micropython/ports/stm32/boards/NUCLEO_L073RZ/mpconfigboard.h

Ignoring revisions in .git-blame-ignore-revs. Click here to bypass and see the normal blame view.

57 lines
2.1 KiB
C
Raw Normal View History

/* This file is part of the MicroPython project, http://micropython.org/
* MIT License; Copyright (c) 2019 Damien P. George
*/
#define MICROPY_HW_BOARD_NAME "NUCLEO-L073RZ"
#define MICROPY_HW_MCU_NAME "STM32L073RZT6"
#define MICROPY_EMIT_THUMB (0)
#define MICROPY_EMIT_INLINE_THUMB (0)
#define MICROPY_PY_BUILTINS_COMPLEX (0)
#define MICROPY_PY_GENERATOR_PEND_THROW (0)
#define MICROPY_PY_MATH (0)
#define MICROPY_PY_FRAMEBUF (0)
#define MICROPY_PY_USOCKET (0)
#define MICROPY_PY_NETWORK (0)
#define MICROPY_PY_ONEWIRE (0)
#define MICROPY_PY_STM (0)
#define MICROPY_PY_PYB_LEGACY (0)
#define MICROPY_PY_UHEAPQ (0)
#define MICROPY_PY_UTIMEQ (0)
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_ADC (0)
#define MICROPY_HW_HAS_SWITCH (1)
// UART config
#define MICROPY_HW_UART1_TX (pin_B6)
#define MICROPY_HW_UART1_RX (pin_B7)
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
// USART2 is connected to the ST-LINK USB VCP
#define MICROPY_HW_UART_REPL PYB_UART_2
#define MICROPY_HW_UART_REPL_BAUD 115200
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B8) // Arduino D15, pin 3 on CN10
#define MICROPY_HW_I2C1_SDA (pin_B9) // Arduino D14, pin 5 on CN10
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A15) // pin 17 on CN7
#define MICROPY_HW_SPI1_SCK (pin_A5) // Arduino D13, pin 11 on CN10
#define MICROPY_HW_SPI1_MISO (pin_A6) // Arduino D12, pin 13 on CN10
#define MICROPY_HW_SPI1_MOSI (pin_A7) // Arduino D11, pin 15 on CN10
// USER B1 has a pull-up and is active low
#define MICROPY_HW_USRSW_PIN (pin_C13)
#define MICROPY_HW_USRSW_PULL (0)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// NUCLEO-64 has one user LED
#define MICROPY_HW_LED1 (pin_A5) // green
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))