Tasmota/sonoff/sonoff_post.h

770 lines
57 KiB
C

/*
sonoff_post.h - Post header file for Sonoff-Tasmota
Copyright (C) 2019 Theo Arends
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef _SONOFF_POST_H_
#define _SONOFF_POST_H_
/*********************************************************************************************\
* Function declarations
\*********************************************************************************************/
#ifdef __cplusplus
extern "C" {
#endif
#include "user_interface.h"
// Function prototypes
void WifiWpsStatusCallback(wps_cb_status status);
#ifdef __cplusplus
}
#endif
//#ifdef USE_KNX // Enabling this will fail compilation. It has no impact if not used. (20180417)
#include <esp-knx-ip.h>
void KNX_CB_Action(message_t const &msg, void *arg);
//#endif // USE_KNX
char* ToHex_P(const unsigned char * in, size_t insz, char * out, size_t outsz, char inbetween = '\0');
/*********************************************************************************************\
* Default global defines
\*********************************************************************************************/
#ifndef ENERGY_OVERTEMP
#define ENERGY_OVERTEMP 90 // Overtemp in Celsius
#endif
#ifdef USE_EMULATION_HUE
#define USE_EMULATION
#endif
#ifdef USE_EMULATION_WEMO
#define USE_EMULATION
#endif
#ifdef USE_MQTT_TLS
const uint16_t WEB_LOG_SIZE = 2000; // Max number of characters in weblog
#else
const uint16_t WEB_LOG_SIZE = 4000; // Max number of characters in weblog
#endif
#if defined(USE_MQTT_TLS) && defined(ARDUINO_ESP8266_RELEASE_2_3_0)
#error "TLS is no more supported on Core 2.3.0, use 2.4.2 or higher."
#endif
#ifndef MODULE
#define MODULE SONOFF_BASIC // [Module] Select default model
#endif
/*********************************************************************************************\
* [sonoff-sensors.bin]
* Provide an image with useful supported sensors enabled
\*********************************************************************************************/
#ifdef FIRMWARE_SENSORS
#undef CODE_IMAGE
#define CODE_IMAGE 3
#undef USE_DISCOVERY // Disable mDNS (+8k code or +23.5k code with core 2_5_x, +0.3k mem)
// -- Optional modules ----------------------------
//#define ROTARY_V1 // Add support for MI Desk Lamp
#define USE_SONOFF_RF // Add support for Sonoff Rf Bridge (+3k2 code)
#define USE_RF_FLASH // Add support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB (+2k7 code)
#define USE_SONOFF_SC // Add support for Sonoff Sc (+1k1 code)
#define USE_TUYA_MCU // Add support for Tuya Serial MCU
#ifndef TUYA_DIMMER_ID
#define TUYA_DIMMER_ID 0 // Default dimmer Id
#endif
//#define USE_ARMTRONIX_DIMMERS // Add support for Armtronix Dimmers (+1k4 code)
#define USE_PS_16_DZ // Add support for PS-16-DZ Dimmer (+2k code)
#define USE_SONOFF_IFAN // Add support for Sonoff iFan02 and iFan03 (+2k code)
#define USE_BUZZER // Add support for a buzzer (+0k6 code)
#define USE_ARILUX_RF // Add support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0))
//#define USE_SHUTTER // Add Shutter support for up to 4 shutter with different motortypes (+6k code)
//#define USE_DEEPSLEEP // Add support for deepsleep (+1k code)
//#define USE_EXS_DIMMER // Add support for EX-Store WiFi Dimmer
// -- Optional light modules ----------------------
#define USE_LIGHT // Add Dimmer/Light support
#define USE_WS2812 // WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by //
// #define USE_WS2812_DMA // DMA supports only GPIO03 (= Serial RXD) (+1k mem). When USE_WS2812_DMA is enabled expect Exceptions on Pow
#ifndef USE_WS2812_HARDWARE
#define USE_WS2812_HARDWARE NEO_HW_WS2812 // Hardware type (NEO_HW_WS2812, NEO_HW_WS2812X, NEO_HW_WS2813, NEO_HW_SK6812, NEO_HW_LC8812, NEO_HW_APA106)
#endif
#ifndef USE_WS2812_CTYPE
#define USE_WS2812_CTYPE NEO_GRB // Color type (NEO_RGB, NEO_GRB, NEO_BRG, NEO_RBG, NEO_RGBW, NEO_GRBW)
#endif
#define USE_MY92X1 // Add support for MY92X1 RGBCW led controller as used in Sonoff B1, Ailight and Lohas
#define USE_SM16716 // Add support for SM16716 RGB LED controller (+0k7 code)
#define USE_SM2135 // Add support for SM2135 RGBCW led control as used in Action LSC (+0k6 code)
#define USE_SONOFF_L1 // Add support for Sonoff L1 led control
#define USE_COUNTER // Enable counters
#undef USE_ADC_VCC // Add Analog input on selected devices
#define USE_DS18x20 // Add support for DS18x20 sensors with id sort, single scan and read retry (+1k3 code)
#define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram)
#define USE_SHT // Add I2C emulating code for SHT1X sensor (+1k4 code)
#define USE_HTU // Add I2C code for HTU21/SI7013/SI7020/SI7021 sensor (+1k5 code)
#define USE_BMP // Add I2C code for BMP085/BMP180/BMP280/BME280 sensor (+4k code)
#define USE_BME680 // Add additional support for BME680 sensor using Bosch BME680 library (+4k code)
#define USE_BH1750 // Add I2C code for BH1750 sensor (+0k5 code)
#define USE_VEML6070 // Add I2C code for VEML6070 sensor (+0k5 code)
#define USE_ADS1115 // Add I2C code for ADS1115 16 bit A/D converter based on Adafruit ADS1x15 library (no library needed) (+0k7 code)
//#define USE_ADS1115_I2CDEV // Add I2C code for ADS1115 16 bit A/D converter using library i2cdevlib-Core and i2cdevlib-ADS1115 (+2k code)
#define USE_INA219 // Add I2C code for INA219 Low voltage and current sensor (+1k code)
//#define USE_INA226 // Enable INA226 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+2k3 code)
#define USE_SHT3X // Add I2C code for SHT3x sensor (+0k6 code)
#define USE_TSL2561 // Add I2C code for TSL2561 sensor using library Adafruit TSL2561 Arduino (+1k2 code)
#define USE_MGS // Add I2C code for Xadow and Grove Mutichannel Gas sensor using library Multichannel_Gas_Sensor (+10k code)
#define USE_SGP30 // Add I2C code for SGP30 sensor (+1k1 code)
//#define USE_SI1145 // Add I2C code for SI1145/46/47 sensor (+1k code)
#define USE_LM75AD // Add I2C code for LM75AD sensor (+0k5 code)
//#define USE_APDS9960 // Add I2C code for APDS9960 Proximity Sensor. Disables SHT and VEML6070 (+4k7 code)
//#define USE_MCP230xx // Enable MCP23008/MCP23017 - Must define I2C Address in #define USE_MCP230xx_ADDR below - range 0x20 - 0x27 (+4k7 code)
// #define USE_MCP230xx_ADDR 0x20 // Enable MCP23008/MCP23017 I2C Address to use (Must be within range 0x20 through 0x27 - set according to your wired setup)
// #define USE_MCP230xx_OUTPUT // Enable MCP23008/MCP23017 OUTPUT support through sensor29 commands (+1k5 code)
// #define USE_MCP230xx_DISPLAYOUTPUT // Enable MCP23008/MCP23017 to display state of OUTPUT pins on Web UI (+0k2 code)
//#define USE_PCA9685 // Enable PCA9685 I2C HW PWM Driver - Must define I2C Address in #define USE_PCA9685_ADDR below - range 0x40 - 0x47 (+1k4 code)
// #define USE_PCA9685_ADDR 0x40 // Enable PCA9685 I2C Address to use (Must be within range 0x40 through 0x47 - set according to your wired setup)
// #define USE_PCA9685_FREQ 50 // Define default PWM frequency in Hz to be used (must be within 24 to 1526) - If other value is used, it will rever to 50Hz
//#define USE_MPR121 // Enable MPR121 controller (I2C addresses 0x5A, 0x5B, 0x5C and 0x5D) in input mode for touch buttons (+1k3 code)
//#define USE_CCS811 // Add I2C code for CCS811 sensor (+2k2 code)
//#define USE_MPU6050 // Enable MPU6050 sensor (I2C address 0x68 AD0 low or 0x69 AD0 high) (+2k6 code)
//#define USE_DS3231 // Enable DS3231 external RTC in case no Wifi is avaliable. See docs in the source file (+1k2 code)
//#define USE_MGC3130 // Enable MGC3130 Electric Field Effect Sensor (I2C address 0x42) (+2k7 code, 0k3 mem)
//#define USE_MAX44009 // Enable MAX44009 Ambient Light sensor (I2C addresses 0x4A and 0x4B) (+0k8 code)
#define USE_SCD30 // Enable Sensiron SCd30 CO2 sensor (I2C address 0x61) (+3k3 code)
//#define USE_SPS30 // Enable Sensiron SPS30 particle sensor (I2C address 0x69) (+1.7 code)
#define USE_ADE7953 // Enable ADE7953 Energy monitor as used on Shelly 2.5 (I2C address 0x38) (+1k5)
//#define USE_VL53L0X // Enable VL53L0x time of flight sensor (I2C address 0x29) (+4k code)
//#define USE_MLX90614 // Enable MLX90614 ir temp sensor (I2C address 0x5a) (+0.6k code)
//#define USE_CHIRP // Enable CHIRP soil moisture sensor (variable I2C address, default 0x20)
//#define USE_PAJ7620 // Enable PAJ7620 gesture sensor (I2C address 0x73) (+2.5k code)
//#define USE_PCF8574 // Enable PCF8574 I/O Expander (I2C addresses 0x20 - 0x27 and 0x38 - 0x3F) (+1k9 code)
#define USE_MHZ19 // Add support for MH-Z19 CO2 sensor (+2k code)
#define USE_SENSEAIR // Add support for SenseAir K30, K70 and S8 CO2 sensor (+2k3 code)
#ifndef CO2_LOW
#define CO2_LOW 800 // Below this CO2 value show green light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
#endif
#ifndef CO2_HIGH
#define CO2_HIGH 1200 // Above this CO2 value show red light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
#endif
#define USE_PMS5003 // Add support for PMS5003 and PMS7003 particle concentration sensor (+1k3 code)
//#define PMS_MODEL_PMS3003 // Enable support of PMS3003 instead of PMS5003/PMS7003 (needs the USE_PMS5003 above)
#define USE_NOVA_SDS // Add support for SDS011 and SDS021 particle concentration sensor (+0k7 code)
#define USE_SERIAL_BRIDGE // Add support for software Serial Bridge (+0k8 code)
#define USE_MP3_PLAYER // Use of the DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop
#define MP3_VOLUME 10 // Set the startup volume on init, the range can be 0..30(max)
//#define USE_AZ7798 // Add support for AZ-Instrument 7798 CO2 datalogger
#define USE_PN532_HSU // Add support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem)
#define USE_RDM6300 // Add support for RDM6300 125kHz RFID Reader (+0k8)
#define USE_IBEACON // Add support for bluetooth LE passive scan of ibeacon devices (uses HM17 module)
#define USE_ENERGY_SENSOR // Add energy sensors (-14k code)
#define USE_PZEM004T // Add support for PZEM004T Energy monitor (+2k code)
#define USE_PZEM_AC // Add support for PZEM014,016 Energy monitor (+1k1 code)
#define USE_PZEM_DC // Add support for PZEM003,017 Energy monitor (+1k1 code)
#define USE_MCP39F501 // Add support for MCP39F501 Energy monitor as used in Shelly 2 (+3k1 code)
#define USE_SDM120 // Add support for Eastron SDM120-Modbus energy monitor (+1k1 code)
#define USE_SDM630 // Add support for Eastron SDM630-Modbus energy monitor (+0k6 code)
#define USE_DDS2382 // Add support for Hiking DDS2382 Modbus energy monitor (+0k6 code)
#define USE_DDSU666 // Add support for Chint DDSU666 Modbus energy monitor (+0k6 code)
//#define USE_SOLAX_X1 // Add support for Solax X1 series Modbus log info (+3k1 code)
#define USE_DHT // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor
#define USE_MAX31855 // Add support for MAX31855 K-Type thermocouple sensor using softSPI
//#define USE_MAX31865 // Add support for MAX31865 RTD sensors using softSPI
#define USE_IR_REMOTE // Send IR remote commands using library IRremoteESP8266 and ArduinoJson (+4k code, 0k3 mem, 48 iram)
#define USE_IR_HVAC // Support for HVAC system using IR (+2k code)
#define USE_IR_RECEIVE // Support for IR receiver (+5k5 code, 264 iram)
//#define USE_ZIGBEE // Enable serial communication with Zigbee CC2530 flashed with ZNP
#define USE_SR04 // Add support for HC-SR04 ultrasonic devices (+1k code)
#define USE_TM1638 // Add support for TM1638 switches copying Switch1 .. Switch8 (+1k code)
#define USE_HX711 // Add support for HX711 load cell (+1k5 code)
//#define USE_HX711_GUI // Add optional web GUI to HX711 as scale (+1k8 code)
//#define USE_TX20_WIND_SENSOR // Add support for La Crosse TX20 anemometer (+2k code)
#define USE_RC_SWITCH // Add support for RF transceiver using library RcSwitch (+2k7 code, 460 iram)
#define USE_RF_SENSOR // Add support for RF sensor receiver (434MHz or 868MHz) (+0k8 code)
// #define USE_THEO_V2 // Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver (+1k4 code)
#define USE_ALECTO_V2 // Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 using 868MHz RF sensor receiver (+1k7 code)
#define USE_HRE // Add support for Badger HR-E Water Meter (+1k4 code)
//#define USE_A4988_STEPPER // Add support for A4988/DRV8825 stepper-motor-driver-circuit (+10k5 code)
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // FIRMWARE_SENSORS
/*********************************************************************************************\
* [sonoff-classic.bin]
* Provide an image close to version 5.12.0 but still within 499k program space to allow one time OTA
\*********************************************************************************************/
#ifdef FIRMWARE_CLASSIC
#undef CODE_IMAGE
#define CODE_IMAGE 2
#define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices
#ifndef USE_WPS
#define USE_WPS // Add support for WPS as initial wifi configuration tool (+33k code, 1k mem (5k mem with core v2.4.2+))
#endif
#ifndef USE_SMARTCONFIG
#define USE_SMARTCONFIG // Add support for Wifi SmartConfig as initial wifi configuration tool (+23k code, +0.6k mem)
#endif
#undef USE_ARDUINO_OTA // Disable support for Arduino OTA
//#undef USE_DOMOTICZ // Disable Domoticz
#undef USE_HOME_ASSISTANT // Disable Home Assistant
#undef USE_KNX // Disable KNX IP Protocol Support
#undef USE_CUSTOM // Disable Custom features
#undef USE_TIMERS // Disable support for up to 16 timers
#undef USE_TIMERS_WEB // Disable support for timer webpage
#undef USE_SUNRISE // Disable support for Sunrise and sunset tools
#undef USE_RULES // Disable support for rules
#undef USE_SCRIPT // Disable support for script (+17k code)
// -- Optional modules ----------------------------
#undef ROTARY_V1 // Disable support for MI Desk Lamp
#undef USE_SONOFF_RF // Disable support for Sonoff Rf Bridge (+3k2 code)
#undef USE_RF_FLASH // Disable support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB
#undef USE_SONOFF_SC // Disable support for Sonoff Sc (+1k1 code)
#undef USE_TUYA_MCU // Disable support for Tuya Serial MCU
#undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code)
#undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer and Sonoff L1 (+2k code)
#undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code)
#undef USE_BUZZER // Disable support for a buzzer (+0k6 code)
#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller
#undef USE_SHUTTER // Disable Shutter support for up to 4 shutter with different motortypes (+6k code)
#undef USE_DEEPSLEEP // Disable support for deepsleep (+1k code)
#undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer
// -- Optional light modules ----------------------
//#undef USE_LIGHT // Disable Dimmer/Light support
#define USE_WS2812 // WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by //
// #define USE_WS2812_DMA // DMA supports only GPIO03 (= Serial RXD) (+1k mem). When USE_WS2812_DMA is enabled expect Exceptions on Pow
#define USE_WS2812_HARDWARE NEO_HW_WS2812 // Hardware type (NEO_HW_WS2812, NEO_HW_WS2812X, NEO_HW_WS2813, NEO_HW_SK6812, NEO_HW_LC8812, NEO_HW_APA106)
#define USE_WS2812_CTYPE NEO_GRB // Color type (NEO_RGB, NEO_GRB, NEO_BRG, NEO_RBG, NEO_RGBW, NEO_GRBW)
#undef USE_MY92X1 // Disable support for MY92X1 RGBCW led controller as used in Sonoff B1, Ailight and Lohas
#undef USE_SM16716 // Disable support for SM16716 RGB LED controller (+0k7 code)
#undef USE_SM2135 // Disable support for SM2135 RGBCW led control as used in Action LSC (+0k6 code)
#undef USE_SONOFF_L1 // Disable support for Sonoff L1 led control
#undef USE_COUNTER // Disable counters
#define USE_DS18x20 // Add support for DS18x20 sensors with id sort, single scan and read retry (+2k6 code)
#undef USE_I2C // Disable all I2C sensors
#undef USE_SPI // Disable all SPI devices
#undef USE_MHZ19 // Disable support for MH-Z19 CO2 sensor
#undef USE_SENSEAIR // Disable support for SenseAir K30, K70 and S8 CO2 sensor
#undef USE_PMS5003 // Disable support for PMS5003 and PMS7003 particle concentration sensor
#undef USE_NOVA_SDS // Disable support for SDS011 and SDS021 particle concentration sensor
#undef USE_SERIAL_BRIDGE // Disable support for software Serial Bridge
#undef USE_MP3_PLAYER // Disable DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop
#undef USE_AZ7798 // Disable support for AZ-Instrument 7798 CO2 datalogger
#undef USE_PN532_HSU // Disable support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem)
#undef USE_RDM6300 // Disable support for RDM6300 125kHz RFID Reader (+0k8)
#undef USE_IBEACON // Disable support for bluetooth LE passive scan of ibeacon devices (uses HM17 module)
//#undef USE_ENERGY_SENSOR // Disable energy sensors (-14k code)
#undef USE_PZEM004T // Disable PZEM004T energy sensor
#undef USE_PZEM_AC // Disable PZEM014,016 Energy monitor
#undef USE_PZEM_DC // Disable PZEM003,017 Energy monitor
#undef USE_MCP39F501 // Disable support for MCP39F501 Energy monitor as used in Shelly 2 (+3k1 code)
#undef USE_SDM120 // Disable support for Eastron SDM120-Modbus energy meter
#undef USE_SDM630 // Disable support for Eastron SDM630-Modbus energy monitor (+0k6 code)
#undef USE_DDS2382 // Disable support for Hiking DDS2382 Modbus energy monitor (+0k6 code)
#undef USE_DDSU666 // Disable support for Chint DDSU666 Modbus energy monitor (+0k6 code)
#undef USE_SOLAX_X1 // Disable support for Solax X1 series Modbus log info (+3k1 code)
#define USE_DHT // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor
#undef USE_MAX31855 // Disable MAX31855 K-Type thermocouple sensor using softSPI
#undef USE_MAX31865 // Disable support for MAX31865 RTD sensors using softSPI
#undef USE_IR_REMOTE // Disable IR remote commands using library IRremoteESP8266 and ArduinoJson
#undef USE_IR_RECEIVE // Disable support for IR receiver
#undef USE_ZIGBEE // Disable serial communication with Zigbee CC2530 flashed with ZNP
#undef USE_SR04 // Disable support for for HC-SR04 ultrasonic devices
#undef USE_TM1638 // Disable support for TM1638 switches copying Switch1 .. Switch8
#undef USE_HX711 // Disable support for HX711 load cell
#undef USE_TX20_WIND_SENSOR // Disable support for La Crosse TX20 anemometer
#undef USE_RC_SWITCH // Disable support for RF transceiver using library RcSwitch
#undef USE_RF_SENSOR // Disable support for RF sensor receiver (434MHz or 868MHz) (+0k8 code)
#undef USE_HRE // Disable support for Badger HR-E Water Meter (+1k4 code)
#undef USE_A4988_STEPPER // Disable support for A4988_Stepper
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // FIRMWARE_CLASSIC
/*********************************************************************************************\
* [sonoff-knx.bin]
* Provide a dedicated KNX image allowing enough code and memory space
\*********************************************************************************************/
#ifdef FIRMWARE_KNX_NO_EMULATION
#undef CODE_IMAGE
#define CODE_IMAGE 4
#ifndef USE_KNX
#define USE_KNX // Enable KNX IP Protocol Support (+23k code, +3k3 mem)
#endif
#undef USE_EMULATION // Disable Belkin WeMo and Hue Bridge emulation for Alexa (-16k code, -2k mem)
#undef USE_EMULATION_HUE // Disable Hue Bridge emulation for Alexa (+14k code, +2k mem common)
#undef USE_EMULATION_WEMO // Disable Belkin WeMo emulation for Alexa (+6k code, +2k mem common)
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // FIRMWARE_KNX_NO_EMULATION
/*********************************************************************************************\
* [sonoff-display.bin]
* Provide an image with display drivers enabled
\*********************************************************************************************/
#ifdef FIRMWARE_DISPLAYS
#undef CODE_IMAGE
#define CODE_IMAGE 6
#undef USE_EMULATION // Disable Belkin WeMo and Hue Bridge emulation for Alexa (-16k code, -2k mem)
#undef USE_EMULATION_HUE // Disable Hue Bridge emulation for Alexa (+14k code, +2k mem common)
#undef USE_EMULATION_WEMO // Disable Belkin WeMo emulation for Alexa (+6k code, +2k mem common)
#undef USE_DOMOTICZ // Disable Domoticz
#undef USE_HOME_ASSISTANT // Disable Home Assistant
// -- Optional modules ----------------------------
#undef ROTARY_V1 // Disable support for MI Desk Lamp
#undef USE_SONOFF_RF // Disable support for Sonoff Rf Bridge (+3k2 code)
#undef USE_RF_FLASH // Disable support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB
#undef USE_SONOFF_SC // Disable support for Sonoff Sc (+1k1 code)
//#undef USE_TUYA_MCU // Disable support for Tuya Serial MCU
#undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code)
#undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer and Sonoff L1 (+2k code)
#undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code)
#undef USE_BUZZER // Disable support for a buzzer (+0k6 code)
#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller
#undef USE_SHUTTER // Disable Shutter support for up to 4 shutter with different motortypes (+6k code)
#undef USE_DEEPSLEEP // Disable support for deepsleep (+1k code)
#undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer
#undef USE_ENERGY_SENSOR // Disable energy sensors (-14k code)
#undef USE_PZEM004T // Disable PZEM004T energy sensor
#undef USE_PZEM_AC // Disable PZEM014,016 Energy monitor
#undef USE_PZEM_DC // Disable PZEM003,017 Energy monitor
#undef USE_MCP39F501 // Disable MCP39F501 Energy monitor as used in Shelly 2
#undef USE_SDM120 // Disable support for Eastron SDM120-Modbus energy meter
#undef USE_SDM630 // Disable support for Eastron SDM630-Modbus energy monitor (+0k6 code)
#undef USE_DDS2382 // Disable support for Hiking DDS2382 Modbus energy monitor (+0k6 code)
#undef USE_DDSU666 // Disable support for Chint DDSU666 Modbus energy monitor (+0k6 code)
#undef USE_SOLAX_X1 // Disable support for Solax X1 series Modbus log info (+3k1 code)
#define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram)
#define USE_DISPLAY // Add I2C Display Support (+2k code)
#define USE_DISPLAY_MODES1TO5 // Enable display mode 1 to 5 in addition to mode 0
#define USE_DISPLAY_LCD // [DisplayModel 1] Enable Lcd display (I2C addresses 0x27 and 0x3F) (+6k code)
#define USE_DISPLAY_SSD1306 // [DisplayModel 2] Enable SSD1306 Oled 128x64 display (I2C addresses 0x3C and 0x3D) (+16k code)
#define USE_DISPLAY_MATRIX // [DisplayModel 3] Enable 8x8 Matrix display (I2C adresseses see below) (+11k code)
#define USE_DISPLAY_SH1106 // [DisplayModel 7] Enable SH1106 Oled 128x64 display (I2C addresses 0x3C and 0x3D)
#define USE_SPI // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC)
#define USE_DISPLAY_ILI9341 // [DisplayModel 4] Enable ILI9341 Tft 480x320 display (+19k code)
#ifndef ARDUINO_ESP8266_RELEASE_2_3_0 // There is not enough spare RAM with core 2.3.0 to support the following
#define USE_DISPLAY_EPAPER_29 // [DisplayModel 5] Enable e-paper 2.9 inch display (+19k code)
#define USE_DISPLAY_EPAPER_42 // [DisplayModel 6] Enable e-paper 4.2 inch display
// #define USE_DISPLAY_ILI9488 // [DisplayModel 8]
// #define USE_DISPLAY_SSD1351 // [DisplayModel 9]
// #define USE_DISPLAY_RA8876 // [DisplayModel 10]
#endif
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // FIRMWARE_DISPLAYS
/*********************************************************************************************\
* [sonoff-ir.bin]
* Provide a dedicated image with IR full protocol support, with limited additional features
\*********************************************************************************************/
#ifdef FIRMWARE_IR
#undef CODE_IMAGE
#define CODE_IMAGE 7
#undef USE_EMULATION
#undef USE_EMULATION_HUE // Disable Hue emulation - only for lights and relays
#undef USE_EMULATION_WEMO // Disable Wemo emulation - only for relays
//#undef USE_DOMOTICZ // Disable Domoticz
//#undef USE_HOME_ASSISTANT // Disable Home Assistant
//#undef USE_KNX // Disable KNX IP Protocol Support
//#undef USE_CUSTOM // Disable Custom features
//#undef USE_TIMERS // Disable support for up to 16 timers
//#undef USE_TIMERS_WEB // Disable support for timer webpage
//#undef USE_SUNRISE // Disable support for Sunrise and sunset tools
//#undef USE_RULES // Disable support for rules
#undef USE_DISCOVERY // Disable mDNS for the following services (+8k code or +23.5k code with core 2_5_x, +0.3k mem)
// -- Optional modules ----------------------------
#undef ROTARY_V1 // Disable support for MI Desk Lamp
#undef USE_SONOFF_RF // Disable support for Sonoff Rf Bridge (+3k2 code)
#undef USE_RF_FLASH // Disable support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB
#undef USE_SONOFF_SC // Disable support for Sonoff Sc (+1k1 code)
#undef USE_TUYA_MCU // Disable support for Tuya Serial MCU
#undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code)
#undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer and Sonoff L1 (+2k code)
#undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code)
#undef USE_BUZZER // Disable support for a buzzer (+0k6 code)
#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller
#undef USE_SHUTTER // Disable Shutter support for up to 4 shutter with different motortypes (+6k code)
#undef USE_DEEPSLEEP // Disable support for deepsleep (+1k code)
#undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer
// -- Optional light modules ----------------------
//#undef USE_LIGHT // Also disable all Dimmer/Light support
#undef USE_WS2812 // Disable WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by //
#undef USE_MY92X1 // Disable support for MY92X1 RGBCW led controller as used in Sonoff B1, Ailight and Lohas
#undef USE_SM16716 // Disable support for SM16716 RGB LED controller (+0k7 code)
#undef USE_SM2135 // Disable support for SM2135 RGBCW led control as used in Action LSC (+0k6 code)
#undef USE_SONOFF_L1 // Disable support for Sonoff L1 led control
#undef USE_ENERGY_SENSOR // Disable energy sensors (-14k code)
#undef USE_PZEM004T // Disable PZEM004T energy sensor
#undef USE_PZEM_AC // Disable PZEM014,016 Energy monitor
#undef USE_PZEM_DC // Disable PZEM003,017 Energy monitor
#undef USE_MCP39F501 // Disable MCP39F501 Energy monitor as used in Shelly 2
#undef USE_SDM120 // Disable support for Eastron SDM120-Modbus energy meter
#undef USE_SDM630 // Disable support for Eastron SDM630-Modbus energy monitor (+0k6 code)
#undef USE_DDS2382 // Disable support for Hiking DDS2382 Modbus energy monitor (+0k6 code)
#undef USE_DDSU666 // Disable support for Chint DDSU666 Modbus energy monitor (+0k6 code)
#undef USE_SOLAX_X1 // Disable support for Solax X1 series Modbus log info (+3k1 code)
#undef USE_DS18x20 // Disable support for DS18x20 sensors with id sort, single scan and read retry (+1k3 code)
#undef USE_I2C // Disable all I2C sensors
#undef USE_SPI // Disable all SPI devices
#undef USE_MHZ19 // Disable support for MH-Z19 CO2 sensor
#undef USE_SENSEAIR // Disable support for SenseAir K30, K70 and S8 CO2 sensor
#undef USE_PMS5003 // Disable support for PMS5003 and PMS7003 particle concentration sensor
#undef USE_NOVA_SDS // Disable support for SDS011 and SDS021 particle concentration sensor
#undef USE_SERIAL_BRIDGE // Disable support for software Serial Bridge
#undef USE_MP3_PLAYER // Disable DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop
#undef USE_AZ7798 // Disable support for AZ-Instrument 7798 CO2 datalogger
#undef USE_PN532_HSU // Disable support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem)
#undef USE_RDM6300 // Disable support for RDM6300 125kHz RFID Reader (+0k8)
#undef USE_IBEACON // Disable support for bluetooth LE passive scan of ibeacon devices (uses HM17 module)
//#define USE_DHT // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor
#undef USE_MAX31855 // Disable MAX31855 K-Type thermocouple sensor using softSPI
#undef USE_MAX31865 // Disable support for MAX31865 RTD sensors using softSPI
#undef USE_SR04 // Disable support for for HC-SR04 ultrasonic devices
#undef USE_TM1638 // Disable support for TM1638 switches copying Switch1 .. Switch8
#undef USE_HX711 // Disable support for HX711 load cell
#undef USE_TX20_WIND_SENSOR // Disable support for La Crosse TX20 anemometer
#undef USE_RC_SWITCH // Disable support for RF transceiver using library RcSwitch
#undef USE_RF_SENSOR // Disable support for RF sensor receiver (434MHz or 868MHz) (+0k8 code)
#undef USE_HRE // Disable support for Badger HR-E Water Meter (+1k4 code)
#undef USE_A4988_STEPPER // Disable support for A4988_Stepper
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // FIRMWARE_IR
/*********************************************************************************************\
* [sonoff-basic.bin]
* Provide an image without sensors
\*********************************************************************************************/
#ifdef FIRMWARE_BASIC
#undef CODE_IMAGE
#define CODE_IMAGE 5
#undef APP_SLEEP
#define APP_SLEEP 1 // Default to sleep = 1 for FIRMWARE_BASIC
#undef USE_WPS // Disable support for WPS as initial wifi configuration tool
#undef USE_SMARTCONFIG // Disable support for Wifi SmartConfig as initial wifi configuration tool
#undef USE_ARDUINO_OTA // Disable support for Arduino OTA
#undef USE_DOMOTICZ // Disable Domoticz
#undef USE_HOME_ASSISTANT // Disable Home Assistant
#undef USE_MQTT_TLS // Disable TLS support won't work as the MQTTHost is not set
#undef USE_KNX // Disable KNX IP Protocol Support
//#undef USE_WEBSERVER // Disable Webserver
#undef USE_WEBSEND_RESPONSE // Disable command WebSend response message (+1k code)
//#undef USE_EMULATION // Disable Wemo or Hue emulation
//#undef USE_EMULATION_HUE // Disable Hue Bridge emulation for Alexa (+14k code, +2k mem common)
//#undef USE_EMULATION_WEMO // Disable Belkin WeMo emulation for Alexa (+6k code, +2k mem common)
#undef USE_CUSTOM // Disable Custom features
#undef USE_DISCOVERY // Disable Discovery services for both MQTT and web server
//#undef USE_TIMERS // Disable support for up to 16 timers
//#undef USE_TIMERS_WEB // Disable support for timer webpage
//#undef USE_SUNRISE // Disable support for Sunrise and sunset tools
//#undef USE_RULES // Disable support for rules
#undef USE_SCRIPT // Add support for script (+17k code)
// -- Optional modules -------------------------
#undef ROTARY_V1 // Disable support for MI Desk Lamp
#undef USE_SONOFF_RF // Disable support for Sonoff Rf Bridge (+3k2 code)
#undef USE_RF_FLASH // Disable support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB
#undef USE_SONOFF_SC // Disable support for Sonoff Sc (+1k1 code)
//#undef USE_TUYA_MCU // Disable support for Tuya Serial MCU
#undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code)
#undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer and Sonoff L1 (+2k code)
#undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code)
#undef USE_BUZZER // Disable support for a buzzer (+0k6 code)
#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller
#undef USE_SHUTTER // Disable Shutter support for up to 4 shutter with different motortypes (+6k code)
#undef USE_DEEPSLEEP // Disable support for deepsleep (+1k code)
#undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer
// -- Optional light modules ----------------------
//#undef USE_LIGHT // Also disable all Dimmer/Light support
#undef USE_WS2812 // Disable WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by //
#undef USE_MY92X1 // Disable support for MY92X1 RGBCW led controller as used in Sonoff B1, Ailight and Lohas
#undef USE_SM16716 // Disable support for SM16716 RGB LED controller (+0k7 code)
#undef USE_SM2135 // Disable support for SM2135 RGBCW led control as used in Action LSC (+0k6 code)
#undef USE_SONOFF_L1 // Disable support for Sonoff L1 led control
#undef USE_COUNTER // Disable counters
#define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices
#undef USE_DS18x20 // Disable DS18x20 sensor
#undef USE_I2C // Disable all I2C sensors and devices
#undef USE_SPI // Disable all SPI devices
#undef USE_DISPLAY // Disable Display support
#undef USE_MHZ19 // Disable support for MH-Z19 CO2 sensor
#undef USE_SENSEAIR // Disable support for SenseAir K30, K70 and S8 CO2 sensor
#undef USE_PMS5003 // Disable support for PMS5003 and PMS7003 particle concentration sensor
#undef USE_NOVA_SDS // Disable support for SDS011 and SDS021 particle concentration sensor
#undef USE_SERIAL_BRIDGE // Disable support for software Serial Bridge
#undef USE_MP3_PLAYER // Disable DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop
#undef USE_AZ7798 // Disable support for AZ-Instrument 7798 CO2 datalogger
#undef USE_PN532_HSU // Disable support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem)
#undef USE_RDM6300 // Disable support for RDM6300 125kHz RFID Reader (+0k8)
#undef USE_IBEACON // Disable support for bluetooth LE passive scan of ibeacon devices (uses HM17 module)
//#undef USE_ENERGY_SENSOR // Disable energy sensors
#undef USE_PZEM004T // Disable PZEM004T energy sensor
#undef USE_PZEM_AC // Disable PZEM014,016 Energy monitor
#undef USE_PZEM_DC // Disable PZEM003,017 Energy monitor
//#undef USE_MCP39F501 // Disable MCP39F501 Energy monitor as used in Shelly 2
#undef USE_SDM120 // Disable support for Eastron SDM120-Modbus energy meter
#undef USE_SDM630 // Disable support for Eastron SDM630-Modbus energy monitor (+0k6 code)
#undef USE_DDS2382 // Disable support for Hiking DDS2382 Modbus energy monitor (+0k6 code)
#undef USE_DDSU666 // Disable support for Chint DDSU666 Modbus energy monitor (+0k6 code)
#undef USE_SOLAX_X1 // Disable support for Solax X1 series Modbus log info (+3k1 code)
#undef USE_DHT // Disable support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor
#undef USE_MAX31855 // Disable MAX31855 K-Type thermocouple sensor using softSPI
#undef USE_MAX31865 // Disable support for MAX31865 RTD sensors using softSPI
#undef USE_IR_REMOTE // Disable IR driver
#undef USE_ZIGBEE // Disable serial communication with Zigbee CC2530 flashed with ZNP
#undef USE_SR04 // Disable support for for HC-SR04 ultrasonic devices
#undef USE_TM1638 // Disable support for TM1638 switches copying Switch1 .. Switch8
#undef USE_HX711 // Disable support for HX711 load cell
#undef USE_TX20_WIND_SENSOR // Disable support for La Crosse TX20 anemometer
#undef USE_RC_SWITCH // Disable support for RF transceiver using library RcSwitch
#undef USE_RF_SENSOR // Disable support for RF sensor receiver (434MHz or 868MHz) (+0k8 code)
#undef USE_HRE // Disable support for Badger HR-E Water Meter (+1k4 code)
#undef USE_A4988_STEPPER // Disable support for A4988_Stepper
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // FIRMWARE_BASIC
/*********************************************************************************************\
* [sonoff-minimal.bin]
* Provide the smallest image possible while still enabling a webserver for intermediate image load
\*********************************************************************************************/
#ifdef FIRMWARE_MINIMAL
#undef CODE_IMAGE
#define CODE_IMAGE 1
#undef USE_WPS // Disable support for WPS as initial wifi configuration tool
#undef USE_SMARTCONFIG // Disable support for Wifi SmartConfig as initial wifi configuration tool
#undef USE_ARDUINO_OTA // Disable support for Arduino OTA
#undef USE_DOMOTICZ // Disable Domoticz
#undef USE_HOME_ASSISTANT // Disable Home Assistant
#undef USE_MQTT_TLS // Disable TLS support won't work as the MQTTHost is not set
#undef USE_KNX // Disable KNX IP Protocol Support
//#undef USE_WEBSERVER // Disable Webserver
#undef USE_WEBSEND_RESPONSE // Disable command WebSend response message (+1k code)
#undef USE_EMULATION // Disable Wemo or Hue emulation
#undef USE_EMULATION_HUE // Disable Hue Bridge emulation for Alexa (+14k code, +2k mem common)
#undef USE_EMULATION_WEMO // Disable Belkin WeMo emulation for Alexa (+6k code, +2k mem common)
#undef USE_CUSTOM // Disable Custom features
#undef USE_DISCOVERY // Disable Discovery services for both MQTT and web server
#undef USE_TIMERS // Disable support for up to 16 timers
#undef USE_TIMERS_WEB // Disable support for timer webpage
#undef USE_SUNRISE // Disable support for Sunrise and sunset tools
#undef USE_RULES // Disable support for rules
#undef USE_SCRIPT // Disable support for script
// -- Optional modules ----------------------------
#undef ROTARY_V1 // Disable support for MI Desk Lamp
#undef USE_SONOFF_RF // Disable support for Sonoff Rf Bridge (+3k2 code)
#undef USE_RF_FLASH // Disable support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB
#undef USE_SONOFF_SC // Disable support for Sonoff Sc (+1k1 code)
#undef USE_TUYA_MCU // Disable support for Tuya Serial MCU
#undef USE_ARMTRONIX_DIMMERS // Disable support for Armtronix Dimmers (+1k4 code)
#undef USE_PS_16_DZ // Disable support for PS-16-DZ Dimmer and Sonoff L1 (+2k code)
#undef USE_SONOFF_IFAN // Disable support for Sonoff iFan02 and iFan03 (+2k code)
#undef USE_BUZZER // Disable support for a buzzer (+0k6 code)
#undef USE_ARILUX_RF // Disable support for Arilux RF remote controller
#undef USE_SHUTTER // Disable Shutter support for up to 4 shutter with different motortypes (+6k code)
#undef USE_DEEPSLEEP // Disable support for deepsleep (+1k code)
#undef USE_EXS_DIMMER // Disable support for EX-Store WiFi Dimmer
// -- Optional light modules ----------------------
#undef USE_LIGHT // Disable support for lights
#undef USE_WS2812 // Disable WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by //
#undef USE_MY92X1 // Disable support for MY92X1 RGBCW led controller as used in Sonoff B1, Ailight and Lohas
#undef USE_SM16716 // Disable support for SM16716 RGB LED controller (+0k7 code)
#undef USE_SM2135 // Disable support for SM2135 RGBCW led control as used in Action LSC (+0k6 code)
#undef USE_SONOFF_L1 // Disable support for Sonoff L1 led control
#undef USE_COUNTER // Disable counters
#define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices
#undef USE_DS18x20 // Disable DS18x20 sensor
#undef USE_I2C // Disable all I2C sensors and devices
#undef USE_SPI // Disable all SPI devices
#undef USE_DISPLAY // Disable Display support
#undef USE_MHZ19 // Disable support for MH-Z19 CO2 sensor
#undef USE_SENSEAIR // Disable support for SenseAir K30, K70 and S8 CO2 sensor
#undef USE_PMS5003 // Disable support for PMS5003 and PMS7003 particle concentration sensor
#undef USE_NOVA_SDS // Disable support for SDS011 and SDS021 particle concentration sensor
#undef USE_SERIAL_BRIDGE // Disable support for software Serial Bridge
#undef USE_MP3_PLAYER // Disable DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop
#undef USE_AZ7798 // Disable support for AZ-Instrument 7798 CO2 datalogger
#undef USE_PN532_HSU // Disable support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem)
#undef USE_RDM6300 // Disable support for RDM6300 125kHz RFID Reader (+0k8)
#undef USE_IBEACON // Disable support for bluetooth LE passive scan of ibeacon devices (uses HM17 module)
#undef USE_ENERGY_SENSOR // Disable energy sensors
#undef USE_PZEM004T // Disable PZEM004T energy sensor
#undef USE_PZEM_AC // Disable PZEM014,016 Energy monitor
#undef USE_PZEM_DC // Disable PZEM003,017 Energy monitor
#undef USE_MCP39F501 // Disable MCP39F501 Energy monitor as used in Shelly 2
#undef USE_SDM120 // Disable support for Eastron SDM120-Modbus energy meter
#undef USE_SDM630 // Disable support for Eastron SDM630-Modbus energy monitor (+0k6 code)
#undef USE_DDS2382 // Disable support for Hiking DDS2382 Modbus energy monitor (+0k6 code)
#undef USE_DDSU666 // Disable support for Chint DDSU666 Modbus energy monitor (+0k6 code)
#undef USE_SOLAX_X1 // Disable support for Solax X1 series Modbus log info (+3k1 code)
#undef USE_DHT // Disable support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor
#undef USE_MAX31855 // Disable MAX31855 K-Type thermocouple sensor using softSPI
#undef USE_MAX31865 // Disable support for MAX31865 RTD sensors using softSPI
#undef USE_IR_REMOTE // Disable IR driver
#undef USE_SR04 // Disable support for for HC-SR04 ultrasonic devices
#undef USE_TM1638 // Disable support for TM1638 switches copying Switch1 .. Switch8
#undef USE_HX711 // Disable support for HX711 load cell
#undef USE_TX20_WIND_SENSOR // Disable support for La Crosse TX20 anemometer
#undef USE_RC_SWITCH // Disable support for RF transceiver using library RcSwitch
#undef USE_RF_SENSOR // Disable support for RF sensor receiver (434MHz or 868MHz) (+0k8 code)
#undef USE_HRE // Disable support for Badger HR-E Water Meter (+1k4 code)
#undef USE_A4988_STEPPER // Disable support for A4988_Stepper
#undef DEBUG_THEO // Disable debug code
#undef USE_DEBUG_DRIVER // Disable debug code
#endif // FIRMWARE_MINIMAL
/*********************************************************************************************\
* Mandatory defines satisfying possible disabled defines
\*********************************************************************************************/
#ifndef USE_WPS // See https://github.com/esp8266/Arduino/pull/4889
#undef NO_EXTRA_4K_HEAP // Allocate 4k heap for WPS in ESP8166/Arduino core v2.4.2 (was always allocated in previous versions)
#endif
#ifndef USE_SONOFF_RF
#undef USE_RF_FLASH // Disable RF firmware flash when SOnoff Rf is disabled
#endif
#ifndef SWITCH_MODE
#define SWITCH_MODE TOGGLE // TOGGLE, FOLLOW or FOLLOW_INV (the wall switch state)
#endif
#ifndef MQTT_FINGERPRINT1
// Set an all-zeros default fingerprint to activate auto-learning on first connection (AWS IoT)
#define MQTT_FINGERPRINT1 "00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00"
#endif
#ifndef MQTT_FINGERPRINT2
#define MQTT_FINGERPRINT2 "A5 02 FF 13 99 9F 8B 39 8E F1 83 4F 11 23 65 0B 32 36 FC 07"
#endif
#ifndef WS2812_LEDS
#define WS2812_LEDS 30 // [Pixels] Number of LEDs
#endif
#ifndef MQTT_MAX_PACKET_SIZE
#define MQTT_MAX_PACKET_SIZE 1000 // Bytes
#endif
#ifndef MQTT_KEEPALIVE
#define MQTT_KEEPALIVE 30 // Seconds
#endif
#ifndef MQTT_TIMEOUT
#define MQTT_TIMEOUT 10000 // milli seconds
#endif
#ifndef MQTT_CLEAN_SESSION
#define MQTT_CLEAN_SESSION 1 // 0 = No clean session, 1 = Clean session (default)
#endif
#ifndef MESSZ
//#define MESSZ 893 // Max number of characters in JSON message string (Hass discovery and nice MQTT_MAX_PACKET_SIZE = 1000)
#define MESSZ (MQTT_MAX_PACKET_SIZE -TOPSZ -7) // Max number of characters in JSON message string
#endif
//#include <core_version.h> // Arduino_Esp8266 version information (ARDUINO_ESP8266_RELEASE and ARDUINO_ESP8266_RELEASE_2_3_0)
#ifndef ARDUINO_ESP8266_RELEASE
#define ARDUINO_ESP8266_RELEASE "STAGE"
#endif
#ifdef ARDUINO_ESP8266_RELEASE_2_3_0 // Disable not supported features in core 2.3.0
#undef USE_MQTT_TLS_CA_CERT
#endif
#ifdef DEBUG_TASMOTA_CORE
#define DEBUG_CORE_LOG(...) AddLog_Debug(__VA_ARGS__)
#else
#define DEBUG_CORE_LOG(...)
#endif
#ifdef DEBUG_TASMOTA_DRIVER
#define DEBUG_DRIVER_LOG(...) AddLog_Debug(__VA_ARGS__)
#else
#define DEBUG_DRIVER_LOG(...)
#endif
#ifdef DEBUG_TASMOTA_SENSOR
#define DEBUG_SENSOR_LOG(...) AddLog_Debug(__VA_ARGS__)
#else
#define DEBUG_SENSOR_LOG(...)
#endif
#endif // _SONOFF_POST_H_