Tasmota/tasmota/tasmota_xdrv_driver/xdrv_49_pid.ino

/*
  xdrv_49_pid.ino - PID algorithm plugin for Sonoff-Tasmota

  Copyright (C) 2021  Colin Law and Thomas Herrmann

  This program is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  This program is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with this program.  If not, see <http://www.gnu.org/licenses/>.
*/

#ifdef USE_PID
#ifndef FIRMWARE_MINIMAL
/*********************************************************************************************\
 * Uses the library https://github.com/colinl/process-control.git from Github
 * In user_config_override.h include code as follows:

 #define USE_PID         // include the pid feature (+4.3k)
   #define PID_SETPOINT                  19.5    // Setpoint value. This is the process value that the process is
                                                 // aiming for.
                                                 // May be adjusted via MQTT using cmnd PidSp

   #define PID_PROPBAND                  5       // Proportional band in process units (eg degrees). This controls
                                                 // the gain of the loop and is the range of process value over which
                                                 // the power output will go from 0 to full power. The units are that
                                                 // of the process and setpoint, so for example in a heating
                                                 // application it might be set to 1.5 degrees.
                                                 // May be adjusted via MQTT using cmnd PidPb

   #define PID_INTEGRAL_TIME             1800    // Integral time seconds. This is a setting for the integral time,
                                                 // in seconds. It represents the time constant of the integration
                                                 // effect. The larger the value the slower the integral effect will be.
                                                 // Obviously the slower the process is the larger this should be. For
                                                 // example for a domestic room heated by convection radiators a setting
                                                 // of one hour might be appropriate (in seconds). To disable the
                                                 // integral effect set this to a large number.
                                                 // May be adjusted via MQTT using cmnd PidTi

   #define PID_DERIVATIVE_TIME           15      // Derivative time seconds. This is a setting for the derivative time,
                                                 // in seconds. It represents the time constant of the derivative effect.
                                                 // The larger the value the greater will be the derivative effect.
                                                 // Typically this will be set to somewhat less than 25% of the integral
                                                 // setting, once the integral has been adjusted to the optimum value. To
                                                 // disable the derivative effect set this to 0. When initially tuning a
                                                 // loop it is often sensible to start with derivative zero and wind it in
                                                 // once other parameters have been setup.
                                                 // May be adjusted via MQTT using cmnd PidTd

   #define PID_INITIAL_INT               0.5     // Initial integral value (0:1). This is an initial value which is used
                                                 // to preset the integrated error value when the flow is deployed in
                                                 // order to assist in homing in on the setpoint the first time. It should
                                                 // be set to an estimate of what the power requirement might be in order
                                                 // to maintain the process at the setpoint. For example for a domestic
                                                 // room heating application it might be set to 0.2 indicating that 20% of
                                                 // the available power might be required to maintain the setpoint. The
                                                 // value is of no consequence apart from device restart.

   #define PID_MAX_INTERVAL              300     // This is the maximum time in seconds that is expected between samples.
                                                 // It is provided to cope with unusual situations such as a faulty sensor
                                                 // that might prevent the node from being supplied with a process value.
                                                 // If no new process value is received for this time then the power is set
                                                 // to the value defined for PID_MANUAL_POWER.
                                                 // May be adjusted via MQTT using cmnd PidMaxInterval

   #define PID_DERIV_SMOOTH_FACTOR       3       // In situations where the process sensor has limited resolution (such as
                                                 // the DS18B20), the use of deriviative can be problematic as when the
                                                 // process is changing only slowly the steps in the value cause spikes in
                                                 // the derivative. To reduce the effect of these this parameter can be
                                                 // set to apply a filter to the derivative term. I have found that with
                                                 // the DS18B20 that a value of 3 here can be beneficial, providing
                                                 // effectively a low pass filter on the derivative at 1/3 of the derivative
                                                 // time. This feature may also be useful if the process value is particularly
                                                 // noisy. The smaller the value the greater the filtering effect but the
                                                 // more it will reduce the effectiveness of the derivative. A value of zero
                                                 // disables this feature.
                                                 // May be adjusted via MQTT using cmnd PidDSmooth

   #define PID_AUTO                      1       // Auto mode 1 or 0 (for manual). This can be used to enable or disable
                                                 // the control (1=enable, auto mode, 0=disabled, manual mode). When in
                                                 // manual mode the output is set the value definded for PID_MANUAL_POWER
                                                 // May be adjusted via MQTT using cmnd PidAuto

   #define PID_MANUAL_POWER              0       // Power output when in manual mode or fallback mode if too long elapses
                                                 // between process values
                                                 // May be adjusted via MQTT using cmnd PidManualPower

   #define PID_UPDATE_SECS               0       // How often to run the pid algorithm (integer secs) or 0 to run the algorithm
                                                 // each time a new pv value is received, for most applictions specify 0.
                                                 // Otherwise set this to a time
                                                 // that is short compared to the response of the process.  For example,
                                                 // something like 15 seconds may well be appropriate for a domestic room
                                                 // heating application.
                                                 // May be adjusted via MQTT using cmnd PidUpdateSecs

   #define PID_USE_TIMPROP               1       // To use an internal relay for a time proportioned output to drive the
                                                 // process, set this to indicate which timeprop output to use. For a device
                                                 // with just one relay then this will be 1.
                                                 // USE_TIMEPROP will be automativally included. You must set the output as
                                                 // explained in xdrv_48_timeprop.ino
                                                 // To disable, override to false in user_config_override.h. If USE_TIMEPROP is
                                                 // not explicitly defined, then it will not be added by default.

   #define PID_USE_LOCAL_SENSOR                  // If defined then the local sensor will be used for pv. Leave undefined if
                                                 // this is not required.  The rate that the sensor is read is defined by TELE_PERIOD
                                                 // If not using the sensor then you can supply process values via MQTT using
                                                 // cmnd PidPv

    #define PID_LOCAL_SENSOR_NAME         "DS18B20"           // local sensor name when PID_USE_LOCAL_SENSOR is defined above
                                                              // the JSON payload is parsed for this sensor to find the present value
                                                              // eg "ESP32":{"Temperature":31.4},"DS18B20":{"Temperature":12.6}

    #define PID_LOCAL_SENSOR_TYPE         D_JSON_TEMPERATURE  // Choose one of D_JSON_TEMPERATURE D_JSON_HUMIDITY D_JSON_PRESSURE
                                                              // or any string as the sensor type. The JSON payload is parsed for the
                                                              // value in this field
                                                              // eg "HDC1080":{"Temperature":24.8,"Humidity":79.2}

   #define PID_SHUTTER                   1       // if using the PID to control a 3-way valve, create Tasmota Shutter and define the
                                                 // number of the shutter here. Otherwise leave this commented out

   #define PID_REPORT_MORE_SETTINGS    true      // If defined to true, the SENSOR output will provide more extensive json
                                                 // output in the PID section. Override to false to reduce json output

 * Help with using the PID algorithm and with loop tuning can be found at
 * http://blog.clanlaw.org.uk/2018/01/09/PID-tuning-with-node-red-contrib-pid.html
 * This is directed towards using the algorithm in the node-red node node-red-contrib-pid but the algorithm here is based on
 * the code there and the tuning technique described there should work just the same.
\*********************************************************************************************/

#ifndef PID_SETPOINT
#define PID_SETPOINT                  19.5    // [PidSp] Setpoint value.
#endif
#ifndef PID_PROPBAND
#define PID_PROPBAND                  5       // [PidPb] Proportional band in process units (eg degrees).
#endif
#ifndef PID_INTEGRAL_TIME
#define PID_INTEGRAL_TIME             1800    // [PidTi] Integral time seconds.
#endif
#ifndef PID_DERIVATIVE_TIME
#define PID_DERIVATIVE_TIME           15      // [PidTd] Derivative time seconds.
#endif
#ifndef PID_INITIAL_INT
#define PID_INITIAL_INT               0.5     // Initial integral value (0:1).
#endif
#ifndef PID_MAX_INTERVAL
#define PID_MAX_INTERVAL              300     // [PidMaxInterval] This is the maximum time in seconds between samples.
#endif
#ifndef PID_DERIV_SMOOTH_FACTOR
#define PID_DERIV_SMOOTH_FACTOR       3       // [PidDSmooth]
#endif
#ifndef PID_AUTO
#define PID_AUTO                      1       // [PidAuto] Auto mode 1 or 0 (for manual).
#endif
#ifndef PID_MANUAL_POWER
#define PID_MANUAL_POWER              0       // [PidManualPower] Power output when in manual mode or fallback mode.
#endif
#ifndef PID_UPDATE_SECS
#define PID_UPDATE_SECS               0       // [PidUpdateSecs] How often to run the pid algorithm
#endif

#ifndef PID_USE_TIMPROP
#define PID_USE_TIMPROP               1       // To disable this feature define as false in user_config_override
#endif

// #define PID_USE_LOCAL_SENSOR                 // If defined then the local sensor will be used for pv.
#ifndef PID_LOCAL_SENSOR_NAME
#define PID_LOCAL_SENSOR_NAME         "DS18B20" // local sensor name when PID_USE_LOCAL_SENSOR is defined
#endif
#ifndef PID_LOCAL_SENSOR_TYPE
#define PID_LOCAL_SENSOR_TYPE         D_JSON_TEMPERATURE // local sensor type
#endif

//#define PID_SHUTTER                   1       // Number of the shutter here. Otherwise leave this commented out
#ifndef PID_REPORT_MORE_SETTINGS
#define PID_REPORT_MORE_SETTINGS     true     // Override to false if less details are required in SENSOR JSON
#endif

#include "PID.h"

/* This might need to go to i18n.h */
#define D_PRFX_PID "Pid"
#define D_CMND_PID_SETPV "Pv"
#define D_CMND_PID_SETSETPOINT "Sp"
#define D_CMND_PID_SETPROPBAND "Pb"
#define D_CMND_PID_SETINTEGRAL_TIME "Ti"
#define D_CMND_PID_SETDERIVATIVE_TIME "Td"
#define D_CMND_PID_SETINITIAL_INT "Initint"
#define D_CMND_PID_SETDERIV_SMOOTH_FACTOR "DSmooth"
#define D_CMND_PID_SETAUTO "Auto"
#define D_CMND_PID_SETMANUAL_POWER "ManualPower"
#define D_CMND_PID_SETMAX_INTERVAL "MaxInterval"
#define D_CMND_PID_SETUPDATE_SECS "UpdateSecs"
#define D_CMND_PID_SETSHUTDOWN "Shutdown"

const char kPIDCommands[] PROGMEM = D_PRFX_PID "|" // Prefix
  D_CMND_PID_SETPV "|"
  D_CMND_PID_SETSETPOINT "|"
  D_CMND_PID_SETPROPBAND "|"
  D_CMND_PID_SETINTEGRAL_TIME "|"
  D_CMND_PID_SETDERIVATIVE_TIME "|"
  D_CMND_PID_SETINITIAL_INT "|"
  D_CMND_PID_SETDERIV_SMOOTH_FACTOR "|"
  D_CMND_PID_SETAUTO "|"
  D_CMND_PID_SETMANUAL_POWER "|"
  D_CMND_PID_SETMAX_INTERVAL "|"
  D_CMND_PID_SETUPDATE_SECS "|"
  D_CMND_PID_SETSHUTDOWN;
  ;

void (* const PIDCommand[])(void) PROGMEM = {
  &CmndSetPv,
  &CmndSetSp,
  &CmndSetPb,
  &CmndSetTi,
  &CmndSetTd,
  &CmndSetInitialInt,
  &CmndSetDSmooth,
  &CmndSetAuto,
  &CmndSetManualPower,
  &CmndSetMaxInterval,
  &CmndSetUpdateSecs,
  &CmndSetShutdown
  };

struct {
  PID pid;
  int update_secs = PID_UPDATE_SECS <= 0  ?  0  :  PID_UPDATE_SECS;   // how often (secs) the pid alogorithm is run
  int max_interval = PID_MAX_INTERVAL;
  unsigned long last_pv_update_secs = 0;
  bool run_pid_now = false;     // tells PID_Every_Second to run the pid algorithm
  long current_time_secs = 0;  // a counter that counts seconds since initialisation
  bool shutdown = false;        // power commands will be ignored when true
} Pid;

void PIDInit()
{
  Pid.pid.initialise( PID_SETPOINT, PID_PROPBAND, PID_INTEGRAL_TIME, PID_DERIVATIVE_TIME, PID_INITIAL_INT,
    PID_MAX_INTERVAL, PID_DERIV_SMOOTH_FACTOR, PID_AUTO, PID_MANUAL_POWER );
}

void PIDEverySecond() {
  static int sec_counter = 0;
  Pid.current_time_secs++;    // increment time
  // run the pid algorithm if Pid.run_pid_now is true or if the right number of seconds has passed or if too long has
  // elapsed since last pv update. If too long has elapsed the the algorithm will deal with that.
  if (Pid.run_pid_now  ||  Pid.current_time_secs - Pid.last_pv_update_secs > Pid.max_interval  ||  (Pid.update_secs != 0 && sec_counter++ % Pid.update_secs  ==  0)) {
    if (!Pid.run_pid_now) {
      PIDShowSensor();    // set actual process value
    }
    PIDRun();
    Pid.run_pid_now = false;
  }
}

void PIDShowSensor() {
  // Called each time new sensor data available, data in mqtt data in same format
  // as published in tele/SENSOR
  // Update period is specified in TELE_PERIOD

  float sensor_reading = NAN;

#if defined PID_USE_LOCAL_SENSOR
  // copy the string into a new buffer that will be modified and
  // parsed to find the local sensor reading if it's there
  String buf = ResponseData();
  JsonParser parser((char*)buf.c_str());
  JsonParserObject root = parser.getRootObject();
  if (root) {
    JsonParserToken value_token = root[PID_LOCAL_SENSOR_NAME].getObject()[PSTR(PID_LOCAL_SENSOR_TYPE)];
    if (value_token.isNum()) {
      sensor_reading = value_token.getFloat();
    }
  }
#endif // PID_USE_LOCAL_SENSOR

  if (!isnan(sensor_reading)) {

    // pass the value to the pid alogorithm to use as current pv
    Pid.last_pv_update_secs = Pid.current_time_secs;
    Pid.pid.setPv(sensor_reading, Pid.last_pv_update_secs);
    // also trigger running the pid algorithm if we have been told to run it each pv sample
    if (Pid.update_secs == 0) {
      // this runs it at the next second
      Pid.run_pid_now = true;
    }
  } else {
    // limit sensor not seen message to every 60 seconds to avoid flooding the logs
    if ((Pid.current_time_secs - Pid.last_pv_update_secs) > Pid.max_interval && ((Pid.current_time_secs - Pid.last_pv_update_secs)%60)==0) {
      AddLog(LOG_LEVEL_ERROR, PSTR("PID: Local temperature sensor missing for longer than PID_MAX_INTERVAL"));
    }
  }
}

void CmndSetPv(void) {
  Pid.last_pv_update_secs = Pid.current_time_secs;
  if (XdrvMailbox.data_len > 0) {
    Pid.pid.setPv(CharToFloat(XdrvMailbox.data), Pid.last_pv_update_secs);
  }
  // also trigger running the pid algorithm if we have been told to run it each pv sample
  if (Pid.update_secs == 0) {
    // this runs it at the next second
    Pid.run_pid_now = true;
  }
  ResponseCmndFloat(Pid.pid.getPv(), 1);
}

void CmndSetSp(void) {
  if (XdrvMailbox.data_len > 0) {
    Pid.pid.setSp(CharToFloat(XdrvMailbox.data));
  }
  ResponseCmndFloat(Pid.pid.getSp(), 1);
}

void CmndSetPb(void) {
  if (XdrvMailbox.data_len > 0) {
    Pid.pid.setPb(CharToFloat(XdrvMailbox.data));
  }
  ResponseCmndFloat(Pid.pid.getPb(), 1);
}

void CmndSetTi(void) {
  if (XdrvMailbox.data_len > 0) {
    Pid.pid.setTi(CharToFloat(XdrvMailbox.data));
  }
  ResponseCmndFloat(Pid.pid.getTi(), 1);
}

void CmndSetTd(void) {
  if (XdrvMailbox.data_len > 0) {
    Pid.pid.setTd(CharToFloat(XdrvMailbox.data));
  }
  ResponseCmndFloat(Pid.pid.getTd(), 1);
}

void CmndSetInitialInt(void) {
  if (XdrvMailbox.data_len > 0) {
    Pid.pid.setInitialInt(CharToFloat(XdrvMailbox.data));
  }
  ResponseCmndNumber(Pid.pid.getInitialInt());
}

void CmndSetDSmooth(void) {
  if (XdrvMailbox.data_len > 0) {
    Pid.pid.setDSmooth(CharToFloat(XdrvMailbox.data));
  }
  ResponseCmndFloat(Pid.pid.getDSmooth(), 1);
}

void CmndSetAuto(void) {
  if (XdrvMailbox.payload >= 0) {
    if(!Pid.shutdown) {
      Pid.pid.setAuto(XdrvMailbox.payload);
    }
  }
  ResponseCmndNumber(Pid.pid.getAuto());
}

void CmndSetManualPower(void) {
  if (XdrvMailbox.data_len > 0) {
    if(!Pid.shutdown) {
      Pid.pid.setManualPower(CharToFloat(XdrvMailbox.data));
    }
  }
  ResponseCmndFloat(Pid.pid.getManualPower(), 2);
}

void CmndSetMaxInterval(void) {
  if (XdrvMailbox.payload >= 0) {
    Pid.pid.setMaxInterval(XdrvMailbox.payload);
    Pid.max_interval=XdrvMailbox.payload;
  }
  ResponseCmndNumber(Pid.pid.getMaxInterval());
}

void CmndSetUpdateSecs(void) {
  if (XdrvMailbox.payload >= 0) {
    Pid.update_secs = (XdrvMailbox.payload);
  }
  if (Pid.update_secs < 0) {
    Pid.update_secs = 0;
  }
  ResponseCmndNumber(Pid.update_secs);
}

void CmndSetShutdown(void) {
  if (XdrvMailbox.payload >= 0) {
    AddLog(LOG_LEVEL_INFO, PSTR("PID: Shutdown mode %s"), XdrvMailbox.payload>0 ? "activated" : "cleared");
    Pid.shutdown = (XdrvMailbox.payload>0);
    if(Pid.shutdown) {
      Pid.pid.setAuto(0);
      Pid.pid.setManualPower(0.0);
    }
  }
  ResponseCmndNumber(Pid.shutdown);
}

void PIDShowValues(void) {
  char str_buf[FLOATSZ];
  char chr_buf;
  int i_buf;
  double d_buf;
  ResponseAppend_P(PSTR(",\"PID\":{"));

  d_buf = Pid.pid.getPv();
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidPv\":%s,"), str_buf);
  d_buf = Pid.pid.getSp();
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidSp\":%s,"), str_buf);
  ResponseAppend_P(PSTR("\"PidShutdown\":%d,"), Pid.shutdown);

#if PID_REPORT_MORE_SETTINGS
  d_buf = Pid.pid.getPb();
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidPb\":%s,"), str_buf);
  d_buf = Pid.pid.getTi();
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidTi\":%s,"), str_buf);
  d_buf = Pid.pid.getTd();
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidTd\":%s,"), str_buf);
  d_buf = Pid.pid.getInitialInt();
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidInitialInt\":%s,"), str_buf);
  d_buf = Pid.pid.getDSmooth();
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidDSmooth\":%s,"), str_buf);
  chr_buf = Pid.pid.getAuto();
  ResponseAppend_P(PSTR("\"PidAuto\":%d,"), chr_buf);
  d_buf = Pid.pid.getManualPower();
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidManualPower\":%s,"), str_buf);
  i_buf = Pid.pid.getMaxInterval();
  ResponseAppend_P(PSTR("\"PidMaxInterval\":%d,"), i_buf);
  i_buf = Pid.current_time_secs - Pid.last_pv_update_secs;
  ResponseAppend_P(PSTR("\"PidInterval\":%d,"), i_buf);
  ResponseAppend_P(PSTR("\"PidUpdateSecs\":%d,"), Pid.update_secs);
#endif // PID_REPORT_MORE_SETTINGS

  i_buf = (Pid.current_time_secs - Pid.last_pv_update_secs) > Pid.pid.getMaxInterval();
  ResponseAppend_P(PSTR("\"PidSensorLost\":%d,"), i_buf);
// The actual power value
  d_buf = Pid.pid.tick(Pid.current_time_secs);
  dtostrfd(d_buf, 2, str_buf);
  ResponseAppend_P(PSTR("\"PidPower\":%s"), str_buf);

  ResponseAppend_P(PSTR("}"));
}

#ifdef USE_WEBSERVER
void PIDShowValuesWeb(void) {

#define D_PID_DISPLAY_NAME     "PID Controller"
#define D_PID_SET_POINT        "Set Point"
#define D_PID_PRESENT_VALUE    "Current Value"
#define D_PID_POWER            "Power"
#define D_PID_MODE             "Controller Mode"
#define D_PID_MODE_AUTO        "Auto"
#define D_PID_MODE_MANUAL      "Manual"
#define D_PID_MODE_OFF         "Off"

  const char HTTP_PID_HL[] PROGMEM = "{s}<hr>{m}<hr>{e}";
  const char HTTP_PID_INFO[] PROGMEM = "{s}" D_PID_DISPLAY_NAME "{m}%s{e}";
  const char HTTP_PID_SP_FORMAT[] PROGMEM = "{s}%s " "{m}%*_f ";
  const char HTTP_PID_PV_FORMAT[] PROGMEM = "{s}%s " "{m}%*_f ";
  const char HTTP_PID_POWER_FORMAT[] PROGMEM = "{s}%s " "{m}%*_f " D_UNIT_PERCENT;

  float f_buf;

  WSContentSend_P(HTTP_PID_HL);
  WSContentSend_P(HTTP_PID_INFO, (Pid.pid.getAuto()==1) ? D_PID_MODE_AUTO : Pid.pid.tick(Pid.current_time_secs)>0.0f ? D_PID_MODE_MANUAL : D_PID_MODE_OFF);

  if (Pid.pid.getAuto()==1 || Pid.pid.tick(Pid.current_time_secs)>0.0f) {
    f_buf = (float)Pid.pid.getSp();
    WSContentSend_PD(HTTP_PID_SP_FORMAT, D_PID_SET_POINT, 1, &f_buf);
    f_buf = (float)Pid.pid.getPv();
    WSContentSend_PD(HTTP_PID_PV_FORMAT, D_PID_PRESENT_VALUE, 1, &f_buf);
    f_buf = Pid.pid.tick(Pid.current_time_secs)*100.0f;
    WSContentSend_PD(HTTP_PID_POWER_FORMAT, D_PID_POWER, 0, &f_buf);
  }
}
#endif  // USE_WEBSERVER

void PIDRun(void) {
  double power = Pid.pid.tick(Pid.current_time_secs);
#ifdef PID_DONT_USE_PID_TOPIC
  // This part is left inside to regularly publish the PID Power via
  // `%topic%/PID {"power":"0.000"}`
  char str_buf[FLOATSZ];
  dtostrfd(power, 3, str_buf);
  Response_P(PSTR("{\"%s\":\"%s\"}"), "power", str_buf);
  MqttPublishPrefixTopicRulesProcess_P(TELE, "PID");
#endif // PID_DONT_USE_PID_TOPIC

#if defined PID_SHUTTER
  // send output as a position from 0-100 to defined shutter
  int pos = power * 100;
  ShutterSetPosition(PID_SHUTTER, pos);
#endif //PID_SHUTTER

#if defined(PID_USE_TIMPROP) && (PID_USE_TIMPROP > 0)
  // send power to appropriate timeprop output
  TimepropSetPower( PID_USE_TIMPROP-1, power );
#endif // PID_USE_TIMPROP
}

/*********************************************************************************************\
 * Interface
\*********************************************************************************************/

#define XDRV_49       49

bool Xdrv49(uint32_t function) {
  bool result = false;

  switch (function) {
    case FUNC_INIT:
      PIDInit();
      break;
    case FUNC_EVERY_SECOND:
      PIDEverySecond();
      break;
    case FUNC_SHOW_SENSOR:
      // only use this if the pid loop is to use the local sensor for pv
      #if defined PID_USE_LOCAL_SENSOR
        PIDShowSensor();
      #endif // PID_USE_LOCAL_SENSOR
      break;
    case FUNC_COMMAND:
      result = DecodeCommand(kPIDCommands, PIDCommand);
      break;
    case FUNC_JSON_APPEND:
      PIDShowValues();
      break;
#ifdef USE_WEBSERVER
    case FUNC_WEB_SENSOR:
      PIDShowValuesWeb();
      break;
#endif  // USE_WEBSERVER
  }
  return result;
}
#endif //FIRMWARE_MINIMAL
#endif // USE_PID