.. currentmodule:: esp32 :mod:`esp32` --- functionality specific to the ESP32 ==================================================== .. module:: esp32 :synopsis: functionality specific to the ESP32 The ``esp32`` module contains functions and classes specifically aimed at controlling ESP32 modules. Functions --------- .. function:: wake_on_touch(wake) Configure whether or not a touch will wake the device from sleep. *wake* should be a boolean value. .. function:: wake_on_ulp(wake) Configure whether or not the Ultra-Low-Power co-processor can wake the device from sleep. *wake* should be a boolean value. .. function:: wake_on_ext0(pin, level) Configure how EXT0 wakes the device from sleep. *pin* can be ``None`` or a valid Pin object. *level* should be ``esp32.WAKEUP_ALL_LOW`` or ``esp32.WAKEUP_ANY_HIGH``. .. function:: wake_on_ext1(pins, level) Configure how EXT1 wakes the device from sleep. *pins* can be ``None`` or a tuple/list of valid Pin objects. *level* should be ``esp32.WAKEUP_ALL_LOW`` or ``esp32.WAKEUP_ANY_HIGH``. .. function:: gpio_deep_sleep_hold(enable) Configure whether non-RTC GPIO pin configuration is retained during deep-sleep mode for held pads. *enable* should be a boolean value. .. function:: raw_temperature() Read the raw value of the internal temperature sensor, returning an integer. .. function:: idf_heap_info(capabilities) Returns information about the ESP-IDF heap memory regions. One of them contains the MicroPython heap and the others are used by ESP-IDF, e.g., for network buffers and other data. This data is useful to get a sense of how much memory is available to ESP-IDF and the networking stack in particular. It may shed some light on situations where ESP-IDF operations fail due to allocation failures. The capabilities parameter corresponds to ESP-IDF's ``MALLOC_CAP_XXX`` values but the two most useful ones are predefined as `esp32.HEAP_DATA` for data heap regions and `esp32.HEAP_EXEC` for executable regions as used by the native code emitter. The return value is a list of 4-tuples, where each 4-tuple corresponds to one heap and contains: the total bytes, the free bytes, the largest free block, and the minimum free seen over time. Example after booting:: >>> import esp32; esp32.idf_heap_info(esp32.HEAP_DATA) [(240, 0, 0, 0), (7288, 0, 0, 0), (16648, 4, 4, 4), (79912, 35712, 35512, 35108), (15072, 15036, 15036, 15036), (113840, 0, 0, 0)] .. note:: Free IDF heap memory in the `esp32.HEAP_DATA` region is available to be automatically added to the MicroPython heap to prevent a MicroPython allocation from failing. However, the information returned here is otherwise *not* useful to troubleshoot Python allocation failures. :func:`micropython.mem_info()` and :func:`gc.mem_free()` should be used instead: The "max new split" value in :func:`micropython.mem_info()` output corresponds to the largest free block of ESP-IDF heap that could be automatically added on demand to the MicroPython heap. The result of :func:`gc.mem_free()` is the total of the current "free" and "max new split" values printed by :func:`micropython.mem_info()`. Flash partitions ---------------- This class gives access to the partitions in the device's flash memory and includes methods to enable over-the-air (OTA) updates. .. class:: Partition(id, block_size=4096, /) Create an object representing a partition. *id* can be a string which is the label of the partition to retrieve, or one of the constants: ``BOOT`` or ``RUNNING``. *block_size* specifies the byte size of an individual block. .. classmethod:: Partition.find(type=TYPE_APP, subtype=0xff, label=None, block_size=4096) Find a partition specified by *type*, *subtype* and *label*. Returns a (possibly empty) list of Partition objects. Note: ``subtype=0xff`` matches any subtype and ``label=None`` matches any label. *block_size* specifies the byte size of an individual block used by the returned objects. .. method:: Partition.info() Returns a 6-tuple ``(type, subtype, addr, size, label, encrypted)``. .. method:: Partition.readblocks(block_num, buf) Partition.readblocks(block_num, buf, offset) .. method:: Partition.writeblocks(block_num, buf) Partition.writeblocks(block_num, buf, offset) .. method:: Partition.ioctl(cmd, arg) These methods implement the simple and :ref:`extended ` block protocol defined by :class:`os.AbstractBlockDev`. .. method:: Partition.set_boot() Sets the partition as the boot partition. .. note:: Do not enter :func:`deepsleep` after changing the OTA boot partition, without first performing a hard :func:`reset` or power cycle. This ensures the bootloader will validate the new image before booting. .. method:: Partition.get_next_update() Gets the next update partition after this one, and returns a new Partition object. Typical usage is ``Partition(Partition.RUNNING).get_next_update()`` which returns the next partition to update given the current running one. .. classmethod:: Partition.mark_app_valid_cancel_rollback() Signals that the current boot is considered successful. Calling ``mark_app_valid_cancel_rollback`` is required on the first boot of a new partition to avoid an automatic rollback at the next boot. This uses the ESP-IDF "app rollback" feature with "CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE" and an ``OSError(-261)`` is raised if called on firmware that doesn't have the feature enabled. It is OK to call ``mark_app_valid_cancel_rollback`` on every boot and it is not necessary when booting firmware that was loaded using esptool. Constants ~~~~~~~~~ .. data:: Partition.BOOT Partition.RUNNING Used in the `Partition` constructor to fetch various partitions: ``BOOT`` is the partition that will be booted at the next reset and ``RUNNING`` is the currently running partition. .. data:: Partition.TYPE_APP Partition.TYPE_DATA Used in `Partition.find` to specify the partition type: ``APP`` is for bootable firmware partitions (typically labelled ``factory``, ``ota_0``, ``ota_1``), and ``DATA`` is for other partitions, e.g. ``nvs``, ``otadata``, ``phy_init``, ``vfs``. .. data:: HEAP_DATA HEAP_EXEC Used in `idf_heap_info`. .. _esp32.RMT: RMT --- The RMT (Remote Control) module, specific to the ESP32, was originally designed to send and receive infrared remote control signals. However, due to a flexible design and very accurate (as low as 12.5ns) pulse generation, it can also be used to transmit or receive many other types of digital signals:: import esp32 from machine import Pin r = esp32.RMT(0, pin=Pin(18), clock_div=8) r # RMT(channel=0, pin=18, source_freq=80000000, clock_div=8, idle_level=0) # To apply a carrier frequency to the high output r = esp32.RMT(0, pin=Pin(18), clock_div=8, tx_carrier=(38000, 50, 1)) # The channel resolution is 100ns (1/(source_freq/clock_div)). r.write_pulses((1, 20, 2, 40), 0) # Send 0 for 100ns, 1 for 2000ns, 0 for 200ns, 1 for 4000ns The input to the RMT module is an 80MHz clock (in the future it may be able to configure the input clock but, for now, it's fixed). ``clock_div`` *divides* the clock input which determines the resolution of the RMT channel. The numbers specified in ``write_pulses`` are multiplied by the resolution to define the pulses. ``clock_div`` is an 8-bit divider (0-255) and each pulse can be defined by multiplying the resolution by a 15-bit (0-32,768) number. There are eight channels (0-7) and each can have a different clock divider. So, in the example above, the 80MHz clock is divided by 8. Thus the resolution is (1/(80Mhz/8)) 100ns. Since the ``start`` level is 0 and toggles with each number, the bitstream is ``0101`` with durations of [100ns, 2000ns, 100ns, 4000ns]. For more details see Espressif's `ESP-IDF RMT documentation. `_. .. Warning:: The current MicroPython RMT implementation lacks some features, most notably receiving pulses. RMT should be considered a *beta feature* and the interface may change in the future. .. class:: RMT(channel, *, pin=None, clock_div=8, idle_level=False, tx_carrier=None) This class provides access to one of the eight RMT channels. *channel* is required and identifies which RMT channel (0-7) will be configured. *pin*, also required, configures which Pin is bound to the RMT channel. *clock_div* is an 8-bit clock divider that divides the source clock (80MHz) to the RMT channel allowing the resolution to be specified. *idle_level* specifies what level the output will be when no transmission is in progress and can be any value that converts to a boolean, with ``True`` representing high voltage and ``False`` representing low. To enable the transmission carrier feature, *tx_carrier* should be a tuple of three positive integers: carrier frequency, duty percent (``0`` to ``100``) and the output level to apply the carrier to (a boolean as per *idle_level*). .. classmethod:: RMT.source_freq() Returns the source clock frequency. Currently the source clock is not configurable so this will always return 80MHz. .. method:: RMT.clock_div() Return the clock divider. Note that the channel resolution is ``1 / (source_freq / clock_div)``. .. method:: RMT.wait_done(*, timeout=0) Returns ``True`` if the channel is idle or ``False`` if a sequence of pulses started with `RMT.write_pulses` is being transmitted. If the *timeout* keyword argument is given then block for up to this many milliseconds for transmission to complete. .. method:: RMT.loop(enable_loop) Configure looping on the channel. *enable_loop* is bool, set to ``True`` to enable looping on the *next* call to `RMT.write_pulses`. If called with ``False`` while a looping sequence is currently being transmitted then the current loop iteration will be completed and then transmission will stop. .. method:: RMT.write_pulses(duration, data=True) Begin transmitting a sequence. There are three ways to specify this: **Mode 1:** *duration* is a list or tuple of durations. The optional *data* argument specifies the initial output level. The output level will toggle after each duration. **Mode 2:** *duration* is a positive integer and *data* is a list or tuple of output levels. *duration* specifies a fixed duration for each. **Mode 3:** *duration* and *data* are lists or tuples of equal length, specifying individual durations and the output level for each. Durations are in integer units of the channel resolution (as described above), between 1 and 32767 units. Output levels are any value that can be converted to a boolean, with ``True`` representing high voltage and ``False`` representing low. If transmission of an earlier sequence is in progress then this method will block until that transmission is complete before beginning the new sequence. If looping has been enabled with `RMT.loop`, the sequence will be repeated indefinitely. Further calls to this method will block until the end of the current loop iteration before immediately beginning to loop the new sequence of pulses. Looping sequences longer than 126 pulses is not supported by the hardware. .. staticmethod:: RMT.bitstream_channel([value]) Select which RMT channel is used by the `machine.bitstream` implementation. *value* can be ``None`` or a valid RMT channel number. The default RMT channel is the highest numbered one. Passing in ``None`` disables the use of RMT and instead selects a bit-banging implementation for `machine.bitstream`. Passing in no argument will not change the channel. This function returns the current channel number. Ultra-Low-Power co-processor ---------------------------- This class gives access to the Ultra Low Power (ULP) co-processor on the ESP32, ESP32-S2 and ESP32-S3 chips. .. warning:: This class does not provide access to the RISCV ULP co-processor available on the ESP32-S2 and ESP32-S3 chips. .. class:: ULP() This class provides access to the Ultra-Low-Power co-processor. .. method:: ULP.set_wakeup_period(period_index, period_us) Set the wake-up period. .. method:: ULP.load_binary(load_addr, program_binary) Load a *program_binary* into the ULP at the given *load_addr*. .. method:: ULP.run(entry_point) Start the ULP running at the given *entry_point*. Constants --------- .. data:: esp32.WAKEUP_ALL_LOW esp32.WAKEUP_ANY_HIGH Selects the wake level for pins. Non-Volatile Storage -------------------- This class gives access to the Non-Volatile storage managed by ESP-IDF. The NVS is partitioned into namespaces and each namespace contains typed key-value pairs. The keys are strings and the values may be various integer types, strings, and binary blobs. The driver currently only supports 32-bit signed integers and blobs. .. warning:: Changes to NVS need to be committed to flash by calling the commit method. Failure to call commit results in changes being lost at the next reset. .. class:: NVS(namespace) Create an object providing access to a namespace (which is automatically created if not present). .. method:: NVS.set_i32(key, value) Sets a 32-bit signed integer value for the specified key. Remember to call *commit*! .. method:: NVS.get_i32(key) Returns the signed integer value for the specified key. Raises an OSError if the key does not exist or has a different type. .. method:: NVS.set_blob(key, value) Sets a binary blob value for the specified key. The value passed in must support the buffer protocol, e.g. bytes, bytearray, str. (Note that esp-idf distinguishes blobs and strings, this method always writes a blob even if a string is passed in as value.) Remember to call *commit*! .. method:: NVS.get_blob(key, buffer) Reads the value of the blob for the specified key into the buffer, which must be a bytearray. Returns the actual length read. Raises an OSError if the key does not exist, has a different type, or if the buffer is too small. .. method:: NVS.erase_key(key) Erases a key-value pair. .. method:: NVS.commit() Commits changes made by *set_xxx* methods to flash.