5.2.4 20170703
* Removed flash mode update after selecting different module solving
esp8285 related problems
* Add device type flag to sonoff_template.ino
* Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led (#567)
5.2.4 20170703
* Removed flash mode update after selecting different module solving
esp8285 related problems
* Add device type flag to sonoff_template.ino
* Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led
5.2.3 20170630
* Change Sonoff Led color conversion code
* Fix SetOption12 handling
* Simplify auto configuration upgrade
* Add option Upgrade <version_number> to only upgrade to any higher
version (Old PR #213)
* Change FallbackTopic to cmnd/<MQTTClient>/<command> <parameter>
bypassing FullTopic and Prefix (#538)
5.2.2 20170625
* Add configuration SaveAddress to Status 1 and Information Page
* Change Sonoff Led Color conversion from AtoH to strtol
* Fix possible wrong uploads due to configuration overwrites (#542)
* Fix payload negative numbers (#547)
5.2.2 20170625
* Add configuration SaveAddress to Status 1 and Information Page
* Change Sonoff Led Color conversion from AtoH to strtol
* Fix possible wrong uploads due to configuration overwrites (#542)
* Fix payload negative numbers (#547)
5.2.1 20170622
* Fix Restore Configuration in case of lower version
* Revert auto configuration upgrade allowing easy upgrade which was
removed in version 5.2.0
* Fix config auto upgrade from versions below version 4.1.1 (#530)
5.2.0 20170619
* Add command SetOption12 1 to disable newly released configuration
flash rotate to reduce flash wear
* Fix command CounterDebounce by removing test for active GPIO (#524)
* Add command SetOption33 1..250 to allow user configure POW
Max_Power_Retry count (#525)
5.1.7 20170616
* Prep removal of SetOptions alternatives
* Restore webpage upgrade error messages removed in 5.1.5
* Add hold button functionality to buttons 2 to 4
* Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds
to 10 seconds (#200)
* Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507)
* Changed webpage form actions from post to get and use relative path
url (#434, #522)
5.1.6 20170606
* Shrink code
* Removed online configuration of Domoticz In and Domoticz Out MQTT
strings
* Removed commands DomoticzInTopic and DomoticzOutTopic
* Add define KEY_HOLD_TIME to configure button hold threshold before
sending MQTT Hold message
* Add command StateText4 to configure button MQTT Hold text (=
MQTT_CMND_HOLD)
* Add command SetOption11 0|1 to swap pushbutton single and double press
functionality (#200)
* Add command SwitchMode<x> 5 (PUSHBUTTONHOLD) and 6
(PUSHBUTTONHOLD_INV) (#489)
5.1.4 20170601
* Removed pre-compiled versions from repository as they are available
within the release
* Changed HUE Device type to color supporting version (#464)
* Fix compile error when BE_MINIMAL is selected (#467, #476)
* Add multiple compiled versions to release using updated Travis script
and platformio.ini (#467)
5.1.1 20170517
* Allow command FullTopic in group mode
* Prepare for more use of RTC memory
* Add independant WS2812 led string power control (#386, #390)
* Add command Counter<x> to control up to four GPIO falling edge
interrupt counters or timers (#459)
* Add command CounterType<x> to select between pulse counting or pulse
timing
* Add command CounterDebounce to select global counter debounce time in
mSec
5.1.0 20170513
* Fix Offline/Removal of retained topic when FullTopic is changed
* Add FullTopic to MQTT Configuration and Information web pages
* Add license model GPLv3 (#188)
5.1.0 20170513
* Fix Offline/Removal of retained topic when FullTopic is changed
* Add FullTopic to MQTT Configuration and Information web pages
* Add license model GPLv3 (#188)
5.1.0 20170513
* Fix Offline/Removal of retained topic when FullTopic is changed
* Add FullTopic to MQTT Configuration and Information web page
* Add license model GPLv3 (#188)
5.1.0 20170513
* Fix Offline/Removal of retained topic when FullTopic is changed
* Add FullTopic to MQTT Configuration and Information web page
* Adde license model GPLv3 (#188)
5.0.7 20170511
* Fix possible exception 28 on empty command
* Add command SetOption0 as replacement for SaveState
* Add command SetOption1 as replacement for ButtonRestrict
* Add command SetOption2 as replacement for Units
* Add command SetOption4 as replacement for MqttResponse
* Add command SetOption8 as replacement for TempUnit
* Add command SetOption10 On|Off to select between Offline or Removing
previous retained topic (#417, #436)
5.0.6 20170510
* Remove hyphen in case of a single DHT sensor connecetd (#427)
* Add command MqttRetry <seconds> to change default MQTT reconnect retry
timer from minimal 10 seconds (#429)
5.0.5 20170508
* Add command FullTopic with tokens %topic% (replaced by command Topic
value) and
* %prefix% (replaced by command Prefix<x> values) for more flexible
topic definitions (#244)
* See wiki > MQTT Features
https://github.com/arendst/Sonoff-Tasmota/wiki/MQTT-Features for more
information
5.0.4 20170505
* Add Sonoff Pow Energy Total up to 40 MWh
* Add command EnergyReset 1|2|3 to reset Energy counters (#406)
* Fix Domoticz Energy logging (#411)
* Add command PowerOnState 4 to keep relay always on and disabling all
power control (#418)
5.0.3 20170504
* Add command SensorRetain on|off to enable retaining of mqtt message
tele/sonoff/SENSOR (#74)
* Change WifiConfig timeout from 60 seconds to 180 seconds (#212)
* Change Sonoff Touch command Ledstate functionality by turning led on
if power is off (#214)
* Add 4 seconds delay after power on before enabling button to
workaround Wemos D1 mini RTS circuit (#380)
5.0.2 20170503
* Reset SaveData, SaveState and MqttResponse to default values due to
rearranging settings
* Moved some settings to flag area
* Add command TempUnit Celsius|Fahrenheit for selecting Celsius or
Fahrenheit (#347)
* Add command TempRes 0..3 for selecting Temperature Resolution (#347)
* Add command HumRes 0..3 for selecting Humidity Resolution (#347)
* Add command PressRes 0..3 for selecting Pressure Resolution (#347)
* Add command EnergyRes 0..5 for selecting Energy Resolution (#347)
* Add "TempUnit":"C|F" to sensor JSON output (#347)
* Add support for up to three DHT type sensors each using a different
GPIO (#339, #404)
5.0.2 20170503
* Reset SaveData, SaveState and MqttResponse to default values due to
rearranging settings
* Moved some settings flag area
* Add command TempUnit Celsius|Fahrenheit for selecting Celsius or
Fahrenheit (#347)
* Add command TempRes 0..3 for selecting Temperature Resolution (#347)
* Add command HumRes 0..3 for selecting Humidity Resolution (#347)
* Add command PressRes 0..3 for selecting Pressure Resolution (#347)
* Add command EnergyRes 0..5 for selecting Energy Resolution (#347)
* Add "TemperatureUnit":"C|F" to sensor JSON output (#347)
* Add support for up to three DHT type sensors each using a different
GPIO (#339, #404)
5.0.1 20170429
* Adjust Sonoff SC messages to prepare for display feature
* Move static data from RAM to Flash
* Fix PowerOnState for some devices not reporting "Power on" state
(#284, #380, #383)
5.0.0 20170425
* Memory status message update
* Fix setting migration to better preserve settings during move (#382)
* Best practice is first doing a Backup Configuration before installing
version 5.0.0
* Reset save count after setting move
* Start using new linker script without SPIFFS
4.1.3 20170410
* Add user configuarble GPIO to module S20 Socket and Slampher
* Add support for Sonoff SC (#112)
* Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led
firmware (#122)
* Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions
due to power supply instabilities (#122)
* Add Access Point Mac Address to Status 11 and Telemetry (#329)
* Fix DS18B20 negative temperature readings (#334)
4.1.3 20170410
* Add user configuarble GPIO to module S20 Socket and Slampher
* Add support for Sonoff SC (#112)
* Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led
firmware (#122)
* Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions
due to power supply instabilities (#122)
* Add Access Point Mac Address to Status 11 and Telemetry (#329)
* Fix DS18B20 negative temperature readings (#334)
Theo Arends
Thomas Dietrich