v3.9.6

3.9.6 20170129
* Add dynamic sleep for WS2812 animation (#1)

README.md

@@ -1,7 +1,7 @@
 ## Sonoff-Tasmota
 Provide ESP8266 based Sonoff by [iTead Studio](https://www.itead.cc/) and ElectroDragon IoT Relay with Serial, Web and MQTT control allowing 'Over the Air' or OTA firmware updates using Arduino IDE.
 
-Current version is **3.9.5** - See ```sonoff/_releasenotes.ino``` for change information.
+Current version is **3.9.6** - See ```sonoff/_releasenotes.ino``` for change information.
 
 - This version provides all (Sonoff) modules in one file and starts up with Sonoff Basic.
 - Once uploaded select module using the configuration webpage or the commands ```Modules``` and ```Module```.
@@ -11,7 +11,7 @@ Current version is **3.9.5** - See ```sonoff/_releasenotes.ino``` for change inf
 See [Wiki](wiki) for more information.<br />
 See [Community](https://groups.google.com/d/forum/sonoffusers) for forum and more user experience.
 
-The following devices are supported:
+Starting with version 2.0.0 the following devices are supported:
 - [iTead Sonoff Basic](http://sonoff.itead.cc/en/products/sonoff/sonoff-basic)
 - [iTead Sonoff RF](http://sonoff.itead.cc/en/products/sonoff/sonoff-rf)
 - [iTead Sonoff SV](https://www.itead.cc/sonoff-sv.html)

sonoff/_releasenotes.ino

@@ -1,4 +1,7 @@
-/* 3.9.5 2017018
+/* 3.9.6 20170129
+ * Add dynamic sleep for WS2812 animation (#1)
+ *
+ * 3.9.5 20170128
  * Fix error message in case of wrong Domoticz command
  *
  * 3.9.4 20170127

sonoff/sonoff.ino

@@ -10,7 +10,7 @@
  * ====================================================
 */
 
-#define VERSION                0x03090500   // 3.9.5
+#define VERSION                0x03090600   // 3.9.6
 
 enum log_t   {LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE, LOG_LEVEL_ALL};
 enum week_t  {Last, First, Second, Third, Fourth};
@@ -383,6 +383,7 @@ byte syslog_level;                    // Current copy of sysCfg.syslog_level
 uint16_t syslog_timer = 0;            // Timer to re-enable syslog_level
 byte seriallog_level;                 // Current copy of sysCfg.seriallog_level
 uint16_t seriallog_timer = 0;         // Timer to disable Seriallog
+uint8_t sleep;                        // Current copy of sysCfg.sleep
 
 int blinks = 201;                     // Number of LED blinks
 uint8_t blinkstate = 0;               // LED state
@@ -1283,9 +1284,10 @@ void mqttDataCb(char* topic, byte* data, unsigned int data_len)
     else if (!strcmp(type,"SLEEP")) {
       if ((data_len > 0) && (payload >= 0) && (payload < 251)) {
         sysCfg.sleep = payload;
-        restartflag = 2;
+        sleep = payload;
+//        restartflag = 2;
       }
-      snprintf_P(svalue, sizeof(svalue), PSTR("{\"Sleep\":\"%d%s\"}"), sysCfg.sleep, (sysCfg.value_units) ? " mS" : "");
+      snprintf_P(svalue, sizeof(svalue), PSTR("{\"Sleep\":\"%d%s (%d%s)\"}"), sleep, (sysCfg.value_units) ? " mS" : "", sysCfg.sleep, (sysCfg.value_units) ? " mS" : "");
     }
     else if (!strcmp(type,"UPGRADE") || !strcmp(type,"UPLOAD")) {
       if ((data_len > 0) && (payload == 1)) {
@@ -2456,6 +2458,7 @@ void setup()
   seriallog_timer = SERIALLOG_TIMER;
   seriallog_level = sysCfg.seriallog_level;
   syslog_level = sysCfg.syslog_level;
+  sleep = sysCfg.sleep;
 
   GPIO_init();
 
@@ -2525,7 +2528,7 @@ void loop()
   if (millis() >= timerxs) stateloop();
   if (sysCfg.mqtt_enabled) mqttClient.loop();
   if (Serial.available()) serial();
-  yield();
 
-  if (sysCfg.sleep) delay(sysCfg.sleep);
+//  yield();     // yield == delay(0), delay contains yield, auto yield in loop
+  delay(sleep);  // https://github.com/esp8266/Arduino/issues/2021
 }

sonoff/support.ino

@@ -421,7 +421,8 @@ void WIFI_begin(uint8_t flag)
   }
   WiFi.disconnect();
   WiFi.mode(WIFI_STA);      // Disable AP mode
-  if (sysCfg.sleep) wifi_set_sleep_type(LIGHT_SLEEP_T);  // Allow light sleep during idle times
+//  if (sysCfg.sleep) wifi_set_sleep_type(LIGHT_SLEEP_T);  // Allow light sleep during idle times
+  WiFi.setSleepMode(WIFI_LIGHT_SLEEP);  // Allow light sleep during idle times
 //  if (WiFi.getPhyMode() != WIFI_PHY_MODE_11N) WiFi.setPhyMode(WIFI_PHY_MODE_11N);
   if (!WiFi.getAutoConnect()) WiFi.setAutoConnect(true);
 //  WiFi.setAutoReconnect(true);

sonoff/xdrv_ws2812.ino

@@ -372,10 +372,12 @@ void ws2812_animate()
   
   stripTimerCntr++;
   if (power == 0) {  // Power Off
+    sleep = sysCfg.sleep;
     stripTimerCntr = 0;
     tcolor = 0;
   }
   else {
+    sleep = 0;
     switch (sysCfg.ws_scheme) {
       case 0:  // Power On
         ws2812_setDim(sysCfg.ws_dimmer);

sonoff/xsns_hlw8012.ino

@@ -29,7 +29,7 @@ POSSIBILITY OF SUCH DAMAGE.
  * Based on Source: Shenzhen Heli Technology Co., Ltd
 \*********************************************************************************************/
 
-#define FEATURE_POWER_LIMIT  false
+#define FEATURE_POWER_LIMIT  true
 
 /*********************************************************************************************/
 
@@ -512,8 +512,8 @@ boolean hlw_command(char *type, uint16_t index, char *dataBuf, uint16_t data_len
 
 void hlw_commands(char *svalue, uint16_t ssvalue)
 {
-  snprintf_P(svalue, ssvalue, PSTR("{\"Commands\":\"PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow, CurrentHigh%s\"}"),
-    (FEATURE_POWER_LIMIT)?"SafePower, SafePowerHold, SafePowerWindow, MaxPower, MaxPowerHold, MaxPowerWindow, MaxEnergy, MaxEnergyStart":"");
+  snprintf_P(svalue, ssvalue, PSTR("{\"Commands\":\"PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow, CurrentHigh, HlwPcal, HlwUcal, HlwIcal%s\"}"),
+    (FEATURE_POWER_LIMIT)?", SafePower, SafePowerHold, SafePowerWindow, MaxPower, MaxPowerHold, MaxPowerWindow, MaxEnergy, MaxEnergyStart":"");
 }
 
 /*********************************************************************************************\