mirrors
/
micropython
mirror of https://github.com/micropython/micropython.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
micropython/stmhal/boards/ESPRUINO_PICO/mpconfigboard.h

70 lines
2.4 KiB
C
Raw Normal View History

stmhal: Add support for Espruino Pico board. To build: make BOARD=ESPRUINO_PICO To deploy: short the BOOT0/BTN contact on the back of the board (eg by drawing over it with a graphite pencil), then hold down BTN while inserting the board into the USB port. The board should then enter DFU mode, and the firmware can be downloaded using: make BOARD=ESPRUINO_PICO deploy
2015-04-18 21:27:10 +01:00
#define MICROPY_HW_BOARD_NAME "Espruino Pico"
#define MICROPY_HW_MCU_NAME "STM32F401CD"
stmhal: Disable network and usocket for ESPRUINO_PICO
2016-10-05 06:10:44 +01:00
#define MICROPY_PY_USOCKET (0)
#define MICROPY_PY_NETWORK (0)
stmhal: Add support for Espruino Pico board. To build: make BOARD=ESPRUINO_PICO To deploy: short the BOOT0/BTN contact on the back of the board (eg by drawing over it with a graphite pencil), then hold down BTN while inserting the board into the USB port. The board should then enter DFU mode, and the firmware can be downloaded using: make BOARD=ESPRUINO_PICO deploy
2015-04-18 21:27:10 +01:00
#define MICROPY_HW_HAS_SWITCH (1)
stmhal/diskio: Introduce MICROPY_HW_HAS_FLASH setting. To allow to reuse stmhal/diskio for ports which don't have flash but have other storage devices.
2016-02-06 12:48:58 +00:00
#define MICROPY_HW_HAS_FLASH (1)
stmhal: Add support for Espruino Pico board. To build: make BOARD=ESPRUINO_PICO To deploy: short the BOOT0/BTN contact on the back of the board (eg by drawing over it with a graphite pencil), then hold down BTN while inserting the board into the USB port. The board should then enter DFU mode, and the firmware can be downloaded using: make BOARD=ESPRUINO_PICO deploy
2015-04-18 21:27:10 +01:00
#define MICROPY_HW_HAS_SDCARD (0)
#define MICROPY_HW_HAS_MMA7660 (0)
#define MICROPY_HW_HAS_LIS3DSH (0)
#define MICROPY_HW_HAS_LCD (0)
#define MICROPY_HW_ENABLE_RNG (0)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_TIMER (1)
#define MICROPY_HW_ENABLE_SERVO (1)
#define MICROPY_HW_ENABLE_DAC (0)
#define MICROPY_HW_ENABLE_CAN (0)
// Pico has an 8 MHz HSE and the F401 does 84 MHz max
#define MICROPY_HW_CLK_PLLM (5)
#define MICROPY_HW_CLK_PLLN (210)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV4)
#define MICROPY_HW_CLK_PLLQ (7)
// does not have a 32kHz crystal
#define MICROPY_HW_RTC_USE_LSE (0)
stmhal: Allow to configure UART pins completely via mpconfigboard.h.
2015-05-02 17:31:39 +01:00
// UART config
stmhal: Refactor UART configuration to use pin objects. This follows the pattern of other peripherals (I2C, SPI) to specify the pins using pin objects instead of a pair of GPIO port and pin number. It makes it easier to customise the UART pins for a particular board.
2016-12-05 01:21:45 +00:00
#define MICROPY_HW_UART1_TX (pin_B6)
#define MICROPY_HW_UART1_RX (pin_B7)
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART2_RTS (pin_A1)
#define MICROPY_HW_UART2_CTS (pin_A0)
#define MICROPY_HW_UART6_TX (pin_A11)
#define MICROPY_HW_UART6_RX (pin_A12)
stmhal: Allow to configure UART pins completely via mpconfigboard.h.
2015-05-02 17:31:39 +01:00
stmhal: Add support for Espruino Pico board. To build: make BOARD=ESPRUINO_PICO To deploy: short the BOOT0/BTN contact on the back of the board (eg by drawing over it with a graphite pencil), then hold down BTN while inserting the board into the USB port. The board should then enter DFU mode, and the firmware can be downloaded using: make BOARD=ESPRUINO_PICO deploy
2015-04-18 21:27:10 +01:00
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B3)
#define MICROPY_HW_I2C3_SCL (pin_A8)
#define MICROPY_HW_I2C3_SDA (pin_B4)
stmhal: For SPI config, use HW_SPIx_SCK instead of HW_ENABLE_SPIx. Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI and NSS. This makes it the same as how I2C is configured.
2015-12-12 15:02:02 +00:00
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
stmhal: Add support for Espruino Pico board. To build: make BOARD=ESPRUINO_PICO To deploy: short the BOOT0/BTN contact on the back of the board (eg by drawing over it with a graphite pencil), then hold down BTN while inserting the board into the USB port. The board should then enter DFU mode, and the firmware can be downloaded using: make BOARD=ESPRUINO_PICO deploy
2015-04-18 21:27:10 +01:00
// BTN1 has no pullup or pulldown; it is active high and broken out on a header
#define MICROPY_HW_USRSW_PIN (pin_C13)
#define MICROPY_HW_USRSW_PULL (GPIO_PULLDOWN)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// Pico has 2 LEDs
#define MICROPY_HW_LED1 (pin_B2) // red
#define MICROPY_HW_LED2 (pin_B12) // green
#define MICROPY_HW_LED3 (pin_B12) // green
#define MICROPY_HW_LED4 (pin_B12) // green
stmhal/led: Refactor LED to use mp_hal_pin_output() init function. As part of this patch the MICROPY_HW_LED_OTYPE setting is removed because it is now unused (all boards anyway had this as OUTPUT_PP).
2016-10-18 04:43:05 +01:00
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))