mirrors
/
Tasmota
mirror of https://github.com/arendst/Tasmota.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
Tasmota/tasmota/tasmota_xdrv_driver/xdrv_75_dali.ino

1393 lines
62 KiB
C++
Raw Permalink Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/*
xdrv_75_dali.ino - DALI support for Tasmota
Copyright (C) 2022 Andrei Kazmirtsuk aka eeak and Theo Arends
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
--------------------------------------------------------------------------------------------
Version yyyymmdd Action Description
--------------------------------------------------------------------------------------------
1.1.0.1 20241101 update - Enable DALI if another light is already claimed
1.1.0.0 20241031 update - Add GUI sliders with feedback when `DaliLight 0`
- Add command `DaliGroupSliders 0..16` to show GUI sliders
1.0.0.2 20241025 update - Fix GPIO detection
- Fix ESP32(C3) transmit stability by disabling interrupts
1.0.0.1 20241024 update - Change from signal invert defines to GPIO config DALI RX_i/DALI TX_i
- Fix inverted DALI signal support
- Experimental support for Shelly DALI Dimmer Gen3
1.0.0.0 20241022 update - Refactor commission
- Add receive collision detection
0.1.0.8 20241019 update - Rename command `DaliCommission` to `DaliScan`
- Rename command `DaliWeb` to `DaliLight`
- Add command `DaliGear` to set max found gear to speed up scan response
0.1.0.7 20241017 update - Add command `DaliCommission 1|2` assigning short addresses
- Add command `DaliTarget 0, 1..64, 101..116` to select light control address
- Add command `DaliGroup1..16 +<devices>|-<devices>` to add/remove devices from group
- Extend commands `DaliPower` and `DaliDimmer` with index to control short address or group
- Remove non-functional MQTT interface
0.1.0.6 20241014 update - Fix received light command loop
- Add send collision detection
0.1.0.5 20241014 update - Add command `DaliSend [repeat]<address>,<command>`
- Add command `DaliQuery [repeat]<address>,<command>`
- Send frame twice (repeat) for DALI defined commands
- Add support for receiving backward frame
0.1.0.4 20241013 update - Fix intermittent bad send timing
0.1.0.3 20241010 update - Change DaliDimmer range from 0..254 to 0..100
- Add command `DaliWeb 0|1` to enable persistent Web light controls
0.1.0.2 20241008 update - Better receive error detection
0.1.0.1 20241007 update - To stablizie communication send DALI datagram twice like Busch-Jaeger does
- Change DaliPower 0..2 to act like Tasmota Power (Off, On, Toggle)
- Keep last Dimmer value as default power on
0.1.0.0 20241006 rewrite - Add support for ESP8266
- Fix decoding of received DALI data
- Refactor command `DaliPower 0..254` controlling Broadcast devices
- Add command `DaliDimmer 0..254` controlling Broadcast devices
0.0.0.1 20221027 publish - Initial version
*/
#ifdef USE_DALI
/*********************************************************************************************\
* DALI support for Tasmota
*
* Available commands:
* <byte1> or <byte3> = 0..255 or 0x00..0xFF + 256/0x100 for optional repeat (send twice)
* <byte2> or <byte4> = 0..255 or 0x00..0xFF - Both decimal and hexadecimal is supported
* <broadcast> = 0 - DALI default
* <device> = 1..64 - DALI short address + 1
* <group> = 101..116 - DALI group + 101
* DaliSend <byte1>,<byte2> - Execute DALI code and do not expect a DALI backward frame
* DaliSend <0xA3>,<byte2>,<byte3>,<byte4> - Set DALI parameter using DTR0 and do not expect a DALI backward frame
* DaliQuery <byte1>,<byte2> - Execute DALI code and report result (DALI backward frame)
* DaliScan 1|2 - Reset (0) or (1)/and commission device short addresses
* DaliGear 1..64 - Set max short address to speed up scanning - default 64
* DaliGroup<1..16> [+]|-<device>,<device>... - Add(+) or Remove(-) devices to/from group
* DaliPower<broadcast>|<device>|<group> 0..254 - Control power (0 = Off, 1 = Last dimmer, 2 = Toggle, 3..254 = absolute light brightness)
* DaliDimmer<broadcast>|<device>|<group> 0..100 - Control dimmer (0 = Off, 1..100 = precentage of brightness)
* DaliLight 0|1 - Enable Tasmota light control for DaliTarget device - default 1
* DaliTarget <broadcast>|<device>|<group> - Set Tasmota light control device (0, 1..64, 101..116) - default 0
*
* DALI background information
* Address type Address byte
* ------------------ --------------------
* Broadcast address 1111111S
* 64 short address 0AAAAAAS
* 16 group address 100AAAAS
* Special command 101CCCC1 to 110CCCC1
* A = Address bit, S = 0 Direct Arc Power control, S = 1 Command, C = Special command
*
* Shelly DALI Dimmer Gen3 (ESP32C3-8M) - GPIO3 controls DALI power. In following template it is always ON. Max output is 16V/10mA (= 5 DALI gear)
* Template {"NAME":"Shelly DALI Dimmer Gen3","GPIO":[34,4736,0,3840,11360,11392,128,129,0,1,576,0,0,0,0,0,0,0,0,1,1,1],"FLAG":0,"BASE":1}
* AdcGpio1 10000,10000,4000 <- Temperature parameters
* Backlog ButtonTopic 0; SetOption1 1; SetOption11 0; SetOption32 20; DimmerStep 5; LedTable 0
* rule1 on button1#state=2 do dimmer + endon on button2#state=2 do dimmer - endon on button1#state=3 do power 2 endon on button2#state=3 do power 2 endon
\*********************************************************************************************/
#define XDRV_75 75
#ifndef DALI_INIT_STATE
#define DALI_INIT_STATE 50 // DALI init dimmer state 50/254
#endif
#ifndef DALI_INIT_FADE
#define DALI_INIT_FADE 1 // Fade between light states in number of seconds
#endif
#ifndef DALI_TIMEOUT
#define DALI_TIMEOUT 50 // DALI backward frame receive timeout (ms)
#endif
//#define DALI_DEBUG
#ifndef DALI_DEBUG_PIN
#define DALI_DEBUG_PIN 4 // Debug GPIO
#endif
// Control commands - Send as second byte without repeat
#define DALI_OFF 0x0000 // 0 - Turns off lighting.
#define DALI_UP 0x0001 // 1 - Increases the lighting control level for 200 ms according to the Fade rate.
#define DALI_DOWN 0x0002 // 2 - Decreases the lighting control level for 200 ms according to the Fade rate.
#define DALI_STEP_UP 0x0003 // 3 - Increments the lighting control level (without fade).
#define DALI_STEP_DOWN 0x0004 // 4 - Decrements the lighting control level (without fade).
#define DALI_RECALL_MAX_LEVEL 0x0005 // 5 - Maximizes the lighting control level (without fade).
#define DALI_RECALL_MIN_LEVEL 0x0006 // 6 - Minimizes the lighting control level (without fade)
#define DALI_STEP_DOWN_AND_OFF 0x0007 // 7 - Decrements the lighting control level and turns off lighting if the level is at the minimum (without fade).
#define DALI_ON_AND_STEP_UP 0x0008 // 8 - Increments the lighting control level and turns on lighting if lighting is off (with fade).
#define DALI_ENABLE_DAPC_SEQUENCE 0x0009 // 9 - It shows the repeat start of the DAPC command.
#define DALI_GO_TO_LAST_ACTIVE_LEVEL 0x000A // 10 - DALI-2 Adjusts the lighting control level to the last light control level according to the Fade time.
#define DALI_RESERVED11 0x000B // 11 - [Reserved]
#define DALI_RESERVED15 0x000F // 15 - [Reserved]
#define DALI_GO_TO_SCENE0 0x0010 // 16 - Adjusts the lighting control level for Scene XXXX according to the fade time.
#define DALI_GO_TO_SCENE15 0x001F // 31 - Adjusts the lighting control level for Scene XXXX according to the fade time.
// Configuration commands - Send as second byte with repeat
#define DALI_RESET 0x0020 // 32 - Makes a slave an RESET state.
#define DALI_STORE_ACTUAL_LEVEL_IN_THE_DTR0 0x0021 // 33 - Saves the current lighting control level to the DTR (DTR0).
#define DALI_SAVE_PERSISTENT_VARIABLES 0x0022 // 34 - DALI-2 Saves a variable in nonvolatile memory (NVM).
#define DALI_SET_OPERATING_MODE 0x0023 // 35 - DALI-2 Sets data of DTR0 as an operating mode.
#define DALI_RESET_MEMORY_BANK 0x0024 // 36 - DALI-2 Changes to the reset value the specified memory bank in DTR0.
#define DALI_IDENTIFY_DEVICE 0x0025 // 37 - DALI-2 Starts the identification state of the device.
#define DALI_RESERVED38 0x0026 // 38 - [Reserved]
#define DALI_RESERVED41 0x0029 // 41 - [Reserved]
#define DALI_SET_MAX_LEVEL 0x002A // 42 - Specifies the DTR data as the maximum lighting control level.
#define DALI_SET_MIN_LEVEL 0x002B // 43 - Specifies the DTR data as the minimum lighting control level.
#define DALI_SET_SYSTEM_FAILURE_LEVEL 0x002C // 44 - Specifies the DTR data as the "FAILURELEVEL".
#define DALI_SET_POWER_ON_LEVEL 0x002D // 45 - Specifies the DTR data as the "POWER ONLEVEL".
#define DALI_SET_FADE_TIME 0x002E // 46 - Specifies the DTR data as the Fade time.
#define DALI_SET_FADE_RATE 0x002F // 47 - Specifies the DTR data as the Fade rate.
#define DALI_SET_EXTENDED_FADE_TIME 0x0030 // 48 - DALI-2 Specifies the DTR data as the Extended Fade Time.
#define DALI_RESERVED49 0x0031 // 49 - [Reserved]
#define DALI_RESERVED63 0x003F // 63 - [Reserved]
#define DALI_SET_SCENE0 0x0040 // 64 - Specifies the DTR data as Scene XXXX.
#define DALI_SET_SCENE15 0x004F // 79 - Specifies the DTR data as Scene XXXX.
#define DALI_REMOVE_FROM_SCENE0 0x0050 // 80 - Deletes the Scene XXXX setting. (Specifies 1111 1111 for the scene register.)
#define DALI_REMOVE_FROM_SCENE15 0x005F // 95 - Deletes the Scene XXXX setting. (Specifies 1111 1111 for the scene register.)
#define DALI_ADD_TO_GROUP0 0x0060 // 96 - Adds the slave to Group XXXX.
#define DALI_ADD_TO_GROUP15 0x006F // 111 - Adds the slave to Group XXXX.
#define DALI_REMOVE_FROM_GROUP0 0x0070 // 112 - Deletes the slave from Group XXXX.
#define DALI_REMOVE_FROM_GROUP15 0x007F // 127 - Deletes the slave from Group XXXX.
#define DALI_SET_SHORT_ADDRESS 0x0080 // 128 - Specifies the DTR data as a Short Address.
#define DALI_ENABLE_WRITE_MEMORY 0x0081 // 129 - Allows writing of the memory bank.
#define DALI_RESERVED130 0x0082 // 130 - [Reserved]
#define DALI_RESERVED143 0x008F // 143 - [Reserved]
// Query commands - Send as second byte
#define DALI_QUERY_STATUS 0x0090 // 144 - Returns "STATUS INFORMATION"
#define DALI_QUERY_CONTROL_GEAR_PRESENT 0x0091 // 145 - Is there a slave that can communicate?
#define DALI_QUERY_LAMP_FAILURE 0x0092 // 146 - Is there a lamp problem?
#define DALI_QUERY_LAMP_POWER_ON 0x0093 // 147 - Is a lamp on?
#define DALI_QUERY_LIMIT_ERROR 0x0094 // 148 - Is the specified lighting control level out of the range from the minimum to the maximum values?
#define DALI_QUERY_RESET_STATE 0x0095 // 149 - Is the slave in 'RESET STATE'?
#define DALI_QUERY_MISSING_SHORT_ADDRESS 0x0096 // 150 - Does the slave not have a short address?
#define DALI_QUERY_VERSION_NUMBER 0x0097 // 151 - What is the corresponding IEC standard number?
#define DALI_QUERY_CONTENT_DTR0 0x0098 // 152 - What is the DTR content?
#define DALI_QUERY_DEVICE_TYPE 0x0099 // 153 - What is the device type? (fluorescent lamp:0000 0000) (IEC62386-207 is 6 fixed)
#define DALI_QUERY_PHYSICAL_MINIMUM_LEVEL 0x009A // 154 - What is the minimum lighting control level specified by the hardware?
#define DALI_QUERY_POWER_FAILURE 0x009B // 155 - Has the slave operated without the execution of reset-command or the adjustment of the lighting control level?
#define DALI_QUERY_CONTENT_DTR1 0x009C // 156 - What is the DTR1 content?
#define DALI_QUERY_CONTENT_DTR2 0x009D // 157 - What is the DTR2 content?
#define DALI_QUERY_OPERATING_MODE 0x009E // 158 - DALI-2 What is the Operating Mode?
#define DALI_QUERY_LIGHT_SOURCE_TYPE 0x009F // 159 - DALI-2 What is the Light source type?
#define DALI_QUERY_ACTUAL_LEVEL 0x00A0 // 160 - What is the "ACTUAL LEVEL" (the current lighting control level)?
#define DALI_QUERY_MAX_LEVEL 0x00A1 // 161 - What is the maximum lighting control level?
#define DALI_QUERY_MIN_LEVEL 0x00A2 // 162 - What is the minimum lighting control level?
#define DALI_QUERY_POWER_ON_LEVEL 0x00A3 // 163 - What is the "POWER ON LEVEL" (the lighting control level when the power is turned on)?
#define DALI_QUERY_SYSTEM_FAILURE_LEVEL 0x00A4 // 164 - What is the "SYSTEM FAILURE LEVEL" (the lighting control level when a failure occurs)?
#define DALI_QUERY_FADE_TIME_FADE_RATE 0x00A5 // 165 - What are the Fade time and Fade rate?
#define DALI_QUERY_MANUFACTURER_SPECIFIC_MODE 0x00A6 // 166 - DALI-2 What is the Specific Mode?
#define DALI_QUERY_NEXT_DEVICE_TYPE 0x00A7 // 167 - DALI-2 What is the next Device Type?
#define DALI_QUERY_EXTENDED_FADE_TIME 0x00A8 // 168 - DALI-2 What is the Extended Fade Time?
#define DALI_QUERY_CONTROL_GEAR_FAILURE 0x00A9 // 169 - DALI-2 Does a slave have the abnormality?
#define DALI_RESERVED170 0x00AA // 170 - [Reserved]
#define DALI_RESERVED175 0x00AF // 175 - [Reserved]
#define DALI_QUERY_SCENE0_LEVEL 0x00B0 // 176 - What is the lighting control level for SCENE XXXX?
#define DALI_QUERY_GROUPS_0_7 0x00C0 // 192 - Does the slave belong to a group among groups 0 to 7? (Each bit corresponds to a group.)
#define DALI_QUERY_GROUPS_8_15 0x00C1 // 193 - Does the slave belong to a group among groups 8 to 15? (Each bit corresponds to a group.)
#define DALI_QUERY_RANDOM_ADDRESS_H 0x00C2 // 194 - What are the higher 8 bits of the random address?
#define DALI_QUERY_RANDOM_ADDRESS_M 0x00C3 // 195 - What are the middle 8 bits of the random address?
#define DALI_QUERY_RANDOM_ADDRESS_L 0x00C4 // 196 - What are the lower 8 bits of the random address?
#define DALI_READ_MEMORY_LOCATION 0x00C5 // 197 - What is the memory location content?
#define DALI_RESERVED198 0x00C6 // 198 - [Reserved]
#define DALI_RESERVED223 0x00DF // 223 - [Reserved]
// Application extended configuration commands - Send as second byte
#define DALI_REFERENCE_SYSTEM_POWER 0x00E0 // 224 - IEC62386-207 Starts power measurement.
#define DALI_ENABLE_CURRENT_PROTECTOR 0x00E1 // 225 - IEC62386-207 Enables the current protection.
#define DALI_DISABLE_CURRENT_PROTECTOR 0x00E2 // 226 - IEC62386-207 Disables the current protection.
#define DALI_SELECT_DIMMING_CURVE 0x00E3 // 227 - IEC62386-207 Selects Dimming curve.
#define DALI_STORE_DTR_AS_FAST_FADE_TIME 0x00E4 // 228 - IEC62386-207 Sets the DTR of the data as Fast Fade Time.
#define DALI_RESERVED229 0x00E5 // 229 - [Reserved]
#define DALI_RESERVED236 0x00EC // 236 - [Reserved]
// Application extended query commands - Send as second byte
#define DALI_QUERY_GEAR_TYPE 0x00ED // 237 - IEC62386-207 Returns ‘GEAR TYPE’
#define DALI_QUERY_DIMMING_CURVE 0x00EE // 238 - IEC62386-207 Returns ’Dimming curve’in use
#define DALI_QUERY_POSSIBLE_OPERATING_MODE 0x00EF // 239 - IEC62386-207 Returns ‘POSSIBLE OPERATING MODE’
#define DALI_QUERY_FEATURES 0x00F0 // 240 - IEC62386-207 Returns ‘FEATURES’
#define DALI_QUERY_FAILURE_STATUS 0x00F1 // 241 - IEC62386-207 Returns ‘FAILURE STATUS’
#define DALI_QUERY_SHORT_CIRCUIT 0x00F2 // 242 - IEC62386-207 Returns bit0 short circuit of ‘FAILURE STATUS’
#define DALI_QUERY_OPEN_CIRCUIT 0x00F3 // 243 - IEC62386-207 Returns bit1 open circuit of ‘FAILURE STATUS’
#define DALI_QUERY_LOAD_DECREASE 0x00F4 // 244 - IEC62386-207 Returns bit2 load decrease of ‘FAILURE STATUS’
#define DALI_QUERY_LOAD_INDREASE 0x00F5 // 245 - IEC62386-207 Returns bit3 load increase of‘FAILURE STATUS’
#define DALI_QUERY_CURRENT_PROTECTOR_ACTIVE 0x00F6 // 246 - IEC62386-207 Returns bit4 current protector active of ‘FAILURE STATUS’
#define DALI_QUERY_THERMAL_SHUTDOWN 0x00F7 // 247 - IEC62386-207 Returns bit5 thermal shut down of ‘FAILURE STATUS’
#define DALI_QUERY_THERMAL_OVERLOAD 0x00F8 // 248 - IEC62386-207 Returns bit6 thermal overload with light level reduction of ‘FAILURE STATUS’
#define DALI_QUERY_REFARENCE_RUNNING 0x00F9 // 249 - IEC62386-207 Returns whetherReference System Power is in operation.
#define DALI_QUERY_REFERENCE_MEASURMENT_FAILED 0x00FA // 250 - IEC62386-207 Returns bit7 reference measurement failed of ‘FAILURE STATUS’
#define DALI_QUERY_CURRENT_PROTECTOR_ENABLE 0x00FB // 251 - IEC62386-207 Returns state of Curent protector
#define DALI_QUERY_OPERATING_MODE2 0x00FC // 252 - IEC62386-207 Returns ‘OPERATING MODE’
#define DALI_QUERY_FAST_FADE_TIME 0x00FD // 253 - IEC62386-207 Returns set Fast fade time.
#define DALI_QUERY_MIN_FAST_FADE_TIME 0x00FE // 254 - IEC62386-207 Returns set Minimum fast fade time
#define DALI_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - IEC62386-207 The version number of the extended support? IEC62386-207: 1, Other: NO(no response)
// Address types - Send as first byte
#define DALI_SHORT_ADDRESS0 0x0000 // 0b00000000 0 - First short address
#define DALI_SHORT_ADDRESS1 0x0002 // 0b00000010 1 - Next short address
#define DALI_SHORT_ADDRESS63 0x007E // 0b01111110 63 - Last short address
#define DALI_GROUP_ADDRESS0 0x0080 // 0b10000000 0 - First group address
#define DALI_GROUP_ADDRESS1 0x0082 // 0b10000010 1 - Next group address
#define DALI_GROUP_ADDRESS15 0x009E // 0b10011110 15 - Last group address
// Special commands - Send as first byte
#define DALI_TERMINATE 0x00A1 // 256 - Releases the INITIALISE state.
#define DALI_DATA_TRANSFER_REGISTER0 0x00A3 // 257 - Stores the data XXXX XXXX to the DTR(DTR0).
#define DALI_INITIALISE 0x01A5 // 258 REPEAT - Sets the slave to the INITIALISE status for15 minutes. Commands 259 to 270 are enabled only for a slave in this status.
#define DALI_RANDOMISE 0x01A7 // 259 REPEAT - Generates a random address.
#define DALI_COMPARE 0x00A9 // 260 - Is the random address smaller or equal to the search address?
#define DALI_WITHDRAW 0x00AB // 261 - Excludes slaves for which the random address and search address match from the Compare process.
#define DALI_RESERVED262 0x00AD // 262 - [Reserved]
#define DALI_PING 0x00AF // 263 - DALI-2 Ignores in the slave.
#define DALI_SEARCHADDRH 0x00B1 // 264 - Specifies the higher 8 bits of the search address.
#define DALI_SEARCHADDRM 0x00B3 // 265 - Specifies the middle 8 bits of the search address.
#define DALI_SEARCHADDRL 0x00B5 // 266 - Specifies the lower 8 bits of the search address.
#define DALI_PROGRAM_SHORT_ADDRESS 0x00B7 // 267 - The slave shall store the received 6-bit address (AAA AAA) as a short address if it is selected.
#define DALI_VERIFY_SHORT_ADDRESS 0x00B9 // 268 - Is the short address AAA AAA?
#define DALI_QUERY_SHORT_ADDRESS 0x00BB // 269 - What is the short address of the slaveNote 2being selected?
#define DALI_PHYSICAL_SELECTION 0x00BD // 270 - not DALI-2 Sets the slave to Physical Selection Mode and excludes the slave from the Compare process. (Excluding IEC62386-102ed2.0)
#define DALI_RESERVED271 0x00BF // 271 - [Reserved]
// Extending special commands - Send as first byte
#define DALI_ENABLE_DEVICE_TYPE_X 0x00C1 // 272 - Adds the device XXXX (a special device).
#define DALI_DATA_TRANSFER_REGISTER1 0x00C3 // 273 - Stores data XXXX into DTR1.
#define DALI_DATA_TRANSFER_REGISTER2 0x00C5 // 274 - Stores data XXXX into DTR2.
#define DALI_WRITE_MEMORY_LOCATION 0x00C7 // 275 - Write data into the specified address of the specified memory bank. (There is BW) (DTR(DTR0)：address, DTR1：memory bank number)
#define DALI_WRITE_MEMORY_LOCATION_NO_REPLY 0x00C9 // 276 - DALI-2 Write data into the specified address of the specified memory bank. (There is no BW) (DTR(DTR0)：address, TR1：memory bank number)
#define DALI_RESERVED277 0x00CB // 277 - [Reserved]
#define DALI_RESERVED349 0x00FD // 349 - [Reserved]
// Address type - Send as first byte
#define DALI_BROADCAST_DP 0x00FE // 0b11111110 254 - Broadcast address
#define DALI_MAX_STORED 17 // Store broadcast and group states
#define DALI_TOPIC "DALI"
#define D_PRFX_DALI "Dali"
/*********************************************************************************************/
const char kDALICommands[] PROGMEM = D_PRFX_DALI "|" // Prefix
"|" D_CMND_POWER "|" D_CMND_DIMMER "|Target"
#ifdef USE_LIGHT
"|Light"
#endif // USE_LIGHT
"|Send|Query|Scan|Group"
"|GroupSliders|Gear";
void (* const DALICommand[])(void) PROGMEM = {
&CmndDali, &CmndDaliPower, &CmndDaliDimmer, &CmndDaliTarget,
#ifdef USE_LIGHT
&CmndDaliLight,
#endif // USE_LIGHT
&CmndDaliSend, &CmndDaliQuery, &CmndDaliScan, &CmndDaliGroup,
&CmndDaliGroupSliders, &CmndDaliGear };
struct DALI {
uint32_t bit_cycles;
uint32_t last_activity;
uint32_t received_dali_data; // Data received from DALI bus
uint8_t pin_rx;
uint8_t pin_tx;
uint8_t max_short_address;
uint8_t address;
uint8_t command;
uint8_t last_dimmer;
uint8_t dimmer[DALI_MAX_STORED];
uint8_t web_dimmer[DALI_MAX_STORED];
uint8_t target;
bool allow_light;
bool last_power;
bool power[DALI_MAX_STORED];
bool available;
bool response;
bool light_sync;
bool probe;
bool invert_rx;
bool invert_tx;
} *Dali = nullptr;
/*********************************************************************************************\
* DALI low level
\*********************************************************************************************/
uint32_t DaliTarget2Address(void) {
// 1..64 = Short address
// 101..116 = Group address
// Others = Broadcast
if ((Dali->target >= 1) && (Dali->target <= 64)) { // 1 .. 64
Dali->target -= 1; // Short address
Dali->target <<= 1;
}
else if ((Dali->target >= 101) && (Dali->target <= 116)) { // 101 .. 116
Dali->target -= 101;
Dali->target <<= 1;
Dali->target |= 0x80; // Group address
}
else { // Others
Dali->target = DALI_BROADCAST_DP; // Broadcast address
}
return Dali->target &0xFE; // Direct Arc Power Control command
}
/*
uint32_t DaliAddress2Target(uint32_t adr) {
if (adr >= 254) { // 0b1111111S
return 0; // Broadcast address (0)
}
else if ((adr >= 128) && (adr <= 159)) { // 0b1000000S .. 0b1001111S
return (adr >> 1) +101; // Group address (101 .. 116)
}
return (adr >> 1) +1; // 0b0000000S .. 0b0111111S Short address (1 .. 64)
}
*/
/*-------------------------------------------------------------------------------------------*/
uint32_t DaliSaveState(uint32_t adr, uint32_t cmd) {
if (adr &0x01) { return 0; } // No address
int index = -1;
if (DALI_BROADCAST_DP == adr) { // Broadcast address
index = 0;
}
adr >>= 1;
if ((adr >= 0x40) && (adr <= 0x4F)) { // Group address 0 to 15
index = adr -0x3F;
}
if (index >= 0) {
Dali->last_power = Dali->power[index];
Dali->power[index] = (cmd); // State
if (Dali->power[index]) {
Dali->last_dimmer = Dali->dimmer[index];
Dali->dimmer[index] = cmd; // Value
}
if ((0 == index) && !Dali->power[0]) { // Only on Broadcast change to power Off
for (uint32_t i = 0; i < DALI_MAX_STORED; i++) {
Dali->power[i] = false; // Log all group power as Off when Broadcast is Off
}
}
} else {
index = 0; // Use broadcast
}
return index;
}
/*-------------------------------------------------------------------------------------------*/
void DaliEnableRxInterrupt(void) {
Dali->available = false;
attachInterrupt(Dali->pin_rx, DaliReceiveData, (Dali->invert_rx) ? RISING : FALLING);
}
void DaliDisableRxInterrupt(void) {
detachInterrupt(Dali->pin_rx);
}
/*-------------------------------------------------------------------------------------------*\
* DALI receive
\*-------------------------------------------------------------------------------------------*/
void IRAM_ATTR DaliReceiveData(void); // Fix ESP8266 ISR not in IRAM! exception
void DaliReceiveData(void) {
/*
Forward frame (1 Start bit + 16 data bits) * 2 bits/bit (manchester encoding) + 2 * 2 Stop bits = 38 bits
DALI data 0xFE64 1 1 1 1 1 1 1 0 0 1 1 0 0 1 0 0 Forward frame
Start and Stop bits 1 1 1
Manchester data 0101010101010101101001011010011010
Stop bits 1111
Backward frame (1 Start bit + 8 data bits) * 2 bits/bit (manchester encoding) + 2 * 2 Stop bits = 22 bits
DALI data 0x64 0 1 1 0 0 1 0 0 Backward frame
Start and Stop bits 1 1 1
Manchester data 011001011010011010
Stop bits 1111
Bit number 01234567890123456789012345678901234567
1 2 3
*/
if (Dali->available) { return; } // Skip if last input is not yet handled
uint32_t gap_time = millis() - Dali->last_activity;
uint32_t wait = ESP.getCycleCount() + (Dali->bit_cycles / 2);
int bit_state = 0;
bool dali_read;
uint32_t received_dali_data = 0;
uint32_t bit_number = 0;
while (bit_number < 38) {
while (ESP.getCycleCount() < wait);
wait += Dali->bit_cycles; // Auto roll-over
dali_read = (digitalRead(Dali->pin_rx) != Dali->invert_rx);
#ifdef DALI_DEBUG
digitalWrite(DALI_DEBUG_PIN, bit_number&1); // Add LogicAnalyzer poll indication
#endif // DALI_DEBUG
if (bit_number < 34) { // 34 manchester encoded bits
bit_state += (dali_read) ? 1 : -1;
if (0 == bit_state) { // Manchester encoding total 2 bits is always 0
if (bit_number > 2) { // Skip start bit
received_dali_data <<= 1;
received_dali_data |= dali_read;
}
}
else if ((2 == bit_state) &&
(bit_number == 19)) { // Possible backward frame detected - Chk stop bits
bit_state = 0;
bit_number = 35;
}
else if (abs(bit_state) > 1) { // Invalid manchester data (too many 0 or 1)
break;
}
} else { // 4 high Stop bits
if (bit_state != 0) { // Invalid manchester data
break;
}
else if (dali_read != 1) { // Invalid level of stop bit
bit_state = 1;
break;
}
}
bit_number++;
}
Dali->last_activity = millis();
if (bit_state != 0) { // Invalid Manchester encoding including start and stop bits
received_dali_data |= 0x00010000; // Possible collision or invalid reply of repeated frame due to handling of first frame
if (Dali->response) { // Expect backward frame with no collision
AddLog(LOG_LEVEL_DEBUG_MORE, PSTR("DLI: Rx collision"));
}
}
if (Dali->probe) {
AddLog(LOG_LEVEL_DEBUG, PSTR("DLI: Rx %05X %d"), received_dali_data, gap_time);
} else {
if (Dali->response || // Response from last message send
(Dali->received_dali_data != received_dali_data)) { // Skip duplicates
Dali->received_dali_data = received_dali_data;
Dali->available = true; // Any data received
}
}
}
/*-------------------------------------------------------------------------------------------*\
* DALI send
\*-------------------------------------------------------------------------------------------*/
void DaliSendDataOnce(uint16_t send_dali_data) {
/*
DALI protocol forward frame
DALI data 0xFE64 1 1 1 1 1 1 1 0 0 1 1 0 0 1 0 0
Start and Stop bits 1 1 1
Manchester data 0101010101010101101001011010011010
Stop bits 1111
Bit number 01234567890123456789012345678901234567
1 2 3
*/
Dali->last_activity += 14; // As suggested by DALI protocol (> 9.17 ms)
while (!TimeReached(Dali->last_activity)) {
delay(1); // Wait for bus to be free if needed
}
bool bit_value;
bool pin_value;
bool dali_read;
bool collision = false;
uint32_t bit_pos = 15;
uint32_t bit_number = 0;
#ifdef ESP32
{portMUX_TYPE mux = portMUX_INITIALIZER_UNLOCKED;
portENTER_CRITICAL(&mux);
#endif
uint32_t wait = ESP.getCycleCount();
while (bit_number < 35) { // 417 * 35 = 14.7 ms
if (!collision) {
if (0 == (bit_number &1)) { // Even bit
// Start bit, Stop bit, Data bits
bit_value = (0 == bit_number) ? 1 : (34 == bit_number) ? 0 : (bool)((send_dali_data >> bit_pos--) &1); // MSB first
} else { // Odd bit
bit_value = !bit_value; // Complement bit
}
pin_value = bit_value ? LOW : HIGH; // Invert bit
} else {
if (34 == bit_number) {
pin_value = HIGH; // Set to idle
}
}
digitalWrite(Dali->pin_tx, (Dali->invert_tx) ? !pin_value : pin_value);
wait += Dali->bit_cycles; // Auto roll-over
while (ESP.getCycleCount() < wait);
if (!collision) {
dali_read = (digitalRead(Dali->pin_rx) != Dali->invert_rx);
if ((HIGH == pin_value) && (LOW == dali_read)) { // Collision if write is 1 and bus is 0
collision = true;
pin_value = LOW;
bit_number = 29; // Keep bus low for 4 bits
AddLog(LOG_LEVEL_DEBUG_MORE, PSTR("DLI: Tx collision"));
}
}
bit_number++;
}
#ifdef ESP32
portEXIT_CRITICAL(&mux);}
#endif
// delayMicroseconds(1100); // Adds to total 15.8 ms
Dali->last_activity = millis();
}
/*-------------------------------------------------------------------------------------------*/
void DaliSendData(uint32_t adr, uint32_t cmd) {
bool repeat = (adr &0x100); // Set repeat if bit 8 is set
adr &= 0xFF;
cmd &= 0xFF;
Dali->address = adr;
Dali->command = cmd;
DaliSaveState(adr, cmd);
if (!repeat && (adr &0x01)) { // YAAAAAA1 Commands where user didn't set repeat
if ((adr >= 0xA1) && (adr <= 0xFD)) { // Special commands
repeat = ((0xA5 == adr) || (0xA7 == adr));
} else {
// ((cmd >=0) && (cmd <= 31)) // Arc power control commands
repeat = (((cmd >=32) && (cmd <= 143)) || // Configuration commands
((cmd >=224) && (cmd <= 236))); // Extended configuration commands
// ((cmd >=144) && (cmd <= 223)) // Query commands
// ((cmd >=237) && (cmd <= 255)) // Extended query commands
}
}
#ifdef DALI_DEBUG
AddLog(LOG_LEVEL_DEBUG, PSTR("DLI: Tx 0x%d%02X%02X"), repeat, adr, cmd);
#endif // DALI_DEBUG
uint16_t send_dali_data = adr << 8 | cmd;
DaliDisableRxInterrupt();
DaliSendDataOnce(send_dali_data); // Takes 14.7 ms
if (repeat) {
DaliSendDataOnce(send_dali_data); // Takes 14.7 ms
}
delay(2); // Block response
DaliEnableRxInterrupt();
}
/*-------------------------------------------------------------------------------------------*/
int DaliSendWaitResponse(uint32_t adr, uint32_t cmd, uint32_t timeout = DALI_TIMEOUT);
int DaliSendWaitResponse(uint32_t adr, uint32_t cmd, uint32_t timeout) {
Dali->response = true;
DaliSendData(adr, cmd);
while (!Dali->available && timeout--) { // Expect backward frame within DALI_TIMEOUT ms
delay(1);
};
int result = -1; // DALI NO or no response
if (Dali->available) {
Dali->available = false; // DALI collision (-2) or valid data (>=0)
result = (Dali->received_dali_data &0x00010000) ? -2 : Dali->received_dali_data;
}
Dali->response = false;
#ifdef DALI_DEBUG
AddLog(LOG_LEVEL_DEBUG, PSTR("DLI: Rx 0x%05X"), result);
#endif // DALI_DEBUG
return result;
}
/*********************************************************************************************\
* DALI tools
*
* Courtesy of https://github.com/qqqlab/DALI-Lighting-Interface
\*********************************************************************************************/
bool DaliSetValue(uint32_t adr, uint32_t getcmd, uint32_t setcmd, uint32_t v) {
// Set a parameter value, returns true on success
int current_v = DaliSendWaitResponse(adr, getcmd); // Get current parameter value
if (current_v == v) { return true; } // Already set
DaliSendData(DALI_DATA_TRANSFER_REGISTER0, v); // Store value in DTR
int dtr = DaliSendWaitResponse(adr, DALI_QUERY_CONTENT_DTR0); // Get DTR value
if (dtr != v) { return false; }
DaliSendData(adr, setcmd); // Set parameter value = DTR
current_v = DaliSendWaitResponse(adr, getcmd); // Get current parameter value
if (current_v != v) { return false; } // Set failed
return true;
}
bool DaliSetOperatingMode(uint32_t adr, uint32_t v) {
return DaliSetValue(adr, DALI_QUERY_OPERATING_MODE, DALI_SET_OPERATING_MODE, v);
}
bool DaliSetMaxLevel(uint32_t adr, uint32_t v) {
return DaliSetValue(adr, DALI_QUERY_MAX_LEVEL, DALI_SET_MAX_LEVEL, v);
}
bool DaliSetMinLevel(uint32_t adr, uint32_t v) {
return DaliSetValue(adr, DALI_QUERY_MIN_LEVEL, DALI_SET_MIN_LEVEL, v);
}
bool DaliSetSystemFailureLevel(uint32_t adr, uint32_t v) {
return DaliSetValue(adr, DALI_QUERY_SYSTEM_FAILURE_LEVEL, DALI_SET_SYSTEM_FAILURE_LEVEL, v);
}
bool DaliSetPowerOnLevel(uint32_t adr, uint32_t v) {
return DaliSetValue(adr, DALI_QUERY_POWER_ON_LEVEL, DALI_SET_POWER_ON_LEVEL, v);
}
/*-------------------------------------------------------------------------------------------*/
uint32_t DaliGearPresent(void) {
uint32_t count = 0;
for (uint32_t sa = 0; sa < Dali->max_short_address; sa++) { // Scanning 64 addresses takes about 2500 ms
if (DaliSendWaitResponse(sa << 1 | 1, DALI_QUERY_CONTROL_GEAR_PRESENT, 20) >= 0) {
count++;
}
}
return count;
}
/*-------------------------------------------------------------------------------------------*/
void DaliInitLight(void) {
// Taken from Shelly Dali Dimmer ;-)
DaliSendData(DALI_DATA_TRANSFER_REGISTER0, DALI_INIT_FADE); // Fade x second
DaliSendData(0xFF, DALI_SET_FADE_TIME);
DaliSendData(DALI_DATA_TRANSFER_REGISTER0, 0); // Power off after gear power restore
DaliSendData(0xFF, DALI_SET_POWER_ON_LEVEL);
DaliSendData(DALI_DATA_TRANSFER_REGISTER0, 0xFE); // Reset all but short circuit
DaliSendData(0xFF, DALI_SET_SYSTEM_FAILURE_LEVEL);
}
/*********************************************************************************************\
* DALI commissioning short addresses
*
* Courtesy of https://github.com/qqqlab/DALI-Lighting-Interface
\*********************************************************************************************/
void DaliSetSearchAddress(uint32_t adr) {
// Set search address
DaliSendData(DALI_SEARCHADDRH, adr>>16);
DaliSendData(DALI_SEARCHADDRM, adr>>8);
DaliSendData(DALI_SEARCHADDRL, adr);
}
/*-------------------------------------------------------------------------------------------*/
void DaliSetSearchAddressDifference(uint32_t adr_new, uint32_t adr_current) {
// Set search address, but set only changed bytes (takes less time)
if ( (uint8_t)(adr_new>>16) != (uint8_t)(adr_current>>16) ) DaliSendData(DALI_SEARCHADDRH, adr_new>>16);
if ( (uint8_t)(adr_new>>8) != (uint8_t)(adr_current>>8) ) DaliSendData(DALI_SEARCHADDRM, adr_new>>8);
if ( (uint8_t)(adr_new) != (uint8_t)(adr_current) ) DaliSendData(DALI_SEARCHADDRL, adr_new);
}
/*-------------------------------------------------------------------------------------------*/
bool DaliCompare() {
// Is the random address smaller or equal to the search address?
// As more than one device can reply, the reply gets garbled
uint8_t retry = 2;
while (retry > 0) {
// Compare is true if we received any activity on the bus as reply.
// Sometimes the reply is not registered... so only accept retry times 'no reply' as a real false compare
int rv = DaliSendWaitResponse(DALI_COMPARE, 0x00);
if (rv == 0xFF) return true; // Yes reply
if (rv == -2) return true; // Reply but collision
retry--;
}
return false;
}
/*-------------------------------------------------------------------------------------------*/
uint32_t DaliFindAddress(void) {
// Find addr with binary search
uint32_t adr = 0x800000;
uint32_t addsub = 0x400000;
uint32_t adr_last = adr;
DaliSetSearchAddress(adr);
while (addsub) {
DaliSetSearchAddressDifference(adr, adr_last);
adr_last = adr;
if (DaliCompare()) { // Returns true if searchadr > adr
adr -= addsub;
} else {
adr += addsub;
}
addsub >>= 1;
}
DaliSetSearchAddressDifference(adr, adr_last);
adr_last = adr;
if (!DaliCompare()) {
adr++;
DaliSetSearchAddressDifference(adr, adr_last);
}
return adr;
}
/*-------------------------------------------------------------------------------------------*/
void DaliProgramShortAddress(uint8_t shortadr) {
// The slave shall store the received 6-bit address (AAAAAA) as a short address if it is selected.
DaliSendData(DALI_PROGRAM_SHORT_ADDRESS, (shortadr << 1) | 0x01);
AddLog(LOG_LEVEL_INFO, PSTR("DLI: Set short address %d"), shortadr +1);
}
/*-------------------------------------------------------------------------------------------*/
uint32_t DaliCommission(uint8_t init_arg) {
// Based on Shelly DALI Dimmer Gen3 received frames
// init_arg=11111111 : all without short address
// init_arg=00000000 : all
// init_arg=0AAAAAA1 : only for this shortadr
// returns number of new short addresses assigned
DaliSendData(0xFF, DALI_RESET); // Turns ON all lights
uint8_t arr[64];
uint32_t sa;
for (sa = 0; sa < 64; sa++) {
arr[sa] = 0;
}
delay(450);
DaliSendData(DALI_DATA_TRANSFER_REGISTER0, 0xFF);
DaliSendData(0xFF, DALI_SET_SHORT_ADDRESS);
DaliSendData(DALI_TERMINATE, 0x00); // Terminate the DALI_INITIALISE command
delay(15);
// Start commissioning
DaliSendData(DALI_INITIALISE, init_arg);
DaliSendData(DALI_RANDOMISE, 0x00);
delay(65); // Need pause after RANDOMISE
uint32_t cnt = 0;
while (true) { // Find random addresses and assign unused short addresses
uint32_t adr = DaliFindAddress();
if (adr > 0xffffff) { break; } // No more random addresses found -> exit
for (sa = 0; sa < 64; sa++) { // Find first unused short address
if (0 == arr[sa]) { break; }
}
if (sa >= 64) { break; } // All 64 short addresses assigned -> exit
arr[sa] = 1; // Mark short address as used
cnt++;
DaliProgramShortAddress(sa); // Assign short address
DaliSendData(DALI_WITHDRAW, 0x00); // Remove the device from the search
DaliSendData(sa << 1, DALI_OFF); // Turns OFF latest short address light
delay(1);
OsWatchLoop(); // Feed blocked-loop watchdog
}
delay(100);
DaliSendData(DALI_TERMINATE, 0x00); // Terminate the DALI_INITIALISE command
#ifdef USE_LIGHT
DaliInitLight();
uint32_t address = (Settings->sbflag1.dali_light) ? DaliTarget2Address() : DALI_BROADCAST_DP; // DaliLight 1
DaliSendData(address, Dali->power[0]); // Restore lights
#else
DaliSendData(DALI_BROADCAST_DP, Dali->power[0]); // Restore lights
#endif // USE_LIGHT
return cnt;
}
/*********************************************************************************************/
void ResponseAppendDali(uint32_t index) {
char number[12];
uint8_t dimmer = changeUIntScale(Dali->dimmer[index], 0, 254, 0, 100);
ResponseAppend_P(PSTR("\"DALI\":{\"Power%s\":\"%s\",\"Dimmer%s\":%d,\"Address\":%d,\"Command\":%d}"),
(0==index)?"":itoa(index+100, number, 10), GetStateText(Dali->power[index]),
(0==index)?"":itoa(index+100, number, 10), dimmer,
Dali->address, Dali->command);
}
void ResponseDali(uint32_t index) {
Response_P(PSTR("{"));
ResponseAppendDali(index);
ResponseJsonEnd();
}
/*-------------------------------------------------------------------------------------------*/
void DaliLoop(void) {
if (!Dali->available || Dali->response) { return; }
AddLog(LOG_LEVEL_DEBUG_MORE, PSTR("DLI: Rx 0x%05X"), Dali->received_dali_data);
if (Dali->received_dali_data &0x00010000) {
Dali->available = false;
return; // Rx collision
}
Dali->address = Dali->received_dali_data >> 8;
Dali->command = Dali->received_dali_data;
uint32_t index = DaliSaveState(Dali->address, Dali->command); // Update dimmer and power
bool show_response = true;
#ifdef USE_LIGHT
if (Dali->allow_light && (DaliTarget2Address() == Dali->address)) {
if (Settings->sbflag1.dali_light) { // DaliLight 1
uint8_t dim_old = changeUIntScale(Dali->last_dimmer, 0, 254, 0, 100);
uint8_t dim_new = changeUIntScale(Dali->dimmer[index], 0, 254, 0, 100);
if (Dali->last_power != Dali->power[index]) {
Dali->light_sync = true; // Block local loop
ExecuteCommandPower(LightDevice(), Dali->power[index], SRC_SWITCH);
}
else if (dim_old != dim_new) {
char scmnd[20];
snprintf_P(scmnd, sizeof(scmnd), PSTR(D_CMND_DIMMER " %d"), dim_new);
Dali->light_sync = true; // Block local loop
ExecuteCommand(scmnd, SRC_SWITCH);
}
show_response = false;
}
}
#endif // USE_LIGHT
if (show_response) {
ResponseDali(index);
MqttPublishPrefixTopicRulesProcess_P(RESULT_OR_TELE, PSTR(D_PRFX_DALI));
}
Dali->available = false;
}
/*-------------------------------------------------------------------------------------------*/
void DaliEverySecond(void) {
if (5 == TasmotaGlobal.uptime) {
DaliInitLight();
}
}
/*-------------------------------------------------------------------------------------------*/
#ifdef USE_LIGHT
bool DaliSetChannels(void) {
if (Settings->sbflag1.dali_light) { // DaliLight 1
Settings->light_fade = 0; // Use Dali fading
Settings->light_correction = 0; // Use Dali light correction
if (Dali->light_sync) { // Block local loop
Dali->light_sync = false;
} else {
uint8_t value = ((uint8_t*)XdrvMailbox.data)[0];
if (255 == value) { value = 254; } // Max Dali value
DaliSendData(DaliTarget2Address(), value);
}
}
return true;
}
#endif // USE_LIGHT
/*-------------------------------------------------------------------------------------------*/
bool DaliInit(uint32_t function) {
int pin_tx = -1;
bool invert_tx = false;
if (PinUsed(GPIO_DALI_TX)) {
pin_tx = Pin(GPIO_DALI_TX);
}
else if (PinUsed(GPIO_DALI_TX_INV)) {
pin_tx = Pin(GPIO_DALI_TX_INV);
invert_tx = true;
}
int pin_rx = -1;
bool invert_rx = false;
if (PinUsed(GPIO_DALI_RX)) {
pin_rx = Pin(GPIO_DALI_RX);
}
else if (PinUsed(GPIO_DALI_RX_INV)) {
pin_rx = Pin(GPIO_DALI_RX_INV);
invert_rx = true;
}
if ((-1 == pin_tx) || (-1 == pin_rx)) { return false; }
Dali = (DALI*)calloc(sizeof(DALI), 1);
if (!Dali) { return false; }
Dali->pin_tx = pin_tx;
Dali->invert_tx = invert_tx;
Dali->pin_rx = pin_rx;
Dali->invert_rx = invert_rx;
Dali->allow_light = (FUNC_MODULE_INIT == function); // Light control is possible
AddLog(LOG_LEVEL_INFO, PSTR("DLI: GPIO%d(RX%s) and GPIO%d(TX%s)%s"),
Dali->pin_rx, (Dali->invert_rx)?"i":"", Dali->pin_tx, (Dali->invert_tx)?"i":"", (Dali->allow_light)?" as light":"");
pinMode(Dali->pin_tx, OUTPUT);
digitalWrite(Dali->pin_tx, (Dali->invert_tx) ? LOW : HIGH); // Idle
pinMode(Dali->pin_rx, INPUT);
#ifdef DALI_DEBUG
pinMode(DALI_DEBUG_PIN, OUTPUT);
digitalWrite(DALI_DEBUG_PIN, HIGH);
#endif // DALI_DEBUG
Dali->max_short_address = 64;
for (uint32_t i = 0; i < DALI_MAX_STORED; i++) {
Dali->dimmer[i] = DALI_INIT_STATE;
}
// Manchester twice 1200 bps = 2400 bps = 417 (protocol 416.76 +/- 10%) us
Dali->bit_cycles = ESP.getCpuFreqMHz() * 1000000 / 2400;
DaliEnableRxInterrupt();
if (!Dali->allow_light) {
Settings->sbflag1.dali_light = false; // No light control possible
}
#ifdef USE_LIGHT
if (!Settings->sbflag1.dali_light) { // DaliLight 0
return false;
}
Settings->light_fade = 0; // Use Dali fading instead
Settings->light_correction = 0; // Use Dali light correction
UpdateDevicesPresent(1);
TasmotaGlobal.light_type = LT_SERIAL1; // Single channel
return true;
#else
return false;
#endif // USE_LIGHT
}
/*********************************************************************************************\
* Commands
\*********************************************************************************************/
bool DaliJsonParse(void) {
// {"addr":254,"cmd":100}
// {"addr":2}
// {"dim":3}
bool served = false;
JsonParser parser((char *)XdrvMailbox.data);
JsonParserObject root = parser.getRootObject();
if (root) {
int DALIindex = 0;
int ADRindex = 0;
int8_t DALIdim = -1;
uint32_t DALIaddr = DALI_BROADCAST_DP;
JsonParserToken val = root[PSTR("cmd")];
if (val) {
uint32_t cmd = val.getUInt();
val = root[PSTR("addr")];
if (val) {
uint32_t addr = val.getUInt();
AddLog(LOG_LEVEL_DEBUG, PSTR("DLI: cmd = %d, addr = %d"), cmd, addr);
DaliSendData(addr, cmd);
return true;
} else {
return false;
}
}
val = root[PSTR("addr")];
if (val) {
uint32_t addr = val.getUInt();
if ((addr >= 0) && (addr < 64)) {
DALIaddr = addr << 1;
}
}
val = root[PSTR("dim")];
if (val) {
uint8_t dim = val.getUInt();
if (dim < 255) {
DALIdim = dim;
}
}
DaliSendData(DALIaddr, DALIdim);
served = true;
}
return served;
}
/*- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -*/
void CmndDali(void) {
// Dali {"addr":254,"cmd":100} - Any address and/or command
// Dali 0|1 - Enable DALI receive probe
if (XdrvMailbox.data_len > 0) {
if ((XdrvMailbox.payload >= 0) && (XdrvMailbox.payload <= 1)) {
Dali->probe = XdrvMailbox.payload;
ResponseCmndNumber(Dali->probe);
return;
}
DaliJsonParse();
}
ResponseDali(0);
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliTarget(void) {
// DaliTarget - Set transmit target
// DaliTarget 0 - Set target to broadcast address
// DaliTarget 1..64 - Set target to short address
// DaliTarget 101..116 - Set target to group address
if (((XdrvMailbox.payload >= 1) && (XdrvMailbox.payload <= 64)) ||
((XdrvMailbox.payload >= 101) && (XdrvMailbox.payload <= 116)) ||
(XdrvMailbox.payload == 0)) {
Dali->target = XdrvMailbox.payload;
}
ResponseCmndNumber(Dali->target);
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliPower(void) {
// DaliPower 0 - Broadcast power off
// DaliPower 1 - Broadcast power on to last dimmer state
// DaliPower 2 - Broadcast toggle power off or last dimmer state
// DaliPower 3..254 - Broadcast equals DaliDimmer command
// DaliPower 0..254 - Broadcast control
// DaliPower0 0..254 - Broadcast control (= DaliPower)
// DaliPower1 0..254 - Short address 0 control
// DaliPower3 0..254 - Short address 2 control
uint32_t index = 0; // Broadcast
if ((XdrvMailbox.index >= 101) && (XdrvMailbox.index <= 116)) {
index = XdrvMailbox.index - 100; // Group1 to 16
}
if (((XdrvMailbox.index >= 0) && (XdrvMailbox.index <= 64)) ||
((XdrvMailbox.index >= 101) && (XdrvMailbox.index <= 116))) {
if ((XdrvMailbox.payload >= 0) && (XdrvMailbox.payload <= 254)) {
if (XdrvMailbox.payload <= 2) {
if (2 == XdrvMailbox.payload) {
XdrvMailbox.payload = (Dali->power[index]) ? 0 : 1;
}
if (1 == XdrvMailbox.payload) {
XdrvMailbox.payload = Dali->dimmer[index];
}
}
uint32_t DALIaddr = DALI_BROADCAST_DP;
if (XdrvMailbox.index >= 101) {
DALIaddr = ((XdrvMailbox.index -101) << 1) | 0x80; // Group address
}
else if ((XdrvMailbox.index > 0) && XdrvMailbox.usridx) {
DALIaddr = (XdrvMailbox.index -1) << 1; // Short address
}
DaliSendData(DALIaddr, XdrvMailbox.payload);
}
}
ResponseDali(index);
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliDimmer(void) {
// DaliDimmer 0..100 - Broadcast set power off or dimmer state
// DaliDimmer0 0..100 - Broadcast set power off or dimmer state
// DaliDimmer1 0..100 - Short address 0 set power off or dimmer state
// DaliDimmer3 0..100 - Short address 2 set power off or dimmer state
uint32_t index = 0; // Broadcast
if ((XdrvMailbox.index >= 101) && (XdrvMailbox.index <= 116)) {
index = XdrvMailbox.index - 100; // Group1 to 16
}
if (((XdrvMailbox.index >= 0) && (XdrvMailbox.index <= 64)) ||
((XdrvMailbox.index >= 101) && (XdrvMailbox.index <= 116))) {
if ((XdrvMailbox.payload >= 0) && (XdrvMailbox.payload <= 100)) {
uint8_t dimmer = changeUIntScale(XdrvMailbox.payload, 0, 100, 0, 254);
uint32_t DALIaddr = DALI_BROADCAST_DP;
if (XdrvMailbox.index >= 101) {
DALIaddr = ((XdrvMailbox.index -101) << 1) | 0x80; // Group address
}
else if ((XdrvMailbox.index > 0) && XdrvMailbox.usridx) {
DALIaddr = (XdrvMailbox.index -1) << 1; // Short address
}
DaliSendData(DALIaddr, dimmer);
}
}
ResponseDali(index);
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliGroup(void) {
// DaliGroup1 1,2 - Add device 1 and 2 to group 1
// DaliGroup1 -1,2 - Remove device 1 and 2 to group 1
if ((XdrvMailbox.index >= 1) && (XdrvMailbox.index <= 16)) {
uint32_t group = XdrvMailbox.index -1;
bool more = false;
char temp[200] = { 0 };
if (XdrvMailbox.data_len) {
uint32_t command = DALI_ADD_TO_GROUP0;
temp[0] = '+';
if ('+' == XdrvMailbox.data[0]) { // Add devices
XdrvMailbox.data++;
XdrvMailbox.data_len--;
}
else if ('-' == XdrvMailbox.data[0]) { // Remove devices
command = DALI_REMOVE_FROM_GROUP0;
XdrvMailbox.data++;
XdrvMailbox.data_len--;
temp[0] = '-';
}
uint32_t argc = ArgC(); // Number of devices
if (argc) {
command |= group;
uint32_t sas[argc];
ParseParameters(argc, sas);
for (uint32_t arg = 0; arg < argc; arg++) {
uint32_t sa = sas[arg] -1;
if (sa < 64) {
snprintf_P(temp, sizeof(temp), PSTR("%s%s%d"), temp, (more)?",":"", sa +1);
more = true;
DaliSendData(sa << 1 | 1, command);
}
}
ResponseCmndIdxChar(temp);
}
} else {
uint32_t command = DALI_QUERY_GROUPS_0_7;
uint32_t bitmask = 1 << group;
if (group > 7) {
command = DALI_QUERY_GROUPS_8_15;
bitmask = 1 << group - 8;
}
for (uint32_t sa = 0; sa < Dali->max_short_address; sa++) { // Scanning 64 addresses takes about 2500 ms
int result = DaliSendWaitResponse(sa << 1 | 1, command, 20);
if ((result >= 0) && (result & bitmask)) {
snprintf_P(temp, sizeof(temp), PSTR("%s%s%d"), temp, (more)?",":"", sa +1);
more = true;
}
}
if (!strlen(temp)) {
snprintf_P(temp, sizeof(temp), PSTR("None"));
}
ResponseCmndIdxChar(temp);
}
}
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliGear(void) {
if ((XdrvMailbox.payload >= 1) && (XdrvMailbox.payload <= 64)) {
Dali->max_short_address = XdrvMailbox.payload;
}
uint32_t count = DaliGearPresent();
ResponseCmnd();
ResponseAppend_P(PSTR("%d,\"Present\":%d}"), Dali->max_short_address, count);
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliSend(void) {
// Send command
// Setting bit 8 will repeat command once
// DaliSend 0x1a5,255 - DALI Initialise (send twice)
// DaliSend 0x01,0xa3,0x2d,254 - Set Power On level
uint32_t values[4] = { 0 };
uint32_t params = ParseParameters(4, values);
if (2 == params) {
DaliSendData(values[0] &0x1FF, values[1] &0xFF);
ResponseCmndDone();
}
else if (4 == params) {
if (DaliSetValue(values[0] &0x1FF, values[1] &0xFF, values[2] &0xFF, values[3] &0xFF)) {
ResponseCmndDone();
} else {
ResponseCmndFailed();
}
}
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliQuery(void) {
// Send command and return response or -1 (no response within DALI_TIMEOUT)
// Setting bit 8 will repeat command once
// DaliQuery 0xff,0x90 - DALI Query status
// DaliQuery 0xff,144 - DALI Query status
uint32_t values[2] = { 0 };
uint32_t params = ParseParameters(2, values);
if (2 == params) {
int result = DaliSendWaitResponse(values[0] &0x1FF, values[1] &0xFF);
ResponseCmndNumber(result);
}
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliScan(void) {
// Scan short addresses
// DaliScan 1 - Reset and commission short addresses
// DaliScan 2 - Commission unassigned short addresses
if ((XdrvMailbox.payload >= 1) && (XdrvMailbox.payload <= 2)) {
uint32_t init_arg = 0x00; // Commission all
if (2 == XdrvMailbox.payload) {
init_arg = 0xFF; // Commission all without short addresses
}
int result = DaliCommission(init_arg);
ResponseCmndNumber(result);
}
}
/*-------------------------------------------------------------------------------------------*/
void CmndDaliGroupSliders(void) {
// DaliGroupSliders 0..16 - Add group sliders
if ((XdrvMailbox.payload >= 0) && (XdrvMailbox.payload <= 16)) {
Settings->mbflag2.dali_group_sliders = XdrvMailbox.payload;
TasmotaGlobal.restart_flag = 2; // Restart to update GUI
}
ResponseCmndNumber(Settings->mbflag2.dali_group_sliders);
}
#ifdef USE_LIGHT
/*-------------------------------------------------------------------------------------------*/
void CmndDaliLight(void) {
// DaliLight 0 - Disable light controls
// DaliLight 1 - Enable light controls
if (Dali->allow_light && (XdrvMailbox.data_len > 0)) {
Settings->sbflag1.dali_light = XdrvMailbox.payload &1; // DaliLight 0/1
TasmotaGlobal.restart_flag = 2; // Restart to update GUI
}
ResponseCmndStateText(Settings->sbflag1.dali_light); // DaliLight 0/1
}
#endif // USE_LIGHT
/*********************************************************************************************\
* Presentation
\*********************************************************************************************/
#ifdef USE_WEBSERVER
const char HTTP_MSG_SLIDER_DALI[] PROGMEM =
"<tr>"
"<td style='width:15%%'><button id='k75%d' style='background:#%06x;' onclick='la(\"&k75=%d\");'>%s%s</button></td>"
"<td style='width:85%%'><div class='r' style='background-image:linear-gradient(to right,#000,#FFF);'>"
"<input id='i75%d' type='range' min='1' max='100' value='%d' onchange='lc(\"i\",75%d,value)'></div></td>"
"</tr>";
void DaliWebAddMainSlider(void) {
WSContentSend_P(HTTP_TABLE100);
char number[12];
for (uint32_t i = Settings->sbflag1.dali_light; i <= Settings->mbflag2.dali_group_sliders; i++) { // DaliLight 0/1, DaliGroupSliders
Dali->web_dimmer[i] = Dali->dimmer[i];
WSContentSend_P(HTTP_MSG_SLIDER_DALI, // Brightness - Black to White
i, // k75<i>
WebColor((Dali->power[i]) ? COL_BUTTON : COL_BUTTON_OFF),
i, // k75=<i>
(0==i)?"B":"G", // B (Broadcast) or G1 to G16 (Group)
(0==i)?"":itoa(i, number, 10),
i, // i75<i>
changeUIntScale(Dali->web_dimmer[i], 0, 254, 0, 100),
i // i75<i>
);
}
WSContentSend_P(PSTR("</table>"));
}
/*********************************************************************************************/
void DaliWebGetArg(void) {
char tmp[8]; // WebGetArg numbers only
char svalue[32]; // Command and number parameter
char webindex[8]; // WebGetArg name
uint32_t index;
for (uint32_t i = Settings->sbflag1.dali_light; i <= Settings->mbflag2.dali_group_sliders; i++) { // DaliLight 0/1, DaliGroupSliders
snprintf_P(webindex, sizeof(webindex), PSTR("i75%d"), i);
WebGetArg(webindex, tmp, sizeof(tmp)); // 0 - 100 percent
if (strlen(tmp)) {
index = i;
if (index > 0) { index += 100; } // Group
snprintf_P(svalue, sizeof(svalue), PSTR("DaliDimmer%d %s"), index, tmp);
ExecuteWebCommand(svalue);
}
}
WebGetArg(PSTR("k75"), tmp, sizeof(tmp));
if (strlen(tmp)) {
index = atoi(tmp);
if (index > 0) { index += 100; } // Group
snprintf_P(svalue, sizeof(svalue), PSTR("DaliPower%d 2"), index);
ExecuteWebCommand(svalue);
}
}
/*********************************************************************************************/
void DaliWebShow(void) {
WSContentSend_P(PSTR("</table>")); // Terminate current {t}
WSContentSend_P(HTTP_MSG_EXEC_JAVASCRIPT); // "<img style='display:none;' src onerror=\""
for (uint32_t i = Settings->sbflag1.dali_light; i <= Settings->mbflag2.dali_group_sliders; i++) { // DaliLight 0/1, DaliGroupSliders
WSContentSend_P(PSTR("eb('k75%d').style='background:#%06x';"),
i, WebColor((Dali->power[i]) ? COL_BUTTON : COL_BUTTON_OFF));
if (Dali->dimmer[i] != Dali->web_dimmer[i]) {
if (WebUpdateSliderTime()) {
Dali->web_dimmer[i] = Dali->dimmer[i];
}
WSContentSend_P(PSTR("eb('i75%d').value='%d';"),
i, changeUIntScale(Dali->dimmer[i], 0, 254, 0, 100));
}
}
WSContentSend_P(PSTR("\">{t}")); // Restart {t} = <table style='width:100%'>
WSContentSeparator(3); // Don't print separator on next WSContentSeparator(1)
}
#endif // USE_WEBSERVER
/*********************************************************************************************\
* Interface
\*********************************************************************************************/
bool Xdrv75(uint32_t function) {
bool result = false;
if (FUNC_MODULE_INIT == function) { // Try to claim DALI as light
result = DaliInit(function);
}
else if ((FUNC_PRE_INIT == function) && !Dali) { // If claim failed then use DALI controls only
DaliInit(function);
}
else if (Dali) {
switch (function) {
case FUNC_LOOP:
DaliLoop();
break;
case FUNC_EVERY_SECOND:
DaliEverySecond();
break;
#ifdef USE_LIGHT
case FUNC_SET_CHANNELS:
result = DaliSetChannels();
break;
#endif // USE_LIGHT
case FUNC_JSON_APPEND:
ResponseAppend_P(PSTR(","));
ResponseAppendDali(0);
break;
#ifdef USE_WEBSERVER
case FUNC_WEB_SENSOR:
DaliWebShow();
break;
case FUNC_WEB_ADD_MAIN_BUTTON:
DaliWebAddMainSlider();
break;
case FUNC_WEB_GET_ARG:
DaliWebGetArg();
break;
#endif // USE_WEBSERVER
case FUNC_COMMAND:
result = DecodeCommand(kDALICommands, DALICommand);
break;
case FUNC_ACTIVE:
result = true;
break;
}
}
return result;
}
#endif // USE_DALI
Reference in New Issue View Git Blame Copy Permalink