mirror of https://github.com/arendst/Tasmota.git
115 lines
5.0 KiB
C++
115 lines
5.0 KiB
C++
/* IRremoteESP8266: IRsendProntoDemo
|
|
* Copyright 2017 David Conran
|
|
*
|
|
* Demonstrates sending Pronto codes with IRsend.
|
|
*
|
|
* Version 1.0 June, 2017
|
|
*
|
|
* An IR LED circuit *MUST* be connected to ESP8266 pin 4 (D2), unless you
|
|
* change the kIrLed value below.
|
|
*
|
|
* TL;DR: The IR LED needs to be driven by a transistor for a good result.
|
|
*
|
|
* Suggested circuit:
|
|
* https://github.com/crankyoldgit/IRremoteESP8266/wiki#ir-sending
|
|
*
|
|
* Common mistakes & tips:
|
|
* * Don't just connect the IR LED directly to the pin, it won't
|
|
* have enough current to drive the IR LED effectively.
|
|
* * Make sure you have the IR LED polarity correct.
|
|
* See: https://learn.sparkfun.com/tutorials/polarity/diode-and-led-polarity
|
|
* * Typical digital camera/phones can be used to see if the IR LED is flashed.
|
|
* Replace the IR LED with a normal LED if you don't have a digital camera
|
|
* when debugging.
|
|
* * Avoid using the following pins unless you really know what you are doing:
|
|
* * Pin 0/D3: Can interfere with the boot/program mode & support circuits.
|
|
* * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will interfere.
|
|
* * Pin 3/RX/RXD0: Any serial transmissions to the ESP8266 will interfere.
|
|
* * ESP-01 modules are tricky. We suggest you use a module with more GPIOs
|
|
* for your first time. e.g. ESP-12 etc.
|
|
*/
|
|
|
|
#include <Arduino.h>
|
|
#include <IRremoteESP8266.h>
|
|
#include <IRsend.h>
|
|
|
|
const uint16_t kIrLed = 4; // ESP8266 GPIO pin to use. Recommended: 4 (D2).
|
|
|
|
IRsend irsend(kIrLed); // Set the GPIO to be used to sending the message.
|
|
|
|
// Panasonic Plasma TV Descrete code (Power On).
|
|
// Acquired from:
|
|
// https://irdb.globalcache.com/
|
|
// e.g.
|
|
// 0000 006D 0000 0022 00ac 00ac 0016 0040 0016 0040 0016 0040 0016 0015 0016
|
|
// 0015 0016 0015 0016 0015 0016 0015 0016 0040 0016 0040 0016 0040 0016 0015
|
|
// 0016 0015 0016 0015 0016 0015 0016 0015 0016 0040 0016 0015 0016 0015 0016
|
|
// 0040 0016 0040 0016 0015 0016 0015 0016 0040 0016 0015 0016 0040 0016 0040
|
|
// 0016 0015 0016 0015 0016 0040 0016 0040 0016 0015 0016 071c
|
|
//
|
|
// Or the equiv. of sendSamsung(0xE0E09966);
|
|
uint16_t samsungProntoCode[72] = {
|
|
0x0000, 0x006D, 0x0000, 0x0022,
|
|
0x00ac, 0x00ac, 0x0016, 0x0040, 0x0016, 0x0040, 0x0016, 0x0040,
|
|
0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0015,
|
|
0x0016, 0x0015, 0x0016, 0x0040, 0x0016, 0x0040, 0x0016, 0x0040,
|
|
0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0015,
|
|
0x0016, 0x0015, 0x0016, 0x0040, 0x0016, 0x0015, 0x0016, 0x0015,
|
|
0x0016, 0x0040, 0x0016, 0x0040, 0x0016, 0x0015, 0x0016, 0x0015,
|
|
0x0016, 0x0040, 0x0016, 0x0015, 0x0016, 0x0040, 0x0016, 0x0040,
|
|
0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0040, 0x0016, 0x0040,
|
|
0x0016, 0x0015, 0x0016, 0x071c
|
|
};
|
|
|
|
// Panasonic Plasma TV Descrete code (Power On).
|
|
// Acquired from:
|
|
// ftp://ftp.panasonic.com/pub/panasonic/drivers/monitors/Discrete-remote-control-codesProntoCCFformat.pdf
|
|
// e.g.
|
|
// 0000 0071 0000 0032 0080 003F 0010 0010 0010 0030 0010 0010 0010 0010 0010
|
|
// 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010
|
|
// 0010 0010 0010 0030 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010
|
|
// 0010 0010 0010 0010 0010 0010 0010 0010 0030 0010 0010 0010 0010 0010 0010
|
|
// 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0030 0010
|
|
// 0030 0010 0030 0010 0030 0010 0030 0010 0010 0010 0010 0010 0010 0010 0030
|
|
// 0010 0030 0010 0030 0010 0030 0010 0030 0010 0010 0010 0030 0010 0A98
|
|
//
|
|
// Or the equiv. of sendPanasonic64(0x400401007C7D);
|
|
uint16_t panasonicProntoCode[104] = {
|
|
0x0000, 0x0071, 0x0000, 0x0032,
|
|
0x0080, 0x003F, 0x0010, 0x0010, 0x0010, 0x0030, 0x0010, 0x0010,
|
|
0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
|
|
0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
|
|
0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0030, 0x0010, 0x0010,
|
|
0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
|
|
0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
|
|
0x0010, 0x0030, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
|
|
0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
|
|
0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0030, 0x0010, 0x0030,
|
|
0x0010, 0x0030, 0x0010, 0x0030, 0x0010, 0x0030, 0x0010, 0x0010,
|
|
0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0030, 0x0010, 0x0030,
|
|
0x0010, 0x0030, 0x0010, 0x0030, 0x0010, 0x0030, 0x0010, 0x0010,
|
|
0x0010, 0x0030, 0x0010, 0x0A98};
|
|
|
|
void setup() {
|
|
irsend.begin();
|
|
#if defined(ESP8266)
|
|
Serial.begin(115200, SERIAL_8N1, SERIAL_TX_ONLY);
|
|
#else // ESP8266
|
|
Serial.begin(115200, SERIAL_8N1);
|
|
#endif // ESP8266
|
|
}
|
|
|
|
void loop() {
|
|
#if SEND_PRONTO
|
|
Serial.println("Sending a Samsung TV 'on' command.");
|
|
irsend.sendPronto(samsungProntoCode, 72);
|
|
delay(2000);
|
|
Serial.println("Sending a Panasonic Plasma TV 'on' command.");
|
|
irsend.sendPronto(panasonicProntoCode, 104);
|
|
delay(2000);
|
|
#else // SEND_PRONTO
|
|
Serial.println("Can't send because SEND_PRONTO has been disabled.");
|
|
delay(10000);
|
|
#endif // SEND_PRONTO
|
|
}
|