mirror of https://github.com/arendst/Tasmota.git
Updated Hardware Preparation (markdown)
parent
ce8088c2d1
commit
dfc6454009
|
@ -41,38 +41,13 @@ If everything went well, you are now in Flash Mode and ready to continue with th
|
||||||
|
|
||||||
Check the module specific instructions and restrictions documented in the **device specific articles linked in the menu on the right** 🡺
|
Check the module specific instructions and restrictions documented in the **device specific articles linked in the menu on the right** 🡺
|
||||||
|
|
||||||
<!--
|
* [Sonoff Basic](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Basic#serial-connection)
|
||||||
* [Sonoff Dual](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Dual)
|
* [Sonoff Dual](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Dual)
|
||||||
|
* [Sonoff RF](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-RF#serial-connection)
|
||||||
* [Sonoff Pow](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Pow)
|
* [Sonoff Pow](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Pow)
|
||||||
* [Sonoff Touch](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Touch)
|
* [Sonoff Touch](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Touch)
|
||||||
* [Sonoff 4CH / 4CH Pro](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-4CH-and-4CH-Pro)
|
* [Sonoff 4CH / 4CH Pro](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-4CH-and-4CH-Pro)
|
||||||
-->
|
|
||||||
|
|
||||||
----
|
|
||||||
----
|
|
||||||
|
|
||||||
### S20 Smart Socket
|
|
||||||
|
|
||||||
<img alt="S20 Smart Socket" src="https://github.com/arendst/arendst.github.io/blob/master/media/s20b.jpg" width="230" align="right" />
|
|
||||||
The picture shows how to program the S20 Smart Socket powered by the FTDI USB converter. With newer US sockets, either use a right-angle header, or remove the header after flashing. Otherwise, the pushbutton may rub against a pin and get stuck.
|
|
||||||
<br />
|
|
||||||
<br />
|
|
||||||
<br />
|
|
||||||
<br />
|
|
||||||
|
|
||||||
### Sonoff RF
|
|
||||||
|
|
||||||
The Sonoff RF needs some tweaking as the connection needed during programming between the button and GPIO0 might not be present.
|
|
||||||
|
|
||||||
[Phalox](http://phalox.be/wp/electronics/itead-sonoff-slampher-custom-firmware-fix/) explains the case with a picture where you have to install a jumper wire for R21. I received the same result using a small screwdriver and shorting both solder pads of R21 while holding down the button during programming.
|
|
||||||
|
|
||||||
<img alt="S20 Smart Socket" src="https://github.com/arendst/arendst.github.io/blob/master/media/sonoffrffix.jpg" width="230" align="right" />
|
|
||||||
|
|
||||||
Pairing the iTead RF remote controller is the same as with the original iTead software:
|
|
||||||
- two short button presses will blink a red led shortly and start RF signal recognition. Three longer blinks signal RF reception.
|
|
||||||
- three short button presses will keep the red led on for some seconds and erase the known RF code.
|
|
||||||
|
|
||||||
I was unable to pair the Sonoff RF 434MHz receiver with my KaKu switches but the iTead provided remote control works just fine.
|
|
||||||
|
|
||||||
### Motor Clockwise/Anticlockwise
|
### Motor Clockwise/Anticlockwise
|
||||||
|
|
||||||
|
|
Loading…
Reference in New Issue