/* xnrg_19_cse7761.ino - CSE7761 energy sensor support for Tasmota Copyright (C) 2021 Theo Arends This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ #ifdef USE_ENERGY_SENSOR #ifdef USE_CSE7761 /*********************************************************************************************\ * CSE7761 - Energy (Sonoff Dual R3 Pow) * * Based on datasheet from ChipSea \*********************************************************************************************/ #define XNRG_19 19 #define CSE7761_K1 2 // Current channel sampling resistance in milli Ohm #define CSE7761_K2 2 // Voltage divider resistance in 1k/1M #define CSE7761_2POWER22 4194304 #define CSE7761_2POWER23 8388608 #define CSE7761_2POWER31 2147483648 enum CSE7761 { RmsIAC, RmsIBC, RmsUC, PowerPAC, PowerPBC, PowerSC, EnergyAc, EnergyBC }; #include TasmotaSerial *Cse7761Serial = nullptr; struct { uint32_t voltage_rms = 0; uint32_t current_rms[2] = { 0 }; uint32_t active_power[2] = { 0 }; uint16_t coefficient[8] = { 0 }; uint8_t init = 0; bool found = false; } CSE7761Data; void Cse7761Write(uint32_t reg, uint32_t data) { uint8_t buffer[5]; buffer[0] = 0xA5; buffer[1] = reg; uint32_t len = 2; if (data) { if (data < 0xFF) { buffer[2] = data & 0xFF; len = 3; } else { buffer[2] = (data >> 8) & 0xFF; buffer[3] = data & 0xFF; len = 4; } uint8_t crc = 0; for (uint32_t i = 0; i < len; i++) { crc += buffer[i]; } buffer[len] = ~crc; len++; } Cse7761Serial->write(buffer, len); AddLog(LOG_LEVEL_DEBUG, PSTR("C61: Send %d, Data %*_H"), len, len, buffer); } uint32_t Cse7761Read(uint32_t reg, uint32_t request) { delay(3); Cse7761Write(reg, 0); uint8_t buffer[5]; uint32_t rcvd = 0; uint32_t timeout = millis() + 3; while (!TimeReached(timeout) && (rcvd <= request) && (rcvd <= sizeof(buffer))) { int value = Cse7761Serial->read(); if (value > -1) { buffer[rcvd++] = value; } } if (!rcvd) { AddLog(LOG_LEVEL_DEBUG, PSTR("C61: Rcvd %d"), rcvd); return 0; } AddLog(LOG_LEVEL_DEBUG, PSTR("C61: Rcvd %d, Data %*_H"), rcvd, rcvd, buffer); int result = 0; uint8_t crc = 0xA5 + reg; for (uint32_t i = 0; i < rcvd -1; i++) { result = (result << 8) | buffer[i]; crc += buffer[i]; } crc = ~crc; if (crc != buffer[rcvd]) { result = 0; } return result; } bool Cse7761ChipInit(void) { uint16_t calc_chksum = 0xFFFF; for (uint32_t i = 0; i < 8; i++) { CSE7761Data.coefficient[i] = Cse7761Read(0x70 + i, 2); calc_chksum += CSE7761Data.coefficient[i]; } uint16_t dummy = Cse7761Read(0x6E, 2); uint16_t coeff_chksum = Cse7761Read(0x6F, 2); if (calc_chksum != coeff_chksum) { AddLog(LOG_LEVEL_DEBUG, PSTR("C61: Coefficients invalid")); // return false; } delay(3); Cse7761Write(0xEA, 0xE5); // Enable write operation delay(5); uint8_t sys_status = Cse7761Read(0x43, 1); if (sys_status & 0x10) { // Write enable to protected registers (WREN) delay(3); /* System Control Register (SYSCON) Addr:0x00 Default value: 0x0A04 Bit name Function description 15-11 NC -, the default is 1 10 ADC2ON =1, means ADC current channel B is on (Sonoff Dual R3 Pow) =0, means ADC current channel B is closed 9 NC -, the default is 1. 8-6 PGAIB[2:0] Current channel B analog gain selection highest bit =1XX, PGA of current channel B=16 =011, PGA of current channel B=8 =010, PGA of current channel B=4 =001, PGA of current channel B=2 =000, PGA of current channel B=1 (Sonoff Dual R3 Pow) 5-3 PGAU[2:0] Highest bit of voltage channel analog gain selection =1XX, PGA of current channel U=16 =011, PGA of current channel U=8 =010, PGA of current channel U=4 =001, PGA of current channel U=2 (Sonoff Dual R3 Pow) =000, PGA of current channel U=1 2-0 PGAIA[2:0] Current channel A analog gain selection highest bit =1XX, PGA of current channel A=16 =011, PGA of current channel A=8 =010, PGA of current channel A=4 =001, PGA of current channel A=2 =000, PGA of current channel A=1 (Sonoff Dual R3 Pow) */ Cse7761Write(0x80, 0xFF04); // Set SYSCON /* Energy Measure Control Register (EMUCON) Addr:0x01 Default value: 0x0000 Bit name Function description 15-14 Tsensor_Step[1:0] Measurement steps of temperature sensor: =2'b00 The first step of temperature sensor measurement, the Offset of OP1 and OP2 is +/+. (Sonoff Dual R3 Pow) =2'b01 The second step of temperature sensor measurement, the Offset of OP1 and OP2 is +/-. =2'b10 The third step of temperature sensor measurement, the Offset of OP1 and OP2 is -/+. =2'b11 The fourth step of temperature sensor measurement, the Offset of OP1 and OP2 is -/-. After measuring these four results and averaging, the AD value of the current measured temperature can be obtained. 13 tensor_en Temperature measurement module control =0 when the temperature measurement module is closed; (Sonoff Dual R3 Pow) =1 when the temperature measurement module is turned on; 12 comp_off Comparator module close signal: =0 when the comparator module is in working state =1 when the comparator module is off (Sonoff Dual R3 Pow) 11-10 Pmode[1:0] Selection of active energy calculation method: Pmode =00, both positive and negative active energy participate in the accumulation, the accumulation method is algebraic sum mode, the reverse REVQ symbol indicates to active power; (Sonoff Dual R3 Pow) Pmode = 01, only accumulate positive active energy; Pmode = 10, both positive and negative active energy participate in the accumulation, and the accumulation method is absolute value method. No reverse active power indication; Pmode =11, reserved, the mode is the same as Pmode =00 9 NC - 8 ZXD1 The initial value of ZX output is 0, and different waveforms are output according to the configuration of ZXD1 and ZXD0: =0, it means that the ZX output changes only at the selected zero-crossing point (Sonoff Dual R3 Pow) =1, indicating that the ZX output changes at both the positive and negative zero crossings 7 ZXD0 =0, indicates that the positive zero-crossing point is selected as the zero-crossing detection signal (Sonoff Dual R3 Pow) =1, indicating that the negative zero-crossing point is selected as the zero-crossing detection signal 6 HPFIBOFF =0, enable current channel B digital high-pass filter (Sonoff Dual R3 Pow) =1, turn off the digital high-pass filter of current channel B 5 HPFIAOFF =0, enable current channel A digital high-pass filter (Sonoff Dual R3 Pow) =1, turn off the digital high-pass filter of current channel A 4 HPFUOFF =0, enable U channel digital high pass filter (Sonoff Dual R3 Pow) =1, turn off the U channel digital high-pass filter 3-2 NC - 1 PBRUN =1, enable PFB pulse output and active energy register accumulation; (Sonoff Dual R3 Pow) =0 (default), turn off PFB pulse output and active energy register accumulation. 0 PARUN =1, enable PFA pulse output and active energy register accumulation; (Sonoff Dual R3 Pow) =0 (default), turn off PFA pulse output and active energy register accumulation. */ Cse7761Write(0x81, 0x1003); // Set EMUCON /* Energy Measure Control Register (EMUCON2) Addr: 0x13 Default value: 0x0001 Bit name Function description 15-13 NC - 12 SDOCmos =1, SDO pin CMOS open-drain output (Sonoff Dual R3 Pow) =0, SDO pin CMOS output 11 EPB_CB Energy_PB clear signal control, the default is 0, and it needs to be configured to 1 in UART mode. Clear after reading is not supported in UART mode =1, Energy_PB will not be cleared after reading; (Sonoff Dual R3 Pow) =0, Energy_PB is cleared after reading; 10 EPA_CB Energy_PA clear signal control, the default is 0, it needs to be configured to 1 in UART mode, Clear after reading is not supported in UART mode =1, Energy_PA will not be cleared after reading; (Sonoff Dual R3 Pow) =0, Energy_PA is cleared after reading; 9-8 DUPSEL[1:0] Average register update frequency control =00, Update frequency 3.4Hz =01, Update frequency 6.8Hz =10, Update frequency 13.65Hz =11, Update frequency 27.3Hz (Sonoff Dual R3 Pow) 7 CHS_IB Current channel B measurement selection signal =1, measure the current of channel B (Sonoff Dual R3 Pow) =0, measure the internal temperature of the chip 6 PfactorEN Power factor function enable =1, turn on the power factor output function (Sonoff Dual R3 Pow) =0, turn off the power factor output function 5 WaveEN Waveform data, instantaneous data output enable signal =1, turn on the waveform data output function =0, turn off the waveform data output function (Sonoff Dual R3 Pow) 4 SAGEN Voltage drop detection enable signal, WaveEN=1 must be configured first =1, turn on the voltage drop detection function =0, turn off the voltage drop detection function (Sonoff Dual R3 Pow) 3 OverEN Overvoltage, overcurrent, and overload detection enable signal, WaveEN=1 must be configured first =1, turn on the overvoltage, overcurrent, and overload detection functions =0, turn off the overvoltage, overcurrent, and overload detection functions (Sonoff Dual R3 Pow) 2 ZxEN Zero-crossing detection, phase angle, voltage frequency measurement enable signal =1, turn on the zero-crossing detection, phase angle, and voltage frequency measurement functions =0, disable zero-crossing detection, phase angle, voltage frequency measurement functions (Sonoff Dual R3 Pow) 1 PeakEN Peak detect enable signal =1, turn on the peak detection function =0, turn off the peak detection function (Sonoff Dual R3 Pow) 0 NC Default is 1 */ Cse7761Write(0x93, 0x0FC1); // Set EMUCON2 } else { AddLog(LOG_LEVEL_DEBUG, PSTR("C61: Write enable failed")); // return false; } delay(80); Cse7761Write(0xEA, 0xDC); // Close write operation return true; } void Cse7761GetData(void) { CSE7761Data.voltage_rms = Cse7761Read(0x26, 3); CSE7761Data.current_rms[0] = Cse7761Read(0x24, 3); CSE7761Data.active_power[0] = Cse7761Read(0x2C, 4); CSE7761Data.current_rms[1] = Cse7761Read(0x25, 3); CSE7761Data.active_power[1] = Cse7761Read(0x2D, 4); if (Energy.power_on) { // Powered on Energy.voltage[0] = ((float)CSE7761Data.voltage_rms * ((double)CSE7761Data.coefficient[RmsUC] / (CSE7761_K2 * 2 * CSE7761_2POWER22))) / 1000; // V for (uint32_t channel = 0; channel < 2; channel++) { Energy.data_valid[channel] = 0; Energy.active_power[channel] = (float)CSE7761Data.active_power[channel] * ((double)CSE7761Data.coefficient[PowerPAC + channel] / (CSE7761_K1 * CSE7761_K2 * 2 * CSE7761_2POWER31)); // W if (0 == Energy.active_power[channel]) { Energy.current[channel] = 0; } else { Energy.current[channel] = (float)CSE7761Data.current_rms[channel] * ((double)CSE7761Data.coefficient[RmsIAC + channel] / (CSE7761_K1 * 2 * CSE7761_2POWER23)); // mA } } uint32_t active_power_sum = (Energy.active_power[0] + Energy.active_power[1]) * 1000; if (active_power_sum) { Energy.kWhtoday_delta += active_power_sum / 36; EnergyUpdateToday(); } } else { // Powered off Energy.data_valid[0] = ENERGY_WATCHDOG; Energy.data_valid[1] = ENERGY_WATCHDOG; } } /********************************************************************************************/ void Cse7761EverySecond(void) { if (CSE7761Data.init) { if (2 == CSE7761Data.init) { Cse7761Write(0xEA, 0x96); // Reset chip } else if (1 == CSE7761Data.init) { uint16_t syscon = Cse7761Read(0x00, 2); // Default 0x0A04 if (0x0A04 == syscon) { CSE7761Data.found = Cse7761ChipInit(); } if (CSE7761Data.found) { AddLog(LOG_LEVEL_INFO, PSTR("C61: CSE7761 found")); } } CSE7761Data.init--; } else { if (CSE7761Data.found) { Cse7761GetData(); } } } void Cse7761SnsInit(void) { // Software serial init needs to be done here as earlier (serial) interrupts may lead to Exceptions Cse7761Serial = new TasmotaSerial(Pin(GPIO_CSE7766_RX), Pin(GPIO_CSE7766_TX), 1); if (Cse7761Serial->begin(38400, SERIAL_8E1)) { if (Cse7761Serial->hardwareSerial()) { // SetSerial(38400, TS_SERIAL_8E1); ClaimSerial(); } } else { TasmotaGlobal.energy_driver = ENERGY_NONE; } } void Cse7761DrvInit(void) { if (PinUsed(GPIO_CSE7761_RX) && PinUsed(GPIO_CSE7761_TX)) { CSE7761Data.found = false; CSE7761Data.init = 3; // Init setup steps Energy.phase_count = 2; // Handle two channels as two phases Energy.voltage_common = true; // Use common voltage TasmotaGlobal.energy_driver = XNRG_19; } } /*********************************************************************************************\ * Interface \*********************************************************************************************/ bool Xnrg19(uint8_t function) { bool result = false; switch (function) { case FUNC_EVERY_SECOND: Cse7761EverySecond(); break; case FUNC_INIT: Cse7761SnsInit(); break; case FUNC_PRE_INIT: Cse7761DrvInit(); break; } return result; } #endif // USE_CSE7761 #endif // USE_ENERGY_SENSOR