Tasmota/lib/esp-knx-ip-0.5.1/examples/static-config/static-config.ino

/*
 * This is an example showing a simple environment sensor based on a BME280 attached via I2C.
 * It shows, how the library can used to statically configure a device without a webserver for config.
 * This sketch was tested on a WeMos D1 mini
 */

#include <Adafruit_BME280.h>
#include <esp-knx-ip.h>

// WiFi config here
const char* ssid = "myssid";
const char* pass = "mypassword";

#define LED_PIN D4
#define UPDATE_INTERVAL 10000

unsigned long next_change = 0;

float last_temp = 0.0;
float last_hum = 0.0;
float last_pres = 0.0;

Adafruit_BME280 bme;

// Group addresses to send to (1/1/1, 1/1/2 and 1/1/3)
address_t temp_ga = knx.GA_to_address(1, 1, 1);
address_t hum_ga = knx.GA_to_address(1, 1, 2);
address_t pres_ga = knx.GA_to_address(1, 1, 3);

void setup() {
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(115200);

  callback_id_t temp_cb = knx.callback_register("Read Temperature", temp_cb);
  callback_id_t hum_cb =knx.callback_register("Read Humidity", hum_cb);
  callback_id_t pres_cb =knx.callback_register("Read Pressure", pres_cb);

  // Assign callbacks to group addresses (2/1/1, 2/1/2, 2/1/3)
  knx.callback_assign(temp_cb, knx.GA_to_address(2, 1, 1));
  knx.callback_assign(hum_cb, knx.GA_to_address(2, 1, 2));
  knx.callback_assign(pres_cb, knx.GA_to_address(2, 1, 3));

  // Set physical address (1.1.1)
  knx.physical_address_set(knx.PA_to_address(1, 1, 1));

  // Do not call knx.load() for static config, it will try to load config from EEPROM which we don't have here

  // Init sensor
  if (!bme.begin(0x76)) {  
    Serial.println("Could not find a valid BME280 sensor, check wiring!");
  }

  // Init WiFi
  WiFi.hostname("env");
  WiFi.begin(ssid, pass);

  Serial.println("");
  Serial.print("[Connecting]");
  Serial.print(ssid);

  digitalWrite(LED_PIN, LOW);
  while (WiFi.status() != WL_CONNECTED) {
    digitalWrite(LED_PIN, HIGH);
    delay(250);
    Serial.print(".");
    digitalWrite(LED_PIN, LOW);
    delay(250);
  }
  digitalWrite(LED_PIN, HIGH);

  // Start knx, disable webserver by passing nullptr
  knx.start(nullptr);

  Serial.println();
  Serial.println("Connected to wifi");
  Serial.println(WiFi.localIP());
}

void loop() {
  knx.loop();
  
  unsigned long now = millis();

  if (next_change < now)
  {
    next_change = now + UPDATE_INTERVAL;

    last_temp = bme.readTemperature();
    last_hum = bme.readHumidity();
    last_pres = bme.readPressure()/100.0f;

    Serial.print("T: ");
    Serial.print(last_temp);
    Serial.print("°C H: ");
    Serial.print(last_hum);
    Serial.print("% P: ");
    Serial.print(last_pres);
    Serial.println("hPa");

    knx.write_2byte_float(temp_ga, last_temp);
    knx.write_2byte_float(hum_ga, last_hum);
    knx.write_2byte_float(pres_ga, last_pres);
  }

  delay(50);
}

void temp_cb(message_t const &msg, void *arg)
{
  switch (msg.ct)
  {
    case KNX_CT_READ:
    {
      knx.answer_2byte_float(msg.received_on, last_temp);
      break;
    }
  }
}

void hum_cb(message_t const &msg, void *arg)
{
  switch (msg.ct)
  {
    case KNX_CT_READ:
    {
      knx.answer_2byte_float(msg.received_on, last_hum);
      break;
    }
  }
}

void pres_cb(message_t const &msg, void *arg)
{
  switch (msg.ct)
  {
    case KNX_CT_READ:
    {
      knx.answer_2byte_float(msg.received_on, last_pres);
      break;
    }
  }
}