diff --git a/Mirabella-Genio-Bulb.md b/Mirabella-Genio-Bulb.md
index 9284f1ac..82a3b005 100644
--- a/Mirabella-Genio-Bulb.md
+++ b/Mirabella-Genio-Bulb.md
@@ -1,13 +1,41 @@
 # Mirabella Genio Bulb
 Mirabella have released a few smart bulbs.
-Here is a bit of a guide on how to open them up and then flash with Tasmota.
+Here is a bit of a guide on how to flash them with Tasmota.
 
-I am no expert at this but so far it has worked for me.
+There are two ways: Over the Air (OTA) or via Serial.
+  
+## Flashing Over the Air
+Flashing over the air requires running a linux shell script called [tuya-convert](https://github.com/ct-Open-Source/tuya-convert) and hence requires a computer (I used a Raspberry PI 3) with a wifi adaptor that supports AP mode.  There are options if you run Windows to use either a virtual machine (it is reported that KALI Linux running on VMWare has worked) or potentially a live usb (I haven't tested it). 
+
+Follow this [procedure](https://github.com/ct-Open-Source/tuya-convert#procedure). 
+
+I used [tasmota-basic](https://github.com/arendst/Sonoff-Tasmota/releases/download/v6.4.1/sonoff-basic.bin) firmware instead of the custom tasmota-classic firmware included.  The benefit of tasmota-basic is the lightbulb will create an access point that you can connect to after it has been flashed for configuration.
+
+```
+pi@raspberrypi:~/src/tuya-convert/ $ cd files
+pi@raspberrypi:~/src/tuya-convert/files $ wget http://sonoff.maddox.co.uk/tasmota/sonoff-basic.bin
+--2019-01-25 07:54:52--  http://sonoff.maddox.co.uk/tasmota/sonoff-basic.bin
+Resolving sonoff.maddox.co.uk (sonoff.maddox.co.uk)... 139.59.203.138
+Connecting to sonoff.maddox.co.uk (sonoff.maddox.co.uk)|139.59.203.138|:80... connected.
+HTTP request sent, awaiting response... 200 OK
+Length: 456240 (446K) [application/octet-stream]
+Saving to: ‘sonoff-basic.bin’
+
+sonoff-basic.bin          100%[===================================>] 445.55K   312KB/s    in 1.4s
+
+2019-01-25 07:54:54 (312 KB/s) - ‘sonoff-basic.bin’ saved [456240/456240]
+
+pi@raspberrypi:~/src/tuya-convert/files $ rm thirdparty.bin
+pi@raspberrypi:~/src/tuya-convert/files $ ln -s sonoff-basic.bin thirdparty.bin
+```
+ 
+## Flashing via Serial
+Flashing via Serial requires disassembling the bulb and soldiering wires to the board.
 
 _Note: modifying these bulbs is dangerous if you do not understand what you are doing, please do so at your own risk!_
 
 [Mirabella Bulbs](https://mirabellagenio.net.au/bulbs)
-## Disassembling bulb
+### Disassembling bulb
 
 ![B22](https://i.ibb.co/HT7mc8B/B22-0-SM.jpg)
 
@@ -24,11 +52,11 @@ Carefully cut / scrape away as much of the sealent on the outer edge of the roun
 ![2](https://i.ibb.co/hmz7QGF/B22-2-SM.jpg)
 
 If you are really good at soldering and have a fine tip on your iron you could possibly skip this step and jump straight to the next one.
-### B22
+#### B22
 Stand the bulb up and de-solder the 2 pads, and straighten the wires to remove the board.
 
 ![3](https://i.ibb.co/56ys1r7/B22-3-SM.jpg)
-### E27
+#### E27
 Using a sharp strong blade carefully pry out the small terminal on the end of the bulb then straighten the wire in side
 
 ![E27](https://i.ibb.co/N9WTW5n/E27-1-SM.jpg)
@@ -39,17 +67,17 @@ This will allow you to pull the board out a little and get enough angle on it to
 
 You should now have these parts (E27 bulb will be still partly assembled):
 
-### B22
+#### B22
 
 ![4](https://i.ibb.co/rQZWVnB/B22-4-SM.jpg)
 
-### E27
+#### E27
 
 ![E27](https://i.ibb.co/Q9pqCsw/E27-3-SM.jpg)
 
 (with wires added)
 
-## Connect FTDI
+### Connect FTDI
 
 Connect your FTDI up to these pins: