mirrors
/
Tasmota
mirror of https://github.com/arendst/Tasmota.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

Updated LM75AD (markdown)

andrethomas 2018-07-06 18:13:27 +02:00
parent 519aac9fd8
commit bb4983474b
1 changed files with 39 additions and 5 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

44
LM75AD.md

@ -1,14 +1,48 @@
LM75AD I2C Temperature Sensor # LM75AD I2C Temperature Sensor
### Features
* Pin-for-pin replacement for industry standard LM75 and offers improved temperature resolution of 0.125°C and Specification of a single part over power supply range from 2.8 V to 5.5 V
* Small 8-pin package types: SO8 and TSSOP8
* I2C-bus interface with up to 8 devices on the same bus
* Power supply range from 2.8 V to 5.5 V _**(Note that for use the ESP8266 you must limit this to 3.3V as the GPIO pins of the ESP8266 are not 5V tolerant)**_
* Temperatures range from −55°C to +125°C
* 11-bit ADC that offers a temperature resolution of 0.125°C
* Temperature accuracy of:
* ±2°C from −25°C to +100°C
* ±3°C from −55°C to +125°C
* Programmable temperature threshold and hysteresis set points _**(Not used in the LM75AD driver at this stage)**_
* Supply current of 3.5μA in shutdown mode for power conservation
* Stand-alone operation as thermostat at power-up _**(Not used in the LM75AD driver at this stage)**_
* ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101
* Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
Datasheet can be found at [https://www.nxp.com/docs/en/data-sheet/LM75A.pdf](https://www.nxp.com/docs/en/data-sheet/LM75A.pdf)
Breakout boards available typically look like this Breakout boards available typically look like this
Top:
![LM75AD_TOP](https://github.com/andrethomas/images/raw/master/lm75ad/board_lm75ad_top.png) ![LM75AD_TOP](https://github.com/andrethomas/images/raw/master/lm75ad/board_lm75ad_top.png)
Bottom:
![LM75AD_BOTTOM](https://github.com/andrethomas/images/raw/master/lm75ad/board_lm75ad_bot.png) ![LM75AD_BOTTOM](https://github.com/andrethomas/images/raw/master/lm75ad/board_lm75ad_bot.png)
Can also be used standalone if soldered to a board given the diagram is used
![Circuit](https://github.com/andrethomas/images/raw/master/lm75ad/SimpleCircuit.png)
### Hardware Configuration
For connection to the ESP8266 I2C bus it is important to connect the SCL and SDA pins according to how the Sonoff firmware was configured.
The driver must be enabled in the firmware's user_config.h file by ensuring that the USE_I2C and USE_LM75AD lines are uncommented.
The driver currently only allows the use of a single LM75AD sensor on any of the addresses configurable through pins A0, A1 and A2 - These are usually conveniently broken out on a breakout board either as pins or as solderable joins as can be seen on the example breakout board provided in the images above.
These pins need to be either tied down to GND or VCC (3.3V) and the resulting I2C address will be set during power-up according to the datasheet as follows
![Address MAP](https://github.com/andrethomas/images/raw/master/lm75ad/Address_Map.png)
### Expected Behaviour
Once connected correctly (be it using a breakout board or just manually soldered) the Sonoff Tasmota firmware should detect the sensor automatically and start pushing out telemetry data.