Updated Commands (markdown)

Commands.md

@@ -291,7 +291,7 @@ Sensor13<a id="Sensor13"></a>|**5.12.0**<BR>[INA219](http://www.ti.com/product/I
 Sensor15<a id="Sensor15"></a>|**5.12.0**<BR>[Automatic Baseline Correction](https://github.com/arendst/Sonoff-Tasmota/blob/c97ea4d9176eb7e87abff5f963a0f1c60f0a5e52/sonoff/xsns_15_mhz19.ino#L47) for [MH-Z19B](MH-Z19B) CO<sub>2</sub> sensor<BR>`0` = disabled<BR>`1` = enabled *(default)*<BR>`2` = disable and start manual calibration from 400 ppm of CO<sub>2</sub><BR>`9` = reset sensor to factory defaults<BR>`1000` = sets measurement range to 1000ppm CO<sub>2</sub><BR>`2000` = sets measurement range to 2000ppm CO<sub>2</sub><BR>`3000` = sets measurement range to 3000ppm CO<sub>2</sub><BR>`5000` = sets measurement range to 5000ppm CO<sub>2</sub>
 Sensor20<a id="Sensor20"></a>|**6.6.0**<BR>[Nova Fitness SDS011](Wemos-D1-Mini-and-Nova-Fitness-SDS011-Laser-Dust-Sensor) dust sensor.<BR>`1..255` = change working period in minutes
 Sensor27<a id="Sensor27"></a>|[APDS-9960](APDS-9960) sensor commands<BR>`0` = enable light level and proximity sensor / disable gestures *(default)* <BR> `1` = enable gesture mode/ disable light level and proximity sensor<BR> `2` = enable gestures with half gain / disable light and proximity sensor<BR>`3..255` = Set [ATIME register](APDS-9960#known-issues) for different integration times
-Sensor29<a id="Sensor29"></a>|MCP23008 / MCP23017 I<sup>2</sup>C GPIO Expander configuration ([additional details](MCP23008-MCP23017))<BR>`Reset<x>` = reset all pins<BR>x = `1..5`<BR>`1` = INPUT mode, no reporting, no pull-up<BR>`2` = INPUT mode, report on CHANGE, pull-up enabled<BR>`3` = INPUT mode, report on LOW, pull-up enabled<BR>`4` = INPUT mode, report on HIGH, pull-up enabled<BR>`5` = OUTPUT mode (if enabled by #define USE_MCP230xx_OUTPUT)<BR><BR>`pin,pinmode{,intpullup\|outstate{,repmode}}`<ul></ul>`pin` = the I/O pin on the MCP230xx chip<ul><li>`0..7` for MCP23008</li><li>`0..15` for the MCP23017)</ul>`pinmode` = operational mode of the pin (`?, 0..5`)<ul><li>`?` = query pin configuration</li><li>`0` = Disabled (deprecated, but will be default for previously unconfigured devices)</li><li>`1` = INPUT (Floating - only telemetry data will be sent according to configuration `TelePeriod` intervals)</li><li>`2` = INPUT with INTERRUPT on CHANGE (will send an MQTT output on state change from LOW to HIGH **and** HIGH to LOW)</li><li>`3` = INPUT with INTERRUPT on CHANGE to **LOW** (will send an MQTT output on state change **only** from HIGH to LOW)</li><li>`4` = INPUT with INTERRUPT on CHANGE to **HIGH** (will send an MQTT output on state change **only** from LOW to HIGH)</li><li>`5` = OUTPUT (if enabled with `#define USE_MCP230xx_OUTPUT`)</li></ul>`intpullup` *(pinmode `1..4`)*. Pull-up resistors are disabled by default for pin mode `1` whilst enabled by default for pin modes `2..4` (because they are interrupt enabled pins and we do not want signal bounce). The internal pull-up on these pins may be disabled if necessary if you are biasing them externally.<ul><li>`0` = weak internal pull-up disabled *(default for pinmode `1`)*</li><li>`1` = weak internal pull-up enabled *(default for pinmode `2..4`)*</li></ul>`outstate` *(pinmode `5..6`)* = set the default state of an OUTPUT pin on reset/power-up. If your device is configured to save state (`SetOption0 = 1`), the `outstate` setting will be ignored and the last known state of the pin will be applied during power-up/reset.<ul><li>`0/off` = set output pin to OFF</li><li>`1/on` = set output pin state to ON</li></ul>`repmode` = reporting mode (optional). Interrupt mode is disabled for pinmode `1` and for output pinmodes (`5..6`)<ul><li>`0` = interrupt using Event and report using telemetry *(default for pinmode `2..4`)*</li><li>`1` = interrupt using Event only (no telemetry reported)</li><li>`2` = report using telemetry only (no Event triggered)</li></ul>
+Sensor29<a id="Sensor29"></a>|MCP23008 / MCP23017 I<sup>2</sup>C GPIO Expander configuration ([additional details](MCP23008-MCP23017))<BR>`Reset<x>` = reset all pins<BR>x = `1..5`<BR>`1` = INPUT mode, no reporting, no pull-up<BR>`2` = INPUT mode, report on CHANGE, pull-up enabled<BR>`3` = INPUT mode, report on LOW, pull-up enabled<BR>`4` = INPUT mode, report on HIGH, pull-up enabled<BR>`5` = OUTPUT mode (if enabled by #define USE_MCP230xx_OUTPUT)<BR><BR>`pin,pinmode{,intpullup\|outstate{,repmode}}`<ul></ul>`pin` = the I/O pin on the MCP230xx chip<ul><li>`0..7` for MCP23008</li><li>`0..15` for the MCP23017)</ul>`pinmode` = operational mode of the pin (`?, 0..5`)<ul><li>`?` = query pin configuration</li><li>`0` = Disabled (deprecated, but will be default for previously unconfigured devices)</li><li>`1` = INPUT (Floating - only telemetry data will be sent according to configuration `TelePeriod` intervals)</li><li>`2` = INPUT with INTERRUPT on CHANGE (will send an MQTT output on state change from LOW to HIGH **and** HIGH to LOW)</li><li>`3` = INPUT with INTERRUPT on CHANGE to **LOW** (will send an MQTT output on state change **only** from HIGH to LOW)</li><li>`4` = INPUT with INTERRUPT on CHANGE to **HIGH** (will send an MQTT output on state change **only** from LOW to HIGH)</li><li>`5` = OUTPUT (if enabled with `#define USE_MCP230xx_OUTPUT`)</li></ul>`intpullup` *(pinmode `1..4`)*. Pull-up resistors are disabled by default for pin mode `1` whilst enabled by default for pin modes `2..4` (because they are interrupt enabled pins and we do not want signal bounce). The internal pull-up on these pins may be disabled if necessary if you are biasing them externally.<ul><li>`0` = weak internal pull-up disabled *(default for pinmode `1`)*</li><li>`1` = weak internal pull-up enabled *(default for pinmode `2..4`)*</li></ul>`outstate` *(pinmode `5..6`)* = set the default state of an OUTPUT pin on reset/power-up. If your device is configured to save state (`SetOption0 = 1`), the `outstate` setting will be ignored and the last known state of the pin will be applied during power-up/reset.<ul><li>`0/off` = set output pin to OFF</li><li>`1/on` = set output pin state to ON</li><li>`2/toggle` = toggle output pin state</li></ul>`repmode` = reporting mode (optional). Interrupt mode is disabled for pinmode `1` and for output pinmodes (`5..6`)<ul><li>`0` = interrupt using Event and report using telemetry *(default for pinmode `2..4`)*</li><li>`1` = interrupt using Event only (no telemetry reported)</li><li>`2` = report using telemetry only (no Event triggered)</li></ul>
 Sensor34<a id="Sensor34"></a>|**6.6.0**<BR>[HX711 load cell](https://github.com/bogde/HX711) sensor calibration<BR>`1` = reset display to 0<BR>`2` = start calibration<BR>`2` `<value>` = set reference weight in grams and start calibration<BR>`3` = show reference weight in grams<BR>`3` `<value>` = set reference weight in grams<BR>`4` = show calibrated scale value<BR>`4` `<value>` = set calibrated scale value<BR>`5` = show max weight in gram<BR>`5` `<value>` = set max weight in grams<BR>`6` = show single item weight in grams<BR>`6` `<value>` = set single item weight in grams. Once the item weight is set, when items are added to the scale, the telemetry message will report `Count` as the number of items on the scale<BR>`7` = save current weight to be used as start weight on restart<BR>`8` `0/1` **6.6.0.13**<BR>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;`0` = disable JSON message on weight change over 4 grams<BR>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;`1` = enable JSON message on weight change over 4 grams
 Sensor53<a id="Sensor53"></a>|[Smart Meter Interface](Smart-Meter-Interface)<BR>`r` = reset the driver with a new descriptor specified with the Tasmota [Scripting](Scripting-Language) language.<BR>`c<x> <value>` = preset counter (x = `1..5`) to `value` when the driver is set to counter mode<BR>`d<x>` = disable data decoding and dump meter (x = `1..5`) data to the Console. This is used to decipher the meter's data format to define the variable encoding in the meter's descriptor.<BR>`d0` = disable data dump mode and revert to decoding mode.
 TempRes<a id="TempRes"></a>|Temperature sensor resolution<BR>`0..3` = maximum number of decimal places