micropython/ports/stm32/boards/NUCLEO_F091RC/mpconfigboard.h

#define MICROPY_HW_BOARD_NAME       "NUCLEO-F091RC"
#define MICROPY_HW_MCU_NAME         "STM32F091RCT6"

#define MICROPY_EMIT_THUMB          (0)
#define MICROPY_EMIT_INLINE_THUMB   (0)
#define MICROPY_PY_USOCKET          (0)
#define MICROPY_PY_NETWORK          (0)
#define MICROPY_PY_STM              (0)
#define MICROPY_PY_PYB_LEGACY       (0)

#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
#define MICROPY_HW_ENABLE_RTC       (1)
#define MICROPY_HW_ENABLE_ADC       (1)
#define MICROPY_HW_ENABLE_DAC       (1)
#define MICROPY_HW_ENABLE_TIMER     (1)
#define MICROPY_HW_HAS_SWITCH       (1)

// For system clock, enable one source:
//#define MICROPY_HW_CLK_USE_HSI      (1) // internal 8MHz -> PLL = 48MHz.
#define MICROPY_HW_CLK_USE_HSI48    (1) // internal 48MHz.
//#define MICROPY_HW_CLK_USE_HSE      (1) // external crystal -> PLL = 48MHz.
// For HSE set the crystal / clock input frequency HSE_VALUE in stm32f0xx_hal_conf.h
#if MICROPY_HW_CLK_USE_HSE
#define MICROPY_HW_CLK_USE_BYPASS   (1) // HSE comes from STLINK 8MHz, not crystal.
#endif

// The board has an external 32kHz crystal
#define MICROPY_HW_RTC_USE_LSE      (1)

// UART config
#define MICROPY_HW_UART1_TX     (pin_B6)
#define MICROPY_HW_UART1_RX     (pin_B7)
#define MICROPY_HW_UART2_TX     (pin_A2)
#define MICROPY_HW_UART2_RX     (pin_A3)
#define MICROPY_HW_UART3_TX     (pin_C10)
#define MICROPY_HW_UART3_RX     (pin_C11)
#define MICROPY_HW_UART4_TX     (pin_A0)
#define MICROPY_HW_UART4_RX     (pin_A1)
#define MICROPY_HW_UART5_TX     (pin_B3)
#define MICROPY_HW_UART5_RX     (pin_B4)
#define MICROPY_HW_UART6_TX     (pin_C0)
#define MICROPY_HW_UART6_RX     (pin_C1)
#define MICROPY_HW_UART7_TX     (pin_C6)
#define MICROPY_HW_UART7_RX     (pin_C7)
#define MICROPY_HW_UART8_TX     (pin_C2)
#define MICROPY_HW_UART8_RX     (pin_C3)

// USART2 is connected to the ST-LINK USB VCP
#define MICROPY_HW_UART_REPL PYB_UART_2
#define MICROPY_HW_UART_REPL_BAUD 115200

// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B8)        // Arduino D15, pin 3 on CN10
#define MICROPY_HW_I2C1_SDA (pin_B9)        // Arduino D14, pin 5 on CN10
#define MICROPY_HW_I2C2_SCL (pin_B10)       // Arduino D6,  pin 25 on CN10
#define MICROPY_HW_I2C2_SDA (pin_B11)       //              pin 18 on CN10

// SPI busses
#define MICROPY_HW_SPI1_NSS     (pin_A15)   //              pin 17 on CN7
#define MICROPY_HW_SPI1_SCK     (pin_A5)    // Arduino D13, pin 11 on CN10
#define MICROPY_HW_SPI1_MISO    (pin_A6)    // Arduino D12, pin 13 on CN10
#define MICROPY_HW_SPI1_MOSI    (pin_A7)    // Arduino D11, pin 15 on CN10
#define MICROPY_HW_SPI2_NSS     (pin_B12)   //              pin 16 on CN10
#define MICROPY_HW_SPI2_SCK     (pin_B13)   //              pin 30 on CN10
#define MICROPY_HW_SPI2_MISO    (pin_B14)   //              pin 28 on CN10
#define MICROPY_HW_SPI2_MOSI    (pin_B15)   //              pin 26 on CN10

// USER B1 has a pull-up and is active low
#define MICROPY_HW_USRSW_PIN        (pin_C13)
#define MICROPY_HW_USRSW_PULL       (0)
#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED    (0)

// NUCLEO-64 has one user LED
#define MICROPY_HW_LED1             (pin_A5) // green
#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))