From fabfacf3d714bffd253b52345c48ff974012ae87 Mon Sep 17 00:00:00 2001 From: iabdalkader Date: Wed, 21 Feb 2018 00:35:05 +0200 Subject: [PATCH] stm32/boards: Add new NUCLEO_H743ZI board configuration files. USB serial and mass storage works, and the REPL is also available via the UART through the on-board ST-LINK. --- ports/stm32/boards/NUCLEO_H743ZI/board_init.c | 15 + .../boards/NUCLEO_H743ZI/mpconfigboard.h | 57 +++ .../boards/NUCLEO_H743ZI/mpconfigboard.mk | 6 + ports/stm32/boards/NUCLEO_H743ZI/pins.csv | 59 +++ .../boards/NUCLEO_H743ZI/stm32h7xx_hal_conf.h | 434 ++++++++++++++++++ 5 files changed, 571 insertions(+) create mode 100644 ports/stm32/boards/NUCLEO_H743ZI/board_init.c create mode 100644 ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.h create mode 100644 ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.mk create mode 100644 ports/stm32/boards/NUCLEO_H743ZI/pins.csv create mode 100644 ports/stm32/boards/NUCLEO_H743ZI/stm32h7xx_hal_conf.h diff --git a/ports/stm32/boards/NUCLEO_H743ZI/board_init.c b/ports/stm32/boards/NUCLEO_H743ZI/board_init.c new file mode 100644 index 0000000000..1a6006c280 --- /dev/null +++ b/ports/stm32/boards/NUCLEO_H743ZI/board_init.c @@ -0,0 +1,15 @@ +#include STM32_HAL_H + +void NUCLEO_H743ZI_board_early_init(void) { + GPIO_InitTypeDef GPIO_InitStructure; + + __HAL_RCC_GPIOG_CLK_ENABLE(); + + // Turn off the USB switch + GPIO_InitStructure.Pin = GPIO_PIN_6; + GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStructure.Pull = GPIO_PULLDOWN; + GPIO_InitStructure.Speed = GPIO_SPEED_FREQ_LOW; + HAL_GPIO_Init(GPIOG, &GPIO_InitStructure); + HAL_GPIO_WritePin(GPIOG, GPIO_PIN_6, GPIO_PIN_RESET); +} diff --git a/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.h b/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.h new file mode 100644 index 0000000000..4fe41e0a1b --- /dev/null +++ b/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.h @@ -0,0 +1,57 @@ +#define MICROPY_HW_BOARD_NAME "NUCLEO_H743ZI" +#define MICROPY_HW_MCU_NAME "STM32H743" + +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_ADC (0) +#define MICROPY_HW_ENABLE_USB (1) +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_FLASH (1) + +#define MICROPY_BOARD_EARLY_INIT NUCLEO_H743ZI_board_early_init +void NUCLEO_H743ZI_board_early_init(void); + +// The board has an 8MHz HSE, the following gives 400MHz CPU speed +#define MICROPY_HW_CLK_PLLM (4) +#define MICROPY_HW_CLK_PLLN (400) +#define MICROPY_HW_CLK_PLLP (2) +#define MICROPY_HW_CLK_PLLQ (4) +#define MICROPY_HW_CLK_PLLR (2) + +// 4 wait states +#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4 + +// UART config +#define MICROPY_HW_UART3_TX (pin_D8) +#define MICROPY_HW_UART3_RX (pin_D9) +#define MICROPY_HW_UART_REPL PYB_UART_3 +#define MICROPY_HW_UART_REPL_BAUD 115200 + +// I2C busses +//#define MICROPY_HW_I2C1_SCL (pin_B8) +//#define MICROPY_HW_I2C1_SDA (pin_B9) +//#define MICROPY_HW_I2C3_SCL (pin_H7) +//#define MICROPY_HW_I2C3_SDA (pin_H8) + +// SPI +//#define MICROPY_HW_SPI2_NSS (pin_I0) +//#define MICROPY_HW_SPI2_SCK (pin_I1) +//#define MICROPY_HW_SPI2_MISO (pin_B14) +//#define MICROPY_HW_SPI2_MOSI (pin_B15) + +// USRSW is pulled low. Pressing the button makes the input go high. +#define MICROPY_HW_USRSW_PIN (pin_C13) +#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) +#define MICROPY_HW_USRSW_PRESSED (1) + +// LEDs +#define MICROPY_HW_LED1 (pin_B0) // green +#define MICROPY_HW_LED2 (pin_B7) // blue +#define MICROPY_HW_LED3 (pin_B14) // red +#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) +#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) + +// USB config +#define MICROPY_HW_USB_FS (1) +#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) +#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10) diff --git a/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.mk b/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.mk new file mode 100644 index 0000000000..82b12cd2da --- /dev/null +++ b/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.mk @@ -0,0 +1,6 @@ +MCU_SERIES = h7 +CMSIS_MCU = STM32H743xx +MICROPY_FLOAT_IMPL = double +AF_FILE = boards/stm32h743_af.csv +LD_FILE = boards/stm32h743.ld +TEXT_ADDR = 0x08040000 diff --git a/ports/stm32/boards/NUCLEO_H743ZI/pins.csv b/ports/stm32/boards/NUCLEO_H743ZI/pins.csv new file mode 100644 index 0000000000..b0d225368c --- /dev/null +++ b/ports/stm32/boards/NUCLEO_H743ZI/pins.csv @@ -0,0 +1,59 @@ +A0,PA0 +A1,PF10 +A2,PF9 +A3,PF8 +A4,PF7 +A5,PF6 +D0,PC7 +D1,PC6 +D2,PG6 +D3,PB4 +D4,PG7 +D5,PA8 +D6,PH6 +D7,PI3 +D8,PI2 +D9,PA15 +D10,PI0 +D11,PB15 +D12,PB14 +D13,PI1 +D14,PB9 +D15,PB8 +LED1,PB0 +LED2,PB7 +LED3,PB14 +SW,PC13 +TP1,PH2 +TP2,PI8 +TP3,PH15 +AUDIO_INT,PD6 +AUDIO_SDA,PH8 +AUDIO_SCL,PH7 +EXT_SDA,PB9 +EXT_SCL,PB8 +EXT_RST,PG3 +SD_D0,PG9 +SD_D1,PG10 +SD_D2,PB3 +SD_D3,PB4 +SD_CK,PD6 +SD_CMD,PD7 +SD_SW,PI15 +LCD_BL_CTRL,PK3 +LCD_INT,PI13 +LCD_SDA,PH8 +LCD_SCL,PH7 +OTG_FS_POWER,PD5 +OTG_FS_OVER_CURRENT,PD4 +OTG_HS_OVER_CURRENT,PE3 +USB_VBUS,PJ12 +USB_ID,PA8 +USB_DM,PA11 +USB_DP,PA12 +UART1_TX,PA9 +UART1_RX,PA10 +UART5_TX,PC12 +UART5_RX,PD2 +UART3_TX,PD8 +UART3_RX,PD9 diff --git a/ports/stm32/boards/NUCLEO_H743ZI/stm32h7xx_hal_conf.h b/ports/stm32/boards/NUCLEO_H743ZI/stm32h7xx_hal_conf.h new file mode 100644 index 0000000000..89421d30b7 --- /dev/null +++ b/ports/stm32/boards/NUCLEO_H743ZI/stm32h7xx_hal_conf.h @@ -0,0 +1,434 @@ +/** + ****************************************************************************** + * @file stm32h7xx_hal_conf_template.h + * @author MCD Application Team + * @version V1.2.0 + * @date 29-December-2017 + * @brief HAL configuration template file. + * This file should be copied to the application folder and renamed + * to stm32h7xx_hal_conf.h. + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2017 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32H7xx_HAL_CONF_H +#define __STM32H7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +#define HAL_CEC_MODULE_ENABLED +#define HAL_COMP_MODULE_ENABLED +#define HAL_CORTEX_MODULE_ENABLED +#define HAL_CRC_MODULE_ENABLED +#define HAL_CRYP_MODULE_ENABLED +#define HAL_DAC_MODULE_ENABLED +#define HAL_DCMI_MODULE_ENABLED +#define HAL_DFSDM_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_DMA2D_MODULE_ENABLED +#define HAL_ETH_MODULE_ENABLED +#define HAL_FDCAN_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +#define HAL_HASH_MODULE_ENABLED +#define HAL_HCD_MODULE_ENABLED +#define HAL_HRTIM_MODULE_ENABLED +#define HAL_HSEM_MODULE_ENABLED +#define HAL_I2C_MODULE_ENABLED +#define HAL_I2S_MODULE_ENABLED +#define HAL_IRDA_MODULE_ENABLED +#define HAL_IWDG_MODULE_ENABLED +#define HAL_JPEG_MODULE_ENABLED +#define HAL_LPTIM_MODULE_ENABLED +#define HAL_LTDC_MODULE_ENABLED +#define HAL_MDIOS_MODULE_ENABLED +#define HAL_MDMA_MODULE_ENABLED +#define HAL_MMC_MODULE_ENABLED +#define HAL_NAND_MODULE_ENABLED +#define HAL_NOR_MODULE_ENABLED +#define HAL_OPAMP_MODULE_ENABLED +#define HAL_PCD_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_QSPI_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +#define HAL_RNG_MODULE_ENABLED +#define HAL_RTC_MODULE_ENABLED +#define HAL_SAI_MODULE_ENABLED +#define HAL_SD_MODULE_ENABLED +#define HAL_SDRAM_MODULE_ENABLED +#define HAL_SMARTCARD_MODULE_ENABLED +#define HAL_SMBUS_MODULE_ENABLED +#define HAL_SPDIFRX_MODULE_ENABLED +#define HAL_SPI_MODULE_ENABLED +#define HAL_SRAM_MODULE_ENABLED +#define HAL_SWPMI_MODULE_ENABLED +#define HAL_TIM_MODULE_ENABLED +#define HAL_UART_MODULE_ENABLED +#define HAL_USART_MODULE_ENABLED +#define HAL_WWDG_MODULE_ENABLED + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +#define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal oscillator (CSI) default value. + * This value is the default CSI value after Reset. + */ +#if !defined (CSI_VALUE) + #define CSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* CSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)64000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External clock in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0F) /*!< tick interrupt priority */ +#define USE_RTOS 0 +#define USE_SD_TRANSCEIVER 1U /*!< use uSD Transceiver */ + +/* ########################### Ethernet Configuration ######################### */ +#define ETH_TX_DESC_CNT 4 /* number of Ethernet Tx DMA descriptors */ +#define ETH_RX_DESC_CNT 4 /* number of Ethernet Rx DMA descriptors */ + +#define ETH_MAC_ADDR0 ((uint8_t)0x02) +#define ETH_MAC_ADDR1 ((uint8_t)0x00) +#define ETH_MAC_ADDR2 ((uint8_t)0x00) +#define ETH_MAC_ADDR3 ((uint8_t)0x00) +#define ETH_MAC_ADDR4 ((uint8_t)0x00) +#define ETH_MAC_ADDR5 ((uint8_t)0x00) + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + +/* ################## SPI peripheral configuration ########################## */ +/** + * @brief Used to activate CRC feature inside HAL SPI Driver + * Activated (1U): CRC code is compiled within HAL SPI driver + * Deactivated (0U): CRC code excluded from HAL SPI driver + */ + +#define USE_SPI_CRC 1U + + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32h7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32h7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32h7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32h7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32h7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32h7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32h7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32h7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32h7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32h7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_FDCAN_MODULE_ENABLED + #include "stm32h7xx_hal_fdcan.h" +#endif /* HAL_FDCAN_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32h7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32h7xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32h7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32h7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32h7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32h7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_HRTIM_MODULE_ENABLED + #include "stm32h7xx_hal_hrtim.h" +#endif /* HAL_HRTIM_MODULE_ENABLED */ + +#ifdef HAL_HSEM_MODULE_ENABLED + #include "stm32h7xx_hal_hsem.h" +#endif /* HAL_HSEM_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32h7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32h7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32h7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32h7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32h7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32h7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32h7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32h7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +#ifdef HAL_MDMA_MODULE_ENABLED + #include "stm32h7xx_hal_mdma.h" +#endif /* HAL_MDMA_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED + #include "stm32h7xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32h7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED +#include "stm32h7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_OPAMP_MODULE_ENABLED +#include "stm32h7xx_hal_opamp.h" +#endif /* HAL_OPAMP_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32h7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32h7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32h7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32h7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32h7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32h7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32h7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32h7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32h7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SWPMI_MODULE_ENABLED + #include "stm32h7xx_hal_swpmi.h" +#endif /* HAL_SWPMI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32h7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32h7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32h7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32h7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32h7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32h7xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32h7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32h7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32h7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32H7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/