mirror of https://github.com/arendst/Tasmota.git
Add a stripped down Add a stripped DHT driver based on ESPEasy (#7717)
Add a stripped DHT driver based on ESPEasy (#7717)
This commit is contained in:
Theo Arends
parent
a7e9058d3b
commit
e9f0c5b6d6
|
|
@ -17,7 +17,7 @@
|
|||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifdef USE_DHT
|
||||
#ifdef USE_DHT_V3
|
||||
/*********************************************************************************************\
|
||||
* DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321), SI7021 - Temperature and Humidy
|
||||
*
|
||||
|
|
|
|||
|
|
@ -0,0 +1,291 @@
|
|||
/*
|
||||
xsns_06_dht.ino - DHTxx, AM23xx and SI7021 temperature and humidity sensor support for Tasmota
|
||||
|
||||
Copyright (C) 2020 Theo Arends
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 3 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifdef USE_DHT
|
||||
/*********************************************************************************************\
|
||||
* DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321), SI7021 - Temperature and Humidy
|
||||
*
|
||||
* Reading temperature or humidity takes about 250 milliseconds!
|
||||
* Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
|
||||
*
|
||||
* This version is based on ESPEasy _P005_DHT.ino 20191201 and stripped
|
||||
\*********************************************************************************************/
|
||||
|
||||
#define XSNS_06 6
|
||||
|
||||
#define DHT_MAX_SENSORS 4
|
||||
#define DHT_MAX_RETRY 8
|
||||
|
||||
uint8_t dht_data[5];
|
||||
uint8_t dht_sensors = 0;
|
||||
uint8_t dht_pin_out = 0; // Shelly GPIO00 output only
|
||||
bool dht_active = true; // DHT configured
|
||||
bool dht_dual_mode = false; // Single pin mode
|
||||
|
||||
struct DHTSTRUCT {
|
||||
uint8_t pin;
|
||||
uint8_t type;
|
||||
char stype[12];
|
||||
uint32_t lastreadtime;
|
||||
uint8_t lastresult;
|
||||
float t = NAN;
|
||||
float h = NAN;
|
||||
} Dht[DHT_MAX_SENSORS];
|
||||
|
||||
bool DhtExpectPulse(uint32_t sensor, uint32_t level)
|
||||
{
|
||||
unsigned long timeout = micros() + 100;
|
||||
while (digitalRead(Dht[sensor].pin) != level) {
|
||||
if (micros() > timeout) { return false; }
|
||||
delayMicroseconds(1);
|
||||
}
|
||||
return true;
|
||||
}
|
||||
|
||||
bool DhtRead(uint32_t sensor)
|
||||
{
|
||||
dht_data[0] = dht_data[1] = dht_data[2] = dht_data[3] = dht_data[4] = 0;
|
||||
|
||||
if (!dht_dual_mode) {
|
||||
pinMode(Dht[sensor].pin, OUTPUT);
|
||||
digitalWrite(Dht[sensor].pin, LOW);
|
||||
} else {
|
||||
digitalWrite(dht_pin_out, LOW);
|
||||
}
|
||||
|
||||
switch (Dht[sensor].type) {
|
||||
case GPIO_DHT11: // DHT11
|
||||
delay(19); // minimum 18ms
|
||||
break;
|
||||
case GPIO_DHT22: // DHT21, DHT22, AM2301, AM2302, AM2321
|
||||
delay(2); // minimum 1ms
|
||||
break;
|
||||
case GPIO_SI7021: // iTead SI7021
|
||||
delayMicroseconds(500);
|
||||
break;
|
||||
}
|
||||
|
||||
if (!dht_dual_mode) {
|
||||
pinMode(Dht[sensor].pin, INPUT_PULLUP);
|
||||
} else {
|
||||
digitalWrite(dht_pin_out, HIGH);
|
||||
}
|
||||
|
||||
switch (Dht[sensor].type) {
|
||||
case GPIO_DHT11: // DHT11
|
||||
case GPIO_DHT22: // DHT21, DHT22, AM2301, AM2302, AM2321
|
||||
delayMicroseconds(50);
|
||||
break;
|
||||
case GPIO_SI7021: // iTead SI7021
|
||||
delayMicroseconds(20); // See: https://github.com/letscontrolit/ESPEasy/issues/1798
|
||||
break;
|
||||
}
|
||||
|
||||
uint32_t level = 9;
|
||||
noInterrupts();
|
||||
for (uint32_t i = 0; i < 3; i++) {
|
||||
level = i &1;
|
||||
if (!DhtExpectPulse(sensor, level)) { break; } // Expect LOW, HIGH, LOW
|
||||
level = 9;
|
||||
}
|
||||
if (9 == level) {
|
||||
int data = 0;
|
||||
for (uint32_t i = 0; i < 5; i++) {
|
||||
data = 0;
|
||||
for (uint32_t j = 0; j < 8; j++) {
|
||||
level = 1;
|
||||
if (!DhtExpectPulse(sensor, level)) { break; } // Expect HIGH
|
||||
|
||||
delayMicroseconds(35); // Was 30
|
||||
if (digitalRead(Dht[sensor].pin)) {
|
||||
data |= (1 << (7 - j));
|
||||
}
|
||||
|
||||
level = 0;
|
||||
if (!DhtExpectPulse(sensor, level)) { break; } // Expect LOW
|
||||
level = 9;
|
||||
}
|
||||
if (level < 2) { break; }
|
||||
|
||||
dht_data[i] = data;
|
||||
}
|
||||
}
|
||||
interrupts();
|
||||
if (level < 2) {
|
||||
AddLog_P2(LOG_LEVEL_DEBUG, PSTR(D_LOG_DHT D_TIMEOUT_WAITING_FOR " %s " D_PULSE), (0 == level) ? D_START_SIGNAL_LOW : D_START_SIGNAL_HIGH);
|
||||
return false;
|
||||
}
|
||||
|
||||
uint8_t checksum = (dht_data[0] + dht_data[1] + dht_data[2] + dht_data[3]) & 0xFF;
|
||||
if (dht_data[4] != checksum) {
|
||||
char hex_char[15];
|
||||
AddLog_P2(LOG_LEVEL_DEBUG, PSTR(D_LOG_DHT D_CHECKSUM_FAILURE " %s =? %02X"),
|
||||
ToHex_P(dht_data, 5, hex_char, sizeof(hex_char), ' '), checksum);
|
||||
return false;
|
||||
}
|
||||
|
||||
return true;
|
||||
}
|
||||
|
||||
void DhtReadTempHum(uint32_t sensor)
|
||||
{
|
||||
if ((NAN == Dht[sensor].h) || (Dht[sensor].lastresult > DHT_MAX_RETRY)) { // Reset after 8 misses
|
||||
Dht[sensor].t = NAN;
|
||||
Dht[sensor].h = NAN;
|
||||
}
|
||||
if (DhtRead(sensor)) {
|
||||
switch (Dht[sensor].type) {
|
||||
case GPIO_DHT11:
|
||||
Dht[sensor].h = dht_data[0];
|
||||
Dht[sensor].t = dht_data[2] + ((float)dht_data[3] * 0.1f); // Issue #3164
|
||||
break;
|
||||
case GPIO_DHT22:
|
||||
case GPIO_SI7021:
|
||||
Dht[sensor].h = ((dht_data[0] << 8) | dht_data[1]) * 0.1;
|
||||
Dht[sensor].t = (((dht_data[2] & 0x7F) << 8 ) | dht_data[3]) * 0.1;
|
||||
if (dht_data[2] & 0x80) {
|
||||
Dht[sensor].t *= -1;
|
||||
}
|
||||
break;
|
||||
}
|
||||
Dht[sensor].t = ConvertTemp(Dht[sensor].t);
|
||||
Dht[sensor].h = ConvertHumidity(Dht[sensor].h);
|
||||
Dht[sensor].lastresult = 0;
|
||||
} else {
|
||||
Dht[sensor].lastresult++;
|
||||
}
|
||||
}
|
||||
|
||||
/********************************************************************************************/
|
||||
|
||||
bool DhtPinState()
|
||||
{
|
||||
if ((XdrvMailbox.index >= GPIO_DHT11) && (XdrvMailbox.index <= GPIO_SI7021)) {
|
||||
if (dht_sensors < DHT_MAX_SENSORS) {
|
||||
Dht[dht_sensors].pin = XdrvMailbox.payload;
|
||||
Dht[dht_sensors].type = XdrvMailbox.index;
|
||||
dht_sensors++;
|
||||
XdrvMailbox.index = GPIO_DHT11;
|
||||
} else {
|
||||
XdrvMailbox.index = 0;
|
||||
}
|
||||
return true;
|
||||
}
|
||||
return false;
|
||||
}
|
||||
|
||||
void DhtInit(void)
|
||||
{
|
||||
if (dht_sensors) {
|
||||
if (pin[GPIO_DHT11_OUT] < 99) {
|
||||
dht_pin_out = pin[GPIO_DHT11_OUT];
|
||||
dht_dual_mode = true; // Dual pins mode as used by Shelly
|
||||
dht_sensors = 1; // We only support one sensor in pseudo mode
|
||||
pinMode(dht_pin_out, OUTPUT);
|
||||
}
|
||||
|
||||
for (uint32_t i = 0; i < dht_sensors; i++) {
|
||||
pinMode(Dht[i].pin, INPUT_PULLUP);
|
||||
Dht[i].lastreadtime = 0;
|
||||
Dht[i].lastresult = 0;
|
||||
GetTextIndexed(Dht[i].stype, sizeof(Dht[i].stype), Dht[i].type, kSensorNames);
|
||||
if (dht_sensors > 1) {
|
||||
snprintf_P(Dht[i].stype, sizeof(Dht[i].stype), PSTR("%s%c%02d"), Dht[i].stype, IndexSeparator(), Dht[i].pin);
|
||||
}
|
||||
}
|
||||
AddLog_P2(LOG_LEVEL_DEBUG, PSTR(D_LOG_DHT "(v4) " D_SENSORS_FOUND " %d"), dht_sensors);
|
||||
} else {
|
||||
dht_active = false;
|
||||
}
|
||||
}
|
||||
|
||||
void DhtEverySecond(void)
|
||||
{
|
||||
if (uptime &1) {
|
||||
} else {
|
||||
for (uint32_t i = 0; i < dht_sensors; i++) {
|
||||
// DHT11 and AM2301 25mS per sensor, SI7021 5mS per sensor
|
||||
DhtReadTempHum(i);
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
void DhtShow(bool json)
|
||||
{
|
||||
for (uint32_t i = 0; i < dht_sensors; i++) {
|
||||
char temperature[33];
|
||||
dtostrfd(Dht[i].t, Settings.flag2.temperature_resolution, temperature);
|
||||
char humidity[33];
|
||||
dtostrfd(Dht[i].h, Settings.flag2.humidity_resolution, humidity);
|
||||
|
||||
if (json) {
|
||||
ResponseAppend_P(JSON_SNS_TEMPHUM, Dht[i].stype, temperature, humidity);
|
||||
#ifdef USE_DOMOTICZ
|
||||
if ((0 == tele_period) && (0 == i)) {
|
||||
DomoticzTempHumSensor(temperature, humidity);
|
||||
}
|
||||
#endif // USE_DOMOTICZ
|
||||
#ifdef USE_KNX
|
||||
if ((0 == tele_period) && (0 == i)) {
|
||||
KnxSensor(KNX_TEMPERATURE, Dht[i].t);
|
||||
KnxSensor(KNX_HUMIDITY, Dht[i].h);
|
||||
}
|
||||
#endif // USE_KNX
|
||||
#ifdef USE_WEBSERVER
|
||||
} else {
|
||||
WSContentSend_PD(HTTP_SNS_TEMP, Dht[i].stype, temperature, TempUnit());
|
||||
WSContentSend_PD(HTTP_SNS_HUM, Dht[i].stype, humidity);
|
||||
#endif // USE_WEBSERVER
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
/*********************************************************************************************\
|
||||
* Interface
|
||||
\*********************************************************************************************/
|
||||
|
||||
bool Xsns06(uint8_t function)
|
||||
{
|
||||
bool result = false;
|
||||
|
||||
if (dht_active) {
|
||||
switch (function) {
|
||||
case FUNC_EVERY_SECOND:
|
||||
DhtEverySecond();
|
||||
break;
|
||||
case FUNC_JSON_APPEND:
|
||||
DhtShow(1);
|
||||
break;
|
||||
#ifdef USE_WEBSERVER
|
||||
case FUNC_WEB_SENSOR:
|
||||
DhtShow(0);
|
||||
break;
|
||||
#endif // USE_WEBSERVER
|
||||
case FUNC_INIT:
|
||||
DhtInit();
|
||||
break;
|
||||
case FUNC_PIN_STATE:
|
||||
result = DhtPinState();
|
||||
break;
|
||||
}
|
||||
}
|
||||
return result;
|
||||
}
|
||||
|
||||
#endif // USE_DHT
|
||||
Loading…
Reference in New Issue