mirror of https://github.com/arendst/Tasmota.git
797 lines
50 KiB
C++
797 lines
50 KiB
C++
/*
|
|
xnrg_23_ade7880.ino - ADE7880 energy sensor support for Tasmota
|
|
|
|
SPDX-FileCopyrightText: 2022 Theo Arends and AndreKR
|
|
|
|
SPDX-License-Identifier: GPL-3.0-only
|
|
*/
|
|
|
|
#ifdef USE_I2C
|
|
#ifdef USE_ENERGY_SENSOR
|
|
#ifdef USE_ADE7880
|
|
/*********************************************************************************************\
|
|
* ADE7880 - Energy used in Shelly 3EM
|
|
*
|
|
* {"NAME":"Shelly 3EM","GPIO":[1,1,288,1,32,8065,0,0,640,8064,608,224,8096,0],"FLAG":0,"BASE":18}
|
|
*
|
|
* Based on datasheet from https://www.analog.com/en/products/ade7880.html Rev.C
|
|
*
|
|
* I2C Address: 0x38
|
|
*********************************************************************************************
|
|
* - ATTENTION Before installing Tasmota retrieve the calibration data from the Shelly 3EM:
|
|
* - Download file calib.dat from your configured shelly 3EM http://<shelly3em_ip_address>/calib.dat
|
|
* - Search your Shelly 3EM firmware dump for calib.dat
|
|
* - Edit the file to become a single line. Notice the removal of unneeded data to make the string as short as possible:
|
|
* {"rms":{"current_a":3166385,"current_b":3125691,"current_c":3131983,"current_s":1756557,"voltage_a":-767262,"voltage_b":-763439,"voltage_c":-749854},"angles":{"angle0":180,"angle1":176,"angle2":176},"powers":{"totactive": {"a":-1345820,"b":-1347328,"c":-1351979}},"freq":0}
|
|
* - Install Tasmota and use the above template.
|
|
* - In addition to possible rules add a rule containing the calib.dat string from above like:
|
|
* rule3 on file#calib.dat do {"rms":{"current_a":3166385,"current_b":3125691,"current_c":3131983,"current_s":1756557,"voltage_a":-767262,"voltage_b":-763439,"voltage_c":-749854},"angles":{"angle0":180,"angle1":176,"angle2":176},"powers":{"totactive": {"a":-1345820,"b":-1347328,"c":-1351979}},"freq":0} endon
|
|
* - Restart Tasmota and obeserve that the results seem calibrated as Tasmota now uses the information from calib.dat
|
|
\*********************************************************************************************/
|
|
|
|
#define XNRG_23 23
|
|
#define XI2C_65 65 // See I2CDEVICES.md
|
|
|
|
#define ADE7880_ADDR 0x38
|
|
|
|
/*********************************************************************************************/
|
|
|
|
#define ADE7880_MORE_REGS // Add Neutral Current information
|
|
|
|
//#define ADE7880_DEBUG
|
|
//#define ADE7880_PROFILING
|
|
|
|
#define ADE7880_WATCHDOG 5 // Allow x seconds of missed interrupts before reinit
|
|
|
|
// Default calibration parameters can be overridden by a rule as documented above.
|
|
#define ADE7880_FREQ_INIT 0 // Connected to networks with fundamental frequencies between 55 Hz and 66 Hz (1). Default 45 Hz to 55 Hz (0).
|
|
#define ADE7880_AIGAIN_INIT 3166385 // rms, current_a
|
|
#define ADE7880_BIGAIN_INIT 3125691 // rms, current_b
|
|
#define ADE7880_CIGAIN_INIT 3131983 // rms, current_c
|
|
#define ADE7880_NIGAIN_INIT 1756557 // rms, current_s !!
|
|
#define ADE7880_AVGAIN_INIT -767262 // rms, voltage_a
|
|
#define ADE7880_BVGAIN_INIT -763439 // rms, voltage_b
|
|
#define ADE7880_CVGAIN_INIT -749854 // rms, voltage_c
|
|
#define ADE7880_APHCAL_INIT 180 // angles, angle0
|
|
#define ADE7880_BPHCAL_INIT 176 // angles, angle1
|
|
#define ADE7880_CPHCAL_INIT 176 // angles, angle2
|
|
#define ADE7880_APGAIN_INIT -1345820 // powers, totactive, a
|
|
#define ADE7880_BPGAIN_INIT -1347328 // powers, totactive, b
|
|
#define ADE7880_CPGAIN_INIT -1351979 // powers, totactive, c
|
|
|
|
enum Ade7880DspRegisters {
|
|
// Register Name Addres R/W Bt CommBln Ty Default Description
|
|
// ---------------------------- ------ --- -- ------- -- ---------- --------------------------------------------------------------------
|
|
ADE7880_AIGAIN = 0x4380, // 0x4380 R/W 24 32 ZPSE S 0x000000 Phase A current gain adjust.
|
|
ADE7880_AVGAIN, // 0x4381 R/W 24 32 ZPSE S 0x000000 Phase A voltage gain adjust.
|
|
ADE7880_BIGAIN, // 0x4382 R/W 24 32 ZPSE S 0x000000 Phase B current gain adjust.
|
|
ADE7880_BVGAIN, // 0x4383 R/W 24 32 ZPSE S 0x000000 Phase B voltage gain adjust.
|
|
ADE7880_CIGAIN, // 0x4384 R/W 24 32 ZPSE S 0x000000 Phase C current gain adjust.
|
|
ADE7880_CVGAIN, // 0x4385 R/W 24 32 ZPSE S 0x000000 Phase C voltage gain adjust.
|
|
ADE7880_NIGAIN, // 0x4386 R/W 24 32 ZPSE S 0x000000 Neutral current gain adjust.
|
|
ADE7880_DICOEFF = 0x4388, // 0x4388 R/W 24 32 ZPSE S 0x0000000 Register used in the digital integrator algorithm. If the integrator is turned on, it must be set at 0xFF8000. In practice, it is transmitted as 0xFFF8000.
|
|
ADE7880_APGAIN, // 0x4389 R/W 24 32 ZPSE S 0x000000 Phase A power gain adjust.
|
|
ADE7880_AWATTOS, // 0x438A R/W 24 32 ZPSE S 0x000000 Phase A total active power offset adjust.
|
|
ADE7880_BPGAIN, // 0x438B R/W 24 32 ZPSE S 0x000000 Phase B power gain adjust.
|
|
ADE7880_BWATTOS, // 0x438C R/W 24 32 ZPSE S 0x000000 Phase B total active power offset adjust.
|
|
ADE7880_CPGAIN, // 0x438D R/W 24 32 ZPSE S 0x000000 Phase C power gain adjust.
|
|
ADE7880_CWATTOS, // 0x438E R/W 24 32 ZPSE S 0x000000 Phase C total active power offset adjust.
|
|
ADE7880_AIRMSOS, // 0x438F R/W 24 32 ZPSE S 0x000000 Phase A current rms offset.
|
|
ADE7880_AVRMSOS, // 0x4390 R/W 24 32 ZPSE S 0x000000 Phase A voltage rms offset.
|
|
ADE7880_BIRMSOS, // 0x4391 R/W 24 32 ZPSE S 0x000000 Phase B current rms offset.
|
|
ADE7880_BVRMSOS, // 0x4392 R/W 24 32 ZPSE S 0x000000 Phase B voltage rms offset.
|
|
ADE7880_CIRMSOS, // 0x4393 R/W 24 32 ZPSE S 0x000000 Phase C current rms offset.
|
|
ADE7880_CVRMSOS, // 0x4394 R/W 24 32 ZPSE S 0x000000 Phase C voltage rms offset.
|
|
ADE7880_NIRMSOS, // 0x4395 R/W 24 32 ZPSE S 0x000000 Neutral current rms offset.
|
|
ADE7880_HPGAIN = 0x4398, // 0x4398 R/W 24 32 ZPSE S 0x000000 Harmonic powers gain adjust.
|
|
ADE7880_ISUMLVL, // 0x4399 R/W 24 32 ZPSE S 0x000000 Threshold used in comparison between the sum of phase currents and the neutral current.
|
|
ADE7880_VLEVEL = 0x439F, // 0x439F R/W 28 32 ZP S 0x0000000 Register used in the algorithm that computes the fundamental active and reactive powers. Set this register according to Equation 22 for proper functioning of fundamental powers and harmonic computations.
|
|
ADE7880_AFWATTOS = 0x43A2, // 0x43A2 R/W 24 32 ZPSE S 0x000000 Phase A fundamental active power offset adjust.
|
|
ADE7880_BFWATTOS, // 0x43A3 R/W 24 32 ZPSE S 0x000000 Phase B fundamental active power offset adjust.
|
|
ADE7880_CFWATTOS, // 0x43A4 R/W 24 32 ZPSE S 0x000000 Phase C fundamental active power offset adjust.
|
|
ADE7880_AFVAROS, // 0x43A5 R/W 24 32 ZPSE S 0x000000 Phase A fundamental reactive power offset adjust.
|
|
ADE7880_BFVAROS, // 0x43A6 R/W 24 32 ZPSE S 0x000000 Phase B fundamental reactive power offset adjust.
|
|
ADE7880_CFVAROS, // 0x43A7 R/W 24 32 ZPSE S 0x000000 Phase C fundamental reactive power offset adjust.
|
|
ADE7880_AFIRMSOS, // 0x43A8 R/W 24 32 ZPSE S 0x000000 Phase A fundamental current rms offset.
|
|
ADE7880_BFIRMSOS, // 0x43A9 R/W 24 32 ZPSE S 0x000000 Phase B fundamental current rms offset.
|
|
ADE7880_CFIRMSOS, // 0x43AA R/W 24 32 ZPSE S 0x000000 Phase C fundamental current rms offset.
|
|
ADE7880_AFVRMSOS, // 0x43AB R/W 24 32 ZPSE S 0x000000 Phase A fundamental voltage rms offset.
|
|
ADE7880_BFVRMSOS, // 0x43AC R/W 24 32 ZPSE S 0x000000 Phase B fundamental voltage rms offset.
|
|
ADE7880_CFVRMSOS, // 0x43AD R/W 24 32 ZPSE S 0x000000 Phase C fundamental voltage rms offset.
|
|
ADE7880_HXWATTOS, // 0x43AE R/W 24 32 ZPSE S 0x000000 Active power offset adjust on harmonic X (see Harmonics Calculations section for details).
|
|
ADE7880_HYWATTOS, // 0x43AF R/W 24 32 ZPSE S 0x000000 Active power offset adjust on harmonic Y (see Harmonics Calculations section for details).
|
|
ADE7880_HZWATTOS, // 0x43B0 R/W 24 32 ZPSE S 0x000000 Active power offset adjust on harmonic Z (see Harmonics Calculations section for details).
|
|
ADE7880_HXVAROS, // 0x43B1 R/W 24 32 ZPSE S 0x000000 Active power offset adjust on harmonic X (see Harmonics Calculations section for details).
|
|
ADE7880_HYVAROS, // 0x43B2 R/W 24 32 ZPSE S 0x000000 Active power offset adjust on harmonic Y (see Harmonics Calculations section for details).
|
|
ADE7880_HZVAROS, // 0x43B3 R/W 24 32 ZPSE S 0x000000 Active power offset adjust on harmonic Z (see Harmonics Calculations section for details).
|
|
ADE7880_HXIRMSOS, // 0x43B4 R/W 24 32 ZPSE S 0x000000 Current rms offset on harmonic X (see Harmonics Calculations section for details).
|
|
ADE7880_HYIRMSOS, // 0x43B5 R/W 24 32 ZPSE S 0x000000 Current rms offset on harmonic Y (see Harmonics Calculations section for details).
|
|
ADE7880_HZIRMSOS, // 0x43B6 R/W 24 32 ZPSE S 0x000000 Current rms offset on harmonic Z (see Harmonics Calculations section for details).
|
|
ADE7880_HXVRMSOS, // 0x43B7 R/W 24 32 ZPSE S 0x000000 Voltage rms offset on harmonic X (see Harmonics Calculations section for details).
|
|
ADE7880_HYVRMSOS, // 0x43B8 R/W 24 32 ZPSE S 0x000000 Voltage rms offset on harmonic Y (see Harmonics Calculations section for details).
|
|
ADE7880_HZVRMSOS, // 0x43B9 R/W 24 32 ZPSE S 0x000000 Voltage rms offset on harmonic Z (see Harmonics Calculations section for details).
|
|
ADE7880_AIRMS = 0x43C0, // 0x43C0 R 24 32 ZP S N/A Phase A current rms value.
|
|
ADE7880_AVRMS, // 0x43C1 R 24 32 ZP S N/A Phase A voltage rms value.
|
|
ADE7880_BIRMS, // 0x43C2 R 24 32 ZP S N/A Phase B current rms value.
|
|
ADE7880_BVRMS, // 0x43C3 R 24 32 ZP S N/A Phase B voltage rms value.
|
|
ADE7880_CIRMS, // 0x43C4 R 24 32 ZP S N/A Phase C current rms value.
|
|
ADE7880_CVRMS, // 0x43C5 R 24 32 ZP S N/A Phase C voltage rms value.
|
|
ADE7880_NIRMS, // 0x43C6 R 24 32 ZP S N/A Neutral current rms value.
|
|
ADE7880_ISUM // 0x43C7 R 28 32 ZP S N/A Sum of IAWV, IBWV and ICWV registers.
|
|
};
|
|
|
|
enum Ade7880InternalDspRegisters {
|
|
ADE7880_Run = 0xE228 // 0xE228 R/W 16 16 U 0x0000 Run register starts and stops the DSP. See the Digital Signal Processor section for more details.
|
|
};
|
|
|
|
enum Ade7880BillableRegisters {
|
|
ADE7880_AWATTHR = 0xE400, // 0xE400 R 32 32 S 0x00000000 Phase A total active energy accumulation.
|
|
ADE7880_BWATTHR, // 0xE401 R 32 32 S 0x00000000 Phase B total active energy accumulation.
|
|
ADE7880_CWATTHR, // 0xE402 R 32 32 S 0x00000000 Phase C total active energy accumulation.
|
|
ADE7880_AFWATTHR, // 0xE403 R 32 32 S 0x00000000 Phase A fundamental active energy accumulation.
|
|
ADE7880_BFWATTHR, // 0xE404 R 32 32 S 0x00000000 Phase B fundamental active energy accumulation.
|
|
ADE7880_CFWATTHR, // 0xE405 R 32 32 S 0x00000000 Phase C fundamental active energy accumulation.
|
|
ADE7880_AFVARHR = 0xE409, // 0xE409 R 32 32 S 0x00000000 Phase A fundamental reactive energy accumulation.
|
|
ADE7880_BFVARHR, // 0xE40A R 32 32 S 0x00000000 Phase B fundamental reactive energy accumulation.
|
|
ADE7880_CFVARHR, // 0xE40B R 32 32 S 0x00000000 Phase C fundamental reactive energy accumulation.
|
|
ADE7880_AVAHR, // 0xE40C R 32 32 S 0x00000000 Phase A apparent energy accumulation.
|
|
ADE7880_BVAHR, // 0xE40D R 32 32 S 0x00000000 Phase B apparent energy accumulation.
|
|
ADE7880_CVAHR // 0xE40E R 32 32 S 0x00000000 Phase C apparent energy accumulation.
|
|
};
|
|
|
|
enum Ade7880PowerQualityRegisters {
|
|
ADE7880_IPEAK = 0xE500, // 0xE500 R 32 32 U N/A Current peak register. See Figure 60 and Table 34 for details about its composition.
|
|
ADE7880_VPEAK, // 0xE501 R 32 32 U N/A Voltage peak register. See Figure 60 and Table 35 for details about its composition.
|
|
ADE7880_STATUS0, // 0xE502 R/W 32 32 U N/A Interrupt Status Register 0. See Table 36.
|
|
ADE7880_STATUS1, // 0xE503 R/W 32 32 U N/A Interrupt Status Register 1. See Table 37.
|
|
ADE7880_AIMAV, // 0xE504 R 20 32 ZP U N/A Phase A current mean absolute value computed during PSM0 and PSM1 modes.
|
|
ADE7880_BIMAV, // 0xE505 R 20 32 ZP U N/A Phase B current mean absolute value computed during PSM0 and PSM1 modes.
|
|
ADE7880_CIMAV, // 0xE506 R 20 32 ZP U N/A Phase C current mean absolute value computed during PSM0 and PSM1 modes.
|
|
ADE7880_OILVL, // 0xE507 R/W 24 32 ZP U 0xFFFFFF Overcurrent threshold.
|
|
ADE7880_OVLVL, // 0xE508 R/W 24 32 ZP U 0xFFFFFF Overvoltage threshold.
|
|
ADE7880_SAGLVL, // 0xE509 R/W 24 32 ZP U 0x000000 Voltage SAG level threshold.
|
|
ADE7880_MASK0, // 0xE50A R/W 32 32 U 0x00000000 Interrupt Enable Register 0. See Table 38.
|
|
ADE7880_MASK1, // 0xE50B R/W 32 32 U 0x00000000 Interrupt Enable Register 1. See Table 39.
|
|
ADE7880_IAWV, // 0xE50C R 24 32 SE S N/A Instantaneous value of Phase A current.
|
|
ADE7880_IBWV, // 0xE50D R 24 32 SE S N/A Instantaneous value of Phase B current.
|
|
ADE7880_ICWV, // 0xE50E R 24 32 SE S N/A Instantaneous value of Phase C current.
|
|
ADE7880_INWV, // 0xE50F R 24 32 SE S N/A Instantaneous value of neutral current.
|
|
ADE7880_VAWV, // 0xE510 R 24 32 SE S N/A Instantaneous value of Phase A voltage.
|
|
ADE7880_VBWV, // 0xE511 R 24 32 SE S N/A Instantaneous value of Phase B voltage.
|
|
ADE7880_VCWV, // 0xE512 R 24 32 SE S N/A Instantaneous value of Phase C voltage.
|
|
ADE7880_AWATT, // 0xE513 R 24 32 SE S N/A Instantaneous value of Phase A total active power.
|
|
ADE7880_BWATT, // 0xE514 R 24 32 SE S N/A Instantaneous value of Phase B total active power.
|
|
ADE7880_CWATT, // 0xE515 R 24 32 SE S N/A Instantaneous value of Phase C total active power.
|
|
ADE7880_AVA = 0xE519, // 0xE519 R 24 32 SE S N/A Instantaneous value of Phase A apparent power.
|
|
ADE7880_BVA, // 0xE51A R 24 32 SE S N/A Instantaneous value of Phase B apparent power.
|
|
ADE7880_CVA, // 0xE51B R 24 32 SE S N/A Instantaneous value of Phase C apparent power.
|
|
ADE7880_CHECKSUM = 0xE51F, // 0xE51F R 32 32 U 0xAFFA63B9 Checksum verification. See the Checksum Register section for details.
|
|
ADE7880_VNOM, // 0xE520 R/W 24 32 ZP S 0x000000 Nominal phase voltage rms used in the alternative computation of the apparent power. When the VNOMxEN bit is set, the
|
|
// applied voltage input in the corresponding phase is ignored and all corresponding rms voltage instances are replaced by the value in the VNOM register.
|
|
ADE7880_LAST_RWDATA32 = 0xE5FF, // 0xE5FF R 32 32 U N/A Contains the data from the last successful 32-bit register communication.
|
|
ADE7880_PHSTATUS, // 0xE600 R 16 16 U N/A Phase peak register. See Table 40.
|
|
ADE7880_ANGLE0, // 0xE601 R 16 16 U N/A Time Delay 0. See the Time Interval Between Phases section for details.
|
|
ADE7880_ANGLE1, // 0xE602 R 16 16 U N/A Time Delay 1. See the Time Interval Between Phases section for details.
|
|
ADE7880_ANGLE2, // 0xE603 R 16 16 U N/A Time Delay 2. See the Time Interval Between Phases section for details.
|
|
ADE7880_PHNOLOAD = 0xE608, // 0xE608 R 16 16 U N/A Phase no load register. See Table 41.
|
|
ADE7880_LINECYC = 0xE60C, // 0xE60C R/W 16 16 U 0xFFFF Line cycle accumulation mode count.
|
|
ADE7880_ZXTOUT, // 0xE60D R/W 16 16 U 0xFFFF Zero-crossing timeout count.
|
|
ADE7880_COMPMODE, // 0xE60E R/W 16 16 U 0x01FF Computation-mode register. See Table 42.
|
|
ADE7880_Gain, // 0xE60F R/W 16 16 U 0x0000 PGA gains at ADC inputs. See Table 43.
|
|
ADE7880_CFMODE, // 0xE610 R/W 16 16 U 0x0EA0 CFx configuration register. See Table 44.
|
|
ADE7880_CF1DEN, // 0xE611 R/W 16 16 U 0x0000 CF1 denominator.
|
|
ADE7880_CF2DEN, // 0xE612 R/W 16 16 U 0x0000 CF2 denominator.
|
|
ADE7880_CF3DEN, // 0xE613 R/W 16 16 U 0x0000 CF3 denominator.
|
|
ADE7880_APHCAL, // 0xE614 R/W 10 16 ZP S 0x0000 Phase calibration of Phase A. See Table 45.
|
|
ADE7880_BPHCAL, // 0xE615 R/W 10 16 ZP S 0x0000 Phase calibration of Phase B. See Table 45.
|
|
ADE7880_CPHCAL, // 0xE616 R/W 10 16 ZP S 0x0000 Phase calibration Phase of C. See Table 45.
|
|
ADE7880_PHSIGN, // 0xE617 R 16 16 U N/A Power sign register. See Table 46.
|
|
ADE7880_CONFIG, // 0xE618 R/W 16 16 U 0x0002 ADE7880 configuration register. See Table 47.
|
|
ADE7880_MMODE = 0xE700, // 0xE700 R/W 8 8 U 0x1C Measurement mode register. See Table 48.
|
|
ADE7880_ACCMODE, // 0xE701 R/W 8 8 U 0x80 Accumulation mode register. See Table 49.
|
|
ADE7880_LCYCMODE, // 0xE702 R/W 8 8 U 0x78 Line accumulation mode behavior. See Table 51.
|
|
ADE7880_PEAKCYC, // 0xE703 R/W 8 8 U 0x00 Peak detection half line cycles.
|
|
ADE7880_SAGCYC, // 0xE704 R/W 8 8 U 0x00 SAG detection half line cycles.
|
|
ADE7880_CFCYC, // 0xE705 R/W 8 8 U 0x01 Number of CF pulses between two consecutive energy latches. See the Synchronizing Energy Registers with CFx Outputs section.
|
|
ADE7880_HSDC_CFG, // 0xE706 R/W 8 8 U 0x00 HSDC configuration register. See Table 52.
|
|
ADE7880_Version, // 0xE707 R 8 8 U Version of die.
|
|
ADE7880_DSPWP_SET = 0xE7E3, // 0xE7E3 W 8 8 U 0x00 Write protect DSP (0x80) or enable write (0x00). See page 40.
|
|
ADE7880_Reserved, // 0xE7E4 R 8 8 U 0x08 This register must remain at this value for checksum functionality to work. If this register shows a different value while being read, reset the chip before working with the checksum feature.
|
|
ADE7880_LAST_RWDATA8 = 0xE7FD, // 0xE7FD R 8 8 U N/A Contains the data from the last successful 8-bit register communication.
|
|
ADE7880_DSPWP_SEL, // 0xE7FE W 8 8 U 0xAD Select DSP writeprotect. See page 40.
|
|
ADE7880_FVRMS = 0xE880, // 0xE880 R 24 32 S N/A The rms value of the fundamental component of the phase voltage.
|
|
ADE7880_FIRMS, // 0xE881 R 24 32 S N/A The rms value of the fundamental component of the phase current
|
|
ADE7880_FWATT, // 0xE882 R 24 32 S N/A The active power of the fundamental component.
|
|
ADE7880_FVAR, // 0xE883 R 24 32 S N/A The reactive power of the fundamental component.
|
|
ADE7880_FVA, // 0xE884 R 24 32 S N/A The apparent power of the fundamental component.
|
|
ADE7880_FPF, // 0xE885 R 24 32 S N/A The power factor of the fundamental component.
|
|
ADE7880_VTHD, // 0xE886 R 24 32 S N/A Total harmonic distortion of the phase voltage.
|
|
ADE7880_ITHD, // 0xE887 R 24 32 S N/A Total harmonic distortion of the phase current.
|
|
ADE7880_HXVRMS, // 0xE888 R 24 32 S N/A The rms value of the phase voltage harmonic X.
|
|
ADE7880_HXIRMS, // 0xE889 R 24 32 S N/A The rms value of the phase current harmonic X.
|
|
ADE7880_HXWATT, // 0xE88A R 24 32 S N/A The active power of the harmonic X.
|
|
ADE7880_HXVAR, // 0xE88B R 24 32 S N/A The reactive power of the harmonic X.
|
|
ADE7880_HXVA, // 0xE88C R 24 32 S N/A The apparent power of the harmonic X.
|
|
ADE7880_HXPF, // 0xE88D R 24 32 S N/A The power factor of the harmonic X.
|
|
ADE7880_HXVHD, // 0xE88E R 24 32 S N/A Harmonic distortion of the phase voltage harmonic X relative to the fundamental.
|
|
ADE7880_HXIHD, // 0xE88F R 24 32 S N/A Harmonic distortion of the phase current harmonic X relative to the fundamental.
|
|
ADE7880_HYVRMS, // 0xE890 R 24 32 S N/A The rms value of the phase voltage harmonic Y.
|
|
ADE7880_HYIRMS, // 0xE891 R 24 32 S N/A The rms value of the phase current harmonic Y.
|
|
ADE7880_HYWATT, // 0xE892 R 24 32 S N/A The active power of the harmonic Y.
|
|
ADE7880_HYVAR, // 0xE893 R 24 32 S N/A The reactive power of the harmonic Y.
|
|
ADE7880_HYVA, // 0xE894 R 24 32 S N/A The apparent power of the harmonic Y.
|
|
ADE7880_HYPF, // 0xE895 R 24 32 S N/A The power factor of the harmonic Y.
|
|
ADE7880_HYVHD, // 0xE896 R 24 32 S N/A Harmonic distortion of the phase voltage harmonic Y relative to the fundamental.
|
|
ADE7880_HYIHD, // 0xE897 R 24 32 S N/A Harmonic distortion of the phase current harmonic Y relative to the fundamental.
|
|
ADE7880_HZVRMS, // 0xE898 R 24 32 S N/A The rms value of the phase voltage harmonic Z.
|
|
ADE7880_HZIRMS, // 0xE899 R 24 32 S N/A The rms value of the phase current harmonic Z.
|
|
ADE7880_HZWATT, // 0xE89A R 24 32 S N/A The active power of the harmonic Z.
|
|
ADE7880_HZVAR, // 0xE89B R 24 32 S N/A The reactive power of the harmonic Z.
|
|
ADE7880_HZVA, // 0xE89C R 24 32 S N/A The apparent power of the harmonic Z.
|
|
ADE7880_HZPF, // 0xE89D R 24 32 S N/A The power factor of the harmonic Z.
|
|
ADE7880_HZVHD, // 0xE89E R 24 32 S N/A Harmonic distortion of the phase voltage harmonic Z relative to the fundamental.
|
|
ADE7880_HZIHD, // 0xE89F R 24 32 S N/A Harmonic distortion of the phase current harmonic Z relative to the fundamental.
|
|
ADE7880_HCONFIG = 0xE900, // 0xE900 R/W 16 16 U 0x08 Harmonic Calculations Configuration register. See Table 54.
|
|
ADE7880_APF = 0xE902, // 0xE902 R 16 16 S N/A Phase A power factor.
|
|
ADE7880_BPF, // 0xE903 R 16 16 S N/A Phase B power factor.
|
|
ADE7880_CPF, // 0xE904 R 16 16 S N/A Phase C power factor.
|
|
ADE7880_APERIOD, // 0xE905 R 16 16 U N/A Line period on Phase A voltage.
|
|
ADE7880_BPERIOD, // 0xE906 R 16 16 U N/A Line period on Phase B voltage.
|
|
ADE7880_CPERIOD, // 0xE907 R 16 16 U N/A Line period on Phase C voltage.
|
|
ADE7880_APNOLOAD, // 0xE908 R/W 16 16 U 0x0000 No load threshold in the total/ fundamental active power data paths. Do not write 0xFFFF to this register.
|
|
ADE7880_VARNOLOAD, // 0xE909 R/W 16 16 U 0x0000 No load threshold in the total/ fundamental reactive power data path. Do not write 0xFFFF to this register.
|
|
ADE7880_VANOLOAD, // 0xE90A R/W 16 16 U 0x0000 No load threshold in the apparent power data path. Do not write 0xFFFF to this register.
|
|
ADE7880_LAST_ADD = 0xE9FE, // 0xE9FE R 16 16 U N/A The address of the register successfully accessed during the last read/write operation.
|
|
ADE7880_LAST_RWDATA16, // 0xE9FF R 16 16 U N/A Contains the data from the last successful 16-bit register communication.
|
|
ADE7880_CONFIG3, // 0xEA00 R/W 8 8 U 0x01 Configuration register. See Table 53.
|
|
ADE7880_LAST_OP, // 0xEA01 R 8 8 U N/A Indicates the type, read or write, of the last successful read/write operation.
|
|
ADE7880_WTHR, // 0xEA02 R/W 8 8 U 0x03 Threshold used in phase total/fundamental active power data path.
|
|
ADE7880_VARTHR, // 0xEA03 R/W 8 8 U 0x03 Threshold used in phase total/fundamental reactive power data path.
|
|
ADE7880_VATHR, // 0xEA04 R/W 8 8 U 0x03 Threshold used in phase apparent power data path.
|
|
ADE7880_HX = 0xEA08, // 0xEA08 R/W 8 8 U 3 Selects an index of the harmonic monitored by the harmonic computations.
|
|
ADE7880_HY, // 0xEA09 R/W 8 8 U 5 Selects an index of the harmonic monitored by the harmonic computations.
|
|
ADE7880_HZ, // 0xEA0A R/W 8 8 U 7 Selects an index of the harmonic monitored by the harmonic computations.
|
|
ADE7880_LPOILVL = 0xEC00, // 0xEC00 R/W 8 8 U 0x07 Overcurrent threshold used during PSM2 mode. See Table 55 in which the register is detailed.
|
|
ADE7880_CONFIG2 // 0xEC01 R/W 8 8 U 0x00 Configuration register used during PSM1 mode. See Table 56.
|
|
};
|
|
|
|
struct Ade7880 {
|
|
float neutral_current;
|
|
int32_t calib_current[4];
|
|
int32_t calib_voltage[3];
|
|
int32_t calib_acpower[3];
|
|
uint16_t calib_angle[3];
|
|
bool calib_frequency;
|
|
bool irq0_state;
|
|
uint8_t cycle_count;
|
|
uint8_t watchdog;
|
|
} Ade7880;
|
|
|
|
/*********************************************************************************************/
|
|
|
|
int Ade7880RegSize(uint16_t reg) {
|
|
int size = 0;
|
|
switch ((reg >> 8) & 0x0F) {
|
|
case 0x03: // 32-bit
|
|
case 0x04:
|
|
case 0x05:
|
|
case 0x08:
|
|
size++;
|
|
size++;
|
|
case 0x01: // 16-bit
|
|
case 0x02:
|
|
case 0x06:
|
|
case 0x09:
|
|
size++;
|
|
case 0x00: // 8-bit
|
|
case 0x07:
|
|
case 0x0A:
|
|
case 0x0B:
|
|
case 0x0C:
|
|
size++;
|
|
}
|
|
return size;
|
|
}
|
|
|
|
void Ade7880Write(uint16_t reg, uint32_t val) {
|
|
int size = Ade7880RegSize(reg);
|
|
if (size) {
|
|
#ifdef ADE7880_DEBUG
|
|
char log_format[100];
|
|
snprintf_P(log_format, sizeof(log_format), PSTR("A78: Wr 0x%%04X 0x%%0%dX (%%d)"), size << 1);
|
|
AddLog(LOG_LEVEL_DEBUG_MORE, log_format, reg, val, val);
|
|
#endif // ADE7880_DEBUG
|
|
Wire.beginTransmission(ADE7880_ADDR);
|
|
Wire.write((reg >> 8) & 0xFF);
|
|
Wire.write(reg & 0xFF);
|
|
while (size--) {
|
|
Wire.write((val >> (8 * size)) & 0xFF); // Write data, MSB first
|
|
}
|
|
Wire.endTransmission();
|
|
delayMicroseconds(5); // Bus-free time minimum 4.7us
|
|
}
|
|
}
|
|
|
|
bool Ade7880VerifyWrite(uint16_t reg) {
|
|
uint32_t error = 0;
|
|
error += (0xCA != Ade7880Read(ADE7880_LAST_OP)); // Indicates the type, read (0x35) or write (0xCA), of the last successful read/write operation.
|
|
error += (reg != Ade7880Read(ADE7880_LAST_ADD)); // The address of the register successfully accessed during the last read/write operation.
|
|
if (error) {
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Write verify error"));
|
|
return false;
|
|
}
|
|
return true;
|
|
}
|
|
|
|
bool Ade7880WriteVerify(uint16_t reg, uint32_t val) {
|
|
Ade7880Write(reg, val);
|
|
return Ade7880VerifyWrite(reg);
|
|
}
|
|
|
|
int32_t Ade7880Read(uint16_t reg) {
|
|
uint32_t response = 0;
|
|
int size = Ade7880RegSize(reg);
|
|
if (size) {
|
|
Wire.beginTransmission(ADE7880_ADDR);
|
|
Wire.write((reg >> 8) & 0xFF);
|
|
Wire.write(reg & 0xFF);
|
|
Wire.endTransmission(0);
|
|
Wire.requestFrom(ADE7880_ADDR, size);
|
|
if (size <= Wire.available()) {
|
|
for (uint32_t i = 0; i < size; i++) {
|
|
response = response << 8 | Wire.read(); // receive DATA (MSB first)
|
|
}
|
|
}
|
|
#ifdef ADE7880_DEBUG
|
|
if ((reg != ADE7880_LAST_OP) && (reg != ADE7880_LAST_ADD)) {
|
|
char log_format[100];
|
|
snprintf_P(log_format, sizeof(log_format), PSTR("A78: Rd 0x%%04X 0x%%0%dX (%%d)"), size << 1);
|
|
AddLog(LOG_LEVEL_DEBUG_MORE, log_format, reg, response, response);
|
|
}
|
|
#endif // ADE7880_DEBUG
|
|
}
|
|
return response;
|
|
}
|
|
|
|
int32_t Ade7880ReadVerify(uint16_t reg) {
|
|
int32_t result = Ade7880Read(reg);
|
|
uint32_t error = 0;
|
|
error += (0x35 != Ade7880Read(ADE7880_LAST_OP)); // Indicates the type, read (0x35) or write (0xCA), of the last successful read/write operation.
|
|
error += (reg != Ade7880Read(ADE7880_LAST_ADD)); // The address of the register successfully accessed during the last read/write operation.
|
|
if (error) {
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Read verify error"));
|
|
}
|
|
return result;
|
|
}
|
|
|
|
/*********************************************************************************************/
|
|
|
|
bool Ade7880Init(void) {
|
|
// Init sequence about 6mS after reset - See page 40 (takes 68ms)
|
|
#ifdef ADE7880_PROFILING
|
|
uint32_t start = millis();
|
|
#endif // ADE7880_PROFILING
|
|
|
|
uint32_t status1 = Ade7880ReadVerify(ADE7880_STATUS1); // 0xE503 - 0x01A08000
|
|
if (bitRead(status1, 15)) { // RSTDONE
|
|
// Power on or Reset
|
|
Ade7880WriteVerify(ADE7880_CONFIG2, 0x02); // 0xEC01 - ADE7880_I2C_LOCK
|
|
Ade7880WriteVerify(ADE7880_STATUS1, 0x3FFE8930); // 0xE503 - Acknowledge RSTDONE - Reset IRQ1 line
|
|
status1 = Ade7880ReadVerify(ADE7880_STATUS1); // 0xE503 - 0x01A00007
|
|
} else {
|
|
return false;
|
|
}
|
|
uint8_t version = Ade7880ReadVerify(ADE7880_Version); // 0xE707 - 0x01
|
|
Ade7880WriteVerify(ADE7880_Gain, 0x0000); // 0xE60F - Gain register set to 1 for current, and voltage
|
|
if (Ade7880.calib_frequency) {
|
|
Ade7880WriteVerify(ADE7880_COMPMODE, 0x41FF); // 0xE60E - Connected to networks with fundamental frequencies between 55 Hz and 66 Hz. Default is 45 Hz and 55 Hz.
|
|
}
|
|
|
|
for (uint32_t phase = 0; phase < 3; phase++) {
|
|
Ade7880WriteVerify(ADE7880_AVGAIN + (phase * 2), Ade7880.calib_voltage[phase]); // 0x4381
|
|
Ade7880WriteVerify(ADE7880_AIGAIN + (phase * 2), Ade7880.calib_current[phase]); // 0x4380
|
|
Ade7880WriteVerify(ADE7880_APGAIN + (phase * 2), Ade7880.calib_acpower[phase]); // 0x4389
|
|
Ade7880WriteVerify(ADE7880_APHCAL + phase, Ade7880.calib_angle[phase]); // 0xE614
|
|
}
|
|
Ade7880WriteVerify(ADE7880_NIGAIN, Ade7880.calib_current[3]); // 0x4386
|
|
Ade7880WriteVerify(ADE7880_NIGAIN, Ade7880.calib_current[3]); // 0x4386 - Write last data memory RAM three times (page 40)
|
|
Ade7880WriteVerify(ADE7880_NIGAIN, Ade7880.calib_current[3]); // 0x4386
|
|
|
|
bool error = false;
|
|
for (uint32_t phase = 0; phase < 3; phase++) {
|
|
if (Ade7880ReadVerify(ADE7880_AVGAIN + (phase * 2)) != (Ade7880.calib_voltage[phase] & 0x0FFFFFFF)) { error = true; }
|
|
else if (Ade7880ReadVerify(ADE7880_AIGAIN + (phase * 2)) != (Ade7880.calib_current[phase] & 0x0FFFFFFF)) { error = true; }
|
|
else if (Ade7880ReadVerify(ADE7880_APGAIN + (phase * 2)) != (Ade7880.calib_acpower[phase] & 0x0FFFFFFF)) { error = true; }
|
|
else if (Ade7880ReadVerify(ADE7880_APHCAL + phase) != (Ade7880.calib_angle[phase] & 0x00FF)) { error = true; }
|
|
}
|
|
if (Ade7880ReadVerify(ADE7880_NIGAIN) != (Ade7880.calib_current[3] & 0x0FFFFFFF)) { error = true; }
|
|
if (error) {
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Error initializing parameters"));
|
|
return false;
|
|
}
|
|
|
|
if (!Ade7880WriteVerify(ADE7880_LCYCMODE, 0x09)) { // 0xE702 - Line cycle accumulation mode
|
|
// - Watt-hour accumulation registers (AWATTHR, BWATTHR, CWATTHR, AFWATTHR, BFWATTHR, and CFWATTHR) are placed into line cycle accumulation mode.
|
|
// - Phase A is selected for zero-crossings counts in the line cycle accumulation mode.
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Error setting LCYCMODE register"));
|
|
return false;
|
|
}
|
|
uint32_t line_cycle = (Ade7880.calib_frequency) ? 120 : 100; // Either 60Hz or 50Hz to have 1 second interrupts
|
|
if (!Ade7880WriteVerify(ADE7880_LINECYC, line_cycle)) { // 0xE60C - = 100
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Error setting LINECYC register"));
|
|
return false;
|
|
}
|
|
Ade7880WriteVerify(ADE7880_MASK0, 0x00000020); // 0xE50A - IRQ0 at end of an integration over an integer number of half line cycles set in the LINECYC register.
|
|
if (!Ade7880VerifyWrite(ADE7880_MASK0)) { // 0xE50A
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Error setting MASK0 register"));
|
|
return false;
|
|
}
|
|
Ade7880Write(ADE7880_MASK0, 0x00000020); // 0xE50A
|
|
Ade7880Write(ADE7880_DSPWP_SEL, 0xAD); // 0xE7FE - Select DSP write protection
|
|
Ade7880Write(ADE7880_DSPWP_SET, 0x80); // 0xE7E3 - Write protect DSP area
|
|
Ade7880WriteVerify(ADE7880_Run, 0x0201); // 0xE228 - Start DSP
|
|
|
|
#ifdef ADE7880_PROFILING
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Init done in %d ms"), millis() - start);
|
|
#endif // ADE7880_PROFILING
|
|
|
|
return true;
|
|
}
|
|
|
|
bool Ade7880SetCalibrate(void) {
|
|
|
|
#ifdef ADE7880_PROFILING
|
|
uint32_t start = millis();
|
|
#endif // ADE7880_PROFILING
|
|
|
|
int reset = Pin(GPIO_RESET);
|
|
if (-1 == reset) { reset = 16; } // Reset pin ADE7880 in Shelly 3EM
|
|
pinMode(reset, OUTPUT);
|
|
digitalWrite(reset, 0);
|
|
delay(1);
|
|
digitalWrite(reset, 1);
|
|
pinMode(reset, INPUT);
|
|
|
|
Ade7880.cycle_count = 2; // Skip first two cycles
|
|
|
|
uint32_t timeout = millis() + 100; // Should be reset within 10 ms
|
|
while (!TimeReached(timeout)) { // Wait up to 100 ms
|
|
if (!digitalRead(Pin(GPIO_ADE7880_IRQ, 1))) {
|
|
|
|
#ifdef ADE7880_PROFILING
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Reset in %d ms"), millis() - start);
|
|
#endif // ADE7880_PROFILING
|
|
|
|
if (Ade7880Init()) {
|
|
Ade7880.watchdog = 0;
|
|
return true;
|
|
}
|
|
}
|
|
}
|
|
return false;
|
|
}
|
|
|
|
/*********************************************************************************************/
|
|
|
|
void Ade7880Cycle(void) {
|
|
// Cycle sequence (takes 55ms)
|
|
#ifdef ADE7880_PROFILING
|
|
uint32_t start = millis();
|
|
#endif // ADE7880_PROFILING
|
|
|
|
uint32_t status0 = Ade7880ReadVerify(ADE7880_STATUS0); // 0xE502 - 0x000FEFE0
|
|
/*
|
|
if (!bitRead(status0, 5)) { // LENERGY
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Unexpected ISR0 0x%08X"), status0);
|
|
return;
|
|
} else {
|
|
Ade7880WriteVerify(ADE7880_STATUS0, 0x00000020); // 0xE502 - Acknowledge LENERGY - Reset IRQ0 line
|
|
status0 = Ade7880ReadVerify(ADE7880_STATUS0); // 0xE502 - 0x000FEFC0
|
|
}
|
|
*/
|
|
if (!bitRead(status0, 5)) { // LENERGY
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Unexpected ISR0 0x%08X"), status0);
|
|
}
|
|
Ade7880WriteVerify(ADE7880_STATUS0, 0x00000020); // 0xE502 - Acknowledge LENERGY - Reset IRQ0 line
|
|
status0 = Ade7880ReadVerify(ADE7880_STATUS0); // 0xE502 - 0x000FEFC0
|
|
|
|
if (Ade7880.cycle_count) { // Allow calibration stabilization
|
|
Ade7880.cycle_count--;
|
|
return; // Skip first cycles
|
|
}
|
|
Ade7880.neutral_current = (float)Ade7880ReadVerify(ADE7880_NIRMS) / 100000; // 0x43C6
|
|
for (uint32_t phase = 0; phase < 3; phase++) {
|
|
Energy.data_valid[phase] = 0;
|
|
Energy.voltage[phase] = (float)Ade7880ReadVerify(ADE7880_AVRMS + (phase * 2)) / 10000; // 0x43C1 - 0x0024CC94 = 241.1668 V
|
|
Energy.current[phase] = (float)Ade7880ReadVerify(ADE7880_AIRMS + (phase * 2)) / 100000; // 0x43C0 - 0x00002D6D = 0.11629 A
|
|
Energy.active_power[phase] = (float)Ade7880ReadVerify(ADE7880_AWATT + phase) / 100; // 0xE513 - 0xFFFFF524 = -27.79 W
|
|
Energy.apparent_power[phase] = (float)Ade7880ReadVerify(ADE7880_AVA + phase) / 100; // 0xE519 - 0xFFFFF50D
|
|
Energy.frequency[phase] = 256000.0f / Ade7880ReadVerify(ADE7880_APERIOD + phase); // 0xE905 - Page 34 and based on ADE7880_FREQ_INIT
|
|
// Suppose constant load during period of 100/120 periods as set by ADE7880_LINECYC disregards load change inbetween.
|
|
// ADE7880_AWATT = 6713 = 67,13 W
|
|
// 67,13 * 1000 / 36 = 1864 deca micro Wh (0.01864Wh)
|
|
// Energy.kWhtoday_delta[phase] += Energy.active_power[phase] * 1000 / 36;
|
|
|
|
// By measuring load 1024000 times/second load change in 100/120 periods can be accounted for.
|
|
// ADE7880_AWATT = 6713 = 67,13 W
|
|
// ADE7880_AWATTHR = 273
|
|
// AWATT multiplier is 16 (Figure 77)
|
|
// ADE7880_WTHR = 3 (default)
|
|
// Active power accumulation rate is 1.024MHz (Page 49)
|
|
// 1024000 * 16 * ADE7880_AWATT / ADE7880_WTHR * 0x8000000 = ADE7880_AWATTHR
|
|
// 1024000 * 16 * 6713 / 3 * 134217728 = 273
|
|
// 16384000 * 6713 / 402653184 = 273
|
|
// 273 * 402653184 / 16384000 = 6709 = 67,09W * 1000 / 36 = 1863 deca micro Wh (Tasmota needs deca micro Wh)
|
|
// 273 * 402653184 / 16384 = 6709248 = 67092,48W / 3600 = 1863 deca micro Wh
|
|
// 273 * 24576 = 6709248 / 3600 = 1863 deca micro Wh
|
|
int32_t active_energy = Ade7880ReadVerify(ADE7880_AWATTHR + phase); // 0xE400 - 0xFFFFFF8F = -0.112
|
|
Energy.kWhtoday_delta[phase] += active_energy * 24576 / 3600; // Using int32_t allows loads up to 87kW (0x7FFFFFFF / 24576)
|
|
}
|
|
EnergyUpdateToday();
|
|
|
|
#ifdef ADE7880_PROFILING
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Cycle in %d ms"), millis() - start);
|
|
#endif // ADE7880_PROFILING
|
|
}
|
|
|
|
void Ade7880Service0(void) {
|
|
// Poll sequence
|
|
SkipSleep(false);
|
|
Ade7880Cycle();
|
|
Ade7880.watchdog = 0;
|
|
Ade7880.irq0_state = 0;
|
|
}
|
|
|
|
void IRAM_ATTR Ade7880Isr0(void) {
|
|
// Poll sequence
|
|
if (!Ade7880.irq0_state) {
|
|
Ade7880.irq0_state = 1;
|
|
SkipSleep(true);
|
|
}
|
|
}
|
|
|
|
void Ade7880Watchdog(void) {
|
|
// Reinit if interrupt stopped
|
|
Ade7880.watchdog++;
|
|
if (Ade7880.watchdog > ADE7880_WATCHDOG) {
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Reinit"));
|
|
Ade7880SetCalibrate();
|
|
}
|
|
}
|
|
|
|
/*********************************************************************************************/
|
|
|
|
bool Ade7880SetDefaults(const char* json) {
|
|
// {"rms":{"current_a":3166385,"current_b":3125691,"current_c":3131983,"current_s":1756557,"voltage_a":-767262,"voltage_b":-763439,"voltage_c":-749854},"angles":{"angle0":180,"angle1":176,"angle2":176},"powers":{"totactive": {"a":-1345820,"b":-1347328,"c":-1351979}},"freq":0}
|
|
uint32_t len = strlen(json) +1;
|
|
if (len < 7) { return false; } // Too short
|
|
|
|
char json_buffer[len];
|
|
memcpy(json_buffer, json, len); // Keep original safe
|
|
JsonParser parser(json_buffer);
|
|
JsonParserObject root = parser.getRootObject();
|
|
if (!root) {
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Invalid JSON"));
|
|
return false;
|
|
}
|
|
|
|
// All parameters are optional allowing for partial changes
|
|
JsonParserToken val = root[PSTR("freq")];
|
|
if (val) { Ade7880.calib_frequency = val.getUInt(); }
|
|
JsonParserObject rms = root[PSTR("rms")].getObject();
|
|
if (rms) {
|
|
val = rms[PSTR("current_a")];
|
|
if (val) { Ade7880.calib_current[0] = val.getInt(); }
|
|
val = rms[PSTR("current_b")];
|
|
if (val) { Ade7880.calib_current[1] = val.getInt(); }
|
|
val = rms[PSTR("current_c")];
|
|
if (val) { Ade7880.calib_current[2] = val.getInt(); }
|
|
val = rms[PSTR("current_s")];
|
|
if (val) { Ade7880.calib_current[3] = val.getInt(); }
|
|
val = rms[PSTR("voltage_a")];
|
|
if (val) { Ade7880.calib_voltage[0] = val.getInt(); }
|
|
val = rms[PSTR("voltage_b")];
|
|
if (val) { Ade7880.calib_voltage[1] = val.getInt(); }
|
|
val = rms[PSTR("voltage_c")];
|
|
if (val) { Ade7880.calib_voltage[2] = val.getInt(); }
|
|
}
|
|
JsonParserObject angles = root[PSTR("angles")].getObject();
|
|
if (angles) {
|
|
val = angles[PSTR("angle0")];
|
|
if (val) { Ade7880.calib_angle[0] = val.getUInt(); }
|
|
val = angles[PSTR("angle1")];
|
|
if (val) { Ade7880.calib_angle[1] = val.getUInt(); }
|
|
val = angles[PSTR("angle2")];
|
|
if (val) { Ade7880.calib_angle[2] = val.getUInt(); }
|
|
}
|
|
JsonParserObject powers = root[PSTR("powers")].getObject();
|
|
if (powers) {
|
|
JsonParserObject totactive = powers[PSTR("totactive")].getObject();
|
|
if (totactive) {
|
|
val = totactive[PSTR("a")];
|
|
if (val) { Ade7880.calib_acpower[0] = val.getInt(); }
|
|
val = totactive[PSTR("b")];
|
|
if (val) { Ade7880.calib_acpower[1] = val.getInt(); }
|
|
val = totactive[PSTR("c")];
|
|
if (val) { Ade7880.calib_acpower[2] = val.getInt(); }
|
|
}
|
|
}
|
|
return true;
|
|
}
|
|
|
|
void Ade7880Defaults(void) {
|
|
Ade7880.calib_frequency = ADE7880_FREQ_INIT;
|
|
Ade7880.calib_current[0] = ADE7880_AIGAIN_INIT;
|
|
Ade7880.calib_current[1] = ADE7880_BIGAIN_INIT;
|
|
Ade7880.calib_current[2] = ADE7880_CIGAIN_INIT;
|
|
Ade7880.calib_current[3] = ADE7880_NIGAIN_INIT;
|
|
Ade7880.calib_voltage[0] = ADE7880_AVGAIN_INIT;
|
|
Ade7880.calib_voltage[1] = ADE7880_BVGAIN_INIT;
|
|
Ade7880.calib_voltage[2] = ADE7880_CVGAIN_INIT;
|
|
Ade7880.calib_acpower[0] = ADE7880_APGAIN_INIT;
|
|
Ade7880.calib_acpower[1] = ADE7880_BPGAIN_INIT;
|
|
Ade7880.calib_acpower[2] = ADE7880_CPGAIN_INIT;
|
|
Ade7880.calib_angle[0] = ADE7880_APHCAL_INIT;
|
|
Ade7880.calib_angle[1] = ADE7880_BPHCAL_INIT;
|
|
Ade7880.calib_angle[2] = ADE7880_CPHCAL_INIT;
|
|
|
|
#ifdef USE_RULES
|
|
// rule3 on file#calib.dat do {"rms":{"current_a":3166385,"current_b":3125691,"current_c":3131983,"current_s":1756557,"voltage_a":-767262,"voltage_b":-763439,"voltage_c":-749854},"angles":{"angle0":180,"angle1":176,"angle2":176},"powers":{"totactive": {"a":-1345820,"b":-1347328,"c":-1351979}},"freq":0} endon
|
|
String calib = RuleLoadFile("CALIB.DAT");
|
|
if (calib.length()) {
|
|
// AddLog(LOG_LEVEL_DEBUG, PSTR("A78: File '%s'"), calib.c_str());
|
|
Ade7880SetDefaults(calib.c_str());
|
|
}
|
|
#endif // USE_RULES
|
|
}
|
|
|
|
void Ade7880DrvInit(void) {
|
|
if (PinUsed(GPIO_ADE7880_IRQ) && PinUsed(GPIO_ADE7880_IRQ, 1)) {
|
|
if (I2cSetDevice(ADE7880_ADDR)) {
|
|
I2cSetActiveFound(ADE7880_ADDR, "ADE7880");
|
|
|
|
pinMode(Pin(GPIO_ADE7880_IRQ), INPUT);
|
|
attachInterrupt(Pin(GPIO_ADE7880_IRQ), Ade7880Isr0, FALLING);
|
|
Ade7880.irq0_state = 0;
|
|
pinMode(Pin(GPIO_ADE7880_IRQ, 1), INPUT);
|
|
|
|
Ade7880Defaults();
|
|
|
|
if (Ade7880SetCalibrate()) {
|
|
Energy.phase_count = 3; // Three phases
|
|
// Settings->flag5.energy_phase = 1; // SetOption129 - (Energy) Show phase information
|
|
// Energy.use_overtemp = true; // Use global temperature for overtemp detection
|
|
Energy.local_energy_active_export = true;
|
|
TasmotaGlobal.energy_driver = XNRG_23;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
bool Ade7880Command(void) {
|
|
bool serviced = false;
|
|
|
|
if (CMND_ENERGYCONFIG == Energy.command_code) {
|
|
// Non-pesistent settings
|
|
// EnergyConfig {"rms":{"current_a":3166385,"current_b":3125691,"current_c":3131983,"current_s":1756557,"voltage_a":-767262,"voltage_b":-763439,"voltage_c":-749854},"angles":{"angle0":180,"angle1":176,"angle2":176},"powers":{"totactive": {"a":-1345820,"b":-1347328,"c":-1351979}},"freq":0}
|
|
// EnergyConfig {"rms":{"voltage_c":-549854}}
|
|
// EnergyConfig {"freq":0}
|
|
if (XdrvMailbox.data_len) {
|
|
#ifdef ADE7880_DEBUG
|
|
if ('1' == XdrvMailbox.data[0]) {
|
|
// EnergyConfig 1 - Dump DSP data memory (0x4380..0x43B9)
|
|
char data[600] = { 0 };
|
|
for (uint32_t i = 0; i < 57; i++) {
|
|
int32_t value = Ade7880Read(ADE7880_AIGAIN + i);
|
|
// snprintf_P(data, sizeof(data), PSTR("%s%s%08X"), data, (i)?",":"", value);
|
|
if (bitRead(value, 27)) { value |= 0xF0000000; } // Make 24-bit negative (ZPSE)
|
|
snprintf_P(data, sizeof(data), PSTR("%s%s%d"), data, (i)?",":"", value);
|
|
}
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: DSP Regs 0x4380..B9 '%s'"), data);
|
|
return true;
|
|
}
|
|
if ('2' == XdrvMailbox.data[0]) {
|
|
// EnergyConfig 2 - Dump DSP UI data memory (0x43C0..0x43C7)
|
|
char data[600] = { 0 };
|
|
for (uint32_t i = 0; i < 8; i++) {
|
|
int32_t value = Ade7880Read(ADE7880_AIRMS + i);
|
|
snprintf_P(data, sizeof(data), PSTR("%s%s%08X"), data, (i)?",":"", value);
|
|
// if (7 == i) {
|
|
// if (bitRead(value, 27)) { value |= 0xF0000000; } // Make 28-bit negative (ZP)
|
|
// } else {
|
|
// if (bitRead(value, 23)) { value |= 0xFF000000; } // Make 24-bit negative (ZP)
|
|
// }
|
|
// snprintf_P(data, sizeof(data), PSTR("%s%s%d"), data, (i)?",":"", value);
|
|
}
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: DSP Regs 0x43C0..C7 '%s'"), data);
|
|
return true;
|
|
}
|
|
#endif // ADE7880_DEBUG
|
|
Ade7880Defaults(); // Load defaults
|
|
if (Ade7880SetDefaults(XdrvMailbox.data)) {
|
|
bool status = Ade7880SetCalibrate();
|
|
AddLog(LOG_LEVEL_DEBUG, PSTR("A78: Re-init status %d"), status);
|
|
}
|
|
}
|
|
Response_P(PSTR("{\"%s\":{"
|
|
"\"rms\":{\"current_a\":%d,\"current_b\":%d,\"current_c\":%d,\"current_s\":%d,\"voltage_a\":%d,\"voltage_b\":%d,\"voltage_c\":%d},"
|
|
"\"angles\":{\"angle0\":%d,\"angle1\":%d,\"angle2\":%d},"
|
|
"\"powers\":{\"totactive\":{\"a\":%d,\"b\":%d,\"c\":%d}},\"freq\":%d}}"),
|
|
XdrvMailbox.command,
|
|
Ade7880.calib_current[0], Ade7880.calib_current[1], Ade7880.calib_current[2], Ade7880.calib_current[3],
|
|
Ade7880.calib_voltage[0], Ade7880.calib_voltage[1], Ade7880.calib_voltage[2],
|
|
Ade7880.calib_angle[0], Ade7880.calib_angle[1], Ade7880.calib_angle[2],
|
|
Ade7880.calib_acpower[0], Ade7880.calib_acpower[1], Ade7880.calib_acpower[2], Ade7880.calib_frequency);
|
|
serviced = true;
|
|
}
|
|
|
|
return serviced;
|
|
}
|
|
|
|
/*********************************************************************************************\
|
|
* Show
|
|
\*********************************************************************************************/
|
|
|
|
#ifdef ADE7880_MORE_REGS
|
|
#ifdef USE_WEBSERVER
|
|
const char HTTP_ADE7880_CURRENT[] PROGMEM = "{s}" D_CURRENT_NEUTRAL "{m}%s " D_UNIT_AMPERE "{e}";
|
|
#endif // USE_WEBSERVER
|
|
|
|
void Ade7880Show(bool json) {
|
|
char value_chr[GUISZ];
|
|
|
|
if (json) {
|
|
ResponseAppend_P(PSTR(",\"" D_JSON_CURRENT_NEUTRAL "\":%s"),
|
|
EnergyFormat(value_chr, &Ade7880.neutral_current, Settings->flag2.current_resolution, 1));
|
|
#ifdef USE_WEBSERVER
|
|
} else {
|
|
WSContentSend_PD(HTTP_ADE7880_CURRENT, WebEnergyFormat(value_chr, &Ade7880.neutral_current, Settings->flag2.current_resolution, 1));
|
|
#endif // USE_WEBSERVER
|
|
}
|
|
}
|
|
#endif // ADE7880_MORE_REGS
|
|
|
|
/*********************************************************************************************\
|
|
* Interface
|
|
\*********************************************************************************************/
|
|
|
|
bool Xnrg23(uint8_t function) {
|
|
if (!I2cEnabled(XI2C_65)) { return false; }
|
|
|
|
bool result = false;
|
|
|
|
switch (function) {
|
|
case FUNC_LOOP:
|
|
if (Ade7880.irq0_state) { Ade7880Service0(); }
|
|
break;
|
|
case FUNC_EVERY_SECOND:
|
|
Ade7880Watchdog();
|
|
break;
|
|
#ifdef ADE7880_MORE_REGS
|
|
case FUNC_JSON_APPEND:
|
|
Ade7880Show(1);
|
|
break;
|
|
#ifdef USE_WEBSERVER
|
|
#ifdef USE_ENERGY_COLUMN_GUI
|
|
case FUNC_WEB_COL_SENSOR:
|
|
#else // not USE_ENERGY_COLUMN_GUI
|
|
case FUNC_WEB_SENSOR:
|
|
#endif // USE_ENERGY_COLUMN_GUI
|
|
Ade7880Show(0);
|
|
break;
|
|
#endif // USE_WEBSERVER
|
|
#endif // ADE7880_MORE_REGS
|
|
case FUNC_COMMAND:
|
|
result = Ade7880Command();
|
|
break;
|
|
case FUNC_PRE_INIT:
|
|
Ade7880DrvInit();
|
|
break;
|
|
}
|
|
return result;
|
|
}
|
|
|
|
#endif // USE_ADE7880
|
|
#endif // USE_ENERGY_SENSOR
|
|
#endif // USE_I2C
|