**************************************** :mod:`network` --- network configuration **************************************** .. module:: network :synopsis: network configuration This module provides network drivers and routing configuration. To use this module, a MicroPython variant/build with network capabilities must be installed. Network drivers for specific hardware are available within this module and are used to configure hardware network interface(s). Network services provided by configured interfaces are then available for use via the :mod:`socket` module. For example:: # connect/ show IP config a specific network interface # see below for examples of specific drivers import network import time nic = network.Driver(...) if not nic.isconnected(): nic.connect() print("Waiting for connection...") while not nic.isconnected(): time.sleep(1) print(nic.ifconfig()) # now use socket as usual import socket addr = socket.getaddrinfo('micropython.org', 80)[0][-1] s = socket.socket() s.connect(addr) s.send(b'GET / HTTP/1.1\r\nHost: micropython.org\r\n\r\n') data = s.recv(1000) s.close() Common network adapter interface ================================ This section describes an (implied) abstract base class for all network interface classes implemented by :term:`MicroPython ports ` for different hardware. This means that MicroPython does not actually provide ``AbstractNIC`` class, but any actual NIC class, as described in the following sections, implements methods as described here. .. class:: AbstractNIC(id=None, ...) Instantiate a network interface object. Parameters are network interface dependent. If there are more than one interface of the same type, the first parameter should be `id`. .. method:: AbstractNIC.active([is_active]) Activate ("up") or deactivate ("down") the network interface, if a boolean argument is passed. Otherwise, query current state if no argument is provided. Most other methods require an active interface (behaviour of calling them on inactive interface is undefined). .. method:: AbstractNIC.connect([service_id, key=None, *, ...]) Connect the interface to a network. This method is optional, and available only for interfaces which are not "always connected". If no parameters are given, connect to the default (or the only) service. If a single parameter is given, it is the primary identifier of a service to connect to. It may be accompanied by a key (password) required to access said service. There can be further arbitrary keyword-only parameters, depending on the networking medium type and/or particular device. Parameters can be used to: a) specify alternative service identifier types; b) provide additional connection parameters. For various medium types, there are different sets of predefined/recommended parameters, among them: * WiFi: *bssid* keyword to connect to a specific BSSID (MAC address) .. method:: AbstractNIC.disconnect() Disconnect from network. .. method:: AbstractNIC.isconnected() Returns ``True`` if connected to network, otherwise returns ``False``. .. method:: AbstractNIC.scan(*, ...) Scan for the available network services/connections. Returns a list of tuples with discovered service parameters. For various network media, there are different variants of predefined/ recommended tuple formats, among them: * WiFi: (ssid, bssid, channel, RSSI, security, hidden). There may be further fields, specific to a particular device. The function may accept additional keyword arguments to filter scan results (e.g. scan for a particular service, on a particular channel, for services of a particular set, etc.), and to affect scan duration and other parameters. Where possible, parameter names should match those in connect(). .. method:: AbstractNIC.status([param]) Query dynamic status information of the interface. When called with no argument the return value describes the network link status. Otherwise *param* should be a string naming the particular status parameter to retrieve. The return types and values are dependent on the network medium/technology. Some of the parameters that may be supported are: * WiFi STA: use ``'rssi'`` to retrieve the RSSI of the AP signal * WiFi AP: use ``'stations'`` to retrieve a list of all the STAs connected to the AP. The list contains tuples of the form (MAC, RSSI). .. method:: AbstractNIC.ifconfig([(ip, subnet, gateway, dns)]) Get/set IP-level network interface parameters: IP address, subnet mask, gateway and DNS server. When called with no arguments, this method returns a 4-tuple with the above information. To set the above values, pass a 4-tuple with the required information. For example:: nic.ifconfig(('192.168.0.4', '255.255.255.0', '192.168.0.1', '8.8.8.8')) .. method:: AbstractNIC.config('param') AbstractNIC.config(param=value, ...) Get or set general network interface parameters. These methods allow to work with additional parameters beyond standard IP configuration (as dealt with by `ifconfig()`). These include network-specific and hardware-specific parameters. For setting parameters, the keyword argument syntax should be used, and multiple parameters can be set at once. For querying, a parameter name should be quoted as a string, and only one parameter can be queried at a time:: # Set WiFi access point name (formally known as SSID) and WiFi channel ap.config(ssid='My AP', channel=11) # Query params one by one print(ap.config('ssid')) print(ap.config('channel')) Specific network class implementations ====================================== The following concrete classes implement the AbstractNIC interface and provide a way to control networking interfaces of various kinds. .. toctree:: :maxdepth: 1 network.WLAN.rst network.WLANWiPy.rst network.WIZNET5K.rst network.LAN.rst Network functions ================= The following are functions available in the network module. .. function:: country([code]) Get or set the two-letter ISO 3166-1 Alpha-2 country code to be used for radio compliance. If the *code* parameter is provided, the country will be set to this value. If the function is called without parameters, it returns the current country. The default code ``"XX"`` represents the "worldwide" region. .. function:: hostname([name]) Get or set the hostname that will identify this device on the network. It will be used by all interfaces. This hostname is used for: * Sending to the DHCP server in the client request. (If using DHCP) * Broadcasting via mDNS. (If enabled) If the *name* parameter is provided, the hostname will be set to this value. If the function is called without parameters, it returns the current hostname. A change in hostname is typically only applied during connection. For DHCP this is because the hostname is part of the DHCP client request, and the implementation of mDNS in most ports only initialises the hostname once during connection. For this reason, you must set the hostname before activating/connecting your network interfaces. The default hostname is typically the name of the board. .. function:: phy_mode([mode]) Get or set the PHY mode. If the *mode* parameter is provided, the PHY mode will be set to this value. If the function is called without parameters, it returns the current PHY mode. The possible modes are defined as constants: * ``MODE_11B`` -- IEEE 802.11b, * ``MODE_11G`` -- IEEE 802.11g, * ``MODE_11N`` -- IEEE 802.11n. Availability: ESP8266.