}
if (ADC_PH == XdrvMailbox.payload) {
float phLow = CharToFloat(ArgV(argument, 2));
float phHigh = CharToFloat(ArgV(argument, 4));
Adc[idx].param1 = phLow * ANALOG_PH_DECIMAL_MULTIPLIER;
Adc[idx].param2 = strtol(ArgV(argument, 3), nullptr, 10);
Adc[idx].param3 = phHigh * ANALOG_PH_DECIMAL_MULTIPLIER;
Adc[idx].param4 = strtol(ArgV(argument, 5), nullptr, 10);
AddLog(LOG_LEVEL_INFO, PSTR(D_LOG_APPLICATION "Analog pH probe calibrated. cal-low(pH=ADC) %2_f=%d, cal-high(pH=ADC) %2_f=%d"),
&phLow, Adc[idx].param2, &phHigh, Adc[idx].param4);
}
if (ADC_CT_POWER == XdrvMailbox.payload) {
if (((1 == Adc[idx].param1) & CT_FLAG_ENERGY_RESET) > 0) {
for (uint32_t idx = 0; idx < MAX_ADCS; idx++) {
Adc[idx].energy = 0;
}
Adc[idx].param1 ^= CT_FLAG_ENERGY_RESET; // Cancel energy reset flag
}
}
} else { // Set default values based on current adc type
// AdcParam 2
// AdcParam 3
// AdcParam 4
// AdcParam 5
// AdcParam 6
// AdcParam 7
// AdcParam 8
Adcs.type = 0;
AdcInitParams(idx);
}
AdcSaveSettings(idx);
}
}
// AdcParam
AdcGetSettings(idx);
Response_P(PSTR("{\"" D_CMND_ADCPARAM "%d\":[%d,%d,%d"), idx +1, Adcs.type, Adc[idx].param1, Adc[idx].param2);
if (ADC_RANGE == Adc[idx].type) {
ResponseAppend_P(PSTR(",%d,%d"), Adc[idx].param3, Adc[idx].param4);
} else {
int value = Adc[idx].param3;
uint8_t precision;
for (precision = 4; precision > 0; precision--) {
if (value % 10) { break; }
value /= 10;
}
char param3[33];
dtostrfd(((double)Adc[idx].param3)/10000, precision, param3);
ResponseAppend_P(PSTR(",%s"), param3);
}
ResponseAppend_P(PSTR("]}"));
}
}
/*********************************************************************************************\
* Interface
\*********************************************************************************************/
bool Xsns02(uint8_t function) {
bool result = false;
switch (function) {
case FUNC_COMMAND:
result = DecodeCommand(kAdcCommands, AdcCommand);
break;
case FUNC_MODULE_INIT:
AdcInit();
break;
default:
if (Adcs.present) {
switch (function) {
#ifdef USE_RULES
case FUNC_EVERY_250_MSECOND:
AdcEvery250ms();
break;
#endif // USE_RULES
case FUNC_EVERY_SECOND:
AdcEverySecond();
break;
case FUNC_JSON_APPEND:
AdcShow(1);
break;
#ifdef USE_WEBSERVER
case FUNC_WEB_SENSOR:
AdcShow(0);
break;
#endif // USE_WEBSERVER
}
}
}
return result;
}
#endif // USE_ADC