mirrors
/
Tasmota
mirror of https://github.com/arendst/Tasmota.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

Updated Sonoff TX T0 Touch 1CH 2CH 3CH US (markdown)

Michael Ingraham 2019-07-25 11:37:16 -04:00
parent 402b37a254
commit c90ce980fb
1 changed files with 20 additions and 22 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

44
Sonoff-TX-T0-Touch-1CH-2CH-3CH----US.md

@ -1,35 +1,33 @@
these were purchased (mix of 1-3 ch) 06/2019 and come with Sonoff v3.3.0 stock firmware. i believe OTA (sonOTA) doesnt work on this ver so serial flash it is. June 2019 - Devices delivered with Sonoff v3.3.0 stock firmware.
board label: T0US TOUCH v1.0 2008.11.15 Serial flashing works for this device. You may wish to check whether the [Sonoff DIY](Sonoff-DIY) flashing method works if this device is upgraded to v3.3.1.
Board label: `T0US TOUCH v1.0 2008.11.15`
* TX T0 US, 1-3CH boards are physically the same. * TX T0 US, 1-3CH boards are physically the same.
* Only need the "top board" to flash (not the bottom relay part) -- don't power with mains (you can't if you only use top anyway)
* only need the "top board" to flash (not the bottom relay part) -- dont power with main (you cant if you only use top anyway) * R19 is tied to GPIO 0 to enter flash mode, just like on T1 but in a different spot for t0 (or US?).
- Find the C2 (j1) pins and look directly up about half inch for r19
* R19 is tied to GPIO 0 to enter flash mode, just like on T1 but in a different spot for t0 (or us?). * Ensure that you select 3.3v and **not 5v!** to flash the board.
find the C2 (j1) pins and look directly up about half inch for r19 * ESP8285 - 1M - DOUT - erase flash - 115200 baud
* my usb adaptor has 3v3 pin make sure to use this not 5v! your usb adaptor will power the board for flash.
* esp8285 - 1M - DOUT - erase flash - 115200 baud
Like the T1, this does not have enough room to solder a header on. Like the T1, this does not have enough room to solder a header on.
Use a piece of thick cardboard to lay your top board on. Firmly press some jumpers through the serial holes into the cardboard. Use a piece of thick cardboard to lay your top board on. Firmly press some jumpers through the serial holes into the cardboard.
If you push these through at an angle will be good enough to make contact to connect to your serial adaptor, trial and error but is not hard. pic attached.
regular flashing steps apply, connect Ground, Vcc TX, RX to your serial adaptor. paying attention to tx/rx! If you push these through at an angle will be good enough to make contact to connect to your serial adaptor, trial and error but is not hard. See photo below.
for flash mode i use another jumper through the ground hole on the C2 pins (left of the serial and label J1). same, push jumper through cardboard to secure it. Regular flashing steps apply: connect Ground, Vcc TX, RX to your serial adaptor. Pay attention to TX/RX!
While powered off hold the other end of jumper to R19 and then power up (plug in your usb serial adaptor).
hold it for about 3 seconds after it powers up and remove it.
you should not see the network status led flash anymore, then you know you're in flash mode. If its flashing power off and try again.
Using the TX T1 1-3 template is fine although i have created a T0 template to look nicer. will update that asap. For flash mode, use another jumper through the ground hole on the C2 pins (left of the serial and label J1). Same as above, push the jumper through cardboard to secure it.
While powered off hold the other end of jumper to R19 and then power up (plug in your USB serial adaptor).
Hold it for 3-5 seconds after it powers up before removing it.
You should not see the network status led flash anymore, then you know you're in flash mode. If its flashing power off and try again.
Using the TX T1 1-3 device template will work. A new T0 template is forthcoming.
![image](https://user-images.githubusercontent.com/52976730/61833228-9c4e5f80-ae41-11e9-909b-1ea5d10f9deb.png) ![image](https://user-images.githubusercontent.com/52976730/61833228-9c4e5f80-ae41-11e9-909b-1ea5d10f9deb.png)
![image](https://user-images.githubusercontent.com/52976730/61833325-f3eccb00-ae41-11e9-896a-4e9ebe4f47d9.png) ![image](https://user-images.githubusercontent.com/52976730/61833325-f3eccb00-ae41-11e9-896a-4e9ebe4f47d9.png)
Thank you
Matt