Tasmota/lib/lib_div/stm32flash-1.0-tasmota/stm32flash.h

/*
  stm32flash - Open Source ST STM32 flash program for Arduino
  Copyright (C) 2010 Geoffrey McRae <geoff@spacevs.com>

  This program is free software; you can redistribute it and/or
  modify it under the terms of the GNU General Public License
  as published by the Free Software Foundation; either version 2
  of the License, or (at your option) any later version.

  This program is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with this program; if not, write to the Free Software
  Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
*/


#ifndef STM32_FLASH_H
#define STM32_FLASH_H

#include <stdint.h>
#include <Stream.h>

/* flags */
#define STREAM_OPT_BYTE	(1 << 0)	/* byte (not frame) oriented */
#define STREAM_OPT_GVR_ETX	(1 << 1)	/* cmd GVR returns protection status */
#define STREAM_OPT_CMD_INIT	(1 << 2)	/* use INIT cmd to autodetect speed */
#define STREAM_OPT_RETRY	(1 << 3)	/* allowed read() retry after timeout */
#define STREAM_OPT_I2C	(1 << 4)	/* i2c */
#define STREAM_OPT_STRETCH_W	(1 << 5)	/* warning for no-stretching commands */

#define STREAM_SERIAL (STREAM_OPT_BYTE | STREAM_OPT_GVR_ETX | STREAM_OPT_CMD_INIT | STREAM_OPT_RETRY)
#define STREAM_I2C (STREAM_OPT_I2C | STREAM_OPT_STRETCH_W)

#define STM32_MAX_RX_FRAME	256	/* cmd read memory */
#define STM32_MAX_TX_FRAME	(1 + 256 + 1)	/* cmd write memory */

#define STM32_MAX_PAGES		0x0000ffff
#define STM32_MASS_ERASE	0x00100000 /* > 2 x max_pages */

typedef enum {
	STM32_ERR_OK = 0,
	STM32_ERR_UNKNOWN,	/* Generic error */
	STM32_ERR_NACK,
	STM32_ERR_NO_CMD,	/* Command not available in bootloader */
} stm32_err_t;

typedef enum {
	F_NO_ME = 1 << 0,	/* Mass-Erase not supported */
	F_OBLL  = 1 << 1,	/* OBL_LAUNCH required */
} flags_t;

typedef struct stm32		stm32_t;
typedef struct stm32_cmd	stm32_cmd_t;
typedef struct stm32_dev	stm32_dev_t;

/*
 * Specify the length of reply for command GET
 * This is helpful for frame-oriented protocols, e.g. i2c, to avoid time
 * consuming try-fail-timeout-retry operation.
 * On byte-oriented protocols, i.e. UART, this information would be skipped
 * after read the first byte, so not needed.
 */
struct varlen_cmd {
	uint8_t version;
	uint8_t length;
};

struct stm32 {
	Stream	*stream;
	uint8_t     flags;
	struct varlen_cmd *cmd_get_reply;
	uint8_t			bl_version;
	uint8_t			version;
	uint8_t			option1, option2;
	uint16_t		pid;
	stm32_cmd_t		*cmd;
	const stm32_dev_t	*dev;
};

struct stm32_dev {
	uint16_t	id;
//	const char	*name;
	uint32_t	ram_start, ram_end;
	uint32_t	fl_start, fl_end;
	uint16_t	fl_pps; // pages per sector
	uint32_t	*fl_ps;  // page size
	uint32_t	opt_start, opt_end;
	uint32_t	mem_start, mem_end;
	uint32_t	flags;
};

stm32_t *stm32_init(Stream *stream, const uint8_t flags, const char init);
void stm32_close(stm32_t *stm);
stm32_err_t stm32_read_memory(const stm32_t *stm, uint32_t address,
			      uint8_t data[], unsigned int len);
stm32_err_t stm32_write_memory(const stm32_t *stm, uint32_t address,
			       const uint8_t data[], unsigned int len);
stm32_err_t stm32_wunprot_memory(const stm32_t *stm);
stm32_err_t stm32_wprot_memory(const stm32_t *stm);
stm32_err_t stm32_erase_memory(const stm32_t *stm, uint32_t spage,
			       uint32_t pages);
stm32_err_t stm32_go(const stm32_t *stm, uint32_t address);
stm32_err_t stm32_reset_device(const stm32_t *stm);
stm32_err_t stm32_readprot_memory(const stm32_t *stm);
stm32_err_t stm32_runprot_memory(const stm32_t *stm);
stm32_err_t stm32_crc_memory(const stm32_t *stm, uint32_t address,
			     uint32_t length, uint32_t *crc);
stm32_err_t stm32_crc_wrapper(const stm32_t *stm, uint32_t address,
			      uint32_t length, uint32_t *crc);
uint32_t stm32_sw_crc(uint32_t crc, uint8_t *buf, unsigned int len);

#endif