Tasmota/tasmota/tasmota_xsns_sensor/xsns_12_ads1115.ino

/*
  xsns_12_ads1115_ada.ino - ADS1115 A/D Converter support for Tasmota

  Copyright (C) 2021  Syssi, stefanbode

  This program is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  This program is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with this program.  If not, see <http://www.gnu.org/licenses/>.
*/

#ifdef USE_I2C
#ifdef USE_ADS1115
/*********************************************************************************************\
 * ADS1115 - 4 channel 16BIT A/D converter
 *
 * Required library: none but based on Adafruit Industries ADS1015 library
 *
 * I2C Address: 0x48, 0x49, 0x4A or 0x4B
 *
 * The ADC input range (or gain) can be changed via the following
 * defines, but be careful never to exceed VDD +0.3V max, or to
 * exceed the upper and lower limits if you adjust the input range!
 * Setting these values incorrectly may destroy your ADC!
 *                                                                 ADS1115
 *                                                                 -------
 * ADS1115_REG_CONFIG_PGA_6_144V  // 2/3x gain +/- 6.144V  1 bit = 0.1875mV (default)
 * ADS1115_REG_CONFIG_PGA_4_096V  // 1x gain   +/- 4.096V  1 bit = 0.125mV
 * ADS1115_REG_CONFIG_PGA_2_048V  // 2x gain   +/- 2.048V  1 bit = 0.0625mV
 * ADS1115_REG_CONFIG_PGA_1_024V  // 4x gain   +/- 1.024V  1 bit = 0.03125mV
 * ADS1115_REG_CONFIG_PGA_0_512V  // 8x gain   +/- 0.512V  1 bit = 0.015625mV
 * ADS1115_REG_CONFIG_PGA_0_256V  // 16x gain  +/- 0.256V  1 bit = 0.0078125mV
\*********************************************************************************************/

#define XSNS_12                         12
#define XI2C_13                         13        // See I2CDEVICES.md

#define ADS1115_ADDRESS_ADDR_GND        0x48      // address pin low (GND)
#define ADS1115_ADDRESS_ADDR_VDD        0x49      // address pin high (VCC)
#define ADS1115_ADDRESS_ADDR_SDA        0x4A      // address pin tied to SDA pin
#define ADS1115_ADDRESS_ADDR_SCL        0x4B      // address pin tied to SCL pin

#define ADS1115_CONVERSIONDELAY         (8)       // CONVERSION DELAY (in mS)

#define ADS1115_SINGLE_CHANNELS         (4)
#define ADS1115_DIFFERENTIAL_CHANNELS   (2)

/*======================================================================
POINTER REGISTER
-----------------------------------------------------------------------*/
#define ADS1115_REG_POINTER_MASK        (0x03)
#define ADS1115_REG_POINTER_CONVERT     (0x00)
#define ADS1115_REG_POINTER_CONFIG      (0x01)
#define ADS1115_REG_POINTER_LOWTHRESH   (0x02)
#define ADS1115_REG_POINTER_HITHRESH    (0x03)

/*======================================================================
CONFIG REGISTER
-----------------------------------------------------------------------*/
#define ADS1115_REG_CONFIG_OS_MASK      (0x8000)
#define ADS1115_REG_CONFIG_OS_SINGLE    (0x8000)  // Write: Set to start a single-conversion
#define ADS1115_REG_CONFIG_OS_BUSY      (0x0000)  // Read: Bit = 0 when conversion is in progress
#define ADS1115_REG_CONFIG_OS_NOTBUSY   (0x8000)  // Read: Bit = 1 when device is not performing a conversion

#define ADS1115_REG_CONFIG_MUX_MASK     (0x7000)
#define ADS1115_REG_CONFIG_MUX_DIFF_0_1 (0x0000)  // Differential P = AIN0, N = AIN1 (default)
#define ADS1115_REG_CONFIG_MUX_DIFF_0_3 (0x1000)  // Differential P = AIN0, N = AIN3
#define ADS1115_REG_CONFIG_MUX_DIFF_1_3 (0x2000)  // Differential P = AIN1, N = AIN3
#define ADS1115_REG_CONFIG_MUX_DIFF_2_3 (0x3000)  // Differential P = AIN2, N = AIN3
#define ADS1115_REG_CONFIG_MUX_SINGLE_0 (0x4000)  // Single-ended AIN0
#define ADS1115_REG_CONFIG_MUX_SINGLE_1 (0x5000)  // Single-ended AIN1
#define ADS1115_REG_CONFIG_MUX_SINGLE_2 (0x6000)  // Single-ended AIN2
#define ADS1115_REG_CONFIG_MUX_SINGLE_3 (0x7000)  // Single-ended AIN3

#define ADS1115_REG_CONFIG_PGA_MASK     (0x0E00)
#define ADS1115_REG_CONFIG_PGA_6_144V   (0x0000)  // +/-6.144V range = Gain 2/3 (default)
#define ADS1115_REG_CONFIG_PGA_4_096V   (0x0200)  // +/-4.096V range = Gain 1
#define ADS1115_REG_CONFIG_PGA_2_048V   (0x0400)  // +/-2.048V range = Gain 2
#define ADS1115_REG_CONFIG_PGA_1_024V   (0x0600)  // +/-1.024V range = Gain 4
#define ADS1115_REG_CONFIG_PGA_0_512V   (0x0800)  // +/-0.512V range = Gain 8
#define ADS1115_REG_CONFIG_PGA_0_256V   (0x0A00)  // +/-0.256V range = Gain 16

#define ADS1115_REG_CONFIG_MODE_MASK    (0x0100)
#define ADS1115_REG_CONFIG_MODE_CONTIN  (0x0000)  // Continuous conversion mode
#define ADS1115_REG_CONFIG_MODE_SINGLE  (0x0100)  // Power-down single-shot mode (default)

#define ADS1115_REG_CONFIG_DR_MASK      (0x00E0)
#define ADS1115_REG_CONFIG_DR_128SPS    (0x0000)  // 128 samples per second
#define ADS1115_REG_CONFIG_DR_250SPS    (0x0020)  // 250 samples per second
#define ADS1115_REG_CONFIG_DR_490SPS    (0x0040)  // 490 samples per second
#define ADS1115_REG_CONFIG_DR_920SPS    (0x0060)  // 920 samples per second
#define ADS1115_REG_CONFIG_DR_1600SPS   (0x0080)  // 1600 samples per second (default)
#define ADS1115_REG_CONFIG_DR_2400SPS   (0x00A0)  // 2400 samples per second
#define ADS1115_REG_CONFIG_DR_3300SPS   (0x00C0)  // 3300 samples per second
#define ADS1115_REG_CONFIG_DR_6000SPS   (0x00E0)  // 6000 samples per second

#define ADS1115_REG_CONFIG_CMODE_MASK   (0x0010)
#define ADS1115_REG_CONFIG_CMODE_TRAD   (0x0000)  // Traditional comparator with hysteresis (default)
#define ADS1115_REG_CONFIG_CMODE_WINDOW (0x0010)  // Window comparator

#define ADS1115_REG_CONFIG_CPOL_MASK    (0x0008)
#define ADS1115_REG_CONFIG_CPOL_ACTVLOW (0x0000)  // ALERT/RDY pin is low when active (default)
#define ADS1115_REG_CONFIG_CPOL_ACTVHI  (0x0008)  // ALERT/RDY pin is high when active

#define ADS1115_REG_CONFIG_CLAT_MASK    (0x0004)  // Determines if ALERT/RDY pin latches once asserted
#define ADS1115_REG_CONFIG_CLAT_NONLAT  (0x0000)  // Non-latching comparator (default)
#define ADS1115_REG_CONFIG_CLAT_LATCH   (0x0004)  // Latching comparator

#define ADS1115_REG_CONFIG_CQUE_MASK    (0x0003)
#define ADS1115_REG_CONFIG_CQUE_1CONV   (0x0000)  // Assert ALERT/RDY after one conversions
#define ADS1115_REG_CONFIG_CQUE_2CONV   (0x0001)  // Assert ALERT/RDY after two conversions
#define ADS1115_REG_CONFIG_CQUE_4CONV   (0x0002)  // Assert ALERT/RDY after four conversions
#define ADS1115_REG_CONFIG_CQUE_NONE    (0x0003)  // Disable the comparator and put ALERT/RDY in high state (default)

struct ADS1115 {
  uint8_t count = 0;
  uint8_t address;
  uint8_t addresses[4] = { ADS1115_ADDRESS_ADDR_GND, ADS1115_ADDRESS_ADDR_VDD, ADS1115_ADDRESS_ADDR_SDA, ADS1115_ADDRESS_ADDR_SCL };
  uint8_t channels;
  uint16_t range;
  uint8_t found[4] = {false,false,false,false};
  int16_t last_values[4][4] = {{0,0,0,0},{0,0,0,0},{0,0,0,0},{0,0,0,0}};
} Ads1115;

//Ads1115StartComparator(channel, ADS1115_REG_CONFIG_MODE_SINGLE);
//Ads1115StartComparator(channel, ADS1115_REG_CONFIG_MODE_CONTIN);
void Ads1115StartComparator(uint8_t channel, uint16_t mode)
{
  // Start with default values
  uint16_t config = mode |
                    ADS1115_REG_CONFIG_CQUE_NONE    | // Comparator enabled and asserts on 1 match
                    ADS1115_REG_CONFIG_CLAT_NONLAT  | // Non Latching mode
                     Ads1115.range                  | // ADC Input voltage range (Gain)
                    ADS1115_REG_CONFIG_CPOL_ACTVLOW | // Alert/Rdy active low   (default val)
                    ADS1115_REG_CONFIG_CMODE_TRAD   | // Traditional comparator (default val)
                    ADS1115_REG_CONFIG_DR_6000SPS;    // 6000 samples per second

  // Set single-ended or differential input channel
  if (Ads1115.channels == ADS1115_SINGLE_CHANNELS) {
    config |= (ADS1115_REG_CONFIG_MUX_SINGLE_0 + (0x1000 * channel));
  } else {
    config |= (ADS1115_REG_CONFIG_MUX_DIFF_0_1 + (0x3000 * channel));
  }

  // Write config register to the ADC
  I2cWrite16(Ads1115.address, ADS1115_REG_POINTER_CONFIG, config);
}

int16_t Ads1115GetConversion(uint8_t channel)
{
  Ads1115StartComparator(channel, ADS1115_REG_CONFIG_MODE_SINGLE);
  // Wait for the conversion to complete
  delay(ADS1115_CONVERSIONDELAY);
  // Read the conversion results
  I2cRead16(Ads1115.address, ADS1115_REG_POINTER_CONVERT);

  Ads1115StartComparator(channel, ADS1115_REG_CONFIG_MODE_CONTIN);
  delay(ADS1115_CONVERSIONDELAY);
  // Read the conversion results
  uint16_t res = I2cRead16(Ads1115.address, ADS1115_REG_POINTER_CONVERT);
  return (int16_t)res;
}

/********************************************************************************************/

void Ads1115Detect(void)
{
  // Set default mode and range
  Ads1115.channels = ADS1115_SINGLE_CHANNELS;
  Ads1115.range = ADS1115_REG_CONFIG_PGA_6_144V;

  for (uint32_t i = 0; i < sizeof(Ads1115.addresses); i++) {
    if (!Ads1115.found[i]) {
      Ads1115.address = Ads1115.addresses[i];
      if (!I2cSetDevice(Ads1115.address)) { continue; }
      uint16_t buffer;
      if (I2cValidRead16(&buffer, Ads1115.address, ADS1115_REG_POINTER_CONVERT) &&
          I2cValidRead16(&buffer, Ads1115.address, ADS1115_REG_POINTER_CONFIG)) {
        Ads1115StartComparator(i, ADS1115_REG_CONFIG_MODE_CONTIN);
        I2cSetActiveFound(Ads1115.address, "ADS1115");
        Ads1115.found[i] = 1;
        Ads1115.count++;
      }
    }
  }
}

// Create the identifier of the the selected sensor
void Ads1115Label(char* label, uint32_t maxsize, uint8_t address) {
  if (1 == Ads1115.count) {
    // "ADS1115":{"A0":3240,"A1":3235,"A2":3269,"A3":3269}
    snprintf_P(label, maxsize, PSTR("ADS1115"));
  } else {
    // "ADS1115-48":{"A0":3240,"A1":3235,"A2":3269,"A3":3269},"ADS1115-49":{"A0":3240,"A1":3235,"A2":3269,"A3":3269}
    snprintf_P(label, maxsize, PSTR("ADS1115%c%02x"), IndexSeparator(), address);
  }
}

#ifdef USE_RULES
// Check every 250ms if there are relevant changes in any of the analog inputs
// and if so then trigger a message
void AdsEvery250ms(void)
{
  int16_t value;

  for (uint32_t t = 0; t < sizeof(Ads1115.addresses); t++) {
    if (Ads1115.found[t]) {

      uint8_t old_address = Ads1115.address;
      Ads1115.address = Ads1115.addresses[t];

      // collect first wich addresses have changed. We can save on rule processing this way
      uint32_t changed = 0;
      for (uint32_t i = 0; i < Ads1115.channels; i++) {
        value = Ads1115GetConversion(i);

        // Check if value has changed more than 1 percent from last stored value
        // we assume that gain is set up correctly, and we could use the whole 16bit result space
        if (value >= Ads1115.last_values[t][i] + 327 || value <= Ads1115.last_values[t][i] - 327) {
          Ads1115.last_values[t][i] = value;
          bitSet(changed, i);
        }
      }
      Ads1115.address = old_address;
      if (changed) {
        char label[15];
        Ads1115Label(label, sizeof(label), Ads1115.addresses[t]);

        Response_P(PSTR("{\"%s\":{"), label);

        bool first = true;
        for (uint32_t i = 0; i < Ads1115.channels; i++) {
          if (bitRead(changed, i)) {
            ResponseAppend_P(PSTR("%s\"A%ddiv10\":%d"), (first) ? "" : ",", i, Ads1115.last_values[t][i]);
            first = false;
          }
        }
        ResponseJsonEndEnd();

        XdrvRulesProcess(0);
      }

    }
  }
}
#endif  // USE_RULES

void Ads1115Show(bool json)
{
  int16_t values[4];

  for (uint32_t t = 0; t < sizeof(Ads1115.addresses); t++) {
    //AddLog(LOG_LEVEL_INFO, "Logging ADS1115 %02x", Ads1115.addresses[t]);
    if (Ads1115.found[t]) {

      uint8_t old_address = Ads1115.address;
      Ads1115.address = Ads1115.addresses[t];
      for (uint32_t i = 0; i < Ads1115.channels; i++) {
        values[i] = Ads1115GetConversion(i);
        //AddLog(LOG_LEVEL_INFO, "Logging ADS1115 %02x (%i) = %i", Ads1115.address, i, values[i] );
      }
      Ads1115.address = old_address;

      char label[15];
      Ads1115Label(label, sizeof(label), Ads1115.addresses[t]);

      if (json) {
        ResponseAppend_P(PSTR(",\"%s\":{"), label);
        for (uint32_t i = 0; i < Ads1115.channels; i++) {
          ResponseAppend_P(PSTR("%s\"A%d\":%d"), (0 == i) ? "" : ",", i, values[i]);
        }
        ResponseJsonEnd();
      }
#ifdef USE_WEBSERVER
      else {
        for (uint32_t i = 0; i < Ads1115.channels; i++) {
          WSContentSend_PD(HTTP_SNS_ANALOG, label, i, values[i]);
        }
      }
#endif  // USE_WEBSERVER
    }
  }
}

bool ADS1115_Command(void)
{
  const char ds[2][13] = {"Differential","Single ended"};
  const uint16_t r[6] = {6144,4096,2048,1024,512,256};
  if (XdrvMailbox.data_len > 1) {
    UpperCase(XdrvMailbox.data,XdrvMailbox.data);
    switch (XdrvMailbox.data[0]) {
      case 'D':
        Ads1115.channels = ADS1115_DIFFERENTIAL_CHANNELS;
        break;
      case 'S':
        Ads1115.channels = ADS1115_SINGLE_CHANNELS;
    }
    switch (XdrvMailbox.data[1]) {
      case '0':
        Ads1115.range = ADS1115_REG_CONFIG_PGA_6_144V;
        break;
      case '1':
        Ads1115.range = ADS1115_REG_CONFIG_PGA_4_096V;
        break;
      case '2':
        Ads1115.range = ADS1115_REG_CONFIG_PGA_2_048V;
        break;
      case '3':
        Ads1115.range = ADS1115_REG_CONFIG_PGA_1_024V;
        break;
      case '4':
        Ads1115.range = ADS1115_REG_CONFIG_PGA_0_512V;
        break;
      case '5':
        Ads1115.range = ADS1115_REG_CONFIG_PGA_0_256V;
    }
  }
 Response_P("{\"ADS1115\":{\"Settings\":\"%c%u\",\"Mode\":\"%s\",\"Range\":%u,\"Unit\":\"mV\"}}",ds[(Ads1115.channels>>1)-1][0],Ads1115.range>>9,ds[(Ads1115.channels>>1)-1],r[Ads1115.range>>9]);
  return true;
}

/*********************************************************************************************\
 * Interface
\*********************************************************************************************/

bool Xsns12(uint32_t function)
{
  if (!I2cEnabled(XI2C_13)) { return false; }

  bool result = false;

  if (FUNC_INIT == function) {
    Ads1115Detect();
  }
  else if (Ads1115.count) {
    switch (function) {
#ifdef USE_RULES
      case FUNC_EVERY_250_MSECOND:
        AdsEvery250ms();
        break;
#endif  // USE_RULES
      case FUNC_JSON_APPEND:
        Ads1115Show(1);
        break;
#ifdef USE_WEBSERVER
      case FUNC_WEB_SENSOR:
        Ads1115Show(0);
        break;
#endif  // USE_WEBSERVER
      case FUNC_COMMAND_SENSOR:
        if (XSNS_12 == XdrvMailbox.index) {
          result = ADS1115_Command();
        }
        break;
    }
  }
  return result;
}

#endif  // USE_ADS1115
#endif  // USE_I2C