Update Changelog and Release notes

RELEASENOTES.md

@@ -61,7 +61,7 @@ The following binary downloads have been compiled with ESP8266/Arduino library c
 - Change light scheme 2,3,4 cycle time speed from 24,48,72,... seconds to 4,6,12,24,36,48,... seconds (#8034)
 - Change remove floating point libs from IRAM
 - Change remove MQTT Info messages on restart for DeepSleep Wake (#8044)
-- Change IRremoteESP8266 library updated to v2.7.5
+- Change IRremoteESP8266 library updated to v2.7.6
 - Fix possible Relay toggle on (OTA) restart
 - Fix PWM flickering during wifi connection (#8046)
 - Fix Zigbee sending wrong Sat value with Hue emulation
@@ -78,6 +78,7 @@ The following binary downloads have been compiled with ESP8266/Arduino library c
 - Add command ``SetOption73 1`` for button decoupling and send multi-press and hold MQTT messages by Federico Leoni (#8235)
 - Add command ``SetOption90 1`` to disable non-json MQTT messages (#8044)
 - Add command ``SetOption91 1`` to enable fading at startup / power on
+- Add command ``SetOption92 1`` to set PWM Mode from regular PWM to ColorTemp control (Xiaomi Philips ...)
 - Add command ``Sensor10 0/1/2`` to control BH1750 resolution - 0 = High (default), 1 = High2, 2 = Low (#8016)
 - Add command ``Sensor10 31..254`` to control BH1750 measurement time which defaults to 69 (#8016)
 - Add command ``Sensor18 0..32000`` to control PMS5003 sensor interval to extend lifetime by Gene Ruebsamen (#8128)

tasmota/CHANGELOG.md

@@ -12,6 +12,7 @@
 - Fix Zigbee DimmerUp/DimmerDown malformed
 - Add config version tag
 - Add command ``SetOption73 1`` for button decoupling and send multi-press and hold MQTT messages by Federico Leoni (#8235)
+- Add command ``SetOption92 1`` to set PWM Mode from regular PWM to ColorTemp control (Xiaomi Philips ...)
 - Add command ``SO`` as shortcut for command ``SetOption``
 
 ### 8.2.0.3 20200329

tasmota/settings.h

@@ -111,7 +111,7 @@ typedef union {                            // Restricted by MISRA-C Rule 18.4 bu
     uint32_t zigbee_distinct_topics : 1;   // bit 7 (v8.1.0.10)  - SetOption89 - Distinct MQTT topics per device for Zigbee (#7835)
     uint32_t only_json_message : 1;        // bit 8 (v8.2.0.3)   - SetOption90 - Disable non-json MQTT response
     uint32_t fade_at_startup : 1;          // bit 9 (v8.2.0.3)   - SetOption91 - Enable light fading at start/power on
-    uint32_t pwm_ct_mode : 1;              // bit 10 ()          - SetOption92 - Set PWM Mode from regular PWM to ColorTemp control (Xiaomi Philips ...)
+    uint32_t pwm_ct_mode : 1;              // bit 10 (v8.2.0.4)  - SetOption92 - Set PWM Mode from regular PWM to ColorTemp control (Xiaomi Philips ...)
     uint32_t spare11 : 1;
     uint32_t spare12 : 1;
     uint32_t spare13 : 1;

tasmota/xsns_02_analog.ino

@@ -167,26 +167,25 @@ void AdcGetCurrentPower(uint8_t factor)
   uint16_t analog_min = 1023;
   uint16_t analog_max = 0;
 
-  if(Settings.adc_param1==0){
-  for (uint32_t i = 0; i < samples; i++) {
-    analog = analogRead(A0);
-    if (analog < analog_min) {
-      analog_min = analog;
+  if (0 == Settings.adc_param1) {
+    for (uint32_t i = 0; i < samples; i++) {
+      analog = analogRead(A0);
+      if (analog < analog_min) {
+        analog_min = analog;
+      }
+      if (analog > analog_max) {
+        analog_max = analog;
+      }
+      delay(1);
     }
-    if (analog > analog_max) {
-      analog_max = analog;
-    }
-    delay(1);
+    Adc.current = (float)(analog_max-analog_min) * ((float)(Settings.adc_param2) / 100000);
   }
-  Adc.current = (float)(analog_max-analog_min) * ((float)(Settings.adc_param2) / 100000);
-  } 
-  else{
-
+  else {
     analog = AdcRead(5);
-    if(analog>Settings.adc_param1){
+    if (analog > Settings.adc_param1) {
      Adc.current = ((float)(analog) - (float)Settings.adc_param1) * ((float)(Settings.adc_param2) / 100000);
     }
-    else{
+    else {
       Adc.current = 0;
     }
   }
@@ -370,7 +369,7 @@ void CmndAdcParam(void)
           Settings.adc_param3 = (int)(CharToFloat(subStr(sub_string, XdrvMailbox.data, ",", 4)) * 10000);
         }
         if (ADC0_CT_POWER == XdrvMailbox.payload) {
-          if ((Settings.adc_param1 == 1 & CT_FLAG_ENERGY_RESET) > 0) {
+          if (((1 == Settings.adc_param1) & CT_FLAG_ENERGY_RESET) > 0) {
             Adc.energy = 0;
             Settings.adc_param1 ^= CT_FLAG_ENERGY_RESET;  // Cancel energy reset flag
           }

tools/decode-status.py

@@ -126,7 +126,7 @@ a_setoption = [[
     "Enable Weekend Energy Tariff",
     "Select different Modbus registers for Active Energy",
     "Enable hardware energy total counter as reference",
-    "Enable HTTP CORS",
+    "Detach buttons from relays and enable MQTT action state for multipress",
     "Enable internal pullup for single DS18x20 sensor",
     "GroupTopic replaces %topic% (0) or fixed topic cmnd/grouptopic (1)",
     "Enable incrementing bootcount when deepsleep is enabled",
@@ -146,7 +146,7 @@ a_setoption = [[
     "Distinct MQTT topics per device for Zigbee",
     "Disable non-json MQTT response",
     "Enable light fading at start/power on",
-    "","",
+    "Set PWM Mode from regular PWM to ColorTemp control","",
     "","","","",
     "","","","",
     "","","","",
@@ -241,7 +241,7 @@ else:
         obj = json.load(fp)
 
 def StartDecode():
-    print ("\n*** decode-status.py v20200411 by Theo Arends and Jacek Ziolkowski ***")
+    print ("\n*** decode-status.py v20200428 by Theo Arends and Jacek Ziolkowski ***")
 
 #    print("Decoding\n{}".format(obj))