mirror of https://github.com/arendst/Tasmota.git
71 lines
2.5 KiB
C++
71 lines
2.5 KiB
C++
/*
|
|
* IRremoteESP8266: IRsendGCDemo
|
|
* demonstrates sending Global Cache-formatted IR codes with IRsend
|
|
* Copyright 2009 Ken Shirriff
|
|
* http://arcfn.com
|
|
*
|
|
* Version 0.2 June, 2017
|
|
* Added helpful comments
|
|
* Better includes files.
|
|
* Version 0.1 30 March, 2016
|
|
* Based on Ken Shirriff's IrsendDemo
|
|
* Version 0.1 July, 2009
|
|
*
|
|
* An IR LED circuit *MUST* be connected to the ESP8266 on a pin
|
|
* as specified by IR_LED below.
|
|
*
|
|
* TL;DR: The IR LED needs to be driven by a transistor for a good result.
|
|
*
|
|
* Suggested circuit:
|
|
* https://github.com/crankyoldgit/IRremoteESP8266/wiki#ir-sending
|
|
*
|
|
* Common mistakes & tips:
|
|
* * Don't just connect the IR LED directly to the pin, it won't
|
|
* have enough current to drive the IR LED effectively.
|
|
* * Make sure you have the IR LED polarity correct.
|
|
* See: https://learn.sparkfun.com/tutorials/polarity/diode-and-led-polarity
|
|
* * Typical digital camera/phones can be used to see if the IR LED is
|
|
* flashed. Replace the IR LED with a normal LED if you don't have a digital
|
|
* camera when debugging.
|
|
* * Avoid using the following pins unless you really know what you are doing:
|
|
* * Pin 0/D3: Can interfere with the boot/program mode & support circuits.
|
|
* * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will
|
|
* interfere.
|
|
* * Pin 3/RX/RXD0: Any serial transmissions to the ESP8266 will interfere.
|
|
* * ESP-01 modules are tricky. We suggest you use a module with more GPIOs
|
|
* for your first time. e.g. ESP-12 etc.
|
|
*/
|
|
|
|
#include <Arduino.h>
|
|
#include <IRremoteESP8266.h>
|
|
#include <IRsend.h>
|
|
|
|
// Codes are in Global Cache format less the emitter ID and request ID.
|
|
// These codes can be found in GC's Control Tower database.
|
|
|
|
uint16_t Samsung_power_toggle[71] = {
|
|
38000, 1, 1, 170, 170, 20, 63, 20, 63, 20, 63, 20, 20, 20, 20,
|
|
20, 20, 20, 20, 20, 20, 20, 63, 20, 63, 20, 63, 20, 20, 20,
|
|
20, 20, 20, 20, 20, 20, 20, 20, 20, 20, 63, 20, 20, 20, 20,
|
|
20, 20, 20, 20, 20, 20, 20, 20, 20, 63, 20, 20, 20, 63, 20,
|
|
63, 20, 63, 20, 63, 20, 63, 20, 63, 20, 1798};
|
|
|
|
#define IR_LED 4 // ESP8266 GPIO pin to use. Recommended: 4 (D2).
|
|
|
|
IRsend irsend(IR_LED); // Set the GPIO to be used to sending the message.
|
|
|
|
void setup() {
|
|
irsend.begin();
|
|
Serial.begin(115200);
|
|
}
|
|
|
|
void loop() {
|
|
Serial.println("Toggling power");
|
|
#if SEND_GLOBALCACHE
|
|
irsend.sendGC(Samsung_power_toggle, 71);
|
|
#else // SEND_GLOBALCACHE
|
|
Serial.println("Can't send because SEND_GLOBALCACHE has been disabled.");
|
|
#endif // SEND_GLOBALCACHE
|
|
delay(10000);
|
|
}
|