diff --git a/Rules.md b/Rules.md
index 7a43e1a6..d1f66a77 100644
--- a/Rules.md
+++ b/Rules.md
@@ -187,13 +187,13 @@ VARx#State        | when a the value for a Variable is changed
 MEMx#State        | when a the value for a Persistent Variable is changed                     | 6.4.1.14
 
 #### Sensors
-All connected sensors can be a trigger in the form as they are represented in the teleperiod or Status 8 JSON message. The format is:
+All connected sensors can be a trigger in the form as they are represented in the TelePeriod or Status 8 JSON message. The format is:
 ```
 [SensorName]#[ValueName]
 ```
 Example triggers are:
 
-- ``Tele-AM2301#Temperature``triggers on the Teleperiod time for the sensor AM2301.
+- ``Tele-AM2301#Temperature``triggers on the TelePeriod time for the sensor AM2301.
 - ``Dsb18b20#Temperature<20`` whenever the temperature of sensor DSB18B20 is below 20 degrees
 - ``AM2301-12#Humidity=55.5`` whenever the hunidity of sensor AM2301-12 equals 55.5 %
 - ``INA219#Current>0.100`` whenever the current drawn is more than 0.1A
@@ -204,7 +204,7 @@ Devices using RfReceived (Sonoff Bridge) or IrReceived are also supported based
 - ``IrReceived#Data=801`` whenever an IR signal for a RC5 remote control button 1 is received (6.1.0)
 - ``RfReceived#RfKey=4`` whenever the Sonoff Bridge receives a recognized Rf signal (6.1.0)
 
-To trigger on a sensor at Teleperiod time only you may prefix the sensor with the word ``tele-`` to distinguish it from the above shown trigger. See example 5 below. 
+To trigger on a sensor at TelePeriod time only you may prefix the sensor with the word ``tele-`` to distinguish it from the above shown trigger. See example 5 below. 
 
 
 [BackToTop](https://github.com/arendst/Sonoff-Tasmota/wiki/Rules#summary)
@@ -606,7 +606,7 @@ Inital config on console:
 * `SwitchMode1 3`  <- Use the switch1 as pushbutton (It will allow us to disable the link between the button and the relay by inserting a rule to dictate what the pushbutton will do - **NOTE: Until rules are created the pushbutton will still control the relay!**)
 * `Rule 1 `        <- turn on rules
 * `Rule 4`        <- turn off one-shot rule
-* `teleperiod 60`  <- check temp every minute
+* `TelePeriod 60`  <- check temp every minute
 * `SetOption26 1`  <- use power1 on mqtt messages
 * `SetOption0 0`   <- dont save relay status on eeprom
 * `poweronstate 0` <- start all relays off
@@ -658,9 +658,9 @@ To get the status:
 
 Everything together:
 
-INITIAL CONFIG: (To note RuleTimer1 must be greater that teleperiod for expected results)
+INITIAL CONFIG: (To note RuleTimer1 must be greater that TelePeriod for expected results)
 
-`backlog SwitchMode1 3; Rule 1; Rule 4; teleperiod 60; SetOption26 1; SetOption0 0; poweronstate 0; mem1 0; mem2 25; mem3 23; var1 0`
+`backlog SwitchMode1 3; Rule 1; Rule 4; TelePeriod 60; SetOption26 1; SetOption0 0; poweronstate 0; mem1 0; mem2 25; mem3 23; var1 0`
 
 RULES: