mirror of https://github.com/arendst/Tasmota.git
92 lines
2.5 KiB
Python
92 lines
2.5 KiB
Python
#-------------------------------------------------------------
|
|
- Specialized driver for AXP192 of M5StickC
|
|
-------------------------------------------------------------#
|
|
class AXP192_M5StickC : AXP192
|
|
def init()
|
|
super(self, AXP192).init()
|
|
if self.wire
|
|
# Disable vbus hold limit
|
|
self.write8(0x30, 0x80)
|
|
|
|
# lcd backlight voltage was set to 2.80v
|
|
self.set_lcd_voltage(2800)
|
|
|
|
# set LDO3 3.0V TFT
|
|
self.set_ldo_voltage(3, 3000)
|
|
|
|
# Set ADC sample rate to 200hz
|
|
self.write8(0x84, 0xF2)
|
|
|
|
# set charging current to 100mA
|
|
self.set_chg_current(0) # 0 = 100mA
|
|
|
|
# esp32 power voltage was set to 3.3v
|
|
self.set_esp_voltage(3300)
|
|
|
|
# PEK key parameter setting
|
|
# Current:
|
|
# Boot time setting = 512ms
|
|
# Long press time setting = 1s
|
|
# Automatic shutdown function setting when the key duration is longer than the shutdown duration = turn on
|
|
# PWROK signal delay after power on = 64ms
|
|
# Shutdown duration setting = 4s
|
|
self.write8(0x36, 0x4C)
|
|
|
|
# Mic GPIO0 - floating
|
|
self.write8(0x90, 0x07)
|
|
|
|
# enable LDO2, LDO3, DCDC1, DCDC3
|
|
self.set_ldo_enable(2, true)
|
|
self.set_ldo_enable(3, true)
|
|
self.set_dcdc_enable(1, true)
|
|
self.set_dcdc_enable(3, true)
|
|
|
|
# Set temperature protection
|
|
self.write8(0x39, 0xFC)
|
|
|
|
# Enable RTC BAT charge
|
|
self.write8(0x35, 0xA2)
|
|
# Write1Byte(0x35, 0xa2 & (disableRTC ? 0x7F : 0xFF));
|
|
|
|
# Enable bat detection
|
|
self.write8(0x32, 0x46)
|
|
|
|
# Set Power off voltage 3.0v
|
|
self.write8(0x31, self.read8(0x31) & 0xF8 | 0x04)
|
|
|
|
# ADC all-on
|
|
# Bit 7: Battery voltage ADC enable
|
|
# Bit 6: Battery current ADC enable
|
|
# Bit 5: ACIN voltage ADC enable
|
|
# Bit 4: ACIN current ADC enable
|
|
# Bit 3: VBUS voltage ADC enable
|
|
# Bit 2: VBUS current ADC enable
|
|
# Bit 1: APS voltage ADC enable
|
|
# Bit 0: TS pin ADC function enable
|
|
self.write8(0x82, 0xFF)
|
|
end
|
|
end
|
|
|
|
# set ESP voltage on DCDC1
|
|
def set_esp_voltage(voltage)
|
|
if voltage >= 3000 && voltage <= 3400
|
|
self.set_dc_voltage(1, voltage)
|
|
end
|
|
end
|
|
|
|
# set LCD backlight voltage on DCDC3
|
|
def set_lcd_voltage(voltage)
|
|
if voltage < 2500 voltage = 2500 end
|
|
if voltage > 3300 voltage = 3300 end
|
|
self.set_ldo_voltage(2, voltage)
|
|
end
|
|
|
|
# LCD Controller Reset pin
|
|
def set_lcd_reset(state)
|
|
self.set_ldo_enable(3, state)
|
|
end
|
|
end
|
|
|
|
axp = AXP192_M5StickC()
|
|
tasmota.add_driver(axp)
|