Tasmota/sonoff/user_config.h

169 lines
13 KiB
C

/*********************************************************************************************\
* User specific configuration parameters
*
* ATTENTION: Changes to most PARAMETER defines will only override flash settings if you change
* define CFG_HOLDER.
* Most parameters can be changed online using commands via MQTT, WebConsole or serial
*
* Corresponding MQTT/Serial/Console commands in [brackets]
\*********************************************************************************************/
// -- Project -------------------------------------
#define PROJECT "sonoff" // PROJECT is used as the default topic delimiter and OTA file name
// As an IDE restriction it needs to be the same as the main .ino file
#define CFG_HOLDER 0x20161209 // [Reset 1] Change this value to load following default configuration parameters
#define SAVE_DATA 1 // [SaveData] Save changed parameters to Flash (0 = disable, 1 - 3600 seconds)
#define SAVE_STATE 1 // [SaveState] Save changed power state to Flash (0 = disable, 1 = enable)
// -- Wifi ----------------------------------------
#define WIFI_IP_ADDRESS "0.0.0.0" // [IpAddress1] Set to 0.0.0.0 for using DHCP or IP address
#define WIFI_GATEWAY "192.168.2.254" // {IpAddress2] If not using DHCP set Gateway IP address
#define WIFI_SUBNETMASK "255.255.255.0" // [IpAddress3] If not using DHCP set Network mask
#define WIFI_DNS "192.168.2.27" // [IpAddress4] If not using DHCP set DNS IP address (might be equal to WIFI_GATEWAY)
#define STA_SSID1 "indebuurt1" // [Ssid1] Wifi SSID
#define STA_PASS1 "VnsqrtnrsddbrN" // [Password1] Wifi password
#define STA_SSID2 "indebuurt2" // [Ssid2] Optional alternate AP Wifi SSID
#define STA_PASS2 "VnsqrtnrsddbrN" // [Password2] Optional alternate AP Wifi password
#define WIFI_CONFIG_TOOL WIFI_WPSCONFIG // [WifiConfig] Default tool if wifi fails to connect
// (WIFI_RESTART, WIFI_SMARTCONFIG, WIFI_MANAGER, WIFI_WPSCONFIG, WIFI_RETRY)
// -- Syslog --------------------------------------
#define SYS_LOG_HOST "domus1" // [LogHost] (Linux) syslog host
#define SYS_LOG_PORT 514 // [LogPort] default syslog UDP port
#define SYS_LOG_LEVEL LOG_LEVEL_NONE // [SysLog]
#define SERIAL_LOG_LEVEL LOG_LEVEL_INFO // [SerialLog]
#define WEB_LOG_LEVEL LOG_LEVEL_INFO // [WebLog]
// -- Ota -----------------------------------------
#define OTA_URL "http://domus1:80/api/arduino/" PROJECT ".ino.bin" // [OtaUrl]
// -- MQTT ----------------------------------------
#define MQTT_USE 1 // [Mqtt] Select default MQTT use (0 = Off, 1 = On)
// !!! TLS uses a LOT OF MEMORY (20k) so be careful to enable other options at the same time !!!
//#define USE_MQTT_TLS // EXPERIMENTAL Use TLS for MQTT connection (+53k code, +20k mem) - Disable by //
// Needs Fingerprint, TLS Port, UserId and Password
#ifdef USE_MQTT_TLS
#define MQTT_HOST "m20.cloudmqtt.com" // [MqttHost]
#define MQTT_FINGERPRINT "A5 02 FF 13 99 9F 8B 39 8E F1 83 4F 11 23 65 0B 32 36 FC 07" // [MqttFingerprint]
#define MQTT_PORT 20123 // [MqttPort] MQTT TLS port
#define MQTT_USER "cloudmqttuser" // [MqttUser] Mandatory user
#define MQTT_PASS "cloudmqttpassword" // [MqttPassword] Mandatory password
#else
#define MQTT_HOST "domus1" // [MqttHost]
#define MQTT_PORT 1883 // [MqttPort] MQTT port (10123 on CloudMQTT)
#define MQTT_USER "DVES_USER" // [MqttUser] Optional user
#define MQTT_PASS "DVES_PASS" // [MqttPassword] Optional password
#endif
#define MQTT_CLIENT_ID "DVES_%06X" // [MqttClient] Also fall back topic using Chip Id = last 6 characters of MAC address
#define SUB_PREFIX "cmnd" // [Prefix1] Sonoff devices subscribe to:- SUB_PREFIX/MQTT_TOPIC and SUB_PREFIX/MQTT_GRPTOPIC
#define PUB_PREFIX "stat" // [Prefix2] Sonoff devices publish to:- PUB_PREFIX/MQTT_TOPIC
#define PUB_PREFIX2 "tele" // [Prefix3] Sonoff devices publish telemetry data to:- PUB_PREFIX2/MQTT_TOPIC/UPTIME, POWER/LIGHT and TIME
// May be named the same as PUB_PREFIX
#define MQTT_TOPIC PROJECT // [Topic] (unique) MQTT device topic
#define MQTT_GRPTOPIC "sonoffs" // [GroupTopic] MQTT Group topic
#define MQTT_BUTTON_RETAIN 0 // [ButtonRetain] Button may send retain flag (0 = off, 1 = on)
#define MQTT_POWER_RETAIN 0 // [PowerRetain] Power status message may send retain flag (0 = off, 1 = on)
#define MQTT_SWITCH_RETAIN 0 // [SwitchRetain] Switch may send retain flag (0 = off, 1 = on)
#define MQTT_STATUS_OFF "OFF" // [StateText1] Command or Status result when turned off (needs to be a string like "0" or "Off")
#define MQTT_STATUS_ON "ON" // [StateText2] Command or Status result when turned on (needs to be a string like "1" or "On")
#define MQTT_CMND_TOGGLE "TOGGLE" // [StateText3] Command to send when toggling (needs to be a string like "2" or "Toggle")
// -- MQTT - Telemetry ----------------------------
#define TELE_PERIOD 300 // [TelePeriod] Telemetry (0 = disable, 10 - 3600 seconds)
// -- MQTT - Domoticz -----------------------------
#define USE_DOMOTICZ // Enable Domoticz (+7k code, +0.3k mem) - Disable by //
#define DOMOTICZ_IN_TOPIC "domoticz/in" // [DomoticzInTopic]
#define DOMOTICZ_OUT_TOPIC "domoticz/out" // [DomoticzOutTopic]
#define DOMOTICZ_UPDATE_TIMER 0 // [DomoticzUpdateTimer] Send relay status (0 = disable, 1 - 3600 seconds) (Optional)
// -- HTTP ----------------------------------------
#define USE_WEBSERVER // Enable web server and wifi manager (+62k code, +8k mem) - Disable by //
#define WEB_SERVER 2 // [WebServer] Web server (0 = Off, 1 = Start as User, 2 = Start as Admin)
#define WEB_PORT 80 // Web server Port for User and Admin mode
#define WEB_USERNAME "admin" // Web server Admin mode user name
#define WEB_PASSWORD "" // [WebPassword] Web server Admin mode Password for WEB_USERNAME (empty string = Disable)
#define FRIENDLY_NAME "Sonoff" // [FriendlyName] Friendlyname up to 32 characters used by webpages and Alexa
#define USE_EMULATION // Enable Belkin WeMo and Hue Bridge emulation for Alexa (+11k code, +2k mem)
#define EMULATION EMUL_NONE // [Emulation] Select Belkin WeMo (single relay/light) or Hue Bridge emulation (multi relay/light) (EMUL_NONE, EMUL_WEMO or EMUL_HUE)
// -- mDNS ----------------------------------------
#define USE_DISCOVERY // Enable mDNS for the following services (+8k code, +0.3k mem) - Disable by //
#define WEBSERVER_ADVERTISE // Provide access to webserver by name <Hostname>.local/
#define MQTT_HOST_DISCOVERY // Find MQTT host server (overrides MQTT_HOST if found)
// -- Time - Up to three NTP servers in your region
#define NTP_SERVER1 "pool.ntp.org" // [NtpServer1] Select first NTP server by name or IP address (129.250.35.250)
#define NTP_SERVER2 "nl.pool.ntp.org" // [NtpServer2] Select second NTP server by name or IP address (5.39.184.5)
#define NTP_SERVER3 "0.nl.pool.ntp.org" // [NtpServer3] Select third NTP server by name or IP address (93.94.224.67)
// -- Time - Start Daylight Saving Time and timezone offset from UTC in minutes
#define TIME_DST Last, Sun, Mar, 2, +120 // Last sunday in march at 02:00 +120 minutes
// -- Time - Start Standard Time and timezone offset from UTC in minutes
#define TIME_STD Last, Sun, Oct, 3, +60 // Last sunday in october 02:00 +60 minutes
// -- Application ---------------------------------
#define APP_TIMEZONE 1 // [Timezone] +1 hour (Amsterdam) (-12 .. 12 = hours from UTC, 99 = use TIME_DST/TIME_STD)
#define APP_LEDSTATE LED_POWER // [LedState] Function of led (LED_OFF, LED_POWER, LED_MQTTSUB, LED_POWER_MQTTSUB, LED_MQTTPUB, LED_POWER_MQTTPUB, LED_MQTT, LED_POWER_MQTT)
#define APP_PULSETIME 0 // [PulseTime] Time in 0.1 Sec to turn off power for relay 1 (0 = disabled)
#define APP_POWERON_STATE 3 // [PowerOnState] Power On Relay state (0 = Off, 1 = On, 2 = Toggle Saved state, 3 = Saved state)
#define APP_BLINKTIME 10 // [BlinkTime] Time in 0.1 Sec to blink/toggle power for relay 1
#define APP_BLINKCOUNT 10 // [BlinkCount] Number of blinks (0 = 32000)
#define APP_SLEEP 0 // [Sleep] Sleep time to lower energy consumption (0 = Off, 1 - 250 mSec)
#define SWITCH_MODE TOGGLE // [SwitchMode] TOGGLE, FOLLOW, FOLLOW_INV, PUSHBUTTON or PUSHBUTTON_INV (the wall switch state)
#define WS2812_LEDS 30 // [Pixels] Number of WS2812 LEDs to start with
#define TEMP_CONVERSION 0 // Convert temperature to (0 = Celsius or 1 = Fahrenheit)
#define TEMP_RESOLUTION 1 // Maximum number of decimals (0 - 3) showing sensor Temperature
#define HUMIDITY_RESOLUTION 1 // Maximum number of decimals (0 - 3) showing sensor Humidity
#define PRESSURE_RESOLUTION 1 // Maximum number of decimals (0 - 3) showing sensor Pressure
#define ENERGY_RESOLUTION 3 // Maximum number of decimals (0 - 5) showing energy usage in kWh
// -- Sensor code selection -----------------------
#define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices
//#define USE_DS18x20 // Optional using OneWire library for multiple DS18B20 and/or DS18S20 (+2k code)
#define USE_I2C // I2C using library wire (+10k code, 0.2k mem) - Disable by //
#define USE_BH1750 // Add I2C code for BH1750 sensor
#define USE_BMP // Add I2C code for BMP/BME280 sensor
#define USE_HTU // Add I2C code for HTU21/SI7013/SI7020/SI7021 sensor
#define USE_SHT // Add I2C emulating code for SHT1X sensor
#define USE_IR_REMOTE // Send IR remote commands using library IRremoteESP8266 and ArduinoJson (+3k code, 0.3k mem)
// #define USE_IR_HVAC // Support for HVAC system using IR (+2k code)
#define USE_WS2812 // WS2812 Led string using library NeoPixelBus (+8k code, +1k mem) - Disable by //
#define USE_WS2812_CTYPE 1 // WS2812 Color type (0 - RGB, 1 - GRB)
// #define USE_WS2812_DMA // DMA supports only GPIO03 (= Serial TXD) (+1k mem)
// When USE_WS2812_DMA is enabled expect Exceptions on Pow
/*********************************************************************************************\
* Compile a minimal version if upgrade memory gets tight ONLY TO BE USED FOR UPGRADE STEP 1!
* To be used as step 1 during upgrade.
* Step 2 is re-compile with option BE_MINIMAL commented out.
* !!! Needed for next release of Arduino/ESP8266 (+22k code, +2k mem) !!!
\*********************************************************************************************/
//#define BE_MINIMAL // Minimal version if upgrade memory gets tight (-45k code, -2k mem)
/*********************************************************************************************\
* No user configurable items below
\*********************************************************************************************/
#if defined(USE_MQTT_TLS) && defined(USE_WEBSERVER)
#error "Select either USE_MQTT_TLS or USE_WEBSERVER as there is just not enough memory to play with"
#endif
#if (ARDUINO < 10610)
#error "This software is supported with Arduino IDE starting from 1.6.10 and ESP8266 Release 2.3.0"
#endif