Tasmota/lib/libesp32/esp32-camera/driver/include/esp_camera.h

215 lines
7.5 KiB
C

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
/*
* Example Use
*
static camera_config_t camera_example_config = {
.pin_pwdn = PIN_PWDN,
.pin_reset = PIN_RESET,
.pin_xclk = PIN_XCLK,
.pin_sscb_sda = PIN_SIOD,
.pin_sscb_scl = PIN_SIOC,
.pin_d7 = PIN_D7,
.pin_d6 = PIN_D6,
.pin_d5 = PIN_D5,
.pin_d4 = PIN_D4,
.pin_d3 = PIN_D3,
.pin_d2 = PIN_D2,
.pin_d1 = PIN_D1,
.pin_d0 = PIN_D0,
.pin_vsync = PIN_VSYNC,
.pin_href = PIN_HREF,
.pin_pclk = PIN_PCLK,
.xclk_freq_hz = 20000000,
.ledc_timer = LEDC_TIMER_0,
.ledc_channel = LEDC_CHANNEL_0,
.pixel_format = PIXFORMAT_JPEG,
.frame_size = FRAMESIZE_SVGA,
.jpeg_quality = 10,
.fb_count = 2,
.grab_mode = CAMERA_GRAB_WHEN_EMPTY
};
esp_err_t camera_example_init(){
return esp_camera_init(&camera_example_config);
}
esp_err_t camera_example_capture(){
//capture a frame
camera_fb_t * fb = esp_camera_fb_get();
if (!fb) {
ESP_LOGE(TAG, "Frame buffer could not be acquired");
return ESP_FAIL;
}
//replace this with your own function
display_image(fb->width, fb->height, fb->pixformat, fb->buf, fb->len);
//return the frame buffer back to be reused
esp_camera_fb_return(fb);
return ESP_OK;
}
*/
#pragma once
#include "esp_err.h"
#include "driver/ledc.h"
#include "sensor.h"
#include "sys/time.h"
#ifdef __cplusplus
extern "C" {
#endif
/**
* @brief Configuration structure for camera initialization
*/
typedef enum {
CAMERA_GRAB_WHEN_EMPTY, /*!< Fills buffers when they are empty. Less resources but first 'fb_count' frames might be old */
CAMERA_GRAB_LATEST /*!< Except when 1 frame buffer is used, queue will always contain the last 'fb_count' frames */
} camera_grab_mode_t;
/**
* @brief Camera frame buffer location
*/
typedef enum {
CAMERA_FB_IN_PSRAM, /*!< Frame buffer is placed in external PSRAM */
CAMERA_FB_IN_DRAM /*!< Frame buffer is placed in internal DRAM */
} camera_fb_location_t;
/**
* @brief Configuration structure for camera initialization
*/
typedef struct {
int pin_pwdn; /*!< GPIO pin for camera power down line */
int pin_reset; /*!< GPIO pin for camera reset line */
int pin_xclk; /*!< GPIO pin for camera XCLK line */
int pin_sscb_sda; /*!< GPIO pin for camera SDA line */
int pin_sscb_scl; /*!< GPIO pin for camera SCL line */
int pin_d7; /*!< GPIO pin for camera D7 line */
int pin_d6; /*!< GPIO pin for camera D6 line */
int pin_d5; /*!< GPIO pin for camera D5 line */
int pin_d4; /*!< GPIO pin for camera D4 line */
int pin_d3; /*!< GPIO pin for camera D3 line */
int pin_d2; /*!< GPIO pin for camera D2 line */
int pin_d1; /*!< GPIO pin for camera D1 line */
int pin_d0; /*!< GPIO pin for camera D0 line */
int pin_vsync; /*!< GPIO pin for camera VSYNC line */
int pin_href; /*!< GPIO pin for camera HREF line */
int pin_pclk; /*!< GPIO pin for camera PCLK line */
int xclk_freq_hz; /*!< Frequency of XCLK signal, in Hz. EXPERIMENTAL: Set to 16MHz on ESP32-S2 or ESP32-S3 to enable EDMA mode */
ledc_timer_t ledc_timer; /*!< LEDC timer to be used for generating XCLK */
ledc_channel_t ledc_channel; /*!< LEDC channel to be used for generating XCLK */
pixformat_t pixel_format; /*!< Format of the pixel data: PIXFORMAT_ + YUV422|GRAYSCALE|RGB565|JPEG */
framesize_t frame_size; /*!< Size of the output image: FRAMESIZE_ + QVGA|CIF|VGA|SVGA|XGA|SXGA|UXGA */
int jpeg_quality; /*!< Quality of JPEG output. 0-63 lower means higher quality */
size_t fb_count; /*!< Number of frame buffers to be allocated. If more than one, then each frame will be acquired (double speed) */
camera_fb_location_t fb_location; /*!< The location where the frame buffer will be allocated */
camera_grab_mode_t grab_mode; /*!< When buffers should be filled */
} camera_config_t;
/**
* @brief Data structure of camera frame buffer
*/
typedef struct {
uint8_t * buf; /*!< Pointer to the pixel data */
size_t len; /*!< Length of the buffer in bytes */
size_t width; /*!< Width of the buffer in pixels */
size_t height; /*!< Height of the buffer in pixels */
pixformat_t format; /*!< Format of the pixel data */
struct timeval timestamp; /*!< Timestamp since boot of the first DMA buffer of the frame */
} camera_fb_t;
#define ESP_ERR_CAMERA_BASE 0x20000
#define ESP_ERR_CAMERA_NOT_DETECTED (ESP_ERR_CAMERA_BASE + 1)
#define ESP_ERR_CAMERA_FAILED_TO_SET_FRAME_SIZE (ESP_ERR_CAMERA_BASE + 2)
#define ESP_ERR_CAMERA_FAILED_TO_SET_OUT_FORMAT (ESP_ERR_CAMERA_BASE + 3)
#define ESP_ERR_CAMERA_NOT_SUPPORTED (ESP_ERR_CAMERA_BASE + 4)
/**
* @brief Initialize the camera driver
*
* @note call camera_probe before calling this function
*
* This function detects and configures camera over I2C interface,
* allocates framebuffer and DMA buffers,
* initializes parallel I2S input, and sets up DMA descriptors.
*
* Currently this function can only be called once and there is
* no way to de-initialize this module.
*
* @param config Camera configuration parameters
*
* @return ESP_OK on success
*/
esp_err_t esp_camera_init(const camera_config_t* config);
/**
* @brief Deinitialize the camera driver
*
* @return
* - ESP_OK on success
* - ESP_ERR_INVALID_STATE if the driver hasn't been initialized yet
*/
esp_err_t esp_camera_deinit();
/**
* @brief Obtain pointer to a frame buffer.
*
* @return pointer to the frame buffer
*/
camera_fb_t* esp_camera_fb_get();
/**
* @brief Return the frame buffer to be reused again.
*
* @param fb Pointer to the frame buffer
*/
void esp_camera_fb_return(camera_fb_t * fb);
/**
* @brief Get a pointer to the image sensor control structure
*
* @return pointer to the sensor
*/
sensor_t * esp_camera_sensor_get();
/**
* @brief Save camera settings to non-volatile-storage (NVS)
*
* @param key A unique nvs key name for the camera settings
*/
esp_err_t esp_camera_save_to_nvs(const char *key);
/**
* @brief Load camera settings from non-volatile-storage (NVS)
*
* @param key A unique nvs key name for the camera settings
*/
esp_err_t esp_camera_load_from_nvs(const char *key);
#ifdef __cplusplus
}
#endif
#include "img_converters.h"