mirrors
/
Tasmota
mirror of https://github.com/arendst/Tasmota.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

Updated Hardware Preparation (markdown)

Andreas Hubel 2017-11-29 19:52:01 +01:00
parent ce8088c2d1
commit dfc6454009
1 changed files with 3 additions and 28 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

31
Hardware-Preparation.md

@ -41,38 +41,13 @@ If everything went well, you are now in Flash Mode and ready to continue with th
Check the module specific instructions and restrictions documented in the **device specific articles linked in the menu on the right** 🡺
<!--
* [Sonoff Basic](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Basic#serial-connection)
* [Sonoff Dual](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Dual)
* [Sonoff RF](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-RF#serial-connection)
* [Sonoff Pow](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Pow)
* [Sonoff Touch](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-Touch)
* [Sonoff 4CH / 4CH Pro](https://github.com/arendst/Sonoff-Tasmota/wiki/Sonoff-4CH-and-4CH-Pro)
-->
----
----
### S20 Smart Socket
<img alt="S20 Smart Socket" src="https://github.com/arendst/arendst.github.io/blob/master/media/s20b.jpg" width="230" align="right" />
The picture shows how to program the S20 Smart Socket powered by the FTDI USB converter. With newer US sockets, either use a right-angle header, or remove the header after flashing. Otherwise, the pushbutton may rub against a pin and get stuck.
<br />
<br />
<br />
<br />
### Sonoff RF
The Sonoff RF needs some tweaking as the connection needed during programming between the button and GPIO0 might not be present.
[Phalox](http://phalox.be/wp/electronics/itead-sonoff-slampher-custom-firmware-fix/) explains the case with a picture where you have to install a jumper wire for R21. I received the same result using a small screwdriver and shorting both solder pads of R21 while holding down the button during programming.
<img alt="S20 Smart Socket" src="https://github.com/arendst/arendst.github.io/blob/master/media/sonoffrffix.jpg" width="230" align="right" />
Pairing the iTead RF remote controller is the same as with the original iTead software:
- two short button presses will blink a red led shortly and start RF signal recognition. Three longer blinks signal RF reception.
- three short button presses will keep the red led on for some seconds and erase the known RF code.
I was unable to pair the Sonoff RF 434MHz receiver with my KaKu switches but the iTead provided remote control works just fine.
### Motor Clockwise/Anticlockwise
@ -96,4 +71,4 @@ Don't forget to reconnect the TX jumper after flashing ;)
<img alt="SonoffSC" src="https://puu.sh/vZZRI/ff36ff9244.jpg" width="230" />
<img alt="SonoffScRemoveTX" src="https://puu.sh/vZZSi/43244f3cc1.jpg" width="230" />
<img alt="SonoffSCButoom" src="https://puu.sh/vZZSC/aaa140afa3.jpg" width="130" />
<img alt="SonoffSCButoom" src="https://puu.sh/vZZSC/aaa140afa3.jpg" width="130" />