5.5.1b
* Extent max number of WS2812 pixels from 256 to 512 (#667)
* Add OTA handling if server responds with no update available (#695)
* Removed undocumented command FlashMode (#696)
* Fix compile time error message due to increased message buffer size (#703)
5.5.0 20170730
* Reduce code space by removing the following commands as they are
replaced by SetOption alternatives:
* SaveState = SetOption0
* ButtonRestrict = SetOption1
* Units = SetOption2
* MQTT = SetOption3
* MQTTResponse = SetOption4
* TempUnit = SetOption8
* Smoothing WS2812 animation poll, invert fade speed and max allowed
wakeup time down to 3000 seconds
* Fix initial button press detection
* Add support for Sonoff RF Bridge 433 using command RfKey
* Fix regression from 5.0.7 by increasing message buffer size from 360
to 368 to accomodate 4 x DS18x20 sensors (#637)
* Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to
send either ON/OFF or TOGGLE (#642)
* Adjust HLW calibration limits to accomodate HuaFan device and add
commands HlwPSet, HlwUSet and HlwISet (#654)
5.3.0 20170715
* Major Hue rewrite which might introduce Alexa problems. If so,
initiate an issue
* Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control
to Hue
* Fix Sonoff Led Power, Dimmer and Color MQTT response (#176)
* Add commands Delay and Backlog to allow multiple commands at once
separated by ";" (#593)
* Use default flashmode DOUT to solve restart hangs on esp8285 chips
(#453, #598)
* Change Web console column width from 99 to 300 (#599)
5.2.4 20170703
* Removed flash mode update after selecting different module solving
esp8285 related problems
* Add device type flag to sonoff_template.ino
* Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led
5.2.2 20170625
* Add configuration SaveAddress to Status 1 and Information Page
* Change Sonoff Led Color conversion from AtoH to strtol
* Fix possible wrong uploads due to configuration overwrites (#542)
* Fix payload negative numbers (#547)
5.2.1 20170622
* Fix Restore Configuration in case of lower version
* Revert auto configuration upgrade allowing easy upgrade which was
removed in version 5.2.0
* Fix config auto upgrade from versions below version 4.1.1 (#530)
5.2.0 20170619
* Add command SetOption12 1 to disable newly released configuration
flash rotate to reduce flash wear
* Fix command CounterDebounce by removing test for active GPIO (#524)
* Add command SetOption33 1..250 to allow user configure POW
Max_Power_Retry count (#525)
5.1.7 20170616
* Prep removal of SetOptions alternatives
* Restore webpage upgrade error messages removed in 5.1.5
* Add hold button functionality to buttons 2 to 4
* Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds
to 10 seconds (#200)
* Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507)
* Changed webpage form actions from post to get and use relative path
url (#434, #522)
5.1.1 20170517
* Allow command FullTopic in group mode
* Prepare for more use of RTC memory
* Add independant WS2812 led string power control (#386, #390)
* Add command Counter<x> to control up to four GPIO falling edge
interrupt counters or timers (#459)
* Add command CounterType<x> to select between pulse counting or pulse
timing
* Add command CounterDebounce to select global counter debounce time in
mSec
5.1.0 20170513
* Fix Offline/Removal of retained topic when FullTopic is changed
* Add FullTopic to MQTT Configuration and Information web page
* Adde license model GPLv3 (#188)
5.0.7 20170511
* Fix possible exception 28 on empty command
* Add command SetOption0 as replacement for SaveState
* Add command SetOption1 as replacement for ButtonRestrict
* Add command SetOption2 as replacement for Units
* Add command SetOption4 as replacement for MqttResponse
* Add command SetOption8 as replacement for TempUnit
* Add command SetOption10 On|Off to select between Offline or Removing
previous retained topic (#417, #436)
5.0.6 20170510
* Remove hyphen in case of a single DHT sensor connecetd (#427)
* Add command MqttRetry <seconds> to change default MQTT reconnect retry
timer from minimal 10 seconds (#429)
5.0.2 20170503
* Reset SaveData, SaveState and MqttResponse to default values due to
rearranging settings
* Moved some settings flag area
* Add command TempUnit Celsius|Fahrenheit for selecting Celsius or
Fahrenheit (#347)
* Add command TempRes 0..3 for selecting Temperature Resolution (#347)
* Add command HumRes 0..3 for selecting Humidity Resolution (#347)
* Add command PressRes 0..3 for selecting Pressure Resolution (#347)
* Add command EnergyRes 0..5 for selecting Energy Resolution (#347)
* Add "TemperatureUnit":"C|F" to sensor JSON output (#347)
* Add support for up to three DHT type sensors each using a different
GPIO (#339, #404)
5.0.0 20170425
* Memory status message update
* Fix setting migration to better preserve settings during move (#382)
* Best practice is first doing a Backup Configuration before installing
version 5.0.0
* Reset save count after setting move
* Start using new linker script without SPIFFS
4.1.3 20170410
* Add user configuarble GPIO to module S20 Socket and Slampher
* Add support for Sonoff SC (#112)
* Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led
firmware (#122)
* Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions
due to power supply instabilities (#122)
* Add Access Point Mac Address to Status 11 and Telemetry (#329)
* Fix DS18B20 negative temperature readings (#334)
4.1.3 20170410
* Add user configuarble GPIO to module S20 Socket and Slampher
* Add support for Sonoff SC (#112)
* Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led
firmware (#122)
* Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions
due to power supply instabilities (#122)
* Add Access Point Mac Address to Status 11 and Telemetry (#329)
* Fix DS18B20 negative temperature readings (#334)
4.1.2 20170403
* Rename Unrecognised command to Unknown command
* Remove all command lists
* Remove command SmartConfig (superseded by WifiConfig)
* Fix boot loop when selecting module Sonoff 4CH or Sonoff Touch on non
ESP8285 hardware
* Add optional support for Toshiba and Mitsubishi HVAC IR control (needs
updated IRanother (#257)
* Add all configured switches to Domoticz Configuration web page (#305)
* Fix compile error when selecting WS2812 DMA (#313)
4.1.1 20170329
* Fix default Telemetry for command Prefix3
* Fix webserver Module parameters for disabled select
* Fix sensor status for enabled switches
* Remove Light as alternative for Power (save code space)
* Remove migration option from pre V3 (code cleanup)
* Remove unofficial SPIFFS support (code cleanup)
* Remove command list when unknown command is entered (save code space)
* Rename Status11 json from StatusPWR to unique StatusSTS
* Rename command Gateway to IPAddres2, Subnetmask to IPAddress3 and
DnsServer to IPAddress4 (save code space)
* Add Command MqttResponse to select either command or RESULT topic as
response (#258)
* Add command StateText1 to StateText3 to assign MQTT_STATUS_OFF,
MQTT_STATUS_ON and MQTT_CMND_TOGGLE respectively (#286)
* Remove restart after IPAddress changes (#292)
* Add support for MAX31850 in xsns_ds18x20.ino (#295)
* Fix possible uptime update misses (#302)
4.1.0 20170325
* Change static IP addresses in user_config.h from list (using commas)
to string (using dots)
* Unify display result of commands Modules, Module and Gpios
* Rewrite Module selection web page to bring size down from 18651 to
4319 bytes (!) (#234, #240)
* Add basic support for (Lixada) H801 RGBWW controller (#252)
* Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and
PUB_PREFIX2 respectively (#255)
* Add static ip addresses to flash (#262)
* Add commands IpAddress, Gateway, Subnetmask and DnsServer to select
static ip addresses (#273)
4.0.8 20170321
* Fix entering non-numeric webpassword
* Force selection between TLS or Webserver due to memory restraint
(#240)
* Allow entering empty string using "0" for selected commands (#242)
* Fix exception when posting commands to web console containing % (#250)
4.0.7 20170319
* Increased Sonoff Led PWM frequency from 432 to 1000
* Fix possible watch dog reboot after changing module type on web page
* Fix reporting of GPIO usage from web page
* Fix Sonoff Led blank during firmware upgrade
* Fix Sonoff Led flicker and possible flash corruption by using latest
Arduino-esp8266 versions
* of pwm core files included in sonoff library (#211)
* Add PWM output control with commands PWM1 to PWM5 using user
selectable GPIOs (#211)
* Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal
(1000) and HlwICal (2500) (#223)
* Add Switch state to sensor status (#227, #233)
* Add user configuarble GPIO to module Sonoff Touch (#228)
* Add define WEB_PORT to user_config.h to change default web server port
from 80 (#232)
* Fix failed Ota Firmware upgrade started from Web page (#235)
4.0.6 20170316
* Fix to better find device by Wifi hostname
* Fix compile error when some I2C devices are disabled
* Add (experimental) support for SHT1X emulating I2C (#97)
* Add ADC to ElectroDragon (#203)
* Add support for Sonoff Dev (#206)
4.0.3 20170309
* Renamed Module NodeMCU to WeMos D1 mini
* Add GPIO1 as user option to some modules
* Add Buttons, Relays and Leds to user configurable options (#159)
* Add description on Module parameters web page to some well known GPIOs
(#107, #171)
4.0.2 20170308
* Restore correct seriallog level after Serial logging was disabled
* Add simple dimmer slider to Sonoff Led web page
* Reduced root webpage size by 31%
* Expand Status 2 with Build date/time and core version
* Fix webserver redirection when not in WifiManager mode (#156)
* Add command ButtonRestrict On/Off to restrict access to button hold
and button multi press options above 2 (#161)
* Fix DS18S20 negative temperature readings (#165)
* Fix crlf compilation error due to bad syntax (#144, #167)
4.0.1 20170305
* Fix char default sizes and set MESSZ to 360 (#143)
* Fix SerialLog setting status
* Disable syslog when emulation is active
* Add DS18B20 web page display refresh
4.0.0 20170303
* Add define to remove config migration code for versions below 3.0 (See
Wiki-Upgrade-Migration path)
* Free memory by switching from String to char[]
* Raised Sonoff Led PWM frequency from 200Hz to 432Hz in search of
stability (hardware watchdog timeouts) (#122)
* Increase message size and suggested minimum MQTT_MAX_PACKET_SIZE to
512 (#114, #124)
* Remove runtime warning message regarding MQTT_MAX_PACKET_SIZE too
small as it is now moved to compile time (#124)
* Fix possible panics with web console and http commands while UDP
syslog is active (#127)
* Add optional static IP address (#129)
* Add define ENERGY_RESOLUTION in user_config.h to allow user control
over precision (#136)
3.9.22 20170228
* Update web console
* Fix Status 4 JSON message
* Add Exception info during restart if available
* Add osWatch service to detect loop hangs that might happen during
(OTA) upgrades
* Add WiOn support for relay and switch only (#82, #102)
* Allow for user specified relay count up to four in sonoff_template.h
(#109)
* Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021
(#118)
* Add NodeMCU or Wemos configuration option (#119)
3.9.21 20170224
* Add ajax to web root page and web console (#79)
* Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84,
#88)
* Fix MQTT upgrade when webserver is active
3.9.18 20170218
* Fix ledstate 0 to turn off led
* Fix Sonoff Led dimmer range (#16)
* Change Sonoff Led command Dimmer to act on both cold and warm color
* Add Sonoff Led command Color CCWW where CCWW are hexadecimal values
fro 00 - FF
* Reduce Sonoff Led flickering by disabling interrupts during flash save
and disabling
* Led during OTA upgrade and Web upload (#16)
3.9.17 20170217
* Fix possible ArduinoJSON related memory fragmentation
* Changed console logging using less memory
* Add GPIO04 as user selectable for Sonoff Dual (#75)
3.9.16 20170214
* Update latching relay handler
* Add support for IR led using IRremoteESP8266 library (#59)
* Add Hue argument passing using ArduinoJSON library (#59)
3.9.14 20170211
* Add False and True as alternatives for 0/Off and 1/On (#49)
* Fix Status10 JSON format (#52)
* Fix DS18x20 using OneWire library (#53)
3.9.13 20170210
* Add FlashChipSize to Status 4
* Removed redundant DHT2 option and code
* Add Sonoff SV GPIO pin 05 configuration (#40)
* Add configuration file backup and restore via web page
* Fix latency due to light_sleep mode even if sleep was set to zero
(#50)
3.9.12 20170208
* Fix compile error when webserver is disabled (#30)
* Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT
during OTA upload
* Fix hostname issues by not allowing user entry of string formatting
and removing from user_config.h (#36)
3.9.11 20170204
* Fix command I2Cscan
* Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic
* Make all TELEMETRY, STATUS and COMMAND message topics unique (#4)
* Advertise command topic to be used by iobroker (#299)
* Fix butten (non)detection if no GPIO_KEY1 is defined (#13)
* Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars
(#18)
* Update web page with Build Date/Time, Emulation and mDNS Discovery and
Advertise information (#21)
Theo Arends