micropython/docs/library/machine.SPI.rst

107 lines
3.9 KiB
ReStructuredText
Raw Normal View History

.. currentmodule:: machine
class SPI -- a Serial Peripheral Interface bus protocol
=======================================================
SPI is a serial protocol that is driven by a master. At the physical level,
bus consistens of 3 lines: SCK, MOSI, MISO. Multiple devices can share the
same bus. Each device should have a separate, 4th signal, SS (Slave Select),
to select a particualr device on a bus with which communication takes place.
Management of an SS signal should happen in user code (via machine.Pin class).
.. only:: port_wipy
See usage model of I2C; SPI is very similar. Main difference is
parameters to init the SPI bus::
from machine import SPI
spi = SPI(0, mode=SPI.MASTER, baudrate=1000000, polarity=0, phase=0, firstbit=SPI.MSB)
Only required parameter is mode, must be SPI.MASTER. Polarity can be 0 or
1, and is the level the idle clock line sits at. Phase can be 0 or 1 to
sample data on the first or second clock edge respectively.
Constructors
------------
.. class:: SPI(id, ...)
Construct an SPI object on the given bus, ``id``. Values of ``id`` depend
on a particular port and its hardware. Values 0, 1, etc. are commonly used
to select hardware SPI block #0, #1, etc. Value -1 can be used for
bitbanging (software) implementation of SPI (if supported by a port).
With no additional parameters, the SPI object is created but not
initialised (it has the settings from the last initialisation of
the bus, if any). If extra arguments are given, the bus is initialised.
See ``init`` for parameters of initialisation.
Methods
-------
.. method:: SPI.init(baudrate=1000000, \*, polarity=0, phase=0, bits=8, firstbit=SPI.MSB, pins=(CLK, MOSI, MISO), sck=None, mosi=None, miso=None)
Initialise the SPI bus with the given parameters:
- ``baudrate`` is the SCK clock rate.
- ``polarity`` can be 0 or 1, and is the level the idle clock line sits at.
- ``phase`` can be 0 or 1 to sample data on the first or second clock edge
respectively.
- ``bits`` is the width in bits of each transfer. Only 8 is guaranteed to be supported by all hardware.
- ``firstbit`` can be ``SPI.MSB`` or ``SPI.LSB``.
- ``pins`` is an optional tuple with the pins to assign to the SPI bus (deprecated, only for WiPy).
- ``sck``, ``mosi``, ``miso`` are pins (machine.Pin) objects to use for bus signals. For most
hardware SPI blocks (as selected by ``id`` parameter to the constructore), pins are fixed
and cannot be changed. In some cases, hardware blocks allow 2-3 alternative pin sets for
a hardware SPI block. Arbitrary pin assignments are possible only for a bitbanging SPI driver
(``id``=-1).
.. method:: SPI.deinit()
Turn off the SPI bus.
.. method:: SPI.read(nbytes, write=0x00)
Read a number of bytes specified by ``nbytes`` while continuously writing
the single byte given by ``write``.
Returns a ``bytes`` object with the data that was read.
.. method:: SPI.readinto(buf, write=0x00)
Read into the buffer specified by ``buf`` while continuously writing the
single byte given by ``write``.
Returns ``None``.
Note: on WiPy this function returns the number of bytes read.
.. method:: SPI.write(buf)
Write the bytes contained in ``buf``.
Returns ``None``.
Note: on WiPy this function returns the number of bytes written.
.. method:: SPI.write_readinto(write_buf, read_buf)
Write the bytes from ``write_buf`` while reading into ``read_buf``. The
buffers can be the same or different, but both buffers must have the
same length.
Returns ``None``.
Note: on WiPy this function returns the number of bytes written.
Constants
---------
.. data:: SPI.MASTER
for initialising the SPI bus to master; this is only used for the WiPy
.. data:: SPI.MSB
set the first bit to be the most significant bit
.. data:: SPI.LSB
set the first bit to be the least significant bit