v5.11.1j - Change uptime to seconds

5.11.1j
 * Prep for release
 * Change uptime from hour to second
resulting in a display of 123T13:45:21 where 123 is days
 * Fix Arilux
RF induced exception by moving interrupt handler to iram on non
esp/arduino lib v2.3.0
 * Add NTP sync based on chip id (#1773)

README.md

@@ -1,7 +1,7 @@
 ## Sonoff-Tasmota
 Provide ESP8266 based Sonoff by [iTead Studio](https://www.itead.cc/) and ElectroDragon IoT Relay with Serial, Web and MQTT control allowing 'Over the Air' or OTA firmware updates using Arduino IDE.
 
-Current version is **5.11.1i** - See [sonoff/_releasenotes.ino](https://github.com/arendst/Sonoff-Tasmota/blob/development/sonoff/_releasenotes.ino) for change information.
+Current version is **5.11.1j** - See [sonoff/_releasenotes.ino](https://github.com/arendst/Sonoff-Tasmota/blob/development/sonoff/_releasenotes.ino) for change information.
 
 ### ATTENTION All versions
 

sonoff/_releasenotes.ino

@@ -1,4 +1,10 @@
-/* 5.11.1i
+/* 5.11.1j
+ * Prep for release
+ * Change uptime from hour to second resulting in a display of 123T13:45:21 where 123 is days
+ * Fix Arilux RF induced exception by moving interrupt handler to iram on non esp/arduino lib v2.3.0
+ * Add NTP sync based on chip id (#1773)
+ *
+ * 5.11.1i
  * Update TasmotaSerial library to 1.1.0
  * Rename commands HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to be used for both Pow and S31 calibration
  * Rename commands HlwPSet, HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used for both Pow and S31 calibration

sonoff/settings.h

@@ -270,6 +270,7 @@ struct TIME_T {
   char          name_of_month[4];
   uint16_t      day_of_year;
   uint16_t      year;
+  unsigned long days;
   unsigned long valid;
 } RtcTime;
 

sonoff/sonoff.ino

@@ -25,7 +25,7 @@
     - Select IDE Tools - Flash Size: "1M (no SPIFFS)"
   ====================================================*/
 
-#define VERSION                0x050B0109   // 5.11.1i
+#define VERSION                0x050B010A   // 5.11.1j
 
 // Location specific includes
 #include <core_version.h>                   // Arduino_Esp8266 version information (ARDUINO_ESP8266_RELEASE and ARDUINO_ESP8266_RELEASE_2_3_0)
@@ -126,7 +126,8 @@ byte ota_retry_counter = OTA_ATTEMPTS;      // OTA retry counter
 char *ota_url;                              // OTA url string
 int restart_flag = 0;                       // Sonoff restart flag
 int wifi_state_flag = WIFI_RESTART;         // Wifi state flag
-int uptime = 0;                             // Current uptime in hours
+//int uptime = 0;                             // Current uptime in hours
+uint32_t uptime = 0;                        // Counting every second until 4294967295 = 130 year
 boolean latest_uptime_flag = true;          // Signal latest uptime
 int tele_period = 0;                        // Tele period timer
 byte web_log_index = 1;                     // Index in Web log buffer (should never be 0)
@@ -1714,8 +1715,8 @@ void PublishStatus(uint8_t payload)
   }
 
   if ((0 == payload) || (1 == payload)) {
-    snprintf_P(mqtt_data, sizeof(mqtt_data), PSTR("{\"" D_CMND_STATUS D_STATUS1_PARAMETER "\":{\"" D_JSON_BAUDRATE "\":%d,\"" D_CMND_GROUPTOPIC "\":\"%s\",\"" D_CMND_OTAURL "\":\"%s\",\"" D_JSON_UPTIME "\":%d,\"" D_CMND_SLEEP "\":%d,\"" D_JSON_BOOTCOUNT "\":%d,\"" D_JSON_SAVECOUNT "\":%d,\"" D_JSON_SAVEADDRESS "\":\"%X\"}}"),
+    snprintf_P(mqtt_data, sizeof(mqtt_data), PSTR("{\"" D_CMND_STATUS D_STATUS1_PARAMETER "\":{\"" D_JSON_BAUDRATE "\":%d,\"" D_CMND_GROUPTOPIC "\":\"%s\",\"" D_CMND_OTAURL "\":\"%s\",\"" D_JSON_UPTIME "\":\"%s\",\"" D_CMND_SLEEP "\":%d,\"" D_JSON_BOOTCOUNT "\":%d,\"" D_JSON_SAVECOUNT "\":%d,\"" D_JSON_SAVEADDRESS "\":\"%X\"}}"),
-      baudrate, Settings.mqtt_grptopic, Settings.ota_url, uptime, Settings.sleep, Settings.bootcount, Settings.save_flag, GetSettingsAddress());
+      baudrate, Settings.mqtt_grptopic, Settings.ota_url, GetUptime().c_str(), Settings.sleep, Settings.bootcount, Settings.save_flag, GetSettingsAddress());
     MqttPublishPrefixTopic_P(option, PSTR(D_CMND_STATUS "1"));
   }
 
@@ -1788,7 +1789,7 @@ void MqttShowState()
 {
   char stemp1[33];
 
-  snprintf_P(mqtt_data, sizeof(mqtt_data), PSTR("%s{\"" D_JSON_TIME "\":\"%s\",\"" D_JSON_UPTIME "\":%d"), mqtt_data, GetDateAndTime().c_str(), uptime);
+  snprintf_P(mqtt_data, sizeof(mqtt_data), PSTR("%s{\"" D_JSON_TIME "\":\"%s\",\"" D_JSON_UPTIME "\":\"%s\""), mqtt_data, GetDateAndTime().c_str(), GetUptime().c_str());
 #ifdef USE_ADC_VCC
   dtostrfd((double)ESP.getVcc()/1000, 3, stemp1);
   snprintf_P(mqtt_data, sizeof(mqtt_data), PSTR("%s,\"" D_JSON_VCC "\":%s"), mqtt_data, stemp1);
@@ -1833,6 +1834,8 @@ boolean MqttShowSensor()
 
 void PerformEverySecond()
 {
+  uptime++;
+
   if (blockgpio0) {
     blockgpio0--;
   }
@@ -1897,8 +1900,7 @@ void PerformEverySecond()
 
   if ((2 == RtcTime.minute) && latest_uptime_flag) {
     latest_uptime_flag = false;
-    uptime++;
+    snprintf_P(mqtt_data, sizeof(mqtt_data), PSTR("{\"" D_JSON_TIME "\":\"%s\",\"" D_JSON_UPTIME "\":\"%s\"}"), GetDateAndTime().c_str(), GetUptime().c_str());
-    snprintf_P(mqtt_data, sizeof(mqtt_data), PSTR("{\"" D_JSON_TIME "\":\"%s\",\"" D_JSON_UPTIME "\":%d}"), GetDateAndTime().c_str(), uptime);
     MqttPublishPrefixTopic_P(TELE, PSTR(D_RSLT_UPTIME));
   }
   if ((3 == RtcTime.minute) && !latest_uptime_flag) {

sonoff/sonoff_post.h

@@ -82,9 +82,21 @@ void WifiWpsStatusCallback(wps_cb_status status);
 #ifdef USE_DHT
 #undef USE_DHT                              // Disable internal DHT sensor
 #endif
+#ifdef USE_DISPLAY
+#undef USE_DISPLAY                          // Disable Display support
+#endif
+#ifdef USE_MHZ19
+#undef USE_MHZ19                            // Disable support for MH-Z19 CO2 sensor
+#endif
+#ifdef USE_SENSEAIR
+#undef USE_SENSEAIR                         // Disable support for SenseAir K30, K70 and S8 CO2 sensor
+#endif
 #ifdef USE_IR_REMOTE
 #undef USE_IR_REMOTE                        // Disable IR driver
 #endif
+#ifdef USE_ARILUX_RF
+#undef USE_ARILUX_RF                        // Disable support for Arilux RF remote controller
+#endif
 #ifdef DEBUG_THEO
 #undef DEBUG_THEO                           // Disable debug code
 #endif

sonoff/support.ino

@@ -993,6 +993,7 @@ uint32_t standard_time = 0;
 uint32_t ntp_time = 0;
 uint32_t midnight = 1451602800;
 uint8_t  midnight_now = 0;
+uint8_t  ntp_sync_minute = 0;
 
 String GetBuildDateAndTime()
 {
@@ -1047,6 +1048,22 @@ String GetUtcDateAndTime()
   return String(dt);
 }
 
+String GetUptime()
+{
+  char dt[16];
+
+  TIME_T ut;
+  BreakTime(uptime, ut);
+
+  // "P128DT14H35M44S" - ISO8601:2004 - https://en.wikipedia.org/wiki/ISO_8601 Durations
+//  snprintf_P(dt, sizeof(dt), PSTR("P%dDT%02dH%02dM%02dS"), ut.days, ut.hour, ut.minute, ut.second);
+
+  // "128 14:35:44" - OpenVMS
+  // "128T14:35:44" - Tasmota
+  snprintf_P(dt, sizeof(dt), PSTR("%d" D_DATE_TIME_SEPARATOR "%02d" D_HOUR_MINUTE_SEPARATOR "%02d" D_MINUTE_SECOND_SEPARATOR "%02d"), ut.days, ut.hour, ut.minute, ut.second);
+  return String(dt);
+}
+
 void BreakTime(uint32_t time_input, TIME_T &tm)
 {
 // break the given time_input into time components
@@ -1066,6 +1083,7 @@ void BreakTime(uint32_t time_input, TIME_T &tm)
   time /= 60;                // now it is hours
   tm.hour = time % 24;
   time /= 24;                // now it is days
+  tm.days = time;
   tm.day_of_week = ((time + 4) % 7) + 1;  // Sunday is day 1
 
   year = 0;
@@ -1201,22 +1219,13 @@ boolean MidnightNow()
 
 void RtcSecond()
 {
-  byte ntpsync;
   uint32_t stdoffset;
   uint32_t dstoffset;
   TIME_T tmpTime;
 
-  ntpsync = 0;
+  if ((ntp_sync_minute > 59) && (3 == RtcTime.minute)) ntp_sync_minute = 1;                // If sync prepare for a new cycle
-  if (RtcTime.year < 2016) {
+  uint8_t offset = (uptime < 30) ? RtcTime.second : (((ESP.getChipId() & 0xF) * 3) + 3) ;  // First try ASAP to sync. If fails try once every 60 seconds based on chip id
-    if (WL_CONNECTED == WiFi.status()) {
+  if ((WL_CONNECTED == WiFi.status()) && (offset == RtcTime.second) && ((RtcTime.year < 2016) || (ntp_sync_minute == RtcTime.minute))) {
-      ntpsync = 1;  // Initial NTP sync
-    }
-  } else {
-    if ((1 == RtcTime.minute) && (1 == RtcTime.second)) {
-      ntpsync = 1;  // Hourly NTP sync at xx:01:01
-    }
-  }
-  if (ntpsync) {
     ntp_time = sntp_get_current_timestamp();
     if (ntp_time) {
       utc_time = ntp_time;
@@ -1230,6 +1239,9 @@ void RtcSecond()
       AddLog(LOG_LEVEL_DEBUG);
       snprintf_P(log_data, sizeof(log_data), PSTR(D_LOG_APPLICATION "(" D_STD_TIME ") %s"), GetTime(3).c_str());
       AddLog(LOG_LEVEL_DEBUG);
+      ntp_sync_minute = 60;  // Sync so block further requests
+    } else {
+      ntp_sync_minute++;     // Try again in next minute
     }
   }
   utc_time++;

sonoff/user_config.h

@@ -169,11 +169,10 @@
 #define PRESSURE_RESOLUTION    1                 // [PressRes] Maximum number of decimals (0 - 3) showing sensor Pressure
 #define ENERGY_RESOLUTION      3                 // [EnergyRes] Maximum number of decimals (0 - 5) showing energy usage in kWh
 
-// -- Sensor code selection -----------------------
+// -- Internal Analog input -----------------------
 #define USE_ADC_VCC                              // Display Vcc in Power status. Disable for use as Analog input on selected devices
 
-#define USE_PZEM004T                             // Add support for PZEM004T Energy monitor (+2k code)
+// -- One wire sensors ----------------------------
-
                                                  // WARNING: Select none for default one DS18B20 sensor or enable one of the following two options for multiple sensors
 //#define USE_DS18x20                              // Optional for more than one DS18x20 sensors with id sort, single scan and read retry (+1k3 code)
 //#define USE_DS18x20_LEGACY                       // Optional for more than one DS18x20 sensors with dynamic scan using library OneWire (+1k5 code)
@@ -185,39 +184,24 @@
   #define USE_SHT3X                              // Add I2C code for SHT3x sensor (+0k6 code)
   #define USE_HTU                                // Add I2C code for HTU21/SI7013/SI7020/SI7021 sensor (+1k5 code)
   #define USE_BMP                                // Add I2C code for BMP085/BMP180/BMP280/BME280 sensor (+4k code)
-    #define USE_BME680                           // Add additional support for BME680 sensor using Adafruit Sensor and BME680 libraries (+6k code)
+//    #define USE_BME680                           // Add additional support for BME680 sensor using Adafruit Sensor and BME680 libraries (+6k code)
   #define USE_BH1750                             // Add I2C code for BH1750 sensor (+0k5 code)
 //  #define USE_VEML6070                           // Add I2C code for VEML6070 sensor (+0k5 code)
 //  #define USE_TSL2561                            // Add I2C code for TSL2561 sensor using library Adafruit TSL2561 Arduino (+1k2 code)
 //  #define USE_ADS1115                            // Add I2C code for ADS1115 16 bit A/D converter based on Adafruit ADS1x15 library (no library needed) (+0k7 code)
 //  #define USE_ADS1115_I2CDEV                     // Add I2C code for ADS1115 16 bit A/D converter using library i2cdevlib-Core and i2cdevlib-ADS1115 (+2k code)
 //  #define USE_INA219                             // Add I2C code for INA219 Low voltage and current sensor (+1k code)
-//  #define USE_DISPLAY                            // Add I2C Display Support for LCD, Oled and up to eigth Matrices (+19k code)
-    #define MTX_ADDRESS1       0x71              // [DisplayAddress[1]] I2C address of first 8x8 matrix module
-    #define MTX_ADDRESS2       0x74              // [DisplayAddress[2]] I2C address of second 8x8 matrix module
-    #define MTX_ADDRESS3       0x75              // [DisplayAddress[3]] I2C address of third 8x8 matrix module
-    #define MTX_ADDRESS4       0x72              // [DisplayAddress[4]] I2C address of fourth 8x8 matrix module
-    #define MTX_ADDRESS5       0x73              // [DisplayAddress[5]] I2C address of fifth 8x8 matrix module
-    #define MTX_ADDRESS6       0x76              // [DisplayAddress[6]] I2C address of sixth 8x8 matrix module
-    #define MTX_ADDRESS7       0x00              // [DisplayAddress[7]] I2C address of seventh 8x8 matrix module
-    #define MTX_ADDRESS8       0x00              // [DisplayAddress[8]] I2C address of eigth 8x8 matrix module
 #endif  // USE_I2C
 
-//#define USE_SPI                                  // SPI using library TasmotaTFT
+// -- Serial sensors ------------------------------
-#ifdef USE_SPI
-  #ifndef USE_DISPLAY
-  #define USE_DISPLAY                            // Add SPI Display support for 320x240 and 480x320 TFT
-  #endif
-#endif  // USE_SPI
-
-// -- Carbon dioxide (CO2) sensors ----------------
 #define USE_MHZ19                                // Add support for MH-Z19 CO2 sensor (+2k code)
 #define USE_SENSEAIR                             // Add support for SenseAir K30, K70 and S8 CO2 sensor (+2k3 code)
   #define CO2_LOW              800               // Below this CO2 value show green light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
   #define CO2_HIGH             1200              // Above this CO2 value show red light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
-
 #define USE_PMS5003                              // Add support for PMS5003 and PMS7003 particle concentration sensor (+1k3 code)
+#define USE_PZEM004T                             // Add support for PZEM004T Energy monitor (+2k code)
 
+// -- Low level interface devices -----------------
 #define USE_IR_REMOTE                            // Send IR remote commands using library IRremoteESP8266 and ArduinoJson (+4k code, 0k3 mem, 48 iram)
 //  #define USE_IR_HVAC                            // Support for HVAC system using IR (+2k code)
   #define USE_IR_RECEIVE                         // Support for IR receiver (+5k5 code, 264 iram)
@@ -226,7 +210,7 @@
   #define USE_WS2812_CTYPE     1                 // WS2812 Color type (0 - RGB, 1 - GRB, 2 - RGBW, 3 - GRBW)
 //  #define USE_WS2812_DMA                         // DMA supports only GPIO03 (= Serial RXD) (+1k mem). When USE_WS2812_DMA is enabled expect Exceptions on Pow
 
-#define USE_ARILUX_RF                            // Add support for Arilux RF remote controller (+0k8 code)
+#define USE_ARILUX_RF                            // Add support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0))
 
 /*********************************************************************************************\
  * Compile a minimal version if upgrade memory gets tight ONLY TO BE USED FOR UPGRADE STEP 1!

sonoff/webserver.ino

@@ -1328,6 +1328,9 @@ void HandleUploadLoop()
 #ifdef USE_EMULATION
       UdpDisconnect();
 #endif  // USE_EMULATION
+#ifdef USE_ARILUX_RF
+      AriluxRfDisable();  // Prevent restart exception on Arilux Interrupt routine
+#endif  // USE_ARILUX_RF
       if (Settings.flag.mqtt_enabled) {
         MqttClient.disconnect();
       }
@@ -1593,7 +1596,8 @@ void HandleInformation()
   func += F(D_PROGRAM_VERSION "}2"); func += my_version;
   func += F("}1" D_BUILD_DATE_AND_TIME "}2"); func += GetBuildDateAndTime();
   func += F("}1" D_CORE_AND_SDK_VERSION "}2" ARDUINO_ESP8266_RELEASE "/"); func += String(ESP.getSdkVersion());
-  func += F("}1" D_UPTIME "}2"); func += String(uptime); func += F(" Hours");
+//  func += F("}1" D_UPTIME "}2"); func += String(uptime); func += F(" Seconds");
+  func += F("}1" D_UPTIME "}2"); func += GetUptime();
   snprintf_P(stopic, sizeof(stopic), PSTR(" at %X"), GetSettingsAddress());
   func += F("}1" D_FLASH_WRITE_COUNT "}2"); func += String(Settings.save_flag); func += stopic;
   func += F("}1" D_BOOT_COUNT "}2"); func += String(Settings.bootcount);

sonoff/xdrv_01_light.ino

@@ -133,9 +133,12 @@ unsigned int arilux_rf_repeat_count = 0;
 
 uint8_t arilux_rf_toggle = 0;
 
+
+#ifndef ARDUINO_ESP8266_RELEASE_2_3_0
 #ifndef USE_WS2812_DMA  // Collides with Neopixelbus but solves RF misses
-//void AriluxRfInterrupt() ICACHE_RAM_ATTR;  // As iram is tight and it works this way too
+void AriluxRfInterrupt() ICACHE_RAM_ATTR;  // As iram is tight and it works this way too
 #endif  // USE_WS2812_DMA
+#endif  // ARDUINO_ESP8266_RELEASE_2_3_0
 
 void AriluxRfInterrupt()
 {
@@ -366,13 +369,9 @@ void LightInit()
       }
     }
     if (pin[GPIO_ARIRFRCV] < 99) {
-#ifdef USE_ARILUX_RF
-      AriluxRfInit();
-#else
       if (pin[GPIO_LED2] < 99) {
         digitalWrite(pin[GPIO_LED2], bitRead(led_inverted, 1));  // Turn off RF
       }
-#endif  // USE_ARILUX_RF
     }
   }
 #ifdef USE_WS2812  // ************************************************************************
@@ -1225,11 +1224,14 @@ boolean Xdrv01(byte function)
       case FUNC_EVERY_50_MSECOND:
         LightAnimate();
 #ifdef USE_ARILUX_RF
-        if (pin[GPIO_ARIRFRCV] < 99) {
+        if (pin[GPIO_ARIRFRCV] < 99) AriluxRfHandler();
-          AriluxRfHandler();
-        }
 #endif  // USE_ARILUX_RF
         break;
+#ifdef USE_ARILUX_RF
+      case FUNC_EVERY_SECOND:
+        if (10 == uptime) AriluxRfInit();  // Needs rest before enabling RF interrupts
+        break;
+#endif  // USE_ARILUX_RF
       case FUNC_COMMAND:
         result = LightCommand();
         break;