mirrors
/
micropython
mirror of https://github.com/micropython/micropython.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
micropython/ports/stm32/boards/OLIMEX_E407/mpconfigboard.h

81 lines
2.8 KiB
C
Raw Normal View History

stmhal: Add board definition files for Olimex STM32-E407.
2016-06-04 23:57:50 +01:00
#define STM32E407
#define MICROPY_HW_BOARD_NAME "OLIMEX STM32-E407"
#define MICROPY_HW_MCU_NAME "STM32F407"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_HAS_SDCARD (1)
#define MICROPY_HW_HAS_MMA7660 (0)
#define MICROPY_HW_HAS_LIS3DSH (0)
#define MICROPY_HW_HAS_LCD (0)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_TIMER (1)
#define MICROPY_HW_ENABLE_SERVO (0)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_CAN (1)
// HSE is 12MHz
#define MICROPY_HW_CLK_PLLM (12)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
// UART config
stmhal: Refactor UART configuration to use pin objects. This follows the pattern of other peripherals (I2C, SPI) to specify the pins using pin objects instead of a pair of GPIO port and pin number. It makes it easier to customise the UART pins for a particular board.
2016-12-05 01:21:45 +00:00
#define MICROPY_HW_UART1_TX (pin_B6)
#define MICROPY_HW_UART1_RX (pin_B7)
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART2_RTS (pin_A1)
#define MICROPY_HW_UART2_CTS (pin_A0)
#define MICROPY_HW_UART3_TX (pin_D8)
#define MICROPY_HW_UART3_RX (pin_D9)
#define MICROPY_HW_UART3_RTS (pin_D12)
#define MICROPY_HW_UART3_CTS (pin_D11)
stmhal: Add board definition files for Olimex STM32-E407.
2016-06-04 23:57:50 +01:00
#if MICROPY_HW_HAS_SWITCH == 0
// NOTE: A0 also connects to the user switch. To use UART4 you should
// set MICROPY_HW_HAS_SWITCH to 0, and also remove SB20 (on the back
// of the board near the USER switch).
stmhal: Refactor UART configuration to use pin objects. This follows the pattern of other peripherals (I2C, SPI) to specify the pins using pin objects instead of a pair of GPIO port and pin number. It makes it easier to customise the UART pins for a particular board.
2016-12-05 01:21:45 +00:00
#define MICROPY_HW_UART4_TX (pin_A0)
#define MICROPY_HW_UART4_RX (pin_A1)
stmhal: Add board definition files for Olimex STM32-E407.
2016-06-04 23:57:50 +01:00
#endif
stmhal: Refactor UART configuration to use pin objects. This follows the pattern of other peripherals (I2C, SPI) to specify the pins using pin objects instead of a pair of GPIO port and pin number. It makes it easier to customise the UART pins for a particular board.
2016-12-05 01:21:45 +00:00
#define MICROPY_HW_UART6_TX (pin_C6)
#define MICROPY_HW_UART6_RX (pin_C7)
stmhal: Add board definition files for Olimex STM32-E407.
2016-06-04 23:57:50 +01:00
// I2C busses
stmhal/boards: For OLIMEX_E407, enable UART1 and fix I2C1 mapping. UART1 can be used even if the switch is enabled. The schematics for this board make I2C1 available on PB8/PB9, even though it can also be mapped to PB6/PB7. See #2396 and #2427.
2016-09-19 04:00:15 +01:00
#define MICROPY_HW_I2C1_SCL (pin_B8)
#define MICROPY_HW_I2C1_SDA (pin_B9)
stmhal: Add board definition files for Olimex STM32-E407.
2016-06-04 23:57:50 +01:00
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_A0)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// LEDs
#define MICROPY_HW_LED1 (pin_C13)
stmhal/led: Refactor LED to use mp_hal_pin_output() init function. As part of this patch the MICROPY_HW_LED_OTYPE setting is removed because it is now unused (all boards anyway had this as OUTPUT_PP).
2016-10-18 04:43:05 +01:00
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin))
stmhal: Add board definition files for Olimex STM32-E407.
2016-06-04 23:57:50 +01:00
// SD card detect switch
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C11)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
// USB config
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)