mirror of https://github.com/arendst/Tasmota.git
Prep release 6.7
This commit is contained in:
Theo Arends
parent
0ebec1fa2e
commit
312ee893f5
28
README.md
28
README.md
|
|
@ -25,11 +25,11 @@ In addition to the [release webpage](https://github.com/arendst/Sonoff-Tasmota/r
|
|||
|
||||
See [sonoff/_changelog.ino](https://github.com/arendst/Sonoff-Tasmota/blob/development/sonoff/_changelog.ino) for detailed change information.
|
||||
|
||||
Unless your Tasmota powered device exhibits a problem or you need to make use of a feature that is not available in the Tasmota version currently installed on your device, leave your device alone - it works so don't make unnecessary changes! If the release version (i.e., the master branch) exhibits unexpected behaviour for your device and configuration, you should upgrade to the latest development version instead to see if your problem is resolved as some bugs in previous releases or development builds may already have been resolved.
|
||||
Unless your Tasmota powered device exhibits a problem or you need to make use of a feature that is not available in the Tasmota version currently installed on your device, leave your device alone - it works so don't make unnecessary changes! If the release version (i.e., the master branch) exhibits unexpected behaviour for your device and configuration, you should upgrade to the latest development version instead to see if your problem is resolved as some bugs in previous releases or development builds may already have been resolved.
|
||||
|
||||
The Tasmota development codebase is checked every 1-2 hours for changes. If new commits have been merged and they compile successfuly, new binary files for every variant (excluding non-English languages) will be posted at http://thehackbox.org/tasmota/ (this web address can be used for OTA updates too). The last compiled commit number is also indicated on the same page. It is important to note that these binaries are based on the current development codebase. These commits are tested as much as is possible and are typically quite stable. However, it is infeasible to test on the hundreds of different types of devices with all the available configuration options permitted.
|
||||
The Tasmota development codebase is checked every 1-2 hours for changes. If new commits have been merged and they compile successfuly, new binary files for every variant (excluding non-English languages) will be posted at http://thehackbox.org/tasmota/ (this web address can be used for OTA updates too). The last compiled commit number is also indicated on the same page. It is important to note that these binaries are based on the current development codebase. These commits are tested as much as is possible and are typically quite stable. However, it is infeasible to test on the hundreds of different types of devices with all the available configuration options permitted.
|
||||
|
||||
Note that there is a chance, as with any upgrade, that the device may not function as expected. You must always account for the possibility that you may need to flash the device via the serial programming interface if the OTA upgrade fails. Even with the master release, you should always attempt to test the device or a similar prototype before upgrading a device which is in production or is hard to reach. And, as always, make a backup of the device configuration before beginning any firmware update.
|
||||
Note that there is a chance, as with any upgrade, that the device may not function as expected. You must always account for the possibility that you may need to flash the device via the serial programming interface if the OTA upgrade fails. Even with the master release, you should always attempt to test the device or a similar prototype before upgrading a device which is in production or is hard to reach. And, as always, make a backup of the device configuration before beginning any firmware update.
|
||||
|
||||
## Disclaimer
|
||||
:warning: **DANGER OF ELECTROCUTION** :warning:
|
||||
|
|
@ -88,17 +88,26 @@ Libraries used with Sonoff-Tasmota are:
|
|||
- [Adafruit CCS811](https://github.com/adafruit/Adafruit_CCS811)
|
||||
- [Adafruit ILI9341](https://github.com/adafruit/Adafruit_ILI9341)
|
||||
- [Adafruit LED Backpack](https://github.com/adafruit/Adafruit-LED-Backpack-Library)
|
||||
- [Adafruit MAX31865](https://github.com/adafruit/Adafruit_MAX31865)
|
||||
- [Adafruit SGP30](https://github.com/adafruit/Adafruit_SGP30)
|
||||
- Adafruit based SH1106
|
||||
- [Adafruit SSD1306](https://github.com/adafruit/Adafruit_SSD1306)
|
||||
- Adafruit based SSD1351
|
||||
- [Adafruit GFX](https://github.com/adafruit/Adafruit-GFX-Library)
|
||||
- Arduino Hex Parser
|
||||
- [ArduinoJson](https://arduinojson.org/)
|
||||
- AT24C256 I2C eeprom
|
||||
- [Base64](https://github.com/Densaugeo/base64_arduino)
|
||||
- [Bear SSL](https://github.com/earlephilhower/bearssl-esp8266.git)
|
||||
- [Bosch BME680](https://github.com/BoschSensortec/BME680_driver)
|
||||
- [C2 Programmer](http://app.cear.ufpb.br/~lucas.hartmann/tag/efm8bb1/)
|
||||
- [esp-epaper-29-ws-20171230-gemu](https://github.com/gemu2015/Sonoff-Tasmota/tree/displays/lib)
|
||||
- [esp-knx-ip](https://github.com/envy/esp-knx-ip)
|
||||
- FrogmoreScd30
|
||||
- FT6236
|
||||
- [I2Cdevlib](https://github.com/jrowberg/i2cdevlib)
|
||||
- [IRremoteEsp8266](https://github.com/markszabo/IRremoteESP8266)
|
||||
- [JaretBurkett ILI9488](https://github.com/jaretburkett/ILI9488)
|
||||
- [JobaTsl2561](https://github.com/joba-1/Joba_Tsl2561)
|
||||
- [LinkedList](https://github.com/ivanseidel/LinkedList)
|
||||
- [Liquid Cristal](https://github.com/marcoschwartz/LiquidCrystal_I2C)
|
||||
|
|
@ -108,6 +117,10 @@ Libraries used with Sonoff-Tasmota are:
|
|||
- [OneWire](https://github.com/PaulStoffregen/OneWire)
|
||||
- [PubSubClient](https://github.com/knolleary/pubsubclient)
|
||||
- [rc-switch](https://github.com/sui77/rc-switch)
|
||||
- TasmotaModbus
|
||||
- TasmotaSerial
|
||||
- [Vl53l0x](https://github.com/pololu/vl53l0x-arduino)
|
||||
- Xlatb Ra8876
|
||||
|
||||
### People inspiring me
|
||||
People helping to keep the show on the road:
|
||||
|
|
@ -132,12 +145,13 @@ People helping to keep the show on the road:
|
|||
- Raymond Mouthaan for managing Wemos Wiki information
|
||||
- Norbert Richter for his decode-config.py tool
|
||||
- Andre Thomas for providing [thehackbox](http://thehackbox.org/tasmota/) OTA support and daily development builds
|
||||
- Joel Stein and digiblur for their Tuya research and driver
|
||||
- Joel Stein, digiblur and Shantur Rathore for their Tuya research and driver
|
||||
- Frogmore42 and Jason2866 for providing many issue answers
|
||||
- Blakadder for editing the wiki and providing template management
|
||||
- Stephan Hadinger for refactoring light driver and enhancing HueEmulation
|
||||
- tmo for designing the official logo
|
||||
- Many more providing Tips, Wips, Pocs or PRs
|
||||
- Stephan Hadinger for refactoring light driver, enhancing HueEmulation and Zigbee support
|
||||
- tmo for designing the official Tasmota logo
|
||||
- Stefan Bode for his Shutter and Deep sleep drivers
|
||||
- Many more providing Tips, Wips, Pocs, PRs and Donations
|
||||
|
||||
## License
|
||||
|
||||
|
|
|
|||
121
RELEASENOTES.md
121
RELEASENOTES.md
|
|
@ -99,6 +99,8 @@ Module | Description
|
|||
71 Sonoff iFan03 | Sonoff iFan03 Wifi Smart Ceiling Fan with Light
|
||||
72 EXS Dimmer | EXS Wifi Dimmer v4
|
||||
|
||||
Over 500 additional devices are supported using [templates](TEMPLATES.md).
|
||||
|
||||
## Provided Binary Downloads
|
||||
The following binary downloads have been compiled with ESP8266/Arduino library core version **pre-2.6.0**.
|
||||
|
||||
|
|
@ -257,5 +259,120 @@ The following binary downloads have been compiled with ESP8266/Arduino library c
|
|||
| USE_DISPLAY_RA8876 | - | - | - | - | - | - | - |
|
||||
|
||||
## Changelog
|
||||
Version 6.7.0 20191101
|
||||
* TBS
|
||||
Version 6.7.0 20191025
|
||||
* Remove support for WPS and SmartConfig in favour of Web server (!) based WifiManager (#6680)
|
||||
* Remove binary sonoff-classic (#6680)
|
||||
* Remove command ``SetOption2``
|
||||
* Remove default DS18B20 driver and only support define **USE_DS18x20** (#6647)
|
||||
* Remove support for define **USE_DS18x20_LEGACY** and legacy DS18x20 driver (#6486)
|
||||
* Replace xsns_23_sdm120 with xnrg_08_sdm120
|
||||
* Replace xsns_25_sdm630 with xnrg_10_sdm630
|
||||
* Replace xsns_49_solaxX1 with xnrg_12_solaxX1 (#6677)
|
||||
* Change Sonoff L1 support by adding define **USE_SONOFF_L1**
|
||||
* Change light drivers internals to ease management
|
||||
* Change command ``PulseTime`` JSON message format and allow display of all pulsetimer information (#6519)
|
||||
* Change command ``SetOption43`` to make it more general. Now supports PS_16_DZ driver too (#6544)
|
||||
* Change command handling by moving buffers up in chain solving ``MQTTlog`` support (#6529)
|
||||
* Change commands ``Var`` and ``Mem`` to show all parameters when no index is given (#6107)
|
||||
* Change detection of non-MQTT commands by allowing non-space characters as delimiter (#6540)
|
||||
* Change rename "Data" to "Hash" and limit to 32 bits when receiving UNKNOWN IR protocol (see DECODE_HASH from IRremoteESP8266)
|
||||
* Change JSON output format for commands ``Adc``, ``Adcs``, ``Modules``, ``Gpio`` and ``Gpios`` from list to dictionary (#6407)
|
||||
* Change energy sensors for three phase/channel support
|
||||
* Change Settings crc calculation allowing short term backward compatibility
|
||||
* Change Improve reliability of TasmotaSerial at 115200 bauds and reduce IRAM usage
|
||||
* Change Tuya support by Shantur Rathore removing commands ``SetOption34, 41, 44, 45, 46 and 65`` (#6353)
|
||||
* Change theoretical baudrate range to 300..19660500 bps in 300 increments (#6294)
|
||||
* Change Settings area to 4k for future use
|
||||
* Change some table locations from RAM to Flash
|
||||
* Change filename of configuration backup from using FriendlyName1 to Hostname solving diacritic issues (#2422)
|
||||
* Change Store AWS IoT Private Key and Certificate in SPI Flash avoiding device-specific compilations
|
||||
* Change defines **USE_TX20_WIND_SENSOR** and **USE_RC_SWITCH** in my_user_config.h to disable to lower iram usage enabling latest core compilation (#6060, #6062)
|
||||
* Fix handling of ligth channels when pwm_multichannel (``SetOption68``) is enabled
|
||||
* Fix better handling of PWM White Temperature mode for Module 48 (#6534)
|
||||
* Fix TasmotaSerial: move serial send to IRAM for high speed baud rates
|
||||
* Fix Domoticz battery level set to 100 if define **USE_ADC_VCC** is not used (#6033)
|
||||
* Fix Force Elliptic Curve for Letsencrypt TLS #6042
|
||||
* Fix WeMo emulation for 1G echo and 2G echo dot (#6086)
|
||||
* Fix Xiaomi Philips brightness (#6091)
|
||||
* Add support for EX-Store WiFi Dimmer V4 (#5856)
|
||||
* Add support for Arduino serial connection (EXPERIMENTAL)
|
||||
* Add support for Zigbee devices Xiaomi lumi.weather air quality sensor, Osram mini-switch
|
||||
* Add support for Zigbee device cc2530 initialization and basic ZCL decoding
|
||||
* Add support for PMS3003 dust particle sensor
|
||||
* Add support for Chint DDSU666 Modbus energy meter by Pablo Zerón
|
||||
* Add support for SM2135 as used in Action LSC Smart Led E14 (#6495)
|
||||
* Add support for Shelly 2.5 dual energy (#6160)
|
||||
* Add support for shutters by Stefan Bode (#288)
|
||||
* Add support for PCF8574 I2C I/O Expander (currently output only) by Stefan Bode
|
||||
* Add support for up to three PZEM-014/-016 on one serial modbus connection with addresses 1 (default), 2 and 3 (#2315)
|
||||
* Add support for up to three PZEM-004T on one serial connection with addresses 192.168.1.1 (default), 2 and 3 (#2315)
|
||||
* Add support for up to three PZEM-003/-017 on one serial modbus connection with addresses 1 (default), 2 and 3 (#2315)
|
||||
* Add support for up to 4 INA226 Voltage and Current sensors by Steve Rogers (#6342)
|
||||
* Add support for A4988 stepper-motor-driver-circuit by Tim Leuschner (#6370)
|
||||
* Add support for Hiking DDS238-2 Modbus energy meter by Matteo Campanella (#6384)
|
||||
* Add support for HM17 bluetooth LE passive scan of ibeacon devices by Gerhard Mutz
|
||||
* Add support for Solax X1 inverter by Pablo Zerón
|
||||
* Add support for PAJ7620 gesture sensor by Christian Baars
|
||||
* Add support for MAX31865 Thermocouple sensor by Alberto Lopez Siemens
|
||||
* Add support for RDM6300 125kHz RFID Reader by Gerhard Mutz
|
||||
* Add support for CHIRP soil moisture sensor by Christian Baars
|
||||
* Add support for Sonoff iFan03 as module 71 (#5988)
|
||||
* Add support for a buzzer
|
||||
* Add support for IRSend long press ('repeat' feature from IRRemoteESP8266) (#6074)
|
||||
* Add support for IRHVAC Midea/Komeco protocol (#3227)
|
||||
* Add support for more IRSend protocols enabled in my_user_config.h
|
||||
* Add support for IRSend Pioneer protocol (#6100)
|
||||
* Add support for up to 4 INA219 sensors (#6046)
|
||||
* Add support for I2C display driver SH1106 oled by Gerhard Mutz
|
||||
* Add support for SPI display drivers epaper 4.2 inch, ILI9488 TFT, SSD1351 Color oled and RA8876 TFT by Gerhard Mutz
|
||||
* Add command ``Buzzer`` with optional parameters <number of beeps>,<duration of beep in 100mS steps>,<duration of silence in 100mS steps> enabled when a buzzer is configured (#5988)
|
||||
* Add command ``DimmerRange`` in Light module to support 2 byte dimming ranges from Tuya
|
||||
* Add command ``DisplayHeight`` to set pixel height on supported devices
|
||||
* Add command ``DisplayWidth`` to set pixel width on supported devices
|
||||
* Add command ``EnergyReset4 x,x`` to initialize total usage for two tarrifs
|
||||
* Add command ``EnergyReset5 x,x`` to initialize total export (or production) for two tarrifs
|
||||
* Add command ``Gpio 255/All`` to show physical GPIO configuration of all non-flash pins (#6407)
|
||||
* Add command ``Gpios 255/All`` to show all available GPIO components (#6407)
|
||||
* Add command ``ModuleAddress 1/2/3`` to set Pzem module address when a single module is connected (#2315)
|
||||
* Add command ``MqttLog <loglevel>`` for support of MQTT logging (#6498)
|
||||
* Add command ``Power0 0/1/2/Off/On/Toggle`` to control all power outputs at once (#6340)
|
||||
* Add command ``PowerDelta 101..32000`` for absolute power delta where 101 = 101-100 = 1W, 202 = 202-100 = 102W (#5901)
|
||||
* Add command ``Reset 99`` to reset bootcount to zero (#684, #6351)
|
||||
* Add command ``Sensor29 pin,0/1/2`` for OFF/ON/TOGGLE
|
||||
* Add command ``Sensor34 8,0`` and ``Sensor34 8,1`` to disable/enable JSON message on weight change over 4 gram
|
||||
* Add command ``SetOption34 0..255`` to set backlog delay. Default value is 200 (mSeconds) (#6562)
|
||||
* Add command ``SetOption42 0..255`` to set overtemperature (Celsius only) threshold resulting in power off all on energy monitoring devices. Default setting is 90 (#6036)
|
||||
* Add command ``SetOption65 0/1`` to disable (1) fast power cycle detection fixing unwanted brownout trigger
|
||||
* Add command ``SetOption66 0/1`` to enable or disable Tuya dimmer range 255 slider control
|
||||
* Add command ``SetOption67 0/1`` to disable or enable a buzzer as used in iFan03
|
||||
* Add command ``SetOption68 0/1`` to enable multi-channel PWM instead of a single light (#6134)
|
||||
* Add command ``SetOption71 0/1`` to switch between different Modbus Active Energy registers on DDS238-2 energy meters (#6531)
|
||||
* Add command ``SetOption72 0/1`` to switch between software (0) or hardware (1) energy total counter (#6561)
|
||||
* Add command ``Time`` to disable NTP and set UTC time as Epoch value if above 1451602800 (=20160101). ``Time 0`` re-enables NTP (#5279)
|
||||
* Add command ``Time 1/2/3`` to select JSON time format ISO + Epoch, ISO or Epoch
|
||||
* Add command ``Tariff`` to default to 0 (=disabled) and allowing to set both Standard Time (ST) and Daylight Savings Time (DST) start hour
|
||||
ex. ``Tariff1 22,23`` = Tariff1 (Off-Peak) ST,DST ``Tariff2 6,7`` = Tariff2 (Standard) ST,DST ``Tariff9 0/1`` = Weekend toggle (1 = Off-Peak during weekend)
|
||||
* Add command ``WebSensor<sensor number> 0/1`` to control display of sensor data in web GUI (#6085)
|
||||
* Add command ``ZigbeeRead`` (#6095)
|
||||
* Add define **USE_DEEPSLEEP** and command ``DeepSleepTime 0 or 10..86400`` (seconds) to enter deepsleep mode (#6638)
|
||||
* Add define **USE_ENERGY_MARGIN_DETECTION** to disable Energy Margin and Power Limit detection
|
||||
* Add define **USE_ENERGY_POWER_LIMIT** to disable Energy Power Limit detection while Energy Margin detection is active
|
||||
* Add define **USE_SONOFF_RF** to enable/disable Sonoff Rf support (#6648)
|
||||
* Add define **USE_WS2812_HARDWARE** to select hardware type WS2812, WS2812X, WS2813, SK6812, LC8812 or APA106 (DMA mode only)
|
||||
* Add incremental beeps to Ifan03 remote control fan speed buttons (#6636)
|
||||
* Add rule support after every command execution like Fanspeed#Data=2 (#6636)
|
||||
* Add WebUI for multiple, independent PWM channels
|
||||
* Add JSON array index support to rules evaluation allowing trigger on ENERGY#POWER[2]>0.60 from JSON ..,"Power":[0.00,0.68],.. (#6160)
|
||||
* Add Full support of all protocols in IRremoteESP8266, to be used on dedicated-IR Tasmota version. Warning: +81k Flash when compiling with **USE_IR_REMOTE_FULL**
|
||||
* Add 'sonoff-ir' pre-packaged IR-dedicated firmware and 'sonoff-ircustom' to customize firmware with IR Full protocol support
|
||||
* Add Tuya Energy monitoring by Shantur Rathore
|
||||
* Add Domoticz P1 Smart Meter support using energy sensors handled by xdrv_03_energy.ino based on an idea by pablozg
|
||||
* Add debug compile features using defines **DEBUG_TASMOTA_CORE**, **DEBUG_TASMOTA_DRIVER** and **DEBUG_TASMOTA_SENSOR**.
|
||||
See **DEBUG_CORE_LOG** example in sonoff.ino and **DEBUG_DRIVER_LOG** example in xdrv_09_timers.ino
|
||||
* Add option 0 to ``Width1`` (Marker), ``Width2`` (Second), ``Width3`` (Minute) and ``Width4`` (Hour) disabling display (#6152)
|
||||
* Add MqttCount metric to STATE (#6155)
|
||||
* Add allow repeat/longpress for IRSend raw, introduced ``IRSend<r>`` option (#6074)
|
||||
* Add Oled reset GPIO option "OLED reset"
|
||||
* Add blend RGB leds with White leds for better whites (#5895, #5704)
|
||||
* Add AZ7798 automatic setting of clock display (#6034)
|
||||
* Add Epoch and UptimeSec to JSON messages (#6068)
|
||||
|
|
|
|||
Loading…
Reference in New Issue