Tasmota/tasmota/xdrv_36_keeloq.ino

/*
  xdrv_36_keeloq.ino - Jarolift Keeloq shutter support for Tasmota

  Copyright (C) 2020  he-so

  This program is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  This program is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with this program.  If not, see <http://www.gnu.org/licenses/>.
*/

#ifdef USE_KEELOQ
/*********************************************************************************************\
 * Keeloq shutter support
 *
 * Uses hardware SPI and two user configurable GPIO's (CC1101 GDO0 and CC1101 GDO2)
 *
 * Considering the implementation these two user GPIO's are fake.
 * Only CC1101 GDO0 is used and must always be GPIO05 dictated by the used CC1101 library.
\*********************************************************************************************/

#define XDRV_36 36

#include "cc1101.h"
#include <KeeloqLib.h>

#define SYNC_WORD 199

#define Lowpulse         400
#define Highpulse        800

const char kJaroliftCommands[] PROGMEM = "Keeloq|" // prefix
  "SendRaw|SendButton|Set";

void (* const jaroliftCommand[])(void) PROGMEM = {
  &CmndSendRaw, &CmdSendButton, &CmdSet};

CC1101 cc1101;

struct JAROLIFT_DEVICE {
  int device_key_msb       = 0x0; // stores cryptkey MSB
  int device_key_lsb       = 0x0; // stores cryptkey LSB
  uint64_t button          = 0x0; // 1000=0x8 up, 0100=0x4 stop, 0010=0x2 down, 0001=0x1 learning
  int disc                 = 0x0100; // 0x0100 for single channel remote
  uint32_t enc             = 0x0;   // stores the 32Bit encrypted code
  uint64_t pack            = 0;   // Contains data to send.
  int count                = 0;
  uint32_t serial          = 0x0;
  uint8_t port_tx;
  uint8_t port_rx;
} jaroliftDevice;

void CmdSet(void)
{
  if (XdrvMailbox.data_len > 0) {
    if (XdrvMailbox.payload > 0) {
      char *p;
      uint32_t i = 0;
      uint32_t param[4] = { 0 };
      for (char *str = strtok_r(XdrvMailbox.data, ", ", &p); str && i < 4; str = strtok_r(nullptr, ", ", &p)) {
        param[i] = strtoul(str, nullptr, 0);
        i++;
      }
      for (uint32_t i = 0; i < 3; i++) {
        if (param[i] < 1) { param[i] = 1; }  // msb, lsb, serial, counter
      }
      DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("params: %08x %08x %08x %08x"), param[0], param[1], param[2], param[3]);
      Settings.keeloq_master_msb = param[0];
      Settings.keeloq_master_lsb = param[1];
      Settings.keeloq_serial = param[2];
      Settings.keeloq_count = param[3];

      jaroliftDevice.serial = param[2];
      jaroliftDevice.count = param[3];

      GenerateDeviceCryptKey();
      ResponseCmndDone();
    } else {
      DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("no payload"));
    }
  } else {
    DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("no param"));
  }
}

void GenerateDeviceCryptKey()
{
  Keeloq k(Settings.keeloq_master_msb, Settings.keeloq_master_lsb);
  jaroliftDevice.device_key_msb = k.decrypt(jaroliftDevice.serial | 0x60000000L);
  jaroliftDevice.device_key_lsb = k.decrypt(jaroliftDevice.serial | 0x20000000L);

  AddLog_P2(LOG_LEVEL_DEBUG, PSTR("generated device keys: %08x %08x"), jaroliftDevice.device_key_msb, jaroliftDevice.device_key_lsb);
}

void CmdSendButton(void)
{
  noInterrupts();
  entertx();

  if (XdrvMailbox.data_len > 0)
  {
    if (XdrvMailbox.payload > 0)
    {
      jaroliftDevice.button = strtoul(XdrvMailbox.data, nullptr, 0);
      DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("msb: %08x"), jaroliftDevice.device_key_msb);
      DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("lsb: %08x"), jaroliftDevice.device_key_lsb);
      DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("serial: %08x"), jaroliftDevice.serial);
      DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("disc: %08x"), jaroliftDevice.disc);
      AddLog_P2(LOG_LEVEL_DEBUG, PSTR("KLQ: count: %08x"), jaroliftDevice.count);

      CreateKeeloqPacket();
      jaroliftDevice.count++;
      Settings.keeloq_count = jaroliftDevice.count;

      for(int repeat = 0; repeat <= 1; repeat++)
      {
        uint64_t bitsToSend = jaroliftDevice.pack;
        digitalWrite(jaroliftDevice.port_tx, LOW);
        delayMicroseconds(1150);
        SendSyncPreamble(13);
        delayMicroseconds(3500);
        for(int i=72; i>0; i--)
        {
          SendBit(bitsToSend & 0x0000000000000001);
          bitsToSend >>= 1;
        }
        DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("finished sending bits at %d"), micros());

        delay(16); // delay in loop context is save for wdt
      }
    }
  }

  interrupts();
  enterrx();

  ResponseCmndDone();
}

void SendBit(byte bitToSend)
{
  if (bitToSend==1)
  {
    digitalWrite(jaroliftDevice.port_tx, LOW);  // Simple encoding of bit state 1
    delayMicroseconds(Lowpulse);
    digitalWrite(jaroliftDevice.port_tx, HIGH);
    delayMicroseconds(Highpulse);
  }
  else
  {
    digitalWrite(jaroliftDevice.port_tx, LOW);  // Simple encoding of bit state 0
    delayMicroseconds(Highpulse);
    digitalWrite(jaroliftDevice.port_tx, HIGH);
    delayMicroseconds(Lowpulse);
  }
}

void CmndSendRaw(void)
{
  DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("cmd send called at %d"), micros());
  noInterrupts();
  entertx();
  for(int repeat = 0; repeat <= 1; repeat++)
  {
    if (XdrvMailbox.data_len > 0)
    {
      digitalWrite(jaroliftDevice.port_tx, LOW);
      delayMicroseconds(1150);
      SendSyncPreamble(13);
      delayMicroseconds(3500);

      for(int i=XdrvMailbox.data_len-1; i>=0; i--)
      {
        SendBit(XdrvMailbox.data[i] == '1');
      }
      DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("finished sending bits at %d"), micros());

      delay(16);                       // delay in loop context is save for wdt
    }
    interrupts();
  }
  enterrx();
  ResponseCmndDone();
}

void enterrx() {
  unsigned char marcState = 0;
  cc1101.setRxState();
  delay(2);
  unsigned long rx_time = micros();
  while (((marcState = cc1101.readStatusReg(CC1101_MARCSTATE)) & 0x1F) != 0x0D )
  {
    if (micros() - rx_time > 50000) break; // Quit when marcState does not change...
  }
}

void entertx() {
  unsigned char marcState = 0;
  cc1101.setTxState();
  delay(2);
  unsigned long rx_time = micros();
  while (((marcState = cc1101.readStatusReg(CC1101_MARCSTATE)) & 0x1F) != 0x13 && 0x14 && 0x15)
  {
    if (micros() - rx_time > 50000) break; // Quit when marcState does not change...
  }
}

void SendSyncPreamble(int l)
{
  for (int i = 0; i < l; ++i)
  {
    digitalWrite(jaroliftDevice.port_tx, LOW);
    delayMicroseconds(400);
    digitalWrite(jaroliftDevice.port_tx, HIGH);
    delayMicroseconds(380);
  }
}

void CreateKeeloqPacket()
{
  Keeloq k(jaroliftDevice.device_key_msb, jaroliftDevice.device_key_lsb);
  unsigned int result = (jaroliftDevice.disc << 16) | jaroliftDevice.count;
  jaroliftDevice.pack = (uint64_t)0;
	jaroliftDevice.pack |= jaroliftDevice.serial & 0xfffffffL;
	jaroliftDevice.pack |= (jaroliftDevice.button & 0xfL) << 28;
  jaroliftDevice.pack <<= 32;

  jaroliftDevice.enc = k.encrypt(result);
  jaroliftDevice.pack |= jaroliftDevice.enc;

  AddLog_P2(LOG_LEVEL_DEBUG_MORE, PSTR("pack high: %08x"), jaroliftDevice.pack>>32);
  AddLog_P2(LOG_LEVEL_DEBUG_MORE, PSTR("pack low:  %08x"), jaroliftDevice.pack);
}

void KeeloqInit()
{
  jaroliftDevice.port_tx = pin[GPIO_CC1101_GDO2];              // Output port for transmission
  jaroliftDevice.port_rx = pin[GPIO_CC1101_GDO0];              // Input port for reception

  DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("cc1101.init()"));
  delay(100);
  cc1101.init();
  AddLog_P(LOG_LEVEL_DEBUG_MORE, PSTR("CC1101 done."));
  cc1101.setSyncWord(SYNC_WORD, false);
  cc1101.setCarrierFreq(CFREQ_433);
  cc1101.disableAddressCheck();

  pinMode(jaroliftDevice.port_tx, OUTPUT);
  pinMode(jaroliftDevice.port_rx, INPUT_PULLUP);

  jaroliftDevice.serial = Settings.keeloq_serial;
  jaroliftDevice.count = Settings.keeloq_count;
  GenerateDeviceCryptKey();
}

/*********************************************************************************************\
 * Interface
\*********************************************************************************************/
bool Xdrv36(uint8_t function)
{
  if ((99 == pin[GPIO_CC1101_GDO0]) || (99 == pin[GPIO_CC1101_GDO2])) { return false; }

  bool result = false;

  switch (function) {
    case FUNC_COMMAND:
      AddLog_P(LOG_LEVEL_DEBUG_MORE, PSTR("calling command"));
      result = DecodeCommand(kJaroliftCommands, jaroliftCommand);
      break;
    case FUNC_INIT:
      KeeloqInit();
      DEBUG_DRIVER_LOG(LOG_LEVEL_DEBUG_MORE, PSTR("init done."));
      break;
  }

  return result;
}

#endif // USE_KEELOQ